| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
.dellink does not get called after .newlink fails,
bareudp_newlink() must undo what bareudp_configure()
has done if bareudp_link_config() fails.
v2: call bareudp_dellink(), like bareudp_dev_create() does
Fixes: 571912c69f0e ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Link: https://lore.kernel.org/r/20210105190725.1736246-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The error message says that "Jumbo frames are not supported on XDP", but
the code checks for mtu > MVNETA_MAX_RX_BUF_SIZE, not mtu > 1500.
Fix this error message.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 0db51da7a8e9 ("net: mvneta: add basic XDP support")
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20210105172333.21613-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX). SCU driver manages the IPC interface
between host CPU and the SCU firmware running on M4.
For i.MX8QM, stop mode request is controlled by System Controller Unit(SCU)
firmware, this patch introduces FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW quirk
for this function.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-6-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds back support for half-duplex controllers, which was removed in
the last patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-17-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch reworks the SPI access and fixes several probems:
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Do not place variable "addr" on stack and use it as buffer for SPI
transfer. Buffers for SPI transfers must be allocated from DMA save
memory.
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Halfe number of SPI transfers by using a single buffer + memcpy().
This improves the performance, especially on SPI controllers, which
use interrupt based transfers.
- Use "8" bits per word, not "32". This makes it possible to use this
driver on SoCs like the Raspberry Pi, which SPI host controller
drivers only support 8 bits per word.
Note: this breaks half duplex only controllers. Support for them will be
re-added in the next patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-16-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The memory space of the chip is not fully populated, so add a regmap range
table to document this.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The tcan4x5x chip support bulk read/write, but as the length field is only 8
bits wide, the maximum is 256. A length of 0 is treated as 256.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch sets the regmap stide to 4, as the chip only supports access on 32
bit alligned access.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the max register value for the regmap.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces the context pointer of the regmap callback functions by a
pointer to the spi_device. This saves one level of indirection in the
callbacks.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch simplifies the tcan4x5x_regmap_write(0 function by removing not
needed casts and replaces hardcoded "4" by appropriate sizeof()s.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames the regmap_spi_gather_write() function to
tcan4x5x_regmap_gather_write(). Now it has a "tcan4x5x_" prefix as all other
functions in this driver.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver doesn't use regmap async support, so remove the stubs.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With C99 initializers, all non mentioned members are initialzied to 0, so
remove not needed initialization of read_flag_mask.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch marks the struct regmap_bus tcan4x5x_bus as constant.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the regmap code into a seperate file.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch to move the regmap related code into a seperate
file. This patch removes the tcan4x5x.c to tcan4x5x-core.c.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch beautifies the indention of the tcan4x5x_of_match and
tcan4x5x_id_table.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch replaces the DEVICE_NAME macro by KBUILD_MODNAME and removed the
superfluous DEVICE_NAME.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, except the PHY ID Low/High registers are swapped.
Register MDIO bus so this PHY can be detected and probed by phylib.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 1d6cd3929360 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because macvlan_common_newlink() and macvlan_changelink() already
checked NULL data parameter, so the additional check is unnecessary,
just remove it.
Fixes: 79cf79abce71 ("macvlan: add source mode")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.
Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d142 ("net: hns3: add phy selftest function")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware supports 8 RSS groups per interface. Currently we are using
only group '0'. This patch allows user to create new RSS groups/contexts
and use the same as destination for flow steering rules.
usage:
To steer the traffic to RQ 2,3
ethtool -X eth0 weight 0 0 1 1 context new
(It will print the allocated context id number)
New RSS context is 1
ethtool -N eth0 flow-type tcp4 dst-port 80 context 1 loc 1
To delete the context
ethtool -X eth0 context 1 delete
When an RSS context is removed, the active classification
rules using this context are also removed.
Change-log:
v4
- Fixed compiletime warning.
- Address Saeed's comments on v3.
v3
- Coverted otx2_set_rxfh() to use new function.
v2
- Removed unrelated whitespace
- Coverted otx2_get_rxfh() to use new function.
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A call to dma_alloc_coherent() is wrapped by sonic_alloc_descriptors().
This is correctly freed in the remove function, but not in the error
handling path of the probe function. Fix this by adding the missing
dma_free_coherent() call.
While at it, rename a label in order to be slightly more informative.
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
References: commit 10e3cc180e64 ("net/sonic: Fix a resource leak in an error handling path in 'jazz_sonic_probe()'")
Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085c5 ("Maxim/driver: Add driver for maxim ds26522")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a9706503f ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this, the driver fails to link:
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_grc_dump':
qed_debug.c:(.text+0x4068): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_idle_chk_dump':
qed_debug.c:(.text+0x51fc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_mcp_trace_dump':
qed_debug.c:(.text+0x6000): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_dbg_reg_fifo_dump':
qed_debug.c:(.text+0x66cc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o:qed_debug.c:(.text+0x6aa4): more undefined references to `crc32_le' follow
Fixes: 7a4b21b7d1f0 ("qed: Add nvram selftest")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
mlx5-updates-2021-01-05
SW steering, Refactor to have a device specific STE layer below dr_ste
This series introduces some improvements and refactoring by adding a new layer
below dr_ste to allow support for different devices format.
It adds a struct of device specific callbacks for STE layer below dr_ste.
Each device will implement its HW-specific function, and a common logic
from the DR code will access these functions through the new ste_ctx API.
Connect-X5-style steering format is called STE_v0.
In the next patch series we bring the Connect-X6-style format - STE_v1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The simple_strtol() function is deprecated, use simple_strtoul() instead.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MHI net is protocol agnostic, the payload protocol depends on the modem
configuration, which can be either RMNET (IP muxing and aggregation) or
raw IP. This patch adds support for incomming IPv4/IPv6 packets, that
was previously unconditionnaly reported as RMNET packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Jakub Kicinski
Marek Behún
Joakim Zhang
Marc Kleine-Budde
Marek Vasut
Michael Ellerman
Yunjian Wang
Jouni K. Seppänen
Jian Shen
Yufeng Mo
Yonglong Liu
Geetha sowjanya
Samuel Holland
Zheng Yongjun
Christophe JAILLET
Arnd Bergmann
David S. Miller
Loic Poulain