aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2018-03-02iwlwifi: fix malformed CONFIG_IWLWIFI_PCIE_RTPM defaultUlf Magnusson1-1/+0
'default false' should be 'default n', though they happen to have the same effect here, due to undefined symbols ('false' in this case) evaluating to n in a tristate sense. Remove the default instead of changing it. bool and tristate symbols implicitly default to n. Discovered with the https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py script. Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: Correctly set the tid for mcast queueIlan Peer1-3/+3
In the scheduler config command, the meaning of tid == 0xf was intended to indicate the configuration is for management frames. However, tid == 0xf was also used for the multicast queue that was meant only for multicast data frames, which resulted with the FW not encrypting multicast data frames. As multicast frames do not have a QoS header, fix this by setting tid == 0, to indicate that this is a data queue and not management one. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: Direct multicast frames to the correct stationIlan Peer1-1/+5
Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were directed to the broadcast station, however, as the broadcast station did not have keys configured, these frames were sent unencrypted. Fix this by using the multicast station which is the station for which encryption keys are configured. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: fix "failed to remove key" messageSara Sharon1-1/+2
When the GTK is installed, we install it to HW with the station ID of the AP. Mac80211 will try to remove it only after the AP sta is removed, which will result in a failure to remove key since we do not have any station for it. This is a valid situation, but a previous commit removed the early return and added a return with error value, which resulted in an error message that is confusing to users. Remove the error return value. Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: avoid collecting firmware dump if not loadedShaul Triebitz5-5/+27
Trying to collect firmware debug data while firmware is not loaded causes various errors (e.g. failing NIC access). This causes even a bigger issue if at that time the HW radio is off. In that case, when later turning the radio on, the Driver fails to read the HW (registers contain garbage values). (It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN bit is cleared on faulty NIC access - since the same behavior was seen in HW RFKILL toggling before setting that bit.) Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: fix assert 0x2B00 on older FWsSara Sharon1-10/+35
We should add the multicast station before adding the broadcast station. However, in older FW, the firmware will start beaconing when we add the multicast station, and since the broadcast station is not added at this point so the transmission of the beacon will fail on assert 0x2b00. This is fixed in later firmware, so make the order of addition depend on the TLV. Fixes: 26d6c16bed53 ("iwlwifi: mvm: add multicast station") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: Fix channel switch for count 0 and 1Andrei Otcheretianski2-4/+6
It was assumed that apply_time==0 implies immediate scheduling, which is wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set. Otherwise, this resulted in 0x3063 assert. Fix that. While at it rename the T2_V2_START_IMMEDIATELY to TE_V2_START_IMMEDIATELY. Fixes: f5d8f50f271d ("iwlwifi: mvm: Fix channel switch in case of count <= 1") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: mvm: fix TX of CCMP 256Sara Sharon1-2/+5
We don't have enough room in the TX command for a CCMP 256 key, and need to use key from table. Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-02iwlwifi: Cancel and set MARKER_CMD timer during suspend-resumeHaim Dreyfuss4-0/+42
While entering to D3 mode there is a gap between the time the driver handles the D3_CONFIG_CMD response to the time the host is going to sleep. In between there might be cases which MARKER_CMD can tailgate. Also during resume flow the MARKER_CMD might get sent while D0I3_CMD is being handled in the FW. Cancel MARKER_CMD timer and set it again properly during suspend resume flows to prevent this command from being sent accidentlly. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-01net: phy: marvell10g: Utilize gen10g_no_soft_reset()Florian Fainelli1-10/+1
We do the same thing as the generic function: nothing, so utilize it. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-01net: phy: cortina: Utilize generic functionsFlorian Fainelli1-15/+3
cortina_soft_reset() does the same thing as gen10g_soft_reset(), and cortina_config_aneg() is actually doing what gen10g_config_init() does for 10G capable PHYs. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-01net: phy: teranetics: Utilize generic functionsFlorian Fainelli1-27/+5
Update teranetics_aneg_done() to use genphy_c45_aneg_done() instead of duplicating that code, and switch to gen10g_* functions where appropriate instead of maintaining identical copies doing nothing. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-01net: phy: Export gen10g_* functionsFlorian Fainelli1-7/+13
In order to remove a fair amount of duplication in the different 10G PHY drivers, export all gen10g_* functions to be able to make use of those. While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset() to illustrate what it does. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-01net: phy: aquantia: Utilize genphy_c45_aneg_done()Florian Fainelli1-14/+6
The driver duplicates what the generic function does, so use the generic function intead. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-03-01net/mac89x0: Replace custom debug logging with netif_* callsFinn Thain1-32/+15
Adopt the conventional style of debug logging because it is both shorter and more flexible. Remove the 'version_printed' flag as the version will be printed only once anyway (when the module loads). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01net/mac89x0: Fix and modernize log messagesFinn Thain1-10/+9
Fix log message fragments that no longer produce the desired output since the behaviour of printk() was changed. Add missing printk severity levels. Drop deprecated "out of memory" message as per checkpatch advice. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01net/mac89x0: Convert to platform_driverFinn Thain2-42/+29
Apparently these Dayna cards don't have a pseudoslot declaration ROM which means they can't be probed like NuBus cards. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01net/mac89x0: Remove redundant codeFinn Thain1-32/+0
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01net: phylink: Remove redundant netdev.phydev assignmentRichard Cochran1-2/+0
As a part of working on MII time stamping infrastructure, I was trying to figure out how netdev->phydev gets assigned, and I stumbled across this. Ever since the new phylink code came in, the field is assigned twice. The function, phylink_connect_phy(), calls phy_attach_direct() phylink_bringup_phy() and phy_attach_direct() sets dev->phydev = phydev; but phylink_bringup_phy() then sets the same field again: pl->netdev->phydev = phy; Similarly, the function, phylink_of_phy_connect(), calls of_phy_attach() phy_attach_direct() phylink_bringup_phy() The removal code is also duplicated: phylink_disconnect_phy() pl->netdev->phydev = NULL; phy_disconnect() phy_detach() phydev->attached_dev->phydev = NULL; This patch removes the redundant assignments, restricting manipulation of the netdev.phydev field to phy_attach_direct() and phy_detach(). Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-01ipmr, ip6mr: Make mfc_cache a common structureYuval Mintz1-10/+11
mfc_cache and mfc6_cache are almost identical - the main difference is in the origin/group addresses and comparison-key. Make a common structure encapsulating most of the multicast routing logic - mr_mfc and convert both ipmr and ip6mr into using it. For easy conversion [casting, in this case] mr_mfc has to be the first field inside every multicast routing abstraction utilizing it. Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28r8169: fix interrupt number after adding support for MSI-X interruptsHeiner Kallweit1-2/+3
In case of MSI-X the interrupt number may differ from pcidev->irq. Fix this by using pci_irq_vector(). Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28xen-netfront: Fix hang on device removalJason Andryuk1-1/+6
A toolstack may delete the vif frontend and backend xenstore entries while xen-netfront is in the removal code path. In that case, the checks for xenbus_read_driver_state would return XenbusStateUnknown, and xennet_remove would hang indefinitely. This hang prevents system shutdown. xennet_remove must be able to handle XenbusStateUnknown, and netback_changed must also wake up the wake_queue for that state as well. Fixes: 5b5971df3bc2 ("xen-netfront: remove warning when unloading module") Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Cc: Eduardo Otubo <otubo@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
2018-02-28{net, IB}/mlx5: Raise fatal IB event when sys error occursDaniel Jurgens1-1/+1
All other mlx5_events report the port number as 1 based, which is how FW reports it in the port event EQE. Reporting 0 for this event causes mlx5_ib to not raise a fatal event notification to registered clients due to a seemingly invalid port. All switch cases in mlx5_ib_event that go through the port check are supposed to set the port now, so just do it once at variable declaration. Fixes: 89d44f0a6c73("net/mlx5_core: Add pci error handlers to mlx5_core driver") Reviewed-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2018-02-28Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller6-20/+23
Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2018-02-28 This series contains updates to fm10k only. Jake provides all the changes in this series, starting with making the function header comments consistent and to align with how the kernel documentation expects it. Also cleaned up code comment as well as bump the driver version. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28spectrum: Reference count VLAN entriesIdo Schimmel2-1/+8
One of the basic construct in the device is a port-VLAN pair, which can be bound to a FID or a RIF in order to direct packets to the bridge or the router, respectively. Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs. sw1p1.10), VID 1 is used to represent these and thus this VID can be used by both upper devices of mlxsw ports and by the driver itself. However, this VID is not reference counted and therefore might be freed prematurely, which can result in various WARNINGs. For example: $ ip link add name br0 type bridge vlan_filtering 1 $ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}' $ ip link set dev team0 master br0 $ ip link set dev enp1s0np1 master team0 $ ip address add 192.0.2.1/24 dev enp1s0np1 The enslavement to team0 will fail because team0 already has an upper and thus vlan_vids_del_by_dev() will be executed as part of team's error path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The WARNING will be generated when the driver will realize it can't find VID 1 on the port and bind it to a RIF. Fix this by adding a reference count to the VLAN entries on the port, in a similar fashion to the reference counting used by the corresponding 'vlan_vid_info' structure in the 8021q driver. Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN") Reported-by: Tal Bar <talb@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Tested-by: Tal Bar <talb@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: Treat IPv6 unregistered multicast as broadcastIdo Schimmel1-1/+1
When multicast snooping is enabled, the Linux bridge resorts to flooding unregistered multicast packets to all ports only in case it did not detect a querier in the network. The above condition is not reflected to underlying drivers, which is especially problematic in IPv6 environments, as multicast snooping is enabled by default and since neighbour solicitation packets might be treated as unregistered multicast packets in case there is no corresponding MDB entry. Until the Linux bridge reflects its querier state to underlying drivers, simply treat unregistered multicast packets as broadcast and allow them to reach their destination. Fixes: 9df552ef3e21 ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: Fix handling of resource_size_paramJiri Pirko1-37/+38
Current code uses global variables, adjusts them and passes pointer down to devlink. With every other mlxsw_core instance, the previously passed pointer values are rewritten. Fix this by de-globalize the variables and also memcpy size_params during devlink resource registration. Also, introduce a convenient size_param_init helper. Fixes: ef3116e5403e ("mlxsw: spectrum: Register KVD resources with devlink") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: core: Fix flex keys scratchpad offset conflictJiri Pirko1-10/+10
IP_TTL, IP_ECN and IP_DSCP are using the same offset within the scratchpad as L4 ports. Fix this by shifting all up. Fixes: 5f57e0909136 ("mlxsw: acl: Add ip ttl acl element") Fixes: i80d0fe4710c ("mlxsw: acl: Add ip tos acl element") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28virtio-net: disable NAPI only when enabled during XDP setJason Wang1-3/+5
We try to disable NAPI to prevent a single XDP TX queue being used by multiple cpus. But we don't check if device is up (NAPI is enabled), this could result stall because of infinite wait in napi_disable(). Fixing this by checking device state through netif_running() before. Fixes: 4941d472bf95b ("virtio-net: do not reset during XDP set") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28ipvlan: use per device spinlock to protect addrs list updatesPaolo Abeni3-35/+56
This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28ipvlan: egress mcast packets are not exceptionalPaolo Abeni1-2/+2
Currently, if IPv6 is enabled on top of an ipvlan device in l3 mode, the following warning message: Dropped {multi|broad}cast of type= [86dd] is emitted every time that a RS is generated and dmseg is soon filled with irrelevant messages. Replace pr_warn with pr_debug, to preserve debuggability, without scaring the sysadmin. Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: prio: Handle graft commandNogah Frankel1-0/+54
Handle graft command for an offloaded sch_prio. Grafting a qdisc to any place other than under its original parent is not supported by mlxsw and will cause the grafted qdisc to stop being offloaded. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: prio: Delete child qdiscs when removing bandsNogah Frankel1-1/+6
When the number the bands of sch_prio is decreased, child qdiscs on the deleted bands would get deleted as well. This change and deletions are being done under sch_tree_lock of the sch_prio qdisc. Part of the destruction of qdisc is unoffloading it, if it is offloaded. Un-offloading can't be done inside this lock. Move the offload command to be done before reducing the number of bands, so unoffloading of the qdiscs that are about to be deleted could be done outside of the lock. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: Update sch_prio stats to include sch_red related dropsNogah Frankel1-1/+4
sch_prio as root qdisc should count all the drops its children have. Since it is possible for it to have sch_red children, it needs to count RED early drops. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: Update backlog handling of a child qdiscsNogah Frankel1-2/+12
When removing a child qdisc its backlog will be decreased from the parent backlog. The driver backlog count should do the same. When the parent changes its configuration, the child might need to clean its stats. However, the backlog can't be cleaned with the rest of the stats, because it reflects a momentary value that needs to be synced with the core, not the history of the qdisc. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: Collect stats for sch_red based on priomapNogah Frankel1-19/+50
Priority counters count packets according to their packet priority. Collect the stats for sch_red based on these counters, so the qdisc bstats will be the sum of counters matching the priorities marked in the qdisc priomap. Changing the mapping of the priorities to bands while traffic is running can result in losing the stats of the bands qdiscs from their last dump call to this change, as if the qdisc was unoffloaded and re-offloaded. It will not affect the traffic behaviour according to sch_red. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: Add priority map per qdiscNogah Frankel1-0/+7
Add priority map per qdisc, to indicate which priorities are being directed through this qdisc. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: Add priority countersNogah Frankel2-0/+12
Add TX packets and bytes counters per switch priority per port. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28mlxsw: spectrum: qdiscs: Support qdisc per tclassNogah Frankel2-10/+53
Add the option to set a qdisc per tclass. Match the qdisc to the tclass by parent ID. Supported currently for sch_red only. It allows offloading sch_prio as root qdisc and sch_red as its child. (However, doing so might corrupt the stats for both parent and child.) Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Yuval Mintz <yuvalm@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28net: mvpp2: Add hardware offloading for VLAN filteringMaxime Chevallier1-34/+380
Marvell PPv2 controller allows for generic packet filtering. This commit adds entries to implement VLAN filtering. The approach taken is : - Filter entries that would match on the presence of the VLAN tag (existing VLAN detection, DSA / EDSA detection) will set the next lookup ID to be for the VID. - For each VLAN existing on a given port, we add an entry that matches this specific VID. If the incoming packet matches the VID entry, it is set for the next lookup in the chain (LU_L2). - A Guard entry is added for each port, that will match if the incoming packet didn't match any of the above VID entries. This entry tags the packet to be dropped. Due to this design, and the fact that the total 256 filter entries are also used for other purposes, we have a limit of 10 VLANs per port. To accommodate the case where we would need more VLANS on one port, this patch implements the ndo_set_features to allow for disabling of VLAN filtering using ethtool. The default config has VLAN filtering disabled. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28r8169: convert remaining feature flag and remove enum featuresHeiner Kallweit1-8/+4
Now that only one feature flag is left we can convert it and remove enum features. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28net/macmace: Drop redundant MACH_IS_MAC testFinn Thain1-15/+1
The MACH_IS_MAC test is redundant here because the platform device won't get registered unless MACH_IS_MAC. Adopt module_platform_driver() convention. Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28net/macmace: Fix and clean up log messagesFinn Thain1-6/+3
Don't log the unexpanded "eth%d" format string. Log the chip revision in the probe message (consistent with mace.c). Drop redundant debug messages for FIFO events recorded in the interface statistics (also consistent with mace.c). Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28emulex/benet: Constify *be_misconfig_evt_port_state[]Hernán Gonzalez2-2/+2
Note: This is compile only tested as I have no access to the hw. No benefit gained except for some self-documenting. add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0) Function old new delta Total: Before=2757703, After=2757703, chg +0.00% Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28qlogic/qed: Constify *pkt_type_str[]Hernán Gonzalez1-1/+1
Note: This is compile only tested as I have no access to the hw. Constifying and declaring as static saves 24 bytes. add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-24 (-24) Function old new delta pkt_type_str 24 - -24 Total: Before=3599256, After=3599232, chg -0.00% Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar> Acked-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28sfp: add high power module supportJon Nettleton1-18/+132
This patch is the result of work by both Jon Nettleton and Russell King. Jon wrote the original patch, adding support for SFP modules which require a power level greater than '1'. Russell's changes: - Fix the power levels for big-endian, and make the code flow better. - Convert to use device_property_read_u8() - Warn for power levels exceeding host level SFF-8431 says: "To avoid exceeding system power supply limits and cooling capacity, all modules at power up by default shall operate with up to 1.0 W. Hosts supporting Power Level II or III operation may enable a Power Level II or III module through the 2-wire interface. Power Level II or III modules shall assert the power level declaration bit of SFF-8472." Print a warning for modules that exceed the host power level, and leave them operating in power level 1. - Fix i2c write The first byte of any write after the bus address is always the device address. In order to write a value to device D, address I, value V, we need to generate on the bus: S DDDDDDDD A IIIIIIII A VVVVVVVV A P where S = start, R = restart, A = ack, P = stop. Splitting this as two: S DDDDDDDD A IIIIIIII A R DDDDDDDD A VVVVVVVV A P results in the device's address register being written first by I and then by V - the addressed register within the device is not written. - Avoid power mode switching if 0xa2 is not implemented Some modules indicate that they support power level II or power level III, but do not implement address 0xa2, meaning that the bit to set them to high power mode is not accessible. These modules appear to have the sff8472_compliance field set to zero, and also do not implement diagnostics. Detect this, but also ensure that the module does not require the address switching mode, which we do not implement. - Use mW for power level rather than power level number. - Fix high power mode transition We must not switch to SFP_MOD_PRESENT state until we have finished initialising, because the remaining state machines check for that state. Add SFP_MOD_HPOWER as an intermediate state. - Use definition for I2C register address rather than constant. Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28phylink,sfp: negotiate interface format with MACRussell King2-76/+58
Negotiate the interface format with the MAC rather than requiring it to be a fixed type specified solely by the SFP module. This allows modules that can work with several different interface signalling formats to select a format compatible with the MAC - for example, a Fiber module supporing Gigabit ethernet and faster connected to a Gigabit only MAC needs to select the 1000BASE-X mode. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modulesRussell King1-23/+38
Some BiDi modules (eg, FiberStore SFP-GE-BX) are not compliant with 1000BASE-BX as they use different wavelengths from the 1000BASE-BX standard (eg, 1310nm/1550nm rather than 1310nm/1490nm). These modules support 1000BASE-X ethernet, so detect them by a failure to find any other support, the 8B10B encoding and a bit rate that falls within the 1Gbps window. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28team: Use extack to report enslavement failuresIdo Schimmel1-5/+11
Use extack inside team's enslavement function and also propagate it to the netdevice notifier to allow enslaved ports to report the failure reason. Example: $ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}' $ ip link set dev lo master team0 Error: Loopback device can't be added as a team port. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28gianfar: Fix Rx byte accounting for ndev statsClaudiu Manoil1-4/+3
Don't include in the Rx bytecount of the packet sent up the stack: the FCB (frame control block), and the padding bytes inserted by the controller into the frame payload, nor the FCS. All these are being pulled out of the skb by gfar_process_frame(). This issue is old, likely from the driver's beginnings, however it was amplified by recent: commit d903ec77118c ("gianfar: simplify FCS handling and fix memory leak") which basically added the FCS to the Rx bytecount, and so brought this to my attention. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.