| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit fbf3d034f2ff6264183cfa6845770e8cc2a986c8.
As of commit 560869100b99a3da ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both tx_ring and first_tx are the head of tx ring, it not
necessary to use two structure members to statically indicate
the head of tx ring. So first_tx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the requested dump level parameter to big-endian at the start of
nfp_net_dump_calculate_size() and nfp_net_dump_populate_buffer(), then
compare and assign it directly where needed in the traversal and prolog
code. This decreases the total number of conversions used.
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete match field defines that are not supported at this time.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port matching is selected by default on every rule so remove check for it
and delete 'else' side of the statement. Remove nfp_flower_meta_one as now
it will not feature in the code. Rename nfp_flower_meta_two given that one
has been removed.
'Additional metadata' if statement can never be true so remove it as well.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the matching of mac/mpls as a default selection. These are not
necessarily set by a TC rule (unlike the port). Previously a mac/mpls
field would exist in every match and be masked out if not used. This patch
has no impact on functionality but removes unnessary memory assignment in
the match cmsg.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all variants of the sh_eth hardware have Gigabit
support. Unfortunately, the current driver doesn't tell the PHY about
the limited MAC capabilities. Due to this, if you have a Gigabit
capable PHY, the PHY will advertise its Gigabit capability and
establish a link at 1Gbit/s, even though the MAC doesn't support it.
In order to avoid this, we use the recently introduced
phy_set_max_speed() to tell the PHY to not advertise speed higher than
100 MBit/s.
Tested on a SH7786 platform, with a Gigabit PHY.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
Fixes: 7334b3e47aee ("net: phy: Add Meson GXL Internal PHY driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets that don't have dest mac as the mac of the master device should
not be entertained by the IPvlan rx-handler. This is mostly true as the
packet path mostly takes care of that, except when the master device is
a virtual device. As demonstrated in the following case -
ip netns add ns1
ip link add ve1 type veth peer name ve2
ip link add link ve2 name iv1 type ipvlan mode l2
ip link set dev iv1 netns ns1
ip link set ve1 up
ip link set ve2 up
ip -n ns1 link set iv1 up
ip addr add 192.168.10.1/24 dev ve1
ip -n ns1 addr 192.168.10.2/24 dev iv1
ping -c2 192.168.10.2
<Works!>
ip neigh show dev ve1
ip neigh show 192.168.10.2 lladdr <random> dev ve1
ping -c2 192.168.10.2
<Still works! Wrong!!>
This patch adds that missing check in the IPvlan rx-handler.
Reported-by: Amit Sikka <amit.sikka@ericsson.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:
- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
the driver is expected to retrieve that from ieee80211_next_txq()
- Two new mac80211 functions are added: ieee80211_next_txq() and
ieee80211_schedule_txq(). The former returns the next TXQ that should be
scheduled, and is how the driver gets a queue to pull packets from. The
latter is called internally by mac80211 to start scheduling a queue, and
the driver is supposed to call it to re-schedule the TXQ after it is
finished pulling packets from it (unless the queue emptied).
The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll,
only if PS_ENABLED was set before.
This is required due to commit c9491367b759 ("mac80211: always update the
PM state of a peer on MGMT / DATA frames") that enforces the ap to
check only mgmt/data frames ps bit, and then update station's power save
accordingly.
When sending only ps-poll (control frame) the ap will not be aware that
the station entered power save.
Setting ps enable before triggering ps_poll, will send NDP with PM bit
enabled first.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflict was two parallel additions of include files to sch_generic.c,
no biggie.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
drivers).
2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
to userspace and broke some apps. From Johannes Berg.
3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
Wang.
4) Gianfar MAC can't do EEE so don't advertise it by default, from
Claudiu Manoil.
5) Relax strict netlink attribute validation, but emit a warning. From
David Ahern.
6) Fix regression in checksum offload of thunderx driver, from Florian
Westphal.
7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.
8) New card support in iwlwifi, from Ihab Zhaika.
9) BBR congestion control bug fixes from Neal Cardwell.
10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.
11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.
12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.
13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
net: mvpp2: fix the RSS table entry offset
tcp: evaluate packet losses upon RTT change
tcp: fix off-by-one bug in RACK
tcp: always evaluate losses in RACK upon undo
tcp: correctly test congestion state in RACK
bnxt_en: Fix sources of spurious netpoll warnings
tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
tcp_bbr: reset full pipe detection on loss recovery undo
tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
sfc: pass valid pointers from efx_enqueue_unwind
gianfar: Disable EEE autoneg by default
tcp: invalidate rate samples during SACK reneging
can: peak/pcie_fd: fix potential bug in restarting tx queue
can: usb_8dev: cancel urb on -EPIPE and -EPROTO
can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
can: esd_usb2: cancel urb on -EPIPE and -EPROTO
can: ems_usb: cancel urb on -EPIPE and -EPROTO
can: mcba_usb: cancel urb on -EPROTO
usbnet: fix alignment for frames with no ethernet header
tcp: use current time in tcp_rcv_space_adjust()
...
|
|
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
|
|
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-08
this is a pull request of 6 patches for net/master.
Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first and only parameter of sl_alloc() is unused, so remove it.
Fixes: 5342b77c4123 slip: ("Clean up create and destroy")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79fb4 ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to identify TX and RX payload regions and skip them in
collection of EDC, MC, and HMA.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use meminfo to get base address and size of MC memory. Also use same
meminfo for EDC memory dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect memory layout of various on-chip memory regions. Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function. Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef99 ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ALR table operations are a sequence of related register operations which
should be protected from concurrent access. The alr_cache should also be
protected. Add alr_mutex doing that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After applying 2270bc5da3497945 ("bnxt_en: Fix netpoll handling") and
903649e718f80da2 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099ea ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 39e6c8208d7b ("net: solve a NAPI race") napi has been able
to be rescheduled within napi_complete_done() even in non-busypoll case,
but virtnet_poll() always enabled interrupts before complete, and when
napi was rescheduled within napi_complete_done() it did not disable
interrupts.
This caused more interrupts when event idx is disabled.
According to commit cbdadbbf0c79 ("virtio_net: fix race in RX VQ
processing") we cannot place virtqueue_enable_cb_prepare() after
NAPI_STATE_SCHED is cleared, so disable interrupts again if
napi_complete_done() returned false.
Tested with vhost-user of OVS 2.7 on host, which does not have the event
idx feature.
* Before patch:
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32763206 0 6430.32
212992 60.00 23384299 4589.56
Interrupts on guest: 9872369
Packets/interrupt: 2.37
* After patch
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32794646 0 6436.49
212992 60.00 32793501 6436.27
Interrupts on guest: 4941299
Packets/interrupt: 6.64
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Private destructor could be called when register_netdev() fail with
rtnl lock held. This will lead deadlock in tun_free_netdev() who tries
to hold rtnl_lock. Fixing this by switching to use spinlock to
synchronize.
Fixes: 96f84061620c ("tun: add eBPF based queue selection method")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file. Fix that to use CONFIG
instead.
Fixes: 9f66a397c877 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Second batch of iwlwifi updates for v4.16
* Initial work for rate-scaling offload;
* Support for new FW API version;
* Some fixes here and there;
|
|
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Richard Leitner
Geert Uytterhoeven
Antoine Tenart
Yan Markman
Zhu Yanjun
Carl Heymann
John Hurley
Thomas Petazzoni
Jerome Brunet
Mahesh Bandewar
Tom Herbert
Toke Høiland-Jørgensen
Adiel Aloni
David S. Miller
Linus Torvalds
Marc Kleine-Budde
Rahul Lakkireddy
Stephen Hemminger
Niklas Cassel
Egil Hjelmeland
Calvin Owens
Bert Kenward
Claudiu Manoil
Toshiaki Makita
Jason Wang
Jérémy Lefaure
Luca Coelho
Kalle Valo
Stephane Grosjean
Martin Kelly
Bjørn Mork