| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull xen fix from Juergen Gross:
"A single patch fixing a Xen related security bug: a malicious guest
might be able to trigger a 'use after free' issue in the xen-netback
driver"
* tag 'for-linus-5.13b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-netback: take a reference to the RX task thread
|
|
Use the new recycling API for page_pool.
In a drop rate test, the packet rate increased by 10%,
from 296 Kpps to 326 Kpps.
perf top on a stock system shows:
Overhead Shared Object Symbol
23.66% [kernel] [k] __pi___inval_dcache_area
22.85% [mvneta] [k] mvneta_rx_swbm
7.54% [kernel] [k] kmem_cache_alloc
6.49% [kernel] [k] eth_type_trans
3.94% [kernel] [k] dev_gro_receive
3.91% [kernel] [k] __netif_receive_skb_core
3.91% [kernel] [k] kmem_cache_free
3.76% [kernel] [k] page_pool_release_page
3.56% [kernel] [k] free_unref_page
2.40% [kernel] [k] build_skb
1.49% [kernel] [k] skb_release_data
1.45% [kernel] [k] __alloc_pages_bulk
1.30% [kernel] [k] page_frag_free
And this is the same output with recycling enabled:
Overhead Shared Object Symbol
26.41% [kernel] [k] __pi___inval_dcache_area
25.00% [mvneta] [k] mvneta_rx_swbm
8.14% [kernel] [k] kmem_cache_alloc
6.84% [kernel] [k] eth_type_trans
4.44% [kernel] [k] __netif_receive_skb_core
4.38% [kernel] [k] kmem_cache_free
4.16% [kernel] [k] dev_gro_receive
3.21% [kernel] [k] page_pool_put_page
2.41% [kernel] [k] build_skb
1.82% [kernel] [k] skb_release_data
1.61% [kernel] [k] napi_gro_receive
1.25% [kernel] [k] page_pool_refill_alloc_cache
1.16% [kernel] [k] __netif_receive_skb_list_core
We can see that page_pool_release_page(), free_unref_page() and
__alloc_pages_bulk() are no longer on top of the list when receiving
traffic.
The test was done with mausezahn on the TX side with 64 byte raw
ethernet frames.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new recycling API for page_pool.
In a drop rate test, the packet rate is almost doubled,
from 1110 Kpps to 2128 Kpps.
perf top on a stock system shows:
Overhead Shared Object Symbol
34.88% [kernel] [k] page_pool_release_page
8.06% [kernel] [k] free_unref_page
6.42% [mvpp2] [k] mvpp2_rx
6.07% [kernel] [k] eth_type_trans
5.18% [kernel] [k] __netif_receive_skb_core
4.95% [kernel] [k] build_skb
4.88% [kernel] [k] kmem_cache_free
3.97% [kernel] [k] kmem_cache_alloc
3.45% [kernel] [k] dev_gro_receive
2.73% [kernel] [k] page_frag_free
2.07% [kernel] [k] __alloc_pages_bulk
1.99% [kernel] [k] arch_local_irq_save
1.84% [kernel] [k] skb_release_data
1.20% [kernel] [k] netif_receive_skb_list_internal
With packet rate stable at 1100 Kpps:
tx: 0 bps 0 pps rx: 532.7 Mbps 1110 Kpps
tx: 0 bps 0 pps rx: 532.6 Mbps 1110 Kpps
tx: 0 bps 0 pps rx: 532.4 Mbps 1109 Kpps
tx: 0 bps 0 pps rx: 532.1 Mbps 1109 Kpps
tx: 0 bps 0 pps rx: 531.9 Mbps 1108 Kpps
tx: 0 bps 0 pps rx: 531.9 Mbps 1108 Kpps
And this is the same output with recycling enabled:
Overhead Shared Object Symbol
12.91% [kernel] [k] eth_type_trans
12.54% [mvpp2] [k] mvpp2_rx
9.67% [kernel] [k] build_skb
9.63% [kernel] [k] __netif_receive_skb_core
8.44% [kernel] [k] page_pool_put_page
8.07% [kernel] [k] kmem_cache_free
7.79% [kernel] [k] kmem_cache_alloc
6.86% [kernel] [k] dev_gro_receive
3.19% [kernel] [k] skb_release_data
2.41% [kernel] [k] netif_receive_skb_list_internal
2.18% [kernel] [k] page_pool_refill_alloc_cache
1.76% [kernel] [k] napi_gro_receive
1.61% [kernel] [k] kfree_skb
1.20% [kernel] [k] dma_sync_single_for_device
1.16% [mvpp2] [k] mvpp2_poll
1.12% [mvpp2] [k] mvpp2_read
With packet rate above 2100 Kpps:
tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps
tx: 0 bps 0 pps rx: 1021 Mbps 2127 Kpps
tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps
tx: 0 bps 0 pps rx: 1021 Mbps 2128 Kpps
tx: 0 bps 0 pps rx: 1022 Mbps 2128 Kpps
tx: 0 bps 0 pps rx: 1022 Mbps 2129 Kpps
The major performance increase is explained by the fact that the most CPU
consuming functions (page_pool_release_page, page_frag_free and
free_unref_page) are no longer called on a per packet basis.
The test was done by sending to the macchiatobin 64 byte ethernet frames
with an invalid ethertype, so the packets are dropped early in the RX path.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a prerequisite patch, the next one is enabling recycling of
skbs and fragments. Add an extra argument on __skb_frag_unref() to
handle recycling, and update the current users of the function with that.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function 'pnic2_lnk_change' is declared twice, so remove the
repeated declaration.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier patches have decoupled the MSI-X conveyed error handling
and recovery logic. This earlier concept code is no longer required.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling & recovery is done in context of reset task which
gets scheduled from misc interrupt handler in existing code. But
since error handling has been moved to new task, it should get
scheduled instead of the reset task from the interrupt handler.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Error handling and recovery logic are intertwined. Error handling (i.e.
error identification, clearing error sources and initiation of recovery)
is done in context of reset task. If certain hardware errors get
delivered during driver init time, which can cause driver init/loading
to fail.
Introduce a separate error handling task to ensure below:
1. Reset logic remains independent of the error handling logic.
2. Add the hclge_errhand_task_schedule to schedule error recovery
tasks, This will ensure that common misellaneous MSI-X interrupt are
re-enabled quickly.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up the following includecheck warning:
./drivers/net/ethernet/qlogic/qed/qed_nvmetcp_fw_funcs.h: linux/kernel.h
is included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
unbind() is the proper place to disconnect PHY, but it will fail if
netdev is already unregistered.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case phy_state_machine() works on top of USB device, we can get -ENODEV
at any point. So, be less noisy if device was removed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This usb devices can be removed at any time, so we need to forward
correct error value if device was detached.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With working phylib support we are able now to use generic selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able to use ax88772 with external PHYs and use advantage of
existing PHY drivers, we need to port at least ax88772 part of asix
driver to the phylib framework.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for build-in x88772A/C PHYs
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor asix_read_phy_addr() to return usable error value directly and
make sure all callers handle this error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make resource management easier, use devm_kzalloc().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thermal polling delay argument for modules and gearboxes thermal zones
used to be initialized with zero value, while actual delay was used to
be set by mlxsw_thermal_set_mode() by thermal operation callback
set_mode(). After operations set_mode()/get_mode() have been removed by
cited commits, modules and gearboxes thermal zones always have polling
time set to zero and do not perform temperature monitoring.
Set non-zero "polling_delay" in thermal_zone_device_register() routine,
thus, the relevant thermal zones will perform thermal monitoring.
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Fixes: 5d7bd8aa7c35 ("thermal: Simplify or eliminate unnecessary set_mode() methods")
Fixes: 1ee14820fd8e ("thermal: remove get_mode() operation of drivers")
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mlxsw Qdisc offload, find_class() is an operation that yields a qdisc
offload descriptor given a parental qdisc descriptor and a class handle. In
__mlxsw_sp_qdisc_ets_graft() however, a band number is passed to that
function instead of a handle. This can lead to a trigger of a WARN_ON
with the following splat:
WARNING: CPU: 3 PID: 808 at drivers/net/ethernet/mellanox/mlxsw/spectrum_qdisc.c:1356 __mlxsw_sp_qdisc_ets_graft+0x115/0x130 [mlxsw_spectrum]
[...]
Call Trace:
mlxsw_sp_setup_tc_prio+0xe3/0x100 [mlxsw_spectrum]
qdisc_offload_graft_helper+0x35/0xa0
prio_graft+0x176/0x290 [sch_prio]
qdisc_graft+0xb3/0x540
tc_modify_qdisc+0x56a/0x8a0
rtnetlink_rcv_msg+0x12c/0x370
netlink_rcv_skb+0x49/0xf0
netlink_unicast+0x1f6/0x2b0
netlink_sendmsg+0x1fb/0x410
____sys_sendmsg+0x1f3/0x220
___sys_sendmsg+0x70/0xb0
__sys_sendmsg+0x54/0xa0
do_syscall_64+0x3a/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
Since the parent handle is not passed with the offload information, compute
it from the band number and qdisc handle.
Fixes: 28052e618b04 ("mlxsw: spectrum_qdisc: Track children per qdisc")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A max-shaper is the HW component responsible for delaying egress traffic
above a configured transmission rate. Burst size is the amount of traffic
that is allowed to pass without accounting. The burst size value needs to
be such that it can be expressed as 2^BS * 512 bits, where BS lies in a
certain ASIC-dependent range. mlxsw enforces that this holds before
attempting to configure the shaper.
The assumption for Spectrum-3 was that the lower limit of BS would be 5,
like for Spectrum-1. But as of now, the limit is still 11. Therefore fix
the driver accordingly, so that incorrect values are rejected early with a
proper message.
Fixes: 23effa2479ba ("mlxsw: reg: Add max_shaper_bs to QoS ETS Element Configuration")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not directly BUG() when there is hdr error, it is
better to output a print when such error happens. Currently,
the caller of xmit_skb() already did it.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug fixes overlapping feature additions and refactoring, mostly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add space required before the open parenthesis '('.
Add space required after that close brace '}'.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove redundant parentheses around 'cda >= desc_off'.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Block comments use * on subsequent lines.
Block comments use a trailing */ on a separate line.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Braces {} should be used on all arms of this statement.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trailing statements should be on next line.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the checkpatch error as "foo* bar" and should be "foo *bar",
and "(foo*)" should be "(foo *)".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the checkpatch error about missing a blank line
after declarations.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes some redundant blank lines.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that both RevMII as well as RevRMII exist, we can deprecate the
sja1105,role-mac and sja1105,role-phy properties and simply let the user
select that a port operates in MII PHY role by using
phy-mode = "rev-mii";
or in RMII PHY role by using
phy-mode = "rev-rmii";
There are no fixed-link MII or RMII properties in mainline device trees,
and the setup itself is fairly uncommon, so there shouldn't be risks of
breaking compatibility.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105 driver has an intermediate way of determining whether the
RGMII delays should be applied by the PHY or by itself: by looking at
the port role (PHY or MAC). The port can be put in the PHY role either
explicitly (sja1105,role-phy) or implicitly (fixed-link).
We want to deprecate the sja1105,role-phy property, so all that remains
is the fixed-link property. Introduce a "fixed_link" array of booleans
in the driver, and use that to determine whether RGMII delays must be
applied or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang generates deadcode.DeadStores warnings when a variable
is used to read a value, but then that value isn't used later
in the code. Fix this warning.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Failing to add or remove LLDP filter doesn't seem to be a fatal
error, so downgrade the dev_err message to a dev_dbg message.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
Linus Torvalds
Matteo Croce
Yang Yingliang
Shaokun Zhang
Yufeng Mo
Jiaran Zhang
Jiapeng Chong
David S. Miller
Oleksij Rempel
Zou Wei
Mykola Kostenok
Petr Machata
Xianting Tian
Peng Li
Vladimir Oltean
Paul M Stillwell Jr
Anirudh Venkataramanan
Jacob Keller