| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Implement XDP_TX verdict and ndo_xdp_xmit net_device_ops function
pointer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow tx buffer array to contain both skb and xdp buffers in order to
enable xdp frame recycling adding XDP_TX verdict support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move data buffer prefetch in mvneta_swbm_rx_frame after
dma_sync_single_range_for_cpu
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic XDP support to mvneta driver for devices that rely on software
buffer management. Currently supported verdicts are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_ABORTED
- iptables drop:
$iptables -t raw -I PREROUTING -p udp --dport 9 -j DROP
$nstat -n && sleep 1 && nstat
IpInReceives 151169 0.0
IpExtInOctets 6953544 0.0
IpExtInNoECTPkts 151165 0.0
- XDP_DROP via xdp1
$./samples/bpf/xdp1 3
proto 0: 421419 pkt/s
proto 0: 421444 pkt/s
proto 0: 421393 pkt/s
proto 0: 421440 pkt/s
proto 0: 421184 pkt/s
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor mvneta_rx_swbm code introducing mvneta_swbm_rx_frame and
mvneta_swbm_add_rx_fragment routines. Rely on build_skb in oreder to
allocate skb since the previous patch introduced buffer recycling using
the page_pool API.
This patch fixes even an issue in the original driver where dma buffers
are accessed before dma sync.
mvneta driver can run on not cache coherent devices so it is
necessary to sync DMA buffers before sending them to the device
in order to avoid memory corruptions. Running perf analysis we can
see a performance cost associated with this DMA-sync (anyway it is
already there in the original driver code). In follow up patches we
will add more logic to reduce DMA-sync as much as possible.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the page_pool api for allocations and DMA handling instead of
__dev_alloc_page()/dma_map_page() and free_page()/dma_unmap_page().
Pages are unmapped using page_pool_release_page before packets
go into the network stack.
The page_pool API offers buffer recycling capabilities for XDP but
allocates one page per packet, unless the driver splits and manages
the allocated page.
This is a preliminary patch to add XDP support to mvneta driver
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce mvneta_update_stats routine to collect {rx/tx} statistics
(packets and bytes). This is a preliminary patch to add XDP support to
mvneta driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filter table array not implemented yet and shadow_vfta pointer
not used. Clean up the code and remove the unused shadow_vfta pointer.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Extend the socket buffer field process and add Rx checksum functionality
Minor: fix indentation with tab instead of spaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add multicast addresses list to the MTA table.
Implement basic Rx mode support.
Add option for IPv6 address settings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement flow for S0ix support. Modern SoCs support S0ix low power
states during idle periods, which are sub-states of ACPI S0 that increase
power saving while supporting an instant-on experience for providing
lower latency that ACPI S0. The S0ix states shut off parts of the SoC
when they are not in use, while still maintaning optimal performance.
This patch add support for S0ix started from an Ice Lake platform.
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add stream control transmission protocol CRC checksum.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When device is resetting, the CMDQ service may be stopped until
reset completed. If a new RAS error occurs at this moment, it
will no be able to clear the RAS source. This patch fixes it
by clear the RAS source after reset complete.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, napi_alloc_skb() is used to allocate skb for fraglist
when the head skb is not enough to hold the remaining data, and
the remaining data is added to the frags part of the fraglist skb,
leaving the linear part unused.
So this patch passes length of 0 to allocate fraglist skb with
zero size of linear data.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit e55970950556 ("net: hns3: Add handling of GRO Pkts
not fully RX'ed in NAPI poll"), ring->skb is used to record the
current SKB when processing the RX BD in hns3_handle_rx_bd(),
so the parameter out_skb is unnecessary.
This patch also adjusts the err checking to reduce duplication
in hns3_handle_rx_bd(), and "err == -ENXIO" is rare case, so put
it in the unlikely annotation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since struct hns3_enet_ring is a frequently used in critical data
path, so make it cacheline aligned as struct hns3_enet_tqp_vector.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few places that need to access the netdev of a ring
through ring->tqp->handle->kinfo.netdev, and ring->tqp is a struct
which both in enet and hclge modules, it is better to use the
struct that is only used in enet module.
This patch adds the ring_to_netdev() to access the netdev of ring
through ring->tqp_vector->napi.dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the TX and RX ring in a queue is bounded to the
same IRQ, there may be unnecessary barrier op when only one of
the ring need to be processed.
This patch adjusts the location of rmb() in hns3_clean_tx_ring()
and adds a checking in hns3_clean_rx_ring() to avoid unnecessary
barrier op when there is nothing to do for the ring.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac_addr_hi32 and mac_addr_lo16 are used to store the MAC address
for management table. But using array of mac_addr[ETH_ALEN] would
be more general and not need to care about the big-endian mode of
the CPU.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the queue_index field in struct hns3_nic_ring_data is
used, other field is unused and unnecessary for hns3 driver,
so this patch removes it and move the queue_index field to
hns3_enet_ring.
This patch also removes an unused struct hns_queue declaration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes which were for the most
part trivially resolvable.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
|
|
Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.
In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.
For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.
Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().
Remove the superfluous module_put().
Fixes: 279f438e36c0a7 ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).
This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.
This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When connected to a micrel phy, phy_find_first doesn't work properly
because the first phy found is on address 0, the broadcast address but, the
first thing the phy driver is doing is disabling this broadcast address.
The phy is then available only on address 1 but the mdio driver doesn't
know about it.
Instead, register the mdio bus using of_mdiobus_register and try to find
the phy description in device tree before falling back to phy_find_first.
This ultimately also allows to describe the interrupt the phy is connected
to.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.
Change the order to close this race condition.
Fixes: 92571a1aae40 ("lan78xx: Connect phy early")
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.
Fix this by pushing the skb's data pointer to the start of the packet.
Fixes: b5ce611fd96e ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch supports an enhanced switched port analyzer that enables
selecting network traffic for analysis by a network analyzer.
SPAN agents are configured and consumed whenever a tc filter is added
with a mirror action to a new destination. The destination can either be
a physical port (e.g., swp1), a VLAN device or a gretap.
Expose the maximum number of SPAN agents and their current usage to the
user.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507bf ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 28b2e0d2cd13 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272acaaa ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there's a bug in the module subsystem [0] preventing load of
the PHY driver module on certain systems (as one symptom).
This results in a NPE on such systems for the following reason:
Instead of the correct PHY driver the genphy driver is loaded that
doesn't implement the read_page/write_page callbacks. Every call to
phy_read_paged() et al will result in a NPE therefore.
In parallel to fixing the root cause we should make sure that this one
and maybe similar issues in other subsystems don't result in a NPE
in phylib. So let's check for the callbacks before using them and warn
once if they are not available.
[0] https://marc.info/?t=157072642100001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjusting the hardware clock (PTPCLKVAL, PTPCLKADD, PTPCLKRATE) is a
requirement for the auxiliary PTP functionality of the switch
(TTEthernet, PPS input, PPS output).
Therefore we need to switch to using these registers to keep a
synchronized time in hardware, instead of the timecounter/cyclecounter
implementation, which is reliant on the free-running PTPTSCLK.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf_xdp_adjust_head() can change the frame boundaries. Account for the
potential shift properly by calculating the new offset before
syncing the buffer to the device for XDP_TX
Fixes: ba2b232108d3 ("net: netsec: add XDP support")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.
Fix the warning (and possible bug) from sparse:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: got struct mac_device_info *hw
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c9255 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.
v2: fix syntax error
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increment netdev rx counters even for XDP_DROP verdict. Report even
tx bytes for xdp buffers (TYPE_NETSEC_XDP_TX or TYPE_NETSEC_XDP_NDO).
Moreover account pending buffer length in netsec_xdp_queue_one as it is
done for skb counterpart
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
disable ptp_ref_clk in suspend flow, and enable it in resume flow.
Fixes: f573c0b9c4e0 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than parsing the sfp firmware node in phylink, parse it in the
sfp-bus code, so we can re-use this code for PHYs without having to
duplicate the parsing.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Lorenzo Bianconi
Sasha Neftin
Jian Shen
Yunsheng Lin
Guojia Liao
David S. Miller
Linus Torvalds
Mans Rullgard
Chenwandun
Michael Tretter
Juergen Gross
Yonglong Liu
Alexandre Belloni
Andrew Lunn
Ido Schimmel
Danielle Ratson
Doug Berger
Heiner Kallweit
Vladimir Oltean
Marek Vasut
Ilias Apalodimas
Ben Dooks (Codethink)
Ioana Radulescu
Florin Chiculita
Oliver Neukum
Biao Huang
Russell King