aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2020-07-15rtw88: single rf path chips don't support TX STBCTzu-En Huang1-2/+2
Since single rf path chips don't support TX SPBC, tell mac80211 to not advertise it. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add beamformee supportTzu-En Huang2-2/+48
Beamforming is used for directional signal transmission/reception. Beamformee plays the role for signal reception, and makes the RX performance better in middle distance range. Implement beamformee related callbacks for 8821c. Since 8821c only support 1ss rate, nc_index in beamformee setting needs to be adjusted based on the capability. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add power trackingTzu-En Huang3-0/+293
The TX power requires to be adjusted based on the thermal value. The actual power will decrease if the thermal value raised, and will increase if the thermal value lowered. Driver comapres the thermal value, as moving averages. If it changes over a limit, driver will modify the TX power index to compensate. Implement rtw_chip_ops::pwr_track() for 8821c. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add cck pd settingsTzu-En Huang3-0/+29
CCK PD can reduce the number of false alarm of the CCK rates. It dynamically adjusts the power threshold and CS ratio. The values are compared to the values of the previous level, if the level is changed, set new values of power threshold and CS ratio. Implement rtw_chip_ops::cck_pd_set() for 8821c. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add phy calibrationTzu-En Huang1-0/+34
In order to get a better TX EVM, do calibration after association. The calibration needed for 8821c is the IQK, which is done in the firmware. Implement the rtw_chip_ops::phy_calibration() to trigger firmware to calibrate. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-8-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add false alarm statisticsTzu-En Huang2-0/+63
False alarm statistics can be used to adjust the RX gain. This helps the driver to adapt to different circumstances. Implement rtw_chip_ops::false_alarm_statistics() for 8821c. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-7-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add query rx desc supportTzu-En Huang2-0/+117
Some RX packets contain also information about environment status. Implement rtw_chip_ops::query_rx_desc() for 8821c. Parse the RX descriptor which describes the current condition of the received packet. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-6-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add set channel supportTzu-En Huang4-0/+229
8821c is capable of 2.4G and 5G. Implement rtw_chip_ops::set_channel() to set 2G and 5G channels. This includes MAC, BB and RF related settings. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add dig related settingsTzu-En Huang1-0/+6
To improve user experience in field, we need DIG to adjust RX initial gain depends on field situation. Define the register addresses for 8821c. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-4-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add set tx power indexTzu-En Huang1-0/+39
To configure the transmit power of 8821c implement trasmit power index setting callback function for 8821c. This is very similar to the callback function of 8822b. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-3-yhchuang@realtek.com
2020-07-15rtw88: 8821c: add basic functionsTzu-En Huang8-0/+7514
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips. This patch adds the basic functions such as parameter tables, chip information, power on flow. Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
2020-07-14qlcnic: convert to new udp_tunnel_nic infraJakub Kicinski3-70/+32
Straightforward conversion to new infra, 1 VxLAN port, handler may sleep. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14qede: convert to new udp_tunnel_nic infraJakub Kicinski3-103/+58
Covert to new infra. Looks like this driver was not doing ref counting, and sleeping in the callback. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14fm10k: convert to new udp_tunnel_nic infraJakub Kicinski4-159/+28
Straightforward conversion to new infra. Driver restores info after close/open cycle by calling its internal restore function so just use that, no need for udp_tunnel_nic_reset_ntf() here. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14liquidio_vf: convert to new udp_tunnel_nic infraJakub Kicinski1-26/+33
Carbon copy of the previous change. This driver is just a super thin FW interface, but Derek let us know the table has 1024 entries. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14liquidio: convert to new udp_tunnel_nic infraJakub Kicinski1-26/+33
This driver is just a super thin FW interface, but Derek let us know the table has 1024 entries. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14enic: convert to new udp_tunnel_nic infraJakub Kicinski1-66/+39
Convert to new infra, now the refcounting will be correct, and driver gets port replay of other ports when offloaded port gets removed. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14cxgb4: convert to new udp_tunnel_nic infraJakub Kicinski2-79/+31
Convert to new infra, this driver is very simple. The check of adapter->rawf_cnt in cxgb_udp_tunnel_unset_port() is kept from the old port deletion function but it's dodgy since nothing ever updates that member once its set during init. Also .set_port callback always adds the raw mac filter.. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14bnx2x: convert to new udp_tunnel_nic infraJakub Kicinski3-123/+29
Fairly straightforward conversion - no need to keep track of the use count, and replay when ports get removed, also callbacks can just sleep. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14xgbe: convert to new udp_tunnel_nic infraJakub Kicinski3-243/+30
Make use of the new udp_tunnel_nic infra. Don't clear the features when VxLAN port is not present to make all drivers behave the same. Driver will now (until we address the problem in the core) leave the RX UDP tunnel feature always on, since this is what most drivers do. Remove the list of VxLAN ports, just program the one core told us to. The driver seem to want to clear the VxLAN ports on close but it doesn't seem to flush the port list properly so it'd get wrong use counts after close/open. Again since it calls its own open handler we need the reset notification hack. v2: - fix kbuild warning Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14xgbe: switch to more generic VxLAN detectionJakub Kicinski1-19/+8
Instead of looping though the list of ports just check if the geometry of the packet is correct for VxLAN. HW most likely doesn't care about the exact port, anyway, since only first port is actually offloaded, and this way we won't have to maintain the port list at all. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14be2net: convert to new udp_tunnel_nic infraJakub Kicinski2-165/+38
Convert be2net to new udp_tunnel_nic infra. NIC only takes one VxLAN port. Remove the port tracking using a list. The warning in be_work_del_vxlan_port() looked suspicious - like the driver expected ports to be removed in order of addition. be2net unregisters ports when going down and re-registers them (for skyhawk) when coming up, but it never checks if the device is up in the add_port / del_port callbacks. Make it use UDP_TUNNEL_NIC_INFO_OPEN_ONLY. Sadly this driver calls its own open/close functions directly so the udp_tunnel_nic_reset_ntf() workaround is needed. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14nfp: convert to new udp_tunnel_nic infraJakub Kicinski2-97/+34
NFP conversion is pretty straightforward. We want to be able to sleep, and only get callbacks when the device is open. NFP did not ask for port replay when ports were removed, now new infra will provide this feature for free. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14qed: Disable "MFW indication via attention" SPAM every 5 minutesLaurence Oberman1-1/+2
This is likely firmware causing this but its starting to annoy customers. Change the message level to verbose to prevent the spam. Note that this seems to only show up with ISCSI enabled on the HBA via the qedi driver. Signed-off-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14ksz884x: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-38/+30
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'ksz_alloc_desc()', GFP_KERNEL can be used because a few lines below, GFP_KERNEL is also used in the 'ksz_alloc_soft_desc()' calls. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14r8169: add support for RTL8125BHeiner Kallweit3-23/+141
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well w/o firmware, however for a stable link at 1Gbps firmware revision 0.0.2 is needed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14net: phy: realtek: add support for RTL8125B-internal PHYHeiner Kallweit1-0/+12
Realtek assigned a new PHY ID for the RTL8125B-internal PHY. It's however compatible with the RTL8125A-internal PHY. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: core: Use mirror reason during Rx listener lookupIdo Schimmel2-2/+5
The Rx listener abstraction allows the switch driver (e.g., mlxsw_spectrum) to register a function that is called when a packet is received (trapped) for a specific reason. Up until now, the Rx listener lookup was solely based on the trap identifier. However, when a packet is mirrored to the CPU the trap identifier merely indicates that the packet was mirrored, but not why it was mirrored. This makes it impossible for the switch driver to register different Rx listeners for different mirror reasons. Solve this by allowing the switch driver to register a Rx listener with a mirror reason and by extending the Rx listener lookup to take the mirror reason into account. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: pci: Retrieve mirror reason from CQE during receiveIdo Schimmel2-1/+6
In case the mirror reason is valid, retrieve it into the Rx information so that it could be used during listener lookup in a later patch. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: pci: Add mirror reason field to CQEv2Ido Schimmel1-0/+5
The Completion Queue Element version 2 (CQEv2) includes a field called 'mirror_reason' which indicates why the packet was mirrored to the CPU. Add the field so that it can be used by a later patch. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: trap: Add trap identifiers for mirrored packetsIdo Schimmel1-0/+8
Packets that are mirrored to the CPU port are trapped with one of eight trap identifiers. Add them. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: reg: Increase trap identifier to 10 bitsAmit Cohen3-3/+3
The trap identifier was increased to 10 bits in new versions of the Programmer's Reference Manual (PRM). Increase it accordingly in the Host PacKet Trap (HPKT) register and in the Completion Queue Element (CQE). This is significant for subsequent patches that will introduce trap identifiers which utilize the extended range. Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Allow setting policer on a SPAN agentIdo Schimmel4-3/+114
When mirroring packets to the CPU port the mirrored packets are trapped to the CPU. However, unlike other traps, it is not possible to set a policer on the associated trap group. Instead, the policer needs to be set on the SPAN agent. Moreover, the policer ID must be within a specified range: From a configurable (even) base ID to this base plus the maximum number of SPAN agents. While the immediate use case is to set the policer on a SPAN agent that mirrors to the CPU port, a policer can be set on any SPAN agent. Therefore, the operation is implemented for all SPAN agent types. Extend the SPAN agent request API to allow passing the desired policer ID that should be bound to the SPAN agent. Return an error for Spectrum-1, as it does not support policer setting on a SPAN agent. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Allow passing parameters to SPAN agentsIdo Schimmel5-8/+20
Currently, the only parameter of a SPAN agent is the netdev which the SPAN agent should mirror to. The next patch will add the ability to request a SPAN agent that mirrors to a specific netdev and has a specific policer ID bound to it. This is required when mirroring packets to the CPU port. Therefore, encapsulate the sole parameter to mlxsw_sp_span_agent_get() in a structure, so that it could later be extended with policer information. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Add support for mirroring towards CPU portIdo Schimmel1-0/+88
The Spectrum-2 and Spectrum-3 ASICs are able to mirror packets towards the CPU. These packets are then trapped like any other packet, but with a special packet trap and additional metadata such as why the packet was mirrored. The ability to mirror packets towards the CPU will be utilized by a subsequent patch set that will mirror packets that were dropped by the ASIC for various buffer-related reasons, such as tail-drop and early-drop. Add mirroring towards the CPU as a new SPAN agent type and re-use the functions that mirror to a physical port where possible. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Do not dereference destination netdevIdo Schimmel1-4/+3
Currently, the destination netdev to which we mirror must be a valid netdev. However, this is going to change with the introduction of mirroring towards the CPU port, as the CPU port does not have a backing netdev. Avoid dereferencing the destination netdev when it is not clear if it is valid or not. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Add driver private info to parms_set() callbackIdo Schimmel2-8/+14
The parms_set() callback is supposed to fill in the parameters for the SPAN agent, such as the destination port and encapsulation info, if any. When mirroring to the CPU port we cannot resolve the destination port (the CPU port) without access to the driver private info. Pass the driver private info to parms_set() callback so that it could be used later on to resolve the CPU port. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: spectrum_span: Add per-ASIC SPAN agent operationsIdo Schimmel1-4/+27
The various SPAN agent types differ in their mirror targets (i.e., physical port netdev vs. VLAN netdev) and the encapsulation headers that they need to encapsulate the mirrored packets with. The Spectrum-2 and Spectrum-3 ASICs support a SPAN agent type that is able to mirror towards the CPU, whereas the Spectrum-1 ASIC does not. Prepare for the addition of this new SPAN agent type by splitting the SPAN agent operations to be per-ASIC. Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: reg: add mirroring_pid_base to MOGCR registerAmit Cohen1-0/+8
Allow setting mirroring_pid_base using MOGCR register. Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14mlxsw: reg: Add session_id and pid to MPAT registerAmit Cohen1-0/+19
Allow setting session_id and pid as part of port analyzer configurations. Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14gianfar: Use random MAC address when none is givenMaxim Kochetkov1-1/+5
If there is no valid MAC address in the device tree, use a random MAC address. Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14hippi: Fix a size used in a 'pci_free_consistent()' in an error handling pathChristophe JAILLET1-1/+1
The size used when calling 'pci_alloc_consistent()' and 'pci_free_consistent()' should match. Fix it and have it consistent with the corresponding call in 'rr_close()'. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14net: neterion: vxge: switch from 'pci_' to 'dma_' APIChristophe JAILLET2-54/+52
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below. No GFP_ flag needs to be corrected. It has been compile tested. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14net: neterion: s2io: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-101/+90
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GPF_ with a correct flag. It has been compile tested. When memory is allocated in 'init_shared_mem()' GFP_KERNEL can be used because this flag is already used to allocate some memory in this function. While at it, update some debug message to match the new function names. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14lan743x: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-24/+22
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GPF_ with a correct flag. It has been compile tested. When memory is allocated in 'lan743x_tx_ring_cleanup()' and 'lan743x_rx_ring_init()', GFP_KERNEL can be used because this flag is already used to allocate some memory in these functions. While at it, remove a useless (void *) casting in the first hunk in so that the code is more consistent. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14wilc1000: let wilc_mac_xmit() return NETDEV_TX_OKLuc Van Oostenryck1-3/+3
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type defining 'NETDEV_TX_OK' but this driver returns '0' instead of 'NETDEV_TX_OK'. Fix this by returning 'NETDEV_TX_OK' instead of '0'. Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200629104009.84077-1-luc.vanoostenryck@gmail.com
2020-07-14wilc1000: use API version number info along with firmware filenameAjay Singh2-5/+14
Added version number info along with firmware name so driver can pick the correct revision of FW file. Moved FW filename macro as part of driver code & added MODULE_FIRMWARE to specify FW needed by module. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200710051826.3267-6-ajay.kathat@microchip.com
2020-07-14wilc1000: use unified single wilc1000 FW binaryAjay Singh2-13/+8
Modify WILC1000 binary filename to use single unified wilc1000 FW. A single wilc1000 binary is used for different wilc1000 revisions. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200710051826.3267-5-ajay.kathat@microchip.com
2020-07-14wilc1000: fix compiler warning for 'wowlan_support' unused variableAjay Singh1-0/+2
Avoid below reported warning found when 'CONFIG_PM' config is undefined. 'warning: unused variable 'wowlan_support' [-Wunused-const-variable]' Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200710051826.3267-4-ajay.kathat@microchip.com
2020-07-14wilc1000: use strlcpy to avoid 'stringop-truncation' warningAjay Singh1-2/+1
Make use 'strlcpy' instead of 'strncpy' to overcome 'stringop-truncation' compiler warning. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200710051826.3267-3-ajay.kathat@microchip.com
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.