aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2022-05-06net: dsa: felix: use PGID_CPU for FDB entry migration on NPI portVladimir Oltean1-4/+2
ocelot_fdb_add() redirects FDB entries installed on the NPI port towards the special reserved PGID_CPU used for host-filtered addresses. PGID_CPU contains BIT(ocelot->num_phys_ports) in the destination port mask, which is code name for the CPU port module. Whereas felix_migrate_fdbs_to_*_port() uses the ocelot->num_phys_ports PGID directly, and it appears that this works too. Even if this PGID is set to zero, apparently its number is special and packets still reach the CPU port module. Nonetheless, in the end, these addresses end up in the same place regardless of whether they go through an extra indirection layer or not. Use PGID_CPU across to have more uniformity. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-06mlxbf_gige: increase MDIO polling rate to 5usDavid Thompson1-2/+4
This patch increases the polling rate used by the mlxbf_gige driver on the MDIO bus. The previous polling rate was every 100us, and the new rate is every 5us. With this change the amount of time spent waiting for the MDIO BUSY signal to de-assert drops from ~100us to ~27us for each operation. Signed-off-by: David Thompson <davthompson@nvidia.com> Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com> Link: https://lore.kernel.org/r/20220505162309.20050-1-davthompson@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-06net: chelsio: cxgb4: Avoid potential negative array offsetKees Cook1-5/+5
Using min_t(int, ...) as a potential array index implies to the compiler that negative offsets should be allowed. This is not the case, though. Replace "int" with "unsigned int". Fixes the following warning exposed under future CONFIG_FORTIFY_SOURCE improvements: In file included from include/linux/string.h:253, from include/linux/bitmap.h:11, from include/linux/cpumask.h:12, from include/linux/smp.h:13, from include/linux/lockdep.h:14, from include/linux/rcupdate.h:29, from include/linux/rculist.h:11, from include/linux/pid.h:5, from include/linux/sched.h:14, from include/linux/delay.h:23, from drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:35: drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function 't4_get_raw_vpd_params': include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 29 and size [2147483648, 4294967295] [-Warray-bounds] 46 | #define __underlying_memcpy __builtin_memcpy | ^ include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy' 388 | __underlying_##op(p, q, __fortify_size); \ | ^~~~~~~~~~~~~ include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk' 433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \ | ^~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2796:9: note: in expansion of macro 'memcpy' 2796 | memcpy(p->id, vpd + id, min_t(int, id_len, ID_LEN)); | ^~~~~~ include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 0 and size [2147483648, 4294967295] [-Warray-bounds] 46 | #define __underlying_memcpy __builtin_memcpy | ^ include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy' 388 | __underlying_##op(p, q, __fortify_size); \ | ^~~~~~~~~~~~~ include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk' 433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \ | ^~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2798:9: note: in expansion of macro 'memcpy' 2798 | memcpy(p->sn, vpd + sn, min_t(int, sn_len, SERNUM_LEN)); | ^~~~~~ Additionally remove needless cast from u8[] to char * in last strim() call. Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/lkml/202205031926.FVP7epJM-lkp@intel.com Fixes: fc9279298e3a ("cxgb4: Search VPD with pci_vpd_find_ro_info_keyword()") Fixes: 24c521f81c30 ("cxgb4: Use pci_vpd_find_id_string() to find VPD ID string") Cc: Raju Rangoju <rajur@chelsio.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220505233101.1224230-1-keescook@chromium.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-06Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski2-4/+4
Tony Nguyen says: ==================== 10GbE Intel Wired LAN Driver Updates 2022-05-05 This series contains updates to ixgbe and igb drivers. Jeff Daly adjusts type for 'allow_unsupported_sfp' to match the associated struct value for ixgbe. Alaa Mohamed converts, deprecated, kmap() call to kmap_local_page() for igb. * '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: igb: Convert kmap() to kmap_local_page() ixgbe: Fix module_param allow_unsupported_sfp type ==================== Link: https://lore.kernel.org/r/20220505155651.2606195-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-06ice: fix PTP stale Tx timestamps cleanupMichal Michalik1-2/+8
Read stale PTP Tx timestamps from PHY on cleanup. After running out of Tx timestamps request handlers, hardware (HW) stops reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used to only clean up stale handlers in driver and was leaving the hardware registers not read. Not reading stale PTP Tx timestamps prevents next interrupts from arriving and makes timestamping unusable. Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices") Signed-off-by: Michal Michalik <michal.michalik@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06ice: clear stale Tx queue settings before configuringAnatolii Gerasymenko1-18/+50
The iAVF driver uses 3 virtchnl op codes to communicate with the PF regarding the VF Tx queues: * VIRTCHNL_OP_CONFIG_VSI_QUEUES configures the hardware and firmware logic for the Tx queues * VIRTCHNL_OP_ENABLE_QUEUES configures the queue interrupts * VIRTCHNL_OP_DISABLE_QUEUES disables the queue interrupts and Tx rings. There is a bug in the iAVF driver due to the race condition between VF reset request and shutdown being executed in parallel. This leads to a break in logic and VIRTCHNL_OP_DISABLE_QUEUES is not being sent. If this occurs, the PF driver never cleans up the Tx queues. This results in leaving behind stale Tx queue settings in the hardware and firmware. The most obvious outcome is that upon the next VIRTCHNL_OP_CONFIG_VSI_QUEUES, the PF will fail to program the Tx scheduler node due to a lack of space. We need to protect ICE driver against such situation. To fix this, make sure we clear existing stale settings out when handling VIRTCHNL_OP_CONFIG_VSI_QUEUES. This ensures we remove the previous settings. Calling ice_vf_vsi_dis_single_txq should be safe as it will do nothing if the queue is not configured. The function already handles the case when the Tx queue is not currently configured and exits with a 0 return in that case. Fixes: 7ad15440acf8 ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06ice: Fix race during aux device (un)pluggingIvan Vecera3-8/+20
Function ice_plug_aux_dev() assigns pf->adev field too early prior aux device initialization and on other side ice_unplug_aux_dev() starts aux device deinit and at the end assigns NULL to pf->adev. This is wrong because pf->adev should always be non-NULL only when aux device is fully initialized and ready. This wrong order causes a crash when ice_send_event_to_aux() call occurs because that function depends on non-NULL value of pf->adev and does not assume that aux device is half-initialized or half-destroyed. After order correction the race window is tiny but it is still there, as Leon mentioned and manipulation with pf->adev needs to be protected by mutex. Fix (un-)plugging functions so pf->adev field is set after aux device init and prior aux device destroy and protect pf->adev assignment by new mutex. This mutex is also held during ice_send_event_to_aux() call to ensure that aux device is valid during that call. Note that device lock used ice_send_event_to_aux() needs to be kept to avoid race with aux drv unload. Reproducer: cycle=1 while :;do echo "#### Cycle: $cycle" ip link set ens7f0 mtu 9000 ip link add bond0 type bond mode 1 miimon 100 ip link set bond0 up ifenslave bond0 ens7f0 ip link set bond0 mtu 9000 ethtool -L ens7f0 combined 1 ip link del bond0 ip link set ens7f0 mtu 1500 sleep 1 let cycle++ done In short when the device is added/removed to/from bond the aux device is unplugged/plugged. When MTU of the device is changed an event is sent to aux device asynchronously. This can race with (un)plugging operation and because pf->adev is set too early (plug) or too late (unplug) the function ice_send_event_to_aux() can touch uninitialized or destroyed fields. In the case of crash below pf->adev->dev.mutex. Crash: [ 53.372066] bond0: (slave ens7f0): making interface the new active one [ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u p link [ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up link [ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval idating tc mappings. Priority traffic classification disabled! [ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval idating tc mappings. Priority traffic classification disabled! [ 54.248204] bond0: (slave ens7f0): Releasing backup interface [ 54.253955] bond0: (slave ens7f1): making interface the new active one [ 54.274875] bond0: (slave ens7f1): Releasing backup interface [ 54.289153] bond0 (unregistering): Released all slaves [ 55.383179] MII link monitoring set to 100 ms [ 55.398696] bond0: (slave ens7f0): making interface the new active one [ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080 [ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u p link [ 55.412198] #PF: supervisor write access in kernel mode [ 55.412200] #PF: error_code(0x0002) - not-present page [ 55.412201] PGD 25d2ad067 P4D 0 [ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI [ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S 5.17.0-13579-g57f2d6540f03 #1 [ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up link [ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/ 2021 [ 55.430226] Workqueue: ice ice_service_task [ice] [ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20 [ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48 [ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246 [ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001 [ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080 [ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041 [ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0 [ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000 [ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000 [ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0 [ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 55.567305] PKRU: 55555554 [ 55.570018] Call Trace: [ 55.572474] <TASK> [ 55.574579] ice_service_task+0xaab/0xef0 [ice] [ 55.579130] process_one_work+0x1c5/0x390 [ 55.583141] ? process_one_work+0x390/0x390 [ 55.587326] worker_thread+0x30/0x360 [ 55.590994] ? process_one_work+0x390/0x390 [ 55.595180] kthread+0xe6/0x110 [ 55.598325] ? kthread_complete_and_exit+0x20/0x20 [ 55.603116] ret_from_fork+0x1f/0x30 [ 55.606698] </TASK> Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA") Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06Revert "ice: Hide bus-info in ethtool for PRs in switchdev mode"Marcin Szycik1-5/+3
This reverts commit bfaaba99e680bf82bf2cbf69866c3f37434ff766. Commit bfaaba99e680 ("ice: Hide bus-info in ethtool for PRs in switchdev mode") was a workaround for lshw tool displaying incorrect descriptions for port representors and PF in switchdev mode. Now the issue has been fixed in the lshw tool itself [1]. Removing the workaround can be considered a regression, as the user might be running older, unpatched lshw version. However, another important change (ice: link representors to PCI device, which improves port representor netdev naming with SET_NETDEV_DEV) also causes the same "regression" as removing the workaround, i.e. unpatched lshw is able to access bus-info information (this time not via ethtool) and the bug can occur. Therefore, the workaround no longer prevents the bug and can be removed. [1] https://ezix.org/src/pkg/lshw/commit/9bf4e4c9c1 Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06ice: link representors to PCI deviceMichal Swiatkowski1-0/+1
Link port representors to parent PCI device to benefit from systemd defined naming scheme. Example from ip tool: - without linking: eth0 ... - with linking: eth0 ... altname enp24s0f0npf0vf0 The port representor name is being shown in altname, because the name is longer than IFNAMSIZ (16) limit. Altname can be used in ip tool. Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-06net: make drivers set the TSO limit not the GSO limitJakub Kicinski24-36/+39
Drivers should call the TSO setting helper, GSO is controllable by user space. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06net: add netif_inherit_tso_max()Jakub Kicinski5-14/+7
To make later patches smaller create a helper for inheriting the TSO limitations of a lower device. The TSO in the name is not an accident, subsequent patches will replace GSO with TSO in more names. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: enable decap_v2 bitLouis Peens1-1/+2
Finally enable the decap_v2 feature bit now that all the other bits are in place to configure it correctly. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: remove unused neighbour cacheLouis Peens2-183/+0
With the neighbour entries now stored in a dedicated table there is no use to make use of the tunnel route cache anymore, so remove this. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: link pre_tun flow rules with neigh entriesLouis Peens3-1/+154
Add helper functions that can create links between flow rules and cached neighbour entries. Also add the relevant calls to these functions. * When a new neighbour entry gets added cycle through the saved pre_tun flow list and link any relevant matches. Update the neighbour table on the nfp with this new information. * When a new pre_tun flow rule gets added iterate through the save neighbour entries and link any relevant matches. Once again update the nfp neighbour table with any new links. * Do the inverse when deleting - remove any created links and also inform the nfp of this. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: rework tunnel neighbour configurationLouis Peens1-55/+111
This patch updates the way in which the tunnel neighbour entries are handled. Previously they were mostly send-and-forget, with just the destination IP's cached in a list. This update changes to a scheme where the neighbour entry information is stored in a hash table. The reason for this is that the neighbour table will now also be used on the decapsulation path, whereas previously it was only used for encapsulation. We need to save more of the neighbour information in order to link them with flower flows in follow up patches. Updating of the neighbour table is now also handled by the same function, instead of separate *_write_neigh_vX functions. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: update nfp_tun_neigh structsLouis Peens2-33/+47
Prepare for more rework in following patches by updating the existing nfp_neigh_structs. The update allows for the same headers to be used for both old and new firmware, with a slight length adjustment when sending the control message to the firmware. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: fixup ipv6/ipv4 route lookup for neigh eventsLouis Peens1-17/+31
When a callback is received to invalidate a neighbour entry there is no need to try and populate any other flow information. Only the flowX->daddr information is needed as lookup key to delete an entry from the NFP neighbour table. Fix this by only doing the lookup if the callback is for a new entry. As part of this cleanup remove the setting of flow6.flowi6_proto, as this is not needed either, it looks to be a possible leftover from a previous implementation. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: enforce more strict pre_tun checksLouis Peens1-7/+34
Make sure that the rule also matches on source MAC address. On top of that also now save the src and dst MAC addresses similar to how vlan_tci is saved - this will be used in later comparisons with neighbour entries. Indicate if the flow matched on ipv4 or ipv6. Populate the vlan_tpid field that got added to the pre_run_rule struct as well. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: add/remove predt_list entriesLouis Peens2-7/+39
Add calls to add and remove flows to the predt_table. This very simply just allocates and add a new pretun entry if detected as such, and removes it when encountered on a delete flow. Compatibility for older firmware is kept in place through the DECAP_V2 feature bit. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06nfp: flower: add infrastructure for pre_tun reworkLouis Peens3-33/+105
The previous implementation of using a pre_tun_table for decap has some limitations, causing flows to end up unoffloaded when in fact we are able to offload them. This is because the pre_tun_table does not have enough matching resolution. The next step is to instead make use of the neighbour table which already exists for the encap direction. This patch prepares for this by: - Moving nfp_tun_neigh/_v6 to main.h. - Creating two new "wrapping" structures, one to keep track of neighbour entries (previously they were send-and-forget), and another to keep track of pre_tun flows. - Create a new list in nfp_flower_priv to keep track of pre_tunnel flows - Create a new table in nfp_flower_priv to keep track of next neighbour entries - Initialising and destroying these new list/tables - Extending nfp_fl_payload->pre_tun_rule to save more information for future use. Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller13-53/+150
Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2022-05-05 This series contains updates to ice driver only. Wan Jiabing converts an open coded min selection to min_t(). Maciej commonizes on a single find VSI function and removes the duplicated implementation. Wojciech adjusts the return value when exceeding ICE_MAX_CHAIN_WORDS to, a more appropriate, -ENOSPC and allows for the error to be propagated. Michal adds support for ndo_get_devlink_port(). Jake does some cleanup related to virtualization code. Mainly involving function header comments and wording changes. NULL checks are added to ice_get_vf_vsi() calls in order to prevent static analysis tools from complaining that a NULL value could be dereferenced. --- v2: Dropped patch 1: "ice: Add support for classid based queue selection" ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-06net/mlx5e: Use XFRM state direction instead of flagsLeon Romanovsky1-5/+5
Convert mlx5 driver to use XFRM state direction. Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2022-05-06netdevsim: rely on XFRM state direction instead of flagsLeon Romanovsky1-1/+1
Make sure that netdevsim relies on direction and not on flags. Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2022-05-06ixgbe: propagate XFRM offload state direction instead of flagsLeon Romanovsky4-10/+9
Convert the ixgbe driver to rely on XFRM offload state direction instead of flags bits that were not checked at all. Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2022-05-06ath11k: Fix RX de-fragmentation issue on WCN6750Manikanta Pubbisetty3-3/+23
The offset of REO register where the RX fragment destination ring is configured is different in WCN6750 as compared to WCN6855. Due to this differnce in offsets, on WCN6750, fragment destination ring will be configured incorrectly, leading to RX fragments not getting delivered to the driver. Fix this by defining HW specific offsets for the REO MISC CTL register. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220504083900.31513-1-quic_mpubbise@quicinc.com
2022-05-06ath10k: support bus and device specific API 1 BDF selectionRobert Marko1-1/+12
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the BDF-s to be extracted from the device storage instead of shipping packaged API 2 BDF-s. This is required as MikroTik has started shipping boards that require BDF-s to be updated, as otherwise their WLAN performance really suffers. This is however impossible as the devices that require this are release under the same revision and its not possible to differentiate them from devices using the older BDF-s. In OpenWrt we are extracting the calibration data during runtime and we are able to extract the BDF-s in the same manner, however we cannot package the BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on the fly. This is an issue as the ath10k driver explicitly looks only for the board.bin file and not for something like board-bus-device.bin like it does for pre-cal data. Due to this we have no way of providing correct BDF-s on the fly, so lets extend the ath10k driver to first look for BDF-s in the board-bus-device.bin format, for example: board-ahb-a800000.wifi.bin If that fails, look for the default board file name as defined previously. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211009221711.2315352-1-robimarko@gmail.com
2022-05-06ath10k: mac: fix too long linesKalle Valo1-4/+9
checkpatch warns: drivers/net/wireless/ath/ath10k/mac.c:2696: line length of 92 exceeds 90 columns drivers/net/wireless/ath/ath10k/mac.c:6942: line length of 94 exceeds 90 columns drivers/net/wireless/ath/ath10k/mac.c:6948: line length of 91 exceeds 90 columns These were introduced by commit 046d2e7c50e3 ("mac80211: prepare sta handling for MLO support"). Compile tested only. Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220503060415.24499-2-kvalo@kernel.org
2022-05-06ath11k: mac: fix too long lineKalle Valo1-4/+8
checkpatch warns: drivers/net/wireless/ath/ath11k/mac.c:7760: line length of 91 exceeds 90 columns This was introduced by commit 046d2e7c50e3 ("mac80211: prepare sta handling for MLO support"). Compile tested only. Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220503060415.24499-1-kvalo@kernel.org
2022-05-06wl1251: dynamically allocate memory used for DMAH. Nikolaus Schaller3-18/+39
With introduction of vmap'ed stacks, stack parameters can no longer be used for DMA and now leads to kernel panic. It happens at several places for the wl1251 (e.g. when accessed through SDIO) making it unuseable on e.g. the OpenPandora. We solve this by allocating temporary buffers or use wl1251_read32(). Tested on v5.18-rc5 with OpenPandora. Fixes: a1c510d0adc6 ("ARM: implement support for vmap'ed stacks") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1676021ae8b6d7aada0b1806fed99b1b8359bdc4.1651495112.git.hns@goldelico.com
2022-05-06qtnfmac: switch to netif_napi_add_weight()Jakub Kicinski2-4/+4
qtnfmac chooses its own magic NAPI weight so switch to the new API created for those who don't use NAPI_POLL_WEIGHT. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220504163316.549648-4-kuba@kernel.org
2022-05-06mt76: switch to netif_napi_add_tx()Jakub Kicinski5-10/+10
Switch to the new API not requiring passing in NAPI_POLL_WEIGHT. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220504163316.549648-3-kuba@kernel.org
2022-05-06wil6210: switch to netif_napi_add_tx()Jakub Kicinski1-6/+4
Switch to the new API not requiring passing in NAPI_POLL_WEIGHT. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220504163316.549648-2-kuba@kernel.org
2022-05-05net: mscc: ocelot: avoid corrupting hardware counters when moving VCAP filtersVladimir Oltean1-0/+4
Given the following order of operations: (1) we add filter A using tc-flower (2) we send a packet that matches it (3) we read the filter's statistics to find a hit count of 1 (4) we add a second filter B with a higher preference than A, and A moves one position to the right to make room in the TCAM for it (5) we send another packet, and this matches the second filter B (6) we read the filter statistics again. When this happens, the hit count of filter A is 2 and of filter B is 1, despite a single packet having matched each filter. Furthermore, in an alternate history, reading the filter stats a second time between steps (3) and (4) makes the hit count of filter A remain at 1 after step (6), as expected. The reason why this happens has to do with the filter->stats.pkts field, which is written to hardware through the call path below: vcap_entry_set / | \ / | \ / | \ / | \ es0_entry_set is1_entry_set is2_entry_set \ | / \ | / \ | / vcap_data_set(data.counter, ...) The primary role of filter->stats.pkts is to transport the filter hit counters from the last readout all the way from vcap_entry_get() -> ocelot_vcap_filter_stats_update() -> ocelot_cls_flower_stats(). The reason why vcap_entry_set() writes it to hardware is so that the counters (saturating and having a limited bit width) are cleared after each user space readout. The writing of filter->stats.pkts to hardware during the TCAM entry movement procedure is an unintentional consequence of the code design, because the hit count isn't up to date at this point. So at step (4), when filter A is moved by ocelot_vcap_filter_add() to make room for filter B, the hardware hit count is 0 (no packet matched on it in the meantime), but filter->stats.pkts is 1, because the last readout saw the earlier packet. The movement procedure programs the old hit count back to hardware, so this creates the impression to user space that more packets have been matched than they really were. The bug can be seen when running the gact_drop_and_ok_test() from the tc_actions.sh selftest. Fix the issue by reading back the hit count to tmp->stats.pkts before migrating the VCAP filter. Sure, this is a best-effort technique, since the packets that hit the rule between vcap_entry_get() and vcap_entry_set() won't be counted, but at least it allows the counters to be reliably used for selftests where the traffic is under control. The vcap_entry_get() name is a bit unintuitive, but it only reads back the counter portion of the TCAM entry, not the entire entry. The index from which we retrieve the counter is also a bit unintuitive (i - 1 during add, i + 1 during del), but this is the way in which TCAM entry movement works. The "entry index" isn't a stored integer for a TCAM filter, instead it is dynamically computed by ocelot_vcap_block_get_filter_index() based on the entry's position in the &block->rules list. That position (as well as block->count) is automatically updated by ocelot_vcap_filter_add_to_block() on add, and by ocelot_vcap_block_remove_filter() on del. So "i" is the new filter index, and "i - 1" or "i + 1" respectively are the old addresses of that TCAM entry (we only support installing/deleting one filter at a time). Fixes: b596229448dd ("net: mscc: ocelot: Add support for tcam") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: mscc: ocelot: restrict tc-trap actions to VCAP IS2 lookup 0Vladimir Oltean1-2/+3
Once the CPU port was added to the destination port mask of a packet, it can never be cleared, so even packets marked as dropped by the MASK_MODE of a VCAP IS2 filter will still reach it. This is why we need the OCELOT_POLICER_DISCARD to "kill dropped packets dead" and make software stop seeing them. We disallow policer rules from being put on any other chain than the one for the first lookup, but we don't do this for "drop" rules, although we should. This change is merely ascertaining that the rules dont't (completely) work and letting the user know. The blamed commit is the one that introduced the multi-chain architecture in ocelot. Prior to that, we should have always offloaded the filters to VCAP IS2 lookup 0, where they did work. Fixes: 1397a2eb52e2 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: mscc: ocelot: fix VCAP IS2 filters matching on both lookupsVladimir Oltean1-1/+0
The VCAP IS2 TCAM is looked up twice per packet, and each filter can be configured to only match during the first, second lookup, or both, or none. The blamed commit wrote the code for making VCAP IS2 filters match only on the given lookup. But right below that code, there was another line that explicitly made the lookup a "don't care", and this is overwriting the lookup we've selected. So the code had no effect. Some of the more noticeable effects of having filters match on both lookups: - in "tc -s filter show dev swp0 ingress", we see each packet matching a VCAP IS2 filter counted twice. This throws off scripts such as tools/testing/selftests/net/forwarding/tc_actions.sh and makes them fail. - a "tc-drop" action offloaded to VCAP IS2 needs a policer as well, because once the CPU port becomes a member of the destination port mask of a packet, nothing removes it, not even a PERMIT/DENY mask mode with a port mask of 0. But VCAP IS2 rules with the POLICE_ENA bit in the action vector can only appear in the first lookup. What happens when a filter matches both lookups is that the action vector is combined, and this makes the POLICE_ENA bit ineffective, since the last lookup in which it has appeared is the second one. In other words, "tc-drop" actions do not drop packets for the CPU port, dropped packets are still seen by software unless there was an FDB entry that directed those packets to some other place different from the CPU. The last bit used to work, because in the initial commit b596229448dd ("net: mscc: ocelot: Add support for tcam"), we were writing the FIRST field of the VCAP IS2 half key with a 1, not with a "don't care". The change to "don't care" was made inadvertently by me in commit c1c3993edb7c ("net: mscc: ocelot: generalize existing code for VCAP"), which I just realized, and which needs a separate fix from this one, for "stable" kernels that lack the commit blamed below. Fixes: 226e9cd82a96 ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: mscc: ocelot: fix last VCAP IS1/IS2 filter persisting in hardware when deletedVladimir Oltean1-0/+4
ocelot_vcap_filter_del() works by moving the next filters over the current one, and then deleting the last filter by calling vcap_entry_set() with a del_filter which was specially created by memsetting its memory to zeroes. vcap_entry_set() then programs this to the TCAM and action RAM via the cache registers. The problem is that vcap_entry_set() is a dispatch function which looks at del_filter->block_id. But since del_filter is zeroized memory, the block_id is 0, or otherwise said, VCAP_ES0. So practically, what we do is delete the entry at the same TCAM index from VCAP ES0 instead of IS1 or IS2. The code was not always like this. vcap_entry_set() used to simply be is2_entry_set(), and then, the logic used to work. Restore the functionality by populating the block_id of the del_filter based on the VCAP block of the filter that we're deleting. This makes vcap_entry_set() know what to do. Fixes: 1397a2eb52e2 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: mscc: ocelot: mark traps with a bool instead of keeping them in a listVladimir Oltean3-12/+10
Since the blamed commit, VCAP filters can appear on more than one list. If their action is "trap", they are chained on ocelot->traps via filter->trap_list. This is in addition to their normal placement on the VCAP block->rules list head. Therefore, when we free a VCAP filter, we must remove it from all lists it is a member of, including ocelot->traps. There are at least 2 bugs which are direct consequences of this design decision. First is the incorrect usage of list_empty(), meant to denote whether "filter" is chained into ocelot->traps via filter->trap_list. This does not do the correct thing, because list_empty() checks whether "head->next == head", but in our case, head->next == head->prev == NULL. So we dereference NULL pointers and die when we call list_del(). Second is the fact that not all places that should remove the filter from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(), which is where we have the main kfree(filter). By keeping freed filters in ocelot->traps we end up in a use-after-free in felix_update_trapping_destinations(). Attempting to fix all the buggy patterns is a whack-a-mole game which makes the driver unmaintainable. Actually this is what the previous patch version attempted to do: https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728.834457-3-vladimir.oltean@nxp.com/ but it introduced another set of bugs, because there are other places in which create VCAP filters, not just ocelot_vcap_filter_create(): - ocelot_trap_add() - felix_tag_8021q_vlan_add_rx() - felix_tag_8021q_vlan_add_tx() Relying on the convention that all those code paths must call INIT_LIST_HEAD(&filter->trap_list) is not going to scale. So let's do what should have been done in the first place and keep a bool in struct ocelot_vcap_filter which denotes whether we are looking at a trapping rule or not. Iterating now happens over the main VCAP IS2 block->rules. The advantage is that we no longer risk having stale references to a freed filter, since it is only present in that list. Fixes: e42bd4ed09aa ("net: mscc: ocelot: keep traps in a list") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: phy: micrel: Pass .probe for KS8737Fabio Estevam1-0/+1
Since commit f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices") the kszphy_suspend/ resume hooks are used. These functions require the probe function to be called so that priv can be allocated. Otherwise, a NULL pointer dereference happens inside kszphy_config_reset(). Cc: stable@vger.kernel.org Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220504143104.1286960-2-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061Fabio Estevam1-2/+2
Since commit f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices") the following NULL pointer dereference is observed on a board with KSZ8061: # udhcpc -i eth0 udhcpc: started, v1.35.0 8<--- cut here --- Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = f73cef4e [00000008] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94 Hardware name: Freescale i.MX6 SoloX (Device Tree) PC is at kszphy_config_reset+0x10/0x114 LR is at kszphy_resume+0x24/0x64 ... The KSZ8061 phy_driver structure does not have the .probe/..driver_data fields, which means that priv is not allocated. This causes the NULL pointer dereference inside kszphy_config_reset(). Fix the problem by using the generic suspend/resume functions as before. Another alternative would be to provide the .probe and .driver_data information into the structure, but to be on the safe side, let's just restore Ethernet functionality by using the generic suspend/resume. Cc: stable@vger.kernel.org Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices") Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220504143104.1286960-1-festevam@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: move snowflake callers to netif_napi_add_tx_weight()Jakub Kicinski3-7/+8
Make the drivers with custom tx napi weight call netif_napi_add_tx_weight(). Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Link: https://lore.kernel.org/r/20220504163725.550782-2-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: switch to netif_napi_add_tx()Jakub Kicinski17-36/+26
Switch net callers to the new API not requiring the NAPI_POLL_WEIGHT argument. Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Acked-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20220504163725.550782-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05jme: remove an unnecessary indirectionJakub Kicinski2-3/+1
Remove a define which looks like a OS abstraction layer and makes spatch conversions on this driver problematic. Link: https://lore.kernel.org/r/20220504163939.551231-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05net: ethernet: Prepare cleanup of powerpc's asm/prom.hChristophe Leroy9-3/+8
powerpc's asm/prom.h includes some headers that it doesn't need itself. In order to clean powerpc's asm/prom.h up in a further step, first clean all files that include asm/prom.h Some files don't need asm/prom.h at all. For those ones, just remove inclusion of asm/prom.h Some files don't need any of the items provided by asm/prom.h, but need some of the headers included by asm/prom.h. For those ones, add the needed headers that are brought by asm/prom.h at the moment and remove asm/prom.h Some files really need asm/prom.h but also need some of the headers included by asm/prom.h. For those one, leave asm/prom.h but also add the needed headers so that they can be removed from asm/prom.h in a later step. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Link: https://lore.kernel.org/r/09a13d592d628de95d30943e59b2170af5b48110.1651663857.git.christophe.leroy@csgroup.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05sungem: Prepare cleanup of powerpc's asm/prom.hChristophe Leroy1-5/+1
powerpc's <asm/prom.h> includes some headers that it doesn't need itself. In order to clean powerpc's <asm/prom.h> up in a further step, first clean all files that include <asm/prom.h> sungem_phy.c doesn't use any object provided by <asm/prom.h>. But removing inclusion of <asm/prom.h> leads to the following errors: CC drivers/net/sungem_phy.o drivers/net/sungem_phy.c: In function 'bcm5421_init': drivers/net/sungem_phy.c:448:42: error: implicit declaration of function 'of_get_parent'; did you mean 'dget_parent'? [-Werror=implicit-function-declaration] 448 | struct device_node *np = of_get_parent(phy->platform_data); | ^~~~~~~~~~~~~ | dget_parent drivers/net/sungem_phy.c:448:42: warning: initialization of 'struct device_node *' from 'int' makes pointer from integer without a cast [-Wint-conversion] drivers/net/sungem_phy.c:450:35: error: implicit declaration of function 'of_get_property' [-Werror=implicit-function-declaration] 450 | if (np == NULL || of_get_property(np, "no-autolowpower", NULL)) | ^~~~~~~~~~~~~~~ Remove <asm/prom.h> from included headers but add <linux/of.h> to handle the above. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Link: https://lore.kernel.org/r/f7a7fab3ec5edf803d934fca04df22631c2b449d.1651662885.git.christophe.leroy@csgroup.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05Revert "Merge branch 'mlxsw-line-card-model'"Jakub Kicinski3-321/+4
This reverts commit 5e927a9f4b9f29d78a7c7d66ea717bb5c8bbad8e, reversing changes made to cfc1d91a7d78cf9de25b043d81efcc16966d55b3. The discussion is still ongoing so let's remove the uAPI until the discussion settles. Link: https://lore.kernel.org/all/20220425090021.32e9a98f@kernel.org/ Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220504154037.539442-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski36-213/+368
tools/testing/selftests/net/forwarding/Makefile f62c5acc800e ("selftests/net/forwarding: add missing tests to Makefile") 50fe062c806e ("selftests: forwarding: new test, verify host mdb entries") https://lore.kernel.org/all/20220502111539.0b7e4621@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05ice: remove period on argument description in ice_for_each_vfJacob Keller1-2/+2
The ice_for_each_vf macros have comments describing the implementation. One of the arguments has a period on the end, which is not our typical style. Remove the unnecessary period. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-05ice: add a function comment for ice_cfg_mac_antispoofJacob Keller1-0/+7
This function definition was missing a comment describing its implementation. Add one. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-05ice: fix wording in comment for ice_reset_vfJacob Keller1-2/+2
The comment explaining ice_reset_vf has an extraneous "the" with the "if the resets are disabled". Remove it. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-05-05ice: remove return value comment for ice_reset_all_vfsJacob Keller1-2/+2
Since commit fe99d1c06c16 ("ice: make ice_reset_all_vfs void"), the ice_reset_all_vfs function has not returned anything. The function comment still indicated it did. Fix this. While here, also add a line to clarify the function resets all VFs at once in response to hardware resets such as a PF reset. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.