| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver. Dumping the
device's memory is not necessary and just bloats the logs
with unusable data. Moreover, asking mac80211 to restart
the hardware is also useless. Bypass all this.
Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When the NIC is disconnected from PCI bus, we are not
able to access it anymore. Check the status to avoid
some unnecessary work so can improve the performance.
It will help to make PCI bus rescan to bring back the
device much faster.
The real test is able to improve 7 seconds.
[w/o patch] It takes around 9 seconds
..
2018-04-20T01:22:39.691929-07:00 WARNING kernel:
[ 66.335881] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:22:48.101094-07:00 INFO kernel:
[ 74.747364] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
[w/a patch] It takes about 2 seconds.
..
2018-04-20T01:18:16.454087-07:00 WARNING kernel:
[ 75.966860] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:18:18.602717-07:00 INFO kernel:
[ 78.116132] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
..
Fixes: 49564a806fc5 ("iwlwifi: pcie: remove non-responsive device")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no point in warning here, the user will just get an
error back to the debugfs file write, and warning just makes
it seem like there's an internal consistency problem when in
reality the user just happened to hit this at a bad time.
Remove the warning.
Fixes: f45f979dc208 ("iwlwifi: mvm: disable dbg data collect when fw isn't alive")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Every rx mpdu cmd is built from cmd_hdr | 80211_hdr. The problem is
that the size of cmd_hdr changes with API changes and we don't know
where the 80211_hdr starts.
By adding the size of cmd_hdr dynamically, we can ensure that we always
know how to parse mpdu frames, without dependending on the API changes.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This will allow using the same init in future generations.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Store the default rxq number in a variable, so we won't need
to use the actual number in the code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
While associated in low latency mode, or when traffic load is high,
don't enable EBS in scan request if fragmented EBS is not supported
by the FW.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The Free Software Foundation's address shouldn't be in the license
notice anymore, and some of our check scripts complain about it
(via checkpatch.pl). Remove the address to silence it.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is used only within PCIe, and there's no reason to go through
the transport methods for a function call within PCIe itself.
Remove the dump_regs() method and call the function directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Allow other device generations to use the utilities that
are used to send and reclaim host commands and to allocate
rx, by making it non-static.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We would like to allow using tx init code for other queues but
the command queue - for newer devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We need to drop packets with errors (such as replay,
MIC, ICV, conversion, duplicate and so on).
Drop invalid packets, put the status bits in the metadata and
move the enum definition to the correct place (FW API header).
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The user can validate what was written to the file by reading it,
and check what is the default value before changing it.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Current implementation turns this bit on only for HE MU.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add BSS color to the HE radiotap.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some variables are used in iwl-fh.h, but their type's definition
isn't included. This may break compilation when using the file
without including the necessary dependencies first.
Add the required include to iwl-fh.h.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A probe response built by a P2P GO should contain:
1. CSA/eCSA IE when relevant
2. If the corresponding probe request had P2P IE, then
need to add P2P IE with NOA attributes.
However, the NOA attributes and the updated channel switch
counter are known only to the FW. The solution is that FW
will send a notification with the relevant probe response
data and the driver will save it and update the probe
response accordingly.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys. Check the respective TLV and use the
new API when it is set.
Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.
Also refactor some functions a bit so that they can be reused more
easily. Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Runtime PM can only be used if CONFIG_PM is set. Move all the d0i3
code (which is essentially runtime PM) behind the CONFIG_PM flag.
This prevents undefined usage of some functions when CONFIG_PM is not
defined.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We repeated the same if twice in a row. Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The tid for Non-QOS frames is set to IWL_MAX_TID_COUNT. This value
is also used for configuring the queue for non-QOS data. However, this
tid is used by the FW for management queues. As a result, the FW
does not encrypt non-QOS data frames.
Fix this by setting the tid for non-QOS data frames to zero, which
is a valid value for data frames in the FW.
This also fixes a bug in sending multicast frames, where the queues
are allocated with tid == 0, but are sent with tid == 8, which may
lead to unexpected behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Upon first calling read() on a debugfs file, invoke
iwl_dbgfs_##name##_read and store the response buffer on the heap, so
subsequent read() calls don't need to invoke said function again.
This is done because cat etc will call read() repeatedly until EOF is
reached (or read() returns 0), which in the current implementation will
cause said function to be invoked multiple times.
With the current implementation this can also cause buggy behavior in
some weird edge cases where the first invocation returns a string of
length n, and the second of length m>n: The last m-n characters of
the second invocation will be printed to screen.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The iwl_dhc_tlc_cmd struct is not used, so remove it, including the
iwl_tcl_debug_flags enumeration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Don't enable debugging timestamps by default, so we save power by not
waking up the FW with timestamp commands.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
To prevent VF from deleting MAC address that was assigned by the
PF we need to check for that scenario when we try to delete a MAC
address from a VF.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If a VF is being removed, there is no need to continue with the
workqueue sync for the adminq task, thus cancel it. Without this call,
when VFs are created and removed right away, there might be a chance for
the driver to crash with events stuck in the adminq.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Hold the rtnl lock when we're clearing interrupt scheme
in i40e_shutdown and in i40e_remove.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With current implementation of i40evf_set_features when user sets
any offload via ethtool we set I40EVF_FLAG_AQ_ENABLE_VLAN_STRIPPING
as a required aq which triggers driver to call
i40evf_enable_vlan_stripping. This shouldn't take place.
This patches fixes it by setting the flag only when VLAN offload
is turned on.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If our card has been put in an unstable state due to
other drivers interacting with it, speed settings
might be incorrect. If incorrect, forcefully reset them
on open to known default values.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When XDP is enabled, the driver will report incorrect
statistics. Received frames will reported as transmitted frames.
This commits fixes the i40e implementation of ndo_get_stats64 (struct
net_device_ops), so that iproute2 will report correct statistics
(e.g. when running "ip -stats link show dev eth0") even when XDP is
enabled.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Static analysis tools report a problem from original driver submission.
Removing unnecessary check in condition.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set IFF_UNICAST_FLT flag for the VF to prevent it from entering
promiscuous mode when macvlan is added to the VF.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Caught by GCC 8. When we provide a length for strncpy, we should not
include the terminating null. So we must tell it one less than the size
of the destination buffer.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A PF can send any number of queues to the VF and the VF may not
be able to support that many. Check to see that the number of
queues is less than or equal to the max number of queues the
VF can have.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add possibility to change a VF mac address from host side
without reloading the VF driver on the guest side. Without
this patch it is not possible to change the VF mac because
executing i40evf_virtchnl_completion function with
VIRTCHNL_OP_GET_VF_RESOURCES opcode resets the VF mac
address to previous value.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a bug in the way we handled VF queues, by always showing stats for
the maximum number of queues, even if they aren't allocated. It is not
safe to change the number of strings reported to ethtool, as grabbing
statistics occurs over multiple ethtool ops for which the rtnl_lock()
cannot be held the entire time.
Avoid this by always reporting queue stats for the maximum number of
queues in the netdevice. Share some of the helper functionality for
adding stats with the PF code in i40e_ethtool_stats.h
This should reduce the chance of potential future bugs, and make adding
new statistics easier.
Note for the queue stats, unlike the PF driver we do not keep an array
of queue pointers, but an array of queues, so care must be taken to
avoid accessing queue memory that hasn't yet been allocated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Move the boiler plate structures and helper functions we recently
added into their own header file, so that the complete collection is
located together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use an i40e_stats array to handle the queue stats, instead of coding
similar functionality separately. Because of how the queue stats are
accessed on some kernels, we can't easily use i40e_add_ethtool_stats.
Instead, implement a separate helper, i40e_add_queue_stats, which we'll
use instead. This helper will correctly implement the
u64_stats_fetch_begin_irq logic and allow retries until successful. We
share the most complex code by re-using i40e_add_one_ethtool_stat.
This logic additionally easily supports skipping disabled rings by using
a ternary operator before calling the u64_stats_fetch_begin_irq()
function, so that we correctly zero-out the stats values without having
to perform two separate sections of code.
This significantly reduces the boiler plate code in
i40e_get_ethtool_stats, and helps keep the complex logic contained to as
few functions as possible.
With this patch, we've finally converted all the statistics to use the
helpers and the i40e_stats function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Johannes Berg says:
====================
Only a few changes at this point:
* new channels in 60 GHz
* clarify (average) ACK signal reporting API
* expose ieee80211_send_layer2_update() for all drivers
* start/stop mac80211's TXQs properly when required
* avoid regulatory restore with IE ignoring
* spelling: contidion -> condition
* fully implement WFA Multi-AP backhaul
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without a valid of_node in struct device we can't find the mvpp2 port
device by its DT node. Specifically, this breaks
of_find_net_device_by_node().
For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141
switch connected to the &cp1_eth2 port:
&cp1_mdio {
...
switch0: switch0@4 {
compatible = "marvell,mv88e6085";
...
ports {
...
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
};
};
};
};
Without this patch, dsa_register_switch() returns -EPROBE_DEFER because
of_find_net_device_by_node() can't find the device_node of the &cp1_eth2
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vxlan_find_mac() unconditionally set f->used for every packet,
this causes a cache miss for every packet, since remote, hlist
and used of vxlan_fdb share the same cache line, which are
accessed when send every packets.
so f->used is set only if not equal to jiffies, to reduce dirty
cache line times, this gives 3% speed-up with small packets.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Remove unused functions and data structures.
2. Change the sending of the remaining soft commands to synchronous.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Change struct octnic_ctrl_pkt to support synchronous operation.
2. Change code which use structure octnic_ctrl_pkt to send sc's
synchronously.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Add wait_for_sc_completion_timeout() for waiting the response and
handling common response errors
2. Send sc's synchronously: remove unused callback function,
and context structure; use wait_for_sc_completion_timeout() to wait
its response.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Sara Sharon
Emmanuel Grumbach
Erel Geron
Matt Chen
Johannes Berg
Mordechay Goodstein
Golan Ben Ami
Haim Dreyfuss
Ayala Beker
Liad Kaufman
Gregory Greenman
Luca Coelho
Shahar S Matityahu
Avraham Stern
Naftali Goldstein
Patryk Małek
Lihong Yang
Jan Sokolowski
Björn Töpel
Martyna Szapar
Mitch Williams
Paul M Stillwell Jr
Paweł Jabłoński
Jacob Keller
David S. Miller
Baruch Siach
Li RongQing
Felix Manlunas