| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The purpose of system event handler is to handle system interrupts.
Such interrupts are raised to CPU from system programmable logic
devices, upon specific system wide changes, like line card activation
and deactivation.
The purpose is to create an alternative to trap mechanism, which
delivers these events to driver over PCI bus, but not available for
the driver working over I2C bus.
Mechanism is system dependent and applicable only for the systems
equipped with programmable devices with custom logic.
Add APIs for event handler registration and un-registration and API
which should be invoked from the registered callbacks when system
interrupt is raised to CPU.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, each line card is initialized using the following steps:
1. Initializing its various fields (e.g., slot index).
2. Creating the corresponding devlink object.
3. Enabling events (i.e., traps) for changes in line card status.
4. Querying and processing line card status.
Unlike traps, the IRQ that notifies the CPU about line card status
changes cannot be enabled / disabled on a per line card basis.
If a handler is registered before the line cards are initialized, the
handler risks accessing uninitialized memory.
On the other hand, if the handler is registered after initialization,
we risk missing events. For example, in step 4, the driver might see
that a line card is in ready state and will tell the device to enable
it. When enablement is done, the line card will be activated and the
IRQ will be triggered. Since a handler was not registered, the event
will be missed.
Solve this by splitting the initialization sequence into two steps
(1-2 and 3-4). In a subsequent patch, the handler will be registered
between both steps.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LRO/GRO_HW should be disabled if there is an attached XDP program.
BNXT_FLAG_TPA is the current setting of the LRO/GRO_HW. Using
BNXT_FLAG_TPA to disable LRO/GRO_HW will cause these features to be
permanently disabled once they are disabled.
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: b16b68918674 ("bnxt_en: Add SR-IOV support for 57500 chips.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing devlink_set_features() API for callbacks reload_down
and reload_up to function.
Fixes: 228ea8c187d8 ("bnxt_en: implement devlink dev reload driver_reinit")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using BNXT_PAGE_MODE_BUF_SIZE + offset as buffer length value is not
sufficient when running single buffer XDP programs doing redirect
operations. The stack will complain on missing skb tail room. Fix it
by using PAGE_SIZE when calling xdp_init_buff() for single buffer
programs.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case ftmac100 is used with a DSA switch, Linux wants to set MTU
to 1504 to accommodate for DSA overhead. With the default max_mtu
it leads to the error message:
ftmac100 92000000.mac eth0: error -22 setting MTU to 1504 to include DSA overhead
ftmac100 supports packet length 1518 (MAX_PKT_SIZE constant), so it is
safe to report it in max_mtu.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220821160844.474277-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Looks to have been left out in an oversight.
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Sainath Grandhi <sainath.grandhi@intel.com>
Fixes: 235a9d89da97 ('ipvtap: IP-VLAN based tap driver')
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220821130808.12143-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit f8217275b57aa48d98cc42051c2aac34152718d6.
There are a few more issues to fix that have been reported in the thread
for the original series [1]. We'll need to fix those before this will work.
So, revert it for now.
[1] - https://lore.kernel.org/lkml/CAMuHMdWo_wRwV-i_iyTxVnEsf3Th9GBAG+wxUQMQGnw1t2ijTg@mail.gmail.com/
Fixes: f8217275b57a ("net: mdio: Delete usage of driver_deferred_probe_check_state()")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220819221616.2107893-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently when we have 2 CPU ports configured for DSA tag_8021q mode and
we put them in a LAG, a PGID dump looks like this:
PGID_SRC[0] = ports 4,
PGID_SRC[1] = ports 4,
PGID_SRC[2] = ports 4,
PGID_SRC[3] = ports 4,
PGID_SRC[4] = ports 0, 1, 2, 3, 4, 5,
PGID_SRC[5] = no ports
(ports 0-3 are user ports, ports 4 and 5 are CPU ports)
There are 2 problems with the configuration above:
- user ports should enable forwarding towards both CPU ports, not just 4,
and the aggregation PGIDs should prune one CPU port or the other from
the destination port mask, based on a hash computed from packet headers.
- CPU ports should not be allowed to forward towards themselves and also
not towards other ports in the same LAG as themselves
The first problem requires fixing up the PGID_SRC of user ports, when
ocelot_port_assigned_dsa_8021q_cpu_mask() is called. We need to say that
when a user port is assigned to a tag_8021q CPU port and that port is in
a LAG, it should forward towards all ports in that LAG.
The second problem requires fixing up the PGID_SRC of port 4, to remove
ports 4 and 5 (in a LAG) from the allowed destinations.
After this change, the PGID source masks look as follows:
PGID_SRC[0] = ports 4, 5,
PGID_SRC[1] = ports 4, 5,
PGID_SRC[2] = ports 4, 5,
PGID_SRC[3] = ports 4, 5,
PGID_SRC[4] = ports 0, 1, 2, 3,
PGID_SRC[5] = no ports
Note that PGID_SRC[5] still looks weird (it should say "0, 1, 2, 3" just
like PGID_SRC[4] does), but I've tested forwarding through this CPU port
and it doesn't seem like anything is affected (it appears that PGID_SRC[4]
is being looked up on forwarding from the CPU, since both ports 4 and 5
have logical port ID 4). The reason why it looks weird is because
we've never called ocelot_port_assign_dsa_8021q_cpu() for any user port
towards port 5 (all user ports are assigned to port 4 which is in a LAG
with 5).
Since things aren't broken, I'm willing to leave it like that for now
and just document the oddity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This is a partial revert of commit c295f9831f1d ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Delete the redundant word 'was'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220708151538.51483-1-yuanjilin@cdjrlc.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
There is a possible race condition (use-after-free) like below
(FREE) | (USE)
adf7242_remove | adf7242_channel
cancel_delayed_work_sync |
destroy_workqueue (1) | adf7242_cmd_rx
| mod_delayed_work (2)
|
The root cause for this race is that the upper layer (ieee802154) is
unaware of this detaching event and the function adf7242_channel can
be called without any checks.
To fix this, we can add a flag write at the beginning of adf7242_remove
and add flag check in adf7242_channel. Or we can just defer the
destructive operation like other commit 3e0588c291d6 ("hamradio: defer
ax25 kfree after unregister_netdev") which let the
ieee802154_unregister_hw() to handle the synchronization. This patch
takes the second option.
Fixes: 58e9683d1475 ("net: ieee802154: adf7242: Fix OCL calibration
runs")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220808034224.12642-1-linma@zju.edu.cn
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
VF tunnel flow already exists and SF tunnel is the
same flow. Support offloading of tunneling over SF device
by allow to attach an encap route over SF and set to use
indirect flow table on SF.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move the creation of the rules from offloads fdb table init to
per rep vport init.
This way the driver will creating the send to vport meta rule
on any representor, e.g. SF representors.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Split esw_create_offloads_fdb_tables() into smaller functions.
This will help maintenance.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The ft_offloads table serves to steer packets, which are from the
eswitch, to the representor associated with the packets' source vport.
Previously, if a packet's source vport or metadata was not associated
with any representor, it was forwarded to the uplink representor. The
representor got packets it shouldn't have as they weren't coming from
the uplink vport.
One such effect of this breakage can be observed if the uplink
representor is attached to a bridge, where such illegal packets will
be broadcast to the remaining ports, flooding the switch with illegal
packets. In the case where IB loopback (e.g, SNAP) is enabled, all
transmitted packets would be looped back, and received by the uplink
representor, and result in an infinite feedback loop.
Therefore, block this hole by adding a default drop rule to the
ft_offloads table, so that all unmatched packets with no associated
representor are dropped.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Complete the decoupling process of flow steering from en.h.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Let all ttc creation be independent of priv, and pass relevant members
of priv only.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Decouple arfs flow steering functionality from priv.
Make all arfs functions defined under fs.h get flow_steering
struct as an argument, thus helping with the process of decoupling the
whole flow steering API from en.h.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Introduce flow steering debug macros family, fs_*.
These macros bring clean finish to the decoupling of flow steering
process such that all flow steering flows can report warnings and
provide debug information via these exclusive macros.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Create a new fs_ethtool.h header file, where ethtool steering init and
cleanup functions are declared in it.
Make mlx5e_ethtool_steering struct private and declare at en_fs_ethtool.c.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Let both mlx5e_ethtool_init_steering and mlx5e_ethtool_cleanup_steering
get ethtool steering struct as input instead of priv, as passing priv is
obsolete.
Also modify other function through the flow similarly.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Convert mlx5e_ethtool_steering member of mlx5e_flow_steering to a
pointer, and allocate dynamically for each profile at flow_steering
init.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Both mlx5e_ptp_alloc_rx_fs and mlx5e_ptp_free_rx_fs only
make use of two priv member, pass them directly instead.
This will help dropping priv from all en_fs file.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Make flow steering files fs_tcp.c/h independent of en.h
such that they go through the flow steering API only.
Make error reports be via mlx5_core API instead of netdev_err API, this
to ensure a safe decoupling from en.h, and prevent redundant argument
passing.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Make flow steering files fs_tt_redirect.c/h independent of en.h
such that it goes through the flow steering API only.
Make error reports be via mlx5_core API instead of netdev_err API, this
to ensure a safe decoupling from en.h, and prevent redundant argument
passing.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move mlx5e_flow_steering struct to fs_en.c to make it private.
Introduce flow_steering API and let other files go through it.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-18 (ixgbe)
This series contains updates to ixgbe driver only.
Fabio M. De Francesco replaces kmap() call to page_address() for
rx_buffer->page().
Jeff Daly adds a manual AN-37 restart to help resolve issues with some link
partners.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbe: Manual AN-37 for troublesome link partners for X550 SFI
ixgbe: Don't call kmap() on page allocated with GFP_ATOMIC
====================
Link: https://lore.kernel.org/r/20220818223402.1294091-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-18 (ice)
This series contains updates to ice driver only.
Jesse and Anatolii add support for controlling FCS/CRC stripping via
ethtool.
Anirudh allows for 100M speeds on devices which support it.
Sylwester removes ucast_shared field and the associated dead code related
to it.
Mikael removes non-inclusive language from the driver.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: remove non-inclusive language
ice: Remove ucast_shared
ice: Allow 100M speeds for some devices
ice: Implement FCS/CRC and VLAN stripping co-existence policy
ice: Implement control of FCS/CRC stripping
====================
Link: https://lore.kernel.org/r/20220818155207.996297-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The value is only ever set once in bond_3ad_initialize and only ever
read otherwise. There seems to be no reason to set the variable via
bond_3ad_initialize when setting the global variable will do. Change
ad_ticks_per_sec to a const to enforce its read-only usage.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is caused by the global variable ad_ticks_per_sec being zero as
demonstrated by the reproducer script discussed below. This causes
all timer values in __ad_timer_to_ticks to be zero, resulting
in the periodic timer to never fire.
To reproduce:
Run the script in
`tools/testing/selftests/drivers/net/bonding/bond-break-lacpdu-tx.sh` which
puts bonding into a state where it never transmits LACPDUs.
line 44: ip link add fbond type bond mode 4 miimon 200 \
xmit_hash_policy 1 ad_actor_sys_prio 65535 lacp_rate fast
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 48: ip link set fbond address 52:54:00:3B:7C:A6
setting bond MAC addr
call stack:
bond->dev->dev_addr = new_mac
line 52: ip link set fbond type bond ad_actor_sys_prio 65535
setting bond param: ad_actor_sys_prio
given:
params.ad_actor_system = 0
call stack:
bond_option_ad_actor_sys_prio()
-> bond_3ad_update_ad_actor_settings()
-> set ad.system.sys_priority = bond->params.ad_actor_sys_prio
-> ad.system.sys_mac_addr = bond->dev->dev_addr; because
params.ad_actor_system == 0
results:
ad.system.sys_mac_addr = bond->dev->dev_addr
line 60: ip link set veth1-bond down master fbond
given:
params.ad_actor_system = 0
params.mode = BOND_MODE_8023AD
ad.system.sys_mac_addr == bond->dev->dev_addr
call stack:
bond_enslave
-> bond_3ad_initialize(); because first slave
-> if ad.system.sys_mac_addr != bond->dev->dev_addr
return
results:
Nothing is run in bond_3ad_initialize() because dev_addr equals
sys_mac_addr leaving the global ad_ticks_per_sec zero as it is
never initialized anywhere else.
The if check around the contents of bond_3ad_initialize() is no longer
needed due to commit 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings
changes immediately") which sets ad.system.sys_mac_addr if any one of
the bonding parameters whos set function calls
bond_3ad_update_ad_actor_settings(). This is because if
ad.system.sys_mac_addr is zero it will be set to the current bond mac
address, this causes the if check to never be true.
Fixes: 5ee14e6d336f ("bonding: 3ad: apply ad_actor settings changes immediately")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since priv->rx_mapping[i] is maped in moxart_mac_open(), we
should unmap it from moxart_mac_stop(). Fixes 2 warnings.
1. During error unwinding in moxart_mac_probe(): "goto init_fail;",
then moxart_mac_free_memory() calls dma_unmap_single() with
priv->rx_mapping[i] pointers zeroed.
WARNING: CPU: 0 PID: 1 at kernel/dma/debug.c:963 check_unmap+0x704/0x980
DMA-API: moxart-ethernet 92000000.mac: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=1600 bytes]
CPU: 0 PID: 1 Comm: swapper Not tainted 5.19.0+ #60
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0xbc/0x1f0
__warn from warn_slowpath_fmt+0x94/0xc8
warn_slowpath_fmt from check_unmap+0x704/0x980
check_unmap from debug_dma_unmap_page+0x8c/0x9c
debug_dma_unmap_page from moxart_mac_free_memory+0x3c/0xa8
moxart_mac_free_memory from moxart_mac_probe+0x190/0x218
moxart_mac_probe from platform_probe+0x48/0x88
platform_probe from really_probe+0xc0/0x2e4
2. After commands:
ip link set dev eth0 down
ip link set dev eth0 up
WARNING: CPU: 0 PID: 55 at kernel/dma/debug.c:570 add_dma_entry+0x204/0x2ec
DMA-API: moxart-ethernet 92000000.mac: cacheline tracking EEXIST, overlapping mappings aren't supported
CPU: 0 PID: 55 Comm: ip Not tainted 5.19.0+ #57
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0xbc/0x1f0
__warn from warn_slowpath_fmt+0x94/0xc8
warn_slowpath_fmt from add_dma_entry+0x204/0x2ec
add_dma_entry from dma_map_page_attrs+0x110/0x328
dma_map_page_attrs from moxart_mac_open+0x134/0x320
moxart_mac_open from __dev_open+0x11c/0x1ec
__dev_open from __dev_change_flags+0x194/0x22c
__dev_change_flags from dev_change_flags+0x14/0x44
dev_change_flags from devinet_ioctl+0x6d4/0x93c
devinet_ioctl from inet_ioctl+0x1ac/0x25c
v1 -> v2:
Extraneous change removed.
Fixes: 6c821bd9edc9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220819110519.1230877-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For some MAC drivers, they set the mac_managed_pm to true in its
->ndo_open() callback. So before the mac_managed_pm is set to true,
we still want to leverage the mdio_bus_phy_suspend()/resume() for
the phy device suspend and resume. In this case, the phy device is
in PHY_READY, and we shouldn't warn about this. It also seems that
the check of mac_managed_pm in WARN_ON is redundant since we already
check this in the entry of mdio_bus_phy_resume(), so drop it.
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220819082451.1992102-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ipa_smem_init(), a Qualcomm SMEM region is allocated (if needed)
and then its virtual address is fetched using qcom_smem_get(). The
physical address associated with that region is also fetched.
The physical address is adjusted so that it is page-aligned, and an
attempt is made to update the size of the region to compensate for
any non-zero adjustment.
But that adjustment isn't done properly. The physical address is
aligned twice, and as a result the size is never actually adjusted.
Fix this by *not* aligning the "addr" local variable, and instead
making the "phys" local variable be the adjusted "addr" value.
Fixes: a0036bb413d5b ("net: ipa: define SMEM memory region for IPA")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220818134206.567618-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bdad4 ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unlock before returning if mlx5_device_enable_sriov() fails.
Fixes: 84a433a40d0e ("net/mlx5: Lock mlx5 devlink reload callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Call mlx5e_fs_vlan_free(fs) before kvfree(fs).
Fixes: af8bbf730068 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Use the list_for_each_entry_safe() macro to prevent dereferencing "obj"
after it has been freed.
Fixes: c4dfe704f53f ("net/mlx5e: kTLS, Recycle objects of device-offloaded TLS TX connections")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Unlock before returning on this error path.
Fixes: f1bc646c9a06 ("net/mlx5: Use devl_ API in mlx5_esw_offloads_devlink_port_register")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit reintroduced the ability to set hw-tc-offload
in switchdev mode by reusing NIC mode calls without modifying it
to support both modes, this can cause an illegal memory access
when trying to turn hw-tc-offload off.
Fix this by using the right TC_FLAG when checking if tc rules
are installed while disabling hw-tc-offload.
Fixes: d3cbd4254df8 ("net/mlx5e: Add ndo_set_feature for uplink representor")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There is a missing policer validation when offloading police action
with tc action api. Add it.
Fixes: 7d1a5ce46e47 ("net/mlx5e: TC, Support tc action api for police")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Driver caches packet merge type in mlx5e_params instance which must be
in perfect sync with the netdev_feature's bit.
Prior to this patch, in certain conditions (*) LRO state was set in
mlx5e_params, while netdev_feature's bit was off. Causing the LRO to
be applied on the RQs (HW level).
(*) This can happen only on profile init (mlx5e_build_nic_params()),
when RQ expect non-linear SKB and PCI is fast enough in comparison to
link width.
Solution: remove setting of packet merge type from
mlx5e_build_nic_params() as netdev features are not updated.
Fixes: 619a8f2a42f1 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add a lock_class_key per mlx5 device to avoid a false positive
"possible circular locking dependency" warning by lockdep, on flows
which lock more than one mlx5 device, such as adding SF.
kernel log:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc8+ #2 Not tainted
------------------------------------------------------
kworker/u20:0/8 is trying to acquire lock:
ffff88812dfe0d98 (&dev->intf_state_mutex){+.+.}-{3:3}, at: mlx5_init_one+0x2e/0x490 [mlx5_core]
but task is already holding lock:
ffff888101aa7898 (&(¬ifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(¬ifier->n_head)->rwsem){++++}-{3:3}:
down_write+0x90/0x150
blocking_notifier_chain_register+0x53/0xa0
mlx5_sf_table_init+0x369/0x4a0 [mlx5_core]
mlx5_init_one+0x261/0x490 [mlx5_core]
probe_one+0x430/0x680 [mlx5_core]
local_pci_probe+0xd6/0x170
work_for_cpu_fn+0x4e/0xa0
process_one_work+0x7c2/0x1340
worker_thread+0x6f6/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30
-> #0 (&dev->intf_state_mutex){+.+.}-{3:3}:
__lock_acquire+0x2fc7/0x6720
lock_acquire+0x1c1/0x550
__mutex_lock+0x12c/0x14b0
mlx5_init_one+0x2e/0x490 [mlx5_core]
mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core]
auxiliary_bus_probe+0x9d/0xe0
really_probe+0x1e0/0xaa0
__driver_probe_device+0x219/0x480
driver_probe_device+0x49/0x130
__device_attach_driver+0x1b8/0x280
bus_for_each_drv+0x123/0x1a0
__device_attach+0x1a3/0x460
bus_probe_device+0x1a2/0x260
device_add+0x9b1/0x1b40
__auxiliary_device_add+0x88/0xc0
mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core]
blocking_notifier_call_chain+0xd5/0x130
mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core]
process_one_work+0x7c2/0x1340
worker_thread+0x59d/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(¬ifier->n_head)->rwsem);
lock(&dev->intf_state_mutex);
lock(&(¬ifier->n_head)->rwsem);
lock(&dev->intf_state_mutex);
*** DEADLOCK ***
4 locks held by kworker/u20:0/8:
#0: ffff888150612938 ((wq_completion)mlx5_events){+.+.}-{0:0}, at: process_one_work+0x6e2/0x1340
#1: ffff888100cafdb8 ((work_completion)(&work->work)#3){+.+.}-{0:0}, at: process_one_work+0x70f/0x1340
#2: ffff888101aa7898 (&(¬ifier->n_head)->rwsem){++++}-{3:3}, at: blocking_notifier_call_chain+0x5a/0x130
#3: ffff88813682d0e8 (&dev->mutex){....}-{3:3}, at:__device_attach+0x76/0x460
stack backtrace:
CPU: 6 PID: 8 Comm: kworker/u20:0 Not tainted 5.19.0-rc8+
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_events mlx5_vhca_state_work_handler [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x7d
check_noncircular+0x278/0x300
? print_circular_bug+0x460/0x460
? lock_chain_count+0x20/0x20
? register_lock_class+0x1880/0x1880
__lock_acquire+0x2fc7/0x6720
? register_lock_class+0x1880/0x1880
? register_lock_class+0x1880/0x1880
lock_acquire+0x1c1/0x550
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
__mutex_lock+0x12c/0x14b0
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? mlx5_init_one+0x2e/0x490 [mlx5_core]
? _raw_read_unlock+0x1f/0x30
? mutex_lock_io_nested+0x1320/0x1320
? __ioremap_caller.constprop.0+0x306/0x490
? mlx5_sf_dev_probe+0x269/0x370 [mlx5_core]
? iounmap+0x160/0x160
mlx5_init_one+0x2e/0x490 [mlx5_core]
mlx5_sf_dev_probe+0x29c/0x370 [mlx5_core]
? mlx5_sf_dev_remove+0x130/0x130 [mlx5_core]
auxiliary_bus_probe+0x9d/0xe0
really_probe+0x1e0/0xaa0
__driver_probe_device+0x219/0x480
? auxiliary_match_id+0xe9/0x140
driver_probe_device+0x49/0x130
__device_attach_driver+0x1b8/0x280
? driver_allows_async_probing+0x140/0x140
bus_for_each_drv+0x123/0x1a0
? bus_for_each_dev+0x1a0/0x1a0
? lockdep_hardirqs_on_prepare+0x286/0x400
? trace_hardirqs_on+0x2d/0x100
__device_attach+0x1a3/0x460
? device_driver_attach+0x1e0/0x1e0
? kobject_uevent_env+0x22d/0xf10
bus_probe_device+0x1a2/0x260
device_add+0x9b1/0x1b40
? dev_set_name+0xab/0xe0
? __fw_devlink_link_to_suppliers+0x260/0x260
? memset+0x20/0x40
? lockdep_init_map_type+0x21a/0x7d0
__auxiliary_device_add+0x88/0xc0
? auxiliary_device_init+0x86/0xa0
mlx5_sf_dev_state_change_handler+0x67e/0x9d0 [mlx5_core]
blocking_notifier_call_chain+0xd5/0x130
mlx5_vhca_state_work_handler+0x2b0/0x3f0 [mlx5_core]
? mlx5_vhca_event_arm+0x100/0x100 [mlx5_core]
? lock_downgrade+0x6e0/0x6e0
? lockdep_hardirqs_on_prepare+0x286/0x400
process_one_work+0x7c2/0x1340
? lockdep_hardirqs_on_prepare+0x400/0x400
? pwq_dec_nr_in_flight+0x230/0x230
? rwlock_bug.part.0+0x90/0x90
worker_thread+0x59d/0xec0
? process_one_work+0x1340/0x1340
kthread+0x28f/0x330
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 6a3273217469 ("net/mlx5: SF, Port function state change support")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When the driver unloads, give/reclaim_pages may fail as PF driver in
teardown flow, current code will lead to the following kernel log print
'failed reclaiming pages: err 0'.
Fix it to get same behavior as before the cited commits,
by calling mlx5_cmd_check before handling error state.
mlx5_cmd_check will verify if the returned error is an actual error
needed to be handled by the driver or not and will return an
appropriate value.
Fixes: 8d564292a166 ("net/mlx5: Remove redundant error on reclaim pages")
Fixes: 4dac2f10ada0 ("net/mlx5: Remove redundant notify fail on give pages")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The lag_lock is taken from both process and softirq contexts which results
lockdep warning[0] about potential deadlock. However, just disabling
softirqs by using *_bh spinlock API is not enough since it will cause
warning in some contexts where the lock is obtained with hard irqs
disabled. To fix the issue save current irq state, disable them before
obtaining the lock an re-enable irqs from saved state after releasing it.
[0]:
[Sun Aug 7 13:12:29 2022] ================================
[Sun Aug 7 13:12:29 2022] WARNING: inconsistent lock state
[Sun Aug 7 13:12:29 2022] 5.19.0_for_upstream_debug_2022_08_04_16_06 #1 Not tainted
[Sun Aug 7 13:12:29 2022] --------------------------------
[Sun Aug 7 13:12:29 2022] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[Sun Aug 7 13:12:29 2022] swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[Sun Aug 7 13:12:29 2022] ffffffffa06dc0d8 (lag_lock){+.?.}-{2:2}, at: mlx5_lag_is_shared_fdb+0x1f/0x120 [mlx5_core]
[Sun Aug 7 13:12:29 2022] {SOFTIRQ-ON-W} state was registered at:
[Sun Aug 7 13:12:29 2022] lock_acquire+0x1c1/0x550
[Sun Aug 7 13:12:29 2022] _raw_spin_lock+0x2c/0x40
[Sun Aug 7 13:12:29 2022] mlx5_lag_add_netdev+0x13b/0x480 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5e_nic_enable+0x114/0x470 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5e_attach_netdev+0x30e/0x6a0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5e_resume+0x105/0x160 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5e_probe+0xac3/0x14f0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] auxiliary_bus_probe+0x9d/0xe0
[Sun Aug 7 13:12:29 2022] really_probe+0x1e0/0xaa0
[Sun Aug 7 13:12:29 2022] __driver_probe_device+0x219/0x480
[Sun Aug 7 13:12:29 2022] driver_probe_device+0x49/0x130
[Sun Aug 7 13:12:29 2022] __driver_attach+0x1e4/0x4d0
[Sun Aug 7 13:12:29 2022] bus_for_each_dev+0x11e/0x1a0
[Sun Aug 7 13:12:29 2022] bus_add_driver+0x3f4/0x5a0
[Sun Aug 7 13:12:29 2022] driver_register+0x20f/0x390
[Sun Aug 7 13:12:29 2022] __auxiliary_driver_register+0x14e/0x260
[Sun Aug 7 13:12:29 2022] mlx5e_init+0x38/0x90 [mlx5_core]
[Sun Aug 7 13:12:29 2022] vhost_iotlb_itree_augment_rotate+0xcb/0x180 [vhost_iotlb]
[Sun Aug 7 13:12:29 2022] do_one_initcall+0xc4/0x400
[Sun Aug 7 13:12:29 2022] do_init_module+0x18a/0x620
[Sun Aug 7 13:12:29 2022] load_module+0x563a/0x7040
[Sun Aug 7 13:12:29 2022] __do_sys_finit_module+0x122/0x1d0
[Sun Aug 7 13:12:29 2022] do_syscall_64+0x3d/0x90
[Sun Aug 7 13:12:29 2022] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[Sun Aug 7 13:12:29 2022] irq event stamp: 3596508
[Sun Aug 7 13:12:29 2022] hardirqs last enabled at (3596508): [<ffffffff813687c2>] __local_bh_enable_ip+0xa2/0x100
[Sun Aug 7 13:12:29 2022] hardirqs last disabled at (3596507): [<ffffffff813687da>] __local_bh_enable_ip+0xba/0x100
[Sun Aug 7 13:12:29 2022] softirqs last enabled at (3596488): [<ffffffff81368a2a>] irq_exit_rcu+0x11a/0x170
[Sun Aug 7 13:12:29 2022] softirqs last disabled at (3596495): [<ffffffff81368a2a>] irq_exit_rcu+0x11a/0x170
[Sun Aug 7 13:12:29 2022]
other info that might help us debug this:
[Sun Aug 7 13:12:29 2022] Possible unsafe locking scenario:
[Sun Aug 7 13:12:29 2022] CPU0
[Sun Aug 7 13:12:29 2022] ----
[Sun Aug 7 13:12:29 2022] lock(lag_lock);
[Sun Aug 7 13:12:29 2022] <Interrupt>
[Sun Aug 7 13:12:29 2022] lock(lag_lock);
[Sun Aug 7 13:12:29 2022]
*** DEADLOCK ***
[Sun Aug 7 13:12:29 2022] 4 locks held by swapper/0/0:
[Sun Aug 7 13:12:29 2022] #0: ffffffff84643260 (rcu_read_lock){....}-{1:2}, at: mlx5e_napi_poll+0x43/0x20a0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] #1: ffffffff84643260 (rcu_read_lock){....}-{1:2}, at: netif_receive_skb_list_internal+0x2d7/0xd60
[Sun Aug 7 13:12:29 2022] #2: ffff888144a18b58 (&br->hash_lock){+.-.}-{2:2}, at: br_fdb_update+0x301/0x570
[Sun Aug 7 13:12:29 2022] #3: ffffffff84643260 (rcu_read_lock){....}-{1:2}, at: atomic_notifier_call_chain+0x5/0x1d0
[Sun Aug 7 13:12:29 2022]
stack backtrace:
[Sun Aug 7 13:12:29 2022] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.19.0_for_upstream_debug_2022_08_04_16_06 #1
[Sun Aug 7 13:12:29 2022] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[Sun Aug 7 13:12:29 2022] Call Trace:
[Sun Aug 7 13:12:29 2022] <IRQ>
[Sun Aug 7 13:12:29 2022] dump_stack_lvl+0x57/0x7d
[Sun Aug 7 13:12:29 2022] mark_lock.part.0.cold+0x5f/0x92
[Sun Aug 7 13:12:29 2022] ? lock_chain_count+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? unwind_next_frame+0x1c4/0x1b50
[Sun Aug 7 13:12:29 2022] ? secondary_startup_64_no_verify+0xcd/0xdb
[Sun Aug 7 13:12:29 2022] ? mlx5e_napi_poll+0x4e9/0x20a0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? mlx5e_napi_poll+0x4e9/0x20a0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? stack_access_ok+0x1d0/0x1d0
[Sun Aug 7 13:12:29 2022] ? start_kernel+0x3a7/0x3c5
[Sun Aug 7 13:12:29 2022] __lock_acquire+0x1260/0x6720
[Sun Aug 7 13:12:29 2022] ? lock_chain_count+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? lock_chain_count+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? register_lock_class+0x1880/0x1880
[Sun Aug 7 13:12:29 2022] ? mark_lock.part.0+0xed/0x3060
[Sun Aug 7 13:12:29 2022] ? stack_trace_save+0x91/0xc0
[Sun Aug 7 13:12:29 2022] lock_acquire+0x1c1/0x550
[Sun Aug 7 13:12:29 2022] ? mlx5_lag_is_shared_fdb+0x1f/0x120 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? lockdep_hardirqs_on_prepare+0x400/0x400
[Sun Aug 7 13:12:29 2022] ? __lock_acquire+0xd6f/0x6720
[Sun Aug 7 13:12:29 2022] _raw_spin_lock+0x2c/0x40
[Sun Aug 7 13:12:29 2022] ? mlx5_lag_is_shared_fdb+0x1f/0x120 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5_lag_is_shared_fdb+0x1f/0x120 [mlx5_core]
[Sun Aug 7 13:12:29 2022] mlx5_esw_bridge_rep_vport_num_vhca_id_get+0x1a0/0x600 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? mlx5_esw_bridge_update_work+0x90/0x90 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? lock_acquire+0x1c1/0x550
[Sun Aug 7 13:12:29 2022] mlx5_esw_bridge_switchdev_event+0x185/0x8f0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? mlx5_esw_bridge_port_obj_attr_set+0x3e0/0x3e0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? check_chain_key+0x24a/0x580
[Sun Aug 7 13:12:29 2022] atomic_notifier_call_chain+0xd7/0x1d0
[Sun Aug 7 13:12:29 2022] br_switchdev_fdb_notify+0xea/0x100
[Sun Aug 7 13:12:29 2022] ? br_switchdev_set_port_flag+0x310/0x310
[Sun Aug 7 13:12:29 2022] fdb_notify+0x11b/0x150
[Sun Aug 7 13:12:29 2022] br_fdb_update+0x34c/0x570
[Sun Aug 7 13:12:29 2022] ? lock_chain_count+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? br_fdb_add_local+0x50/0x50
[Sun Aug 7 13:12:29 2022] ? br_allowed_ingress+0x5f/0x1070
[Sun Aug 7 13:12:29 2022] ? check_chain_key+0x24a/0x580
[Sun Aug 7 13:12:29 2022] br_handle_frame_finish+0x786/0x18e0
[Sun Aug 7 13:12:29 2022] ? check_chain_key+0x24a/0x580
[Sun Aug 7 13:12:29 2022] ? br_handle_local_finish+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? __lock_acquire+0xd6f/0x6720
[Sun Aug 7 13:12:29 2022] ? sctp_inet_bind_verify+0x4d/0x190
[Sun Aug 7 13:12:29 2022] ? xlog_unpack_data+0x2e0/0x310
[Sun Aug 7 13:12:29 2022] ? br_handle_local_finish+0x20/0x20
[Sun Aug 7 13:12:29 2022] br_nf_hook_thresh+0x227/0x380 [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? setup_pre_routing+0x460/0x460 [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? br_handle_local_finish+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? br_nf_pre_routing_ipv6+0x48b/0x69c [br_netfilter]
[Sun Aug 7 13:12:29 2022] br_nf_pre_routing_finish_ipv6+0x5c2/0xbf0 [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? br_handle_local_finish+0x20/0x20
[Sun Aug 7 13:12:29 2022] br_nf_pre_routing_ipv6+0x4c6/0x69c [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? br_validate_ipv6+0x9e0/0x9e0 [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? br_nf_forward_arp+0xb70/0xb70 [br_netfilter]
[Sun Aug 7 13:12:29 2022] ? br_nf_pre_routing+0xacf/0x1160 [br_netfilter]
[Sun Aug 7 13:12:29 2022] br_handle_frame+0x8a9/0x1270
[Sun Aug 7 13:12:29 2022] ? br_handle_frame_finish+0x18e0/0x18e0
[Sun Aug 7 13:12:29 2022] ? register_lock_class+0x1880/0x1880
[Sun Aug 7 13:12:29 2022] ? br_handle_local_finish+0x20/0x20
[Sun Aug 7 13:12:29 2022] ? bond_handle_frame+0xf9/0xac0 [bonding]
[Sun Aug 7 13:12:29 2022] ? br_handle_frame_finish+0x18e0/0x18e0
[Sun Aug 7 13:12:29 2022] __netif_receive_skb_core+0x7c0/0x2c70
[Sun Aug 7 13:12:29 2022] ? check_chain_key+0x24a/0x580
[Sun Aug 7 13:12:29 2022] ? generic_xdp_tx+0x5b0/0x5b0
[Sun Aug 7 13:12:29 2022] ? __lock_acquire+0xd6f/0x6720
[Sun Aug 7 13:12:29 2022] ? register_lock_class+0x1880/0x1880
[Sun Aug 7 13:12:29 2022] ? check_chain_key+0x24a/0x580
[Sun Aug 7 13:12:29 2022] __netif_receive_skb_list_core+0x2d7/0x8a0
[Sun Aug 7 13:12:29 2022] ? lock_acquire+0x1c1/0x550
[Sun Aug 7 13:12:29 2022] ? process_backlog+0x960/0x960
[Sun Aug 7 13:12:29 2022] ? lockdep_hardirqs_on_prepare+0x129/0x400
[Sun Aug 7 13:12:29 2022] ? kvm_clock_get_cycles+0x14/0x20
[Sun Aug 7 13:12:29 2022] netif_receive_skb_list_internal+0x5f4/0xd60
[Sun Aug 7 13:12:29 2022] ? do_xdp_generic+0x150/0x150
[Sun Aug 7 13:12:29 2022] ? mlx5e_poll_rx_cq+0xf6b/0x2960 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? mlx5e_poll_ico_cq+0x3d/0x1590 [mlx5_core]
[Sun Aug 7 13:12:29 2022] napi_complete_done+0x188/0x710
[Sun Aug 7 13:12:29 2022] mlx5e_napi_poll+0x4e9/0x20a0 [mlx5_core]
[Sun Aug 7 13:12:29 2022] ? __queue_work+0x53c/0xeb0
[Sun Aug 7 13:12:29 2022] __napi_poll+0x9f/0x540
[Sun Aug 7 13:12:29 2022] net_rx_action+0x420/0xb70
[Sun Aug 7 13:12:29 2022] ? napi_threaded_poll+0x470/0x470
[Sun Aug 7 13:12:29 2022] ? __common_interrupt+0x79/0x1a0
[Sun Aug 7 13:12:29 2022] __do_softirq+0x271/0x92c
[Sun Aug 7 13:12:29 2022] irq_exit_rcu+0x11a/0x170
[Sun Aug 7 13:12:29 2022] common_interrupt+0x7d/0xa0
[Sun Aug 7 13:12:29 2022] </IRQ>
[Sun Aug 7 13:12:29 2022] <TASK>
[Sun Aug 7 13:12:29 2022] asm_common_interrupt+0x22/0x40
[Sun Aug 7 13:12:29 2022] RIP: 0010:default_idle+0x42/0x60
[Sun Aug 7 13:12:29 2022] Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 6b f1 22 02 85 c0 7e 07 0f 00 2d 80 3b 4a 00 fb f4 <c3> 48 c7 c7 e0 07 7e 85 e8 21 bd 40 fe eb de 66 66 2e 0f 1f 84 00
[Sun Aug 7 13:12:29 2022] RSP: 0018:ffffffff84407e18 EFLAGS: 00000242
[Sun Aug 7 13:12:29 2022] RAX: 0000000000000001 RBX: ffffffff84ec4a68 RCX: 1ffffffff0afc0fc
[Sun Aug 7 13:12:29 2022] RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffff835b1fac
[Sun Aug 7 13:12:29 2022] RBP: 0000000000000000 R08: 0000000000000001 R09: ffff8884d2c44ac3
[Sun Aug 7 13:12:29 2022] R10: ffffed109a588958 R11: 00000000ffffffff R12: 0000000000000000
[Sun Aug 7 13:12:29 2022] R13: ffffffff84efac20 R14: 0000000000000000 R15: dffffc0000000000
[Sun Aug 7 13:12:29 2022] ? default_idle_call+0xcc/0x460
[Sun Aug 7 13:12:29 2022] default_idle_call+0xec/0x460
[Sun Aug 7 13:12:29 2022] do_idle+0x394/0x450
[Sun Aug 7 13:12:29 2022] ? arch_cpu_idle_exit+0x40/0x40
[Sun Aug 7 13:12:29 2022] cpu_startup_entry+0x19/0x20
[Sun Aug 7 13:12:29 2022] rest_init+0x156/0x250
[Sun Aug 7 13:12:29 2022] arch_call_rest_init+0xf/0x15
[Sun Aug 7 13:12:29 2022] start_kernel+0x3a7/0x3c5
[Sun Aug 7 13:12:29 2022] secondary_startup_64_no_verify+0xcd/0xdb
[Sun Aug 7 13:12:29 2022] </TASK>
Fixes: ff9b7521468b ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Make sure to modify the rule for uplink forwarding only for the case
where destination vport number is MLX5_VPORT_UPLINK.
Fixes: 94db33177819 ("net/mlx5: Support multiport eswitch mode")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Only set MLX5_LAG_FLAG_NDEVS_READY if both netdevices are registered.
Doing so guarantees that both ldev->pf[MLX5_LAG_P0].dev and
ldev->pf[MLX5_LAG_P1].dev have valid pointers when
MLX5_LAG_FLAG_NDEVS_READY is set.
The core issue is asymmetry in setting MLX5_LAG_FLAG_NDEVS_READY and
clearing it. Setting it is done wrongly when both
ldev->pf[MLX5_LAG_P0].dev and ldev->pf[MLX5_LAG_P1].dev are set;
clearing it is done right when either of ldev->pf[i].netdev is cleared.
Consider the following scenario:
1. PF0 loads and sets ldev->pf[MLX5_LAG_P0].dev to a valid pointer
2. PF1 loads and sets both ldev->pf[MLX5_LAG_P1].dev and
ldev->pf[MLX5_LAG_P1].netdev with valid pointers. This results in
MLX5_LAG_FLAG_NDEVS_READY is set.
3. PF0 is unloaded before setting dev->pf[MLX5_LAG_P0].netdev.
MLX5_LAG_FLAG_NDEVS_READY remains set.
Further execution of mlx5_do_bond() will result in null pointer
dereference when calling mlx5_lag_is_multipath()
This patch fixes the following call trace actually encountered:
[ 1293.475195] BUG: kernel NULL pointer dereference, address: 00000000000009a8
[ 1293.478756] #PF: supervisor read access in kernel mode
[ 1293.481320] #PF: error_code(0x0000) - not-present page
[ 1293.483686] PGD 0 P4D 0
[ 1293.484434] Oops: 0000 [#1] SMP PTI
[ 1293.485377] CPU: 1 PID: 23690 Comm: kworker/u16:2 Not tainted 5.18.0-rc5_for_upstream_min_debug_2022_05_05_10_13 #1
[ 1293.488039] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 1293.490836] Workqueue: mlx5_lag mlx5_do_bond_work [mlx5_core]
[ 1293.492448] RIP: 0010:mlx5_lag_is_multipath+0x5/0x50 [mlx5_core]
[ 1293.494044] Code: e8 70 40 ff e0 48 8b 14 24 48 83 05 5c 1a 1b 00 01 e9 19 ff ff ff 48 83 05 47 1a 1b 00 01 eb d7 0f 1f 44 00 00 0f 1f 44 00 00 <48> 8b 87 a8 09 00 00 48 85 c0 74 26 48 83 05 a7 1b 1b 00 01 41 b8
[ 1293.498673] RSP: 0018:ffff88811b2fbe40 EFLAGS: 00010202
[ 1293.500152] RAX: ffff88818a94e1c0 RBX: ffff888165eca6c0 RCX: 0000000000000000
[ 1293.501841] RDX: 0000000000000001 RSI: ffff88818a94e1c0 RDI: 0000000000000000
[ 1293.503585] RBP: 0000000000000000 R08: ffff888119886740 R09: ffff888165eca73c
[ 1293.505286] R10: 0000000000000018 R11: 0000000000000018 R12: ffff88818a94e1c0
[ 1293.506979] R13: ffff888112729800 R14: 0000000000000000 R15: ffff888112729858
[ 1293.508753] FS: 0000000000000000(0000) GS:ffff88852cc40000(0000) knlGS:0000000000000000
[ 1293.510782] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1293.512265] CR2: 00000000000009a8 CR3: 00000001032d4002 CR4: 0000000000370ea0
[ 1293.514001] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1293.515806] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fixes: 8a66e4585979 ("net/mlx5: Change ownership model for lag")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When querying mlx5 non-uplink representors capabilities with ethtool
rx-vlan-offload is marked as "off [fixed]". However, it is actually always
enabled because mlx5e_params->vlan_strip_disable is 0 by default when
initializing struct mlx5e_params instance. Fix the issue by explicitly
setting the vlan_strip_disable to 'true' for non-uplink representors.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
Vadim Pasternak
Vikas Gupta
Pavan Chebbi
Sergei Antonov
Vladimir Oltean
Maciej Żenczykowski
Saravana Kannan
Jilin Yuan
Lin Ma
Roi Dayan
Jianbo Liu
Lama Kayal
Jakub Kicinski
Jonathan Toppins
Xiaolei Wang
Alex Elder
Dan Carpenter
Maor Dickman
Aya Levin
Moshe Shemesh
Roy Novich
Vlad Buslov
Eli Cohen