| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Don't populate the array modes on the stack but instead make it
static const. Makes the object code smaller by 303 bytes.
Before:
text data bss dec hex filename
51240 5008 1312 57560 e0d8 mellanox/mlx4/en_ethtool.o
After:
text data bss dec hex filename
50937 5008 1312 57257 dfa9 mellanox/mlx4/en_ethtool.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue")
adds a } without corresponding { causing build break.
Fixes: 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add I40E_DEV_ID_10G_BASE_T_BC to i40e_pci_tbl
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add IP generic TX checksum offload functionality.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d932173 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.
More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.
Fixes: f3213d932173 ("ixgbe: Update driver to make use of DMA attributes in Rx path")
Signed-off-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit
'5098850c9b9b ("i40e/i40evf: i40e_register.h updates")'
it is no longer possible to trigger an EMP Reset from debugfs, but it's
possible to request it either way, to end up with a bad reset request:
echo empr > /sys/kernel/debug/i40e/0002\:01\:00.1/command
i40e 0002:01:00.1: debugfs: forcing EMPR
i40e 0002:01:00.1: bad reset request 0x00010000
So let's remove this piece of code and show the available valid commands
as it is when any invalid command is issued.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are several uses of hw_dbg in the code, producing no output. This
patch implements it using dev_debug.
Initially the intention was to implement it using netdev_dbg, analogously
to what is done in ixgbe for instance. That approach was avoided due to
some early usages of hw_dbg, like i40e_pf_reset, before the VSI structure
initialization causing NULL pointer dereference during the driver probe if
the debug messages were turned on as soon as the module is probed.
v2:
- Use dev_dbg instead of pr_debug, and take advantage of dev_name
instead of crafting pretty much the same device name locally as suggested
by Jakub Kicinski.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The mentioned function references a i40e_hw attribute, as parameter for
hw_dbg, but it doesn't exist in the function scope.
Fixes it by changing parameters from i40e_hmc_info to i40e_hw which can
retrieve the necessary i40e_hmc_info.
v2:
- Fixed reverse xmas tree code style issue as suggested by Jakub Kicinski
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PCIe device control 2 defines does not use internally.
This patch comes to clean up those.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Allow the VF to override the "permanent" MAC address set by the host.
This allows bonding to work in the case where the administrator has set
the VF MAC.
Note that the VF must still be set to Trusted on the host if this change
is to be accepted by the PF driver.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add NVM checksum validation during probe functionality.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the function fm10k_xmit_frame_ring, we recently switched to using
the skb_frag_size accessor instead of directly using the size member of
the skb fragment.
This made the for loop slightly harder to read because it created a very
long line that is difficult to split up. Avoid this by using a local
variable in the for loop, so that we do not have to break the line on an
open parenthesis.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Move igc_phy_setup_autoneg, igc_wait_autoneg and igc_set_fc_watermarks
up to avoid forward declaration.
It is not necessary to forward declare these static methods.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the
MII_BMSR may report 10Mbps, renders the network rather slow.
The issue has much lower fail rate after commit 59653e6497d1 ("e1000e:
Make watchdog use delayed work"), which essentially introduces some
delay before running the watchdog task.
But there's still a chance that the hot plugging event and the queued
watchdog task gets run at the same time, then the original issue can be
observed once again.
So let's use mod_delayed_work() to add a deterministic 1 second delay
before running watchdog task, after an interrupt.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixed issue in VM which shows no link when hypervisor is
restored from low-power state. The driver is responsible for re-enabling
any features of the device that had been disabled during suspend calls,
such as IRQs and bus mastering.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is no caller of function iavf_debug_d() in tree since
commit 75051ce4c5d8 ("iavf: Fix up debug print macro"),
so it can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Flower control message replies are handled in different locations. The truly
high priority replies are handled in the BH (tasklet) context, while the
remaining replies are handled in a predefined Linux work queue. The work
queue handler orders replies into high and low priority groups, and always
start servicing the high priority replies within the received batch first.
Reply Type: Rtnl Lock: Handler:
CMSG_TYPE_PORT_MOD no BH tasklet (mtu)
CMSG_TYPE_TUN_NEIGH no BH tasklet
CMSG_TYPE_FLOW_STATS no BH tasklet
CMSG_TYPE_PORT_REIFY no WQ high
CMSG_TYPE_PORT_MOD yes WQ high (link/mtu)
CMSG_TYPE_MERGE_HINT yes WQ low
CMSG_TYPE_NO_NEIGH no WQ low
CMSG_TYPE_ACTIVE_TUNS no WQ low
CMSG_TYPE_QOS_STATS no WQ low
CMSG_TYPE_LAG_CONFIG no WQ low
A subset of control messages can block waiting for an rtnl lock (from both
work queue priority groups). The rtnl lock is heavily contended for by
external processes such as systemd-udevd, systemd-network and libvirtd,
especially during netdev creation, such as when flower VFs and representors
are instantiated.
Kernel netlink instrumentation shows that external processes (such as
systemd-udevd) often use successive rtnl_trylock() sequences, which can result
in an rtnl_lock() blocked control message to starve for longer periods of time
during rtnl lock contention, i.e. netdev creation.
In the current design a single blocked control message will block the entire
work queue (both priorities), and introduce a latency which is
nondeterministic and dependent on system wide rtnl lock usage.
In some extreme cases, one blocked control message at exactly the wrong time,
just before the maximum number of VFs are instantiated, can block the work
queue for long enough to prevent VF representor REIFY replies from getting
handled in time for the 40ms timeout.
The firmware will deliver the total maximum number of REIFY message replies in
around 300us.
Only REIFY and MTU update messages require replies within a timeout period (of
40ms). The MTU-only updates are already done directly in the BH (tasklet)
handler.
Move the REIFY handler down into the BH (tasklet) in order to resolve timeouts
caused by a blocked work queue waiting on rtnl locks.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the array spec_opcode on the stack but instead make it
static const. Makes the object code smaller by 48 bytes.
Before:
text data bss dec hex filename
6914 1040 128 8082 1f92 hns3/hns3vf/hclgevf_cmd.o
After:
text data bss dec hex filename
6866 1040 128 8034 1f62 hns3/hns3vf/hclgevf_cmd.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 281 bytes.
Before:
text data bss dec hex filename
87553 5672 0 93225 16c29 benet/be_cmds.o
After:
text data bss dec hex filename
87112 5832 0 92944 16b10 benet/be_cmds.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may have some SoCs that can't achieve XGMAC max speed. Limit it if
asked to.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test to validate that Split Header feature is working correctly.
It works by using the rececently introduced counter that increments each
time a packet with split header is received.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are already doing it by default in the TX path so we can also enable
Jumbo Frame support in the RX path independently of MTU value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to set the RX tail pointer so that RX engine starts working
again after finishing the Flow Control test.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checks for support of Source Address Insertion/Replacement before
running the test.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF NIC may go down then come up during host servicing events. This
causes the VF NIC offloading feature settings to roll back to the
defaults. This patch can synchronize features from synthetic NIC to
the VF NIC during ndo_set_features (ethtool -K),
and netvsc_register_vf when VF comes back after host events.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Mark Bloch <markb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a previous patch, the NETIF_F_SG was missing after the code changes.
That caused the SG feature to be "fixed". This patch includes it into
hw_features, so it is tunable again.
Fixes: 23312a3be999 ("netvsc: negotiate checksum and segmentation parameters")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
mlx5-updates-2019-09-05
1) Allover mlx5 cleanups
2) Added port congestion counters to ethtool stats:
Add 3 counters per priority to ethtool using PPCNT:
2.1) rx_prio[p]_buf_discard - the number of packets discarded by device
due to lack of per host receive buffers
2.2) rx_prio[p]_cong_discard - the number of packets discarded by device
due to per host congestion
2.3) rx_prio[p]_marked - the number of packets ECN marked by device due
to per host congestion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 36f1031c51a2 ("ibmvnic: Do not process reset during or after
device removal") made the change to exit reset if the driver has been
removed, but does not free reset work items of the adapter from queue.
Ensure all reset work items are freed when breaking out of the loop early.
Fixes: 36f1031c51a2 ("ibmnvic: Do not process reset during or after device removal”)
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We 'allocate' 'count' bytes here. In fact, 'dev_alloc_skb' already add some
extra space for padding, so a bit more is allocated.
However, we use 1 byte for the KISS command, then copy 'count' bytes, so
count+1 bytes.
Explicitly allocate and use 1 more byte to be safe.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-09-05
This series contains updates to ice driver.
Brett fixes the setting of num_q_vectors by using the maximum number
between the allocated transmit and receive queues.
Anirudh simplifies the code to use a helper function to return the main
VSI, which is the first element in the pf->vsi array. Adds a pointer
check to prevent a NULL pointer dereference. Adds a check to ensure we
do not initialize DCB on devices that are not DCB capable. Does some
housekeeping on the code to remove unnecessary indirection and reduce
the PF structure by removing elements that are not needed since the
values they were storing can be readily gotten from
ice_get_avail_*_count()'s. Updates the printed strings to make it
easier to search the logs for driver capabilities.
Jesse cleans up unnecessary function arguments. Updated the code to use
prefetch() to add some efficiency to the driver to avoid a cache miss.
Did some housekeeping on the code to remove the configurable transmit
work limit via ethtool which ended up creating performance overhead.
Made additional performance enhancements by updating the driver to start
out with a reasonable number of descriptors by changing the default to
2048.
Mitch fixes the reset logic for VFs by clearing VF_MBX_ARQLEN register
when the source of the reset is not PFR.
Lukasz updates the driver to include a similar fix for the i40e driver
by reporting link down for VF's when the PF queues are not enabled.
Akeem updates the driver to report the VF link status once we get VF
resources so that we can reflect the link status similarly to how the PF
reports link speed.
Ashish updates the transmit context structure based on recent changes to
the hardware specification.
Dave updates the DCB logic to allow a delayed registration for MIB
change events so that the driver is not accepting events before it is
ready for them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 5.4
Second set of patches for 5.4. Lots of changes for iwlwifi and mt76,
but also smaller changes to other drivers.
Major changes:
iwlwifi
* remove broken and unused runtime power management mode for PCIe
devices, removes IWLWIFI_PCIE_RTPM Kconfig option as well
* support new ACPI value for per-platform antenna gain
* support for single antenna diversity
* support for new WoWLAN FW API
brcmfmac
* add reset debugfs file for testing firmware restart
mt76
* DFS pattern detector for mt7615 (DFS channels not enabled yet)
* Channel Switch Announcement (CSA) support for mt7615
* new device support for mt76x0
* support for more ciphers in mt7615
* smart carrier sense on mt7615
* survey support on mt7615
* multiple interfaces on mt76x02u
rtw88
* enable MSI interrupt
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patches intended for v5.4
* Remove (broken) d0i3 support;
* Debug infrastructure work continues;
* Bump support FW API version to 50;
* Fix for the SN value in certain suspend/resume situations;
* Some work on new FW scan APIs;
* Work on LTR FW APIs;
* New FW channel-switch support;
* Support new ACPI value for per-platform antenna gain;
* Support for single antenna diversity;
* Support for new WoWLAN FW API;
* Initial refactoring of the device selection code;
* A bunch of clean-ups;
* Other small fixes and improvements;
|
|
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable rx_process_result is being initialized with a value that
is never read and is being re-assigned immediately afterwards. The
assignment is redundant, so replace it with the return from function
lan743x_rx_process_packet.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only use the TROCR register on R-Car Gen3 as it is not present on other
SoCs.
Offsets used for the undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas it
remains unclear why this driver accesses these fields on R-Car Gen2 but
regardless of what the historical reasons are the current code is
considered incorrect.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the use of the undocumented BOC bit of the CCC register.
Current documentation for EtherAVB (ravb) describes the offset of what the
driver uses as the BOC bit as reserved and that only a value of 0 should be
written. After some internal investigation with Renesas it remains unclear
why this driver accesses these fields but regardless of what the historical
reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the use of the undocumented counter registers
CDCR, LCCR, CERCR, CEECR.
Offsets used for undocumented registers are considered reserved and
should not be written to. After some internal investigation with Renesas
it remains unclear why this driver accesses these fields but regardless of
what the historical reasons are the current code is considered incorrect.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The field name is FBP rather than FPB.
This field is unused and could equally be removed from the driver entirely.
But there seems no harm in leaving as documentation of the presence of the
field.
Based on work by Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Obviously, variable 'copied' is initialized to zero. But it is not used.
hence just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Wen Gong
Colin Ian King
Michal Suchanek
Mariusz Stachura
Sasha Neftin
Firo Yang
Mauro S. M. Rodrigues
Mitch Williams
Jacob Keller
Kai-Heng Feng
Radoslaw Tyl
YueHaibing
Fred Lotter
Jose Abreu
Haiyang Zhang
David S. Miller
Juliet Kim
Stefan Chulski
zhong jiang
Christophe JAILLET
Kalle Valo
Simon Horman
Andy Shevchenko
Wei Yongjun
Rafał Miłecki