| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The counter variable wasn't increased at all which may stuck under
certain circumstances.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since e9ce7cb6b107 ("xen-netback: Factor queue-specific data into queue struct"),
the transimt shaper timeout is always set to 0. The value the user sets via
xenbus is never propagated to the transmit shaper.
This patch fixes the issue.
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support ndo_features_check to avoid:
- the transport offset is more than the hw limitation when using hw checksum.
- the skb->len of a GSO packet is more than the limitation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When allocation of all RQs fail, we do not free previously allocated buffers,
before returning error. This causes memory leak.
This patch fixes this by calling vnic_rq_clean(), which frees all the rq
buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948d2 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the
old MTT's page shift, which could result in using an incorrect offset.
Fix the initialization to be after we calculate the new MTT offset.
In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This
is necessary in order to mark the MTT as invalid and avoid freeing it later.
Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the check of adapter fails and goes into the 'else' branch, the
return value 'err' should not still be zero.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
The patch also modifies the test of mgp->cmd to satisfy checkpatch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove a FIXME comment that was missed in a commit on 1/2007.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: nick <xerofoify@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Although it doesn't explicitly say so, commit 60ffa478759f39a2 ("e100:
Fix MDIO/MDIO-X") appears to be intended to revert the earlier commit
648951451e6d2d53 ("e100: fixed e100 MDI/MDI-X issues"). However,
careful examination reveals that the attempted revert actually
_inverted_ the test for eeprom_mdix_enabled. That is bound to program
a few PHYs incorrectly...
https://bugzilla.redhat.com/show_bug.cgi?id=1156417
Signed-off-by: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For linux-3.18.0
The driver lacks pci_disable_device in error handling code of
ne2k_pci_init_one, so the device enabled by pci_enable_device is not
disabled when errors occur.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In __bond_release_one(), when the interface is not a slave or not a slave of
"this" master, it log error message.
The message actually should be a debug message matching what bond_enslave()
does.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Paul made a Kconfig dependency fix to ipw2200, it was not possible to
enable that driver because Wireless Extensions is now disabled by default.
o Mika fixed brcmfmac not to crash when platform data is not populated
o Emmanuel provided few fixes to iwlwifi, he says:
"I have here new device IDs and a fix for double free bug I
introduced. I also fix an issue with the RFKILL interrupt - the HW
needs us to ACK the interrupt again after we reset it. Liad fixes an
issue with the firmware debugging infrastructure. While working on
torture scenarios of firmware restarts, Eliad found an issue which
he fixed."
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f22 ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The second init_completion call should be a reinit_completion here.
patch is against 3.18.0 linux-next
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This property is no longer used in the code yet the code looks for it in the device tree.
It does not cause an error if it's not in the tree.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use generic config_init callback also for KSZ8021 and KSZ8031.
This has been avoided this far due to commit b838b4aced99 ("phy/micrel:
KSZ8031RNL RMII clock reconfiguration bug"), which claims that the PHY
becomes unresponsive if the broadcast-disable flag is set before
configuring the clock mode.
Turns out that the problem seemingly worked-around by the above
mentioned commit was really due to a hardware-configuration issue, where
the PHY was in fact strapped to address 3 rather than 0.
Tested-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver looks for pdata->oob_irq_supported to find out if wowl can be
supported. However, not all platforms populate pdata in which case we crash
the kernel because of NULL pointer dereference.
Fixes: 330b4e4be937 ("brcmfmac: Add wowl support for SDIO devices.")
Reported-by: Christophe Prigent <christophe.prigent@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Commit 24a0aa212ee2 ("cfg80211: make WEXT compatibility unselectable")
made it impossible to depend on CFG80211_WEXT. It does still allow to
select that symbol. (Yes, the commit summary is confusing.)
So make IPW2200 select CFG80211_WEXT, so that the ipw2200 driver can be
enabled in config again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In case of error vxlan_xmit_one() can free already freed skb.
Also fixes memory leak of dst-entry.
Fixes: acbf74a7630 ("vxlan: Refactor vxlan driver to make use
of the common UDP tunnel functions").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Decode and display Port Type and Module Type for ethtool get_settings() call
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit d75b1ade567ffab085e8adbbdacf0092d10cd09c (net: less
interrupt masking in NAPI) breaks caif.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers caif tries to do a last-ditch check and if there is
more work it will call napi_schedule and then immediately process
some of this new work. Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in caif.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
iowrite32() will byteswap it's argument on big endian archs.
iowrite32be() will byteswap on little endian archs.
Since we don't want to do this unnecessary byteswap on the fast path,
doorbell is stored in the NIC's native endianness. Using the right
iowrite() according to the arch endianness.
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: David Laight <david.laight@aculab.com>
Fixes: 6a4e812 ("net/mlx4_en: Avoid calling bswap in tx fast path")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For linux-3.18.0
The driver lacks netif_napi_del in the normal path and error path
to match the call of netif_napi_add in rtl8139_init_one.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For linux-3.18.0
When pci_request_regions is failed in rtl8139_init_board, pci_disable_device
is not called to disable the device which are enabled by pci_enable_device,
because of disable_dev_on_err is not assigned 1.
This patch fix this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The s6000 Xtensa support has been removed from the kernel in
4006e565e1500db4. There are no other chips using this driver.
While the Mentor/Alcatel PE-MCXMAC IP core is also used in other
designs (Freescale Gianfar/UCC, QLogic NetXen, Solarflare, Agere
ET-1310, Netlogic XLR/XLS), none of these use this driver as it
heavily depends on the s6000 DMA engine. In fact, there is no
code sharing across any of the aforementioned devices.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the function port_cfg_dis_learn() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Please queue for -stable.
Reported-by: Nils Holland <nholland@tisys.org>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The changed names are union fields with the same size, so the existing code
still works. But, we now update these variables to the correct names.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit d75b1ade567ffab085e8adbbdacf0092d10cd09c (net: less
interrupt masking in NAPI) breaks virtio_net in an insidious way.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers virtio_net tries to do a last-ditch check and if
there is more work it will call napi_schedule and then immediately
process some of this new work. Should the entire budget be consumed
while processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in virtio_net.
The worst part of this bug is that the list corruption causes other
napi users to be moved off-list. In my case I was chasing a stall
in IPsec (IPsec uses netif_rx) and I only belatedly realised that it
was virtio_net which caused the stall even though the virtio_net
poll was still functioning perfectly after IPsec stalled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both stmmac_open() and stmmac_resume() call stmmac_hw_setup(), and
stmmac_hw_setup() call stmmac_init_ptp() unconditionally. However, only
stmmac_release() calls stmmac_release_ptp(). Since stmmac_suspend()
doesn't call stmmac_release_ptp(), stmmac_resume() also needn't call
stmmac_init_ptp().
This patch also fix a "scheduling while atomic" problem when resume
from suspend/hibernation. Because stmmac_init_ptp() will trigger
scheduling while stmmac_resume() hold a spinlock.
Callgraph of "scheduling while atomic":
stmmac_resume() --> stmmac_hw_setup() --> stmmac_init_ptp() -->
stmmac_ptp_register() --> ptp_clock_register() --> device_create() -->
device_create_groups_vargs() --> device_add() --> devtmpfs_create_node()
--> wait_for_common() --> schedule_timeout() --> __schedule()
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I have here new device IDs and a fix for double free bug I introduced.
I also fix an issue with the RFKILL interrupt - the HW needs us to ACK
the interrupt again after we reset it.
Liad fixes an issue with the firmware debugging infrastructure.
While working on torture scenarios of firmware restarts, Eliad found an
issue which he fixed.
|
|
Hardware always provides compliment of IP pseudo checksum. Stack expects
whole packet checksum without pseudo checksum if CHECKSUM_COMPLETE is set.
This causes checksum error in nf & ovs.
kernel: qg-19546f09-f2: hw csum failure
kernel: CPU: 9 PID: 0 Comm: swapper/9 Tainted: GF O-------------- 3.10.0-123.8.1.el7.x86_64 #1
kernel: Hardware name: Cisco Systems Inc UCSB-B200-M3/UCSB-B200-M3, BIOS B200M3.2.2.3.0.080820141339 08/08/2014
kernel: ffff881218f40000 df68243feb35e3a8 ffff881237a43ab8 ffffffff815e237b
kernel: ffff881237a43ad0 ffffffff814cd4ca ffff8829ec71eb00 ffff881237a43af0
kernel: ffffffff814c6232 0000000000000286 ffff8829ec71eb00 ffff881237a43b00
kernel: Call Trace:
kernel: <IRQ> [<ffffffff815e237b>] dump_stack+0x19/0x1b
kernel: [<ffffffff814cd4ca>] netdev_rx_csum_fault+0x3a/0x40
kernel: [<ffffffff814c6232>] __skb_checksum_complete_head+0x62/0x70
kernel: [<ffffffff814c6251>] __skb_checksum_complete+0x11/0x20
kernel: [<ffffffff8155a20c>] nf_ip_checksum+0xcc/0x100
kernel: [<ffffffffa049edc7>] icmp_error+0x1f7/0x35c [nf_conntrack_ipv4]
kernel: [<ffffffff814cf419>] ? netif_rx+0xb9/0x1d0
kernel: [<ffffffffa040eb7b>] ? internal_dev_recv+0xdb/0x130 [openvswitch]
kernel: [<ffffffffa04c8330>] nf_conntrack_in+0xf0/0xa80 [nf_conntrack]
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffffa049e302>] ipv4_conntrack_in+0x22/0x30 [nf_conntrack_ipv4]
kernel: [<ffffffff815005ca>] nf_iterate+0xaa/0xc0
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81500664>] nf_hook_slow+0x84/0x140
kernel: [<ffffffff81509380>] ? inet_del_offload+0x40/0x40
kernel: [<ffffffff81509dd4>] ip_rcv+0x344/0x380
Hardware verifies IP & tcp/udp header checksum but does not provide payload
checksum, use CHECKSUM_UNNECESSARY. Set it only if its valid IP tcp/udp packet.
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Stefan Assmann <sassmann@redhat.com>
Reported-by: Sunil Choudhary <schoudha@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when skb_gso_segment returns error, the original skb should be freed
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.19:
- On-demand paging support in core midlayer and mlx5 driver. This
lets userspace create non-pinned memory regions and have the
adapter HW trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (56 commits)
IB/mlx5: Implement on demand paging by adding support for MMU notifiers
IB/mlx5: Add support for RDMA read/write responder page faults
IB/mlx5: Handle page faults
IB/mlx5: Page faults handling infrastructure
IB/mlx5: Add mlx5_ib_update_mtt to update page tables after creation
IB/mlx5: Changes in memory region creation to support on-demand paging
IB/mlx5: Implement the ODP capability query verb
mlx5_core: Add support for page faults events and low level handling
mlx5_core: Re-add MLX5_DEV_CAP_FLAG_ON_DMND_PG flag
IB/srp: Allow newline separator for connection string
IB/core: Implement support for MMU notifiers regarding on demand paging regions
IB/core: Add support for on demand paging regions
IB/core: Add flags for on demand paging support
IB/core: Add support for extended query device caps
IB/mlx5: Add function to read WQE from user-space
IB/core: Add umem function to read data from user-space
IB/core: Replace ib_umem's offset field with a full address
IB/mlx5: Enhance UMR support to allow partial page table update
IB/mlx5: Remove per-MR pas and dma pointers
RDMA/ocrdma: Always resolve destination mac from GRH for UD QPs
...
|
|
An earlier commit to resolve an issue with encapsulation offloads missed
setting a bit in the outer netdev features flag. This results in loss of TSO
feature on a VxLAN interface.
Fixes: 630f4b70 ("Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Noticed when debugging ptp.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bc96f648df1bbc2729abbb84513cf4f64273a1f1 (xen-netback: make
feature-rx-notify mandatory) incorrectly assumed that there were no
frontends in use that did not support this feature. But the frontend
driver in MiniOS does not and since this is used by (qemu) stubdoms,
these stopped working.
Netback sort of works as-is in this mode except:
- If there are no Rx requests and the internal Rx queue fills, only
the drain timeout will wake the thread. The default drain timeout
of 10 s would give unacceptable pauses.
- If an Rx stall was detected and the internal Rx queue is drained,
then the Rx thread would never wake.
Handle these two cases (when feature-rx-notify is disabled) by:
- Reducing the drain timeout to 30 ms.
- Disabling Rx stall detection.
Reported-by: John <jw@nuclearfallout.net>
Tested-by: John <jw@nuclearfallout.net>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QSA module was getting decoded as QSFP module in ethtool get settings, this
patch fixes it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba773 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit contains 2 fixes for the 128B CQE/EQE stride feaure.
Wei found that mlx4_QUERY_HCA function marked the wrong capability
in flags (64B CQE/EQE), when CQE/EQE stride feature was enabled.
Also added small fix in initial CQE ownership bit assignment, when CQE
is size is not default 32B.
Fixes: 77507aa24 (net/mlx4: Enable CQE/EQE stride support)
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do camera capture test on i.MX6q sabresd board, and save the capture data to
nfs rootfs. The command is:
gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t !
queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937
blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse !
queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov
After about 10 hours running, there have net watchdog timeout kernel dump:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8()
NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440
[<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14)
[<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0)
[<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c)
[<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40)
[<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8)
[<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c)
[<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220)
[<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c)
[<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4)
[<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4)
[<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c)
[<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74)
Exception stack(0x80d27f18 to 0x80d27f60)
7f00: 80d27f60 0000014c
7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000
7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff
[<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0)
[<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154)
[<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44)
[<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158)
[<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368)
---[ end trace 09ebd32fb032f86d ]---
...
There might have a race in napi_schedule(), leaving interrupts disabled forever.
After these patch, the case still work more than 40 hours running.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Andy Shevchenko
Palik, Imre
hayeswang
Felipe Balbi
Govindarajulu Varadarajan
Kristian Evensen
Kostya Belezko
Jack Morgenstein
Maor Gottlieb
Yongjian Xu
Julia Lawall
Joe Perches
Todd Fujinaka
John W. Linville
Jia-Ju Bai
Wengang Wang
David S. Miller
Jesse Gross
Nicholas Mc Guire
Appana Durga Kedareswara Rao
Johan Hovold
Mika Westerberg
Paul Bolle
Pravin B Shelar
Hariprasad Shenai
Herbert Xu
Amir Vadai
Wolfram Sang
Daniel Glöckner
Rickard Strandqvist
Prashant Sreedharan
Haiyang Zhang
Huacai Chen
Kalle Valo
Li RongQing
Linus Torvalds
Sriharsha Basavapatna
Jiri Benc
David Vrabel
Or Gerlitz
Ido Shamay
Nimrod Andy