| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Data centric bridging designed to eliminate packet loss due to
queue overflow by adding enhancements to ethernet network such as
proprity flow control etc. This patch adds support for management
of Priority flow control(PFC) on Octeontx2 and CN10K interfaces.
To enable PFC for all priorities
dcb pfc set dev eth0 prio-pfc all:on/off
To enable PFC on selected priorites
dcb pfc set dev eth0 prio-pfc 0:on/off 1:on/off ..7:on/off
With the ntuple commands user can map Priority to receive queues.
On queue overflow NIX will assert backpressure such that PFC pause frames
are genarated with mapped priority.
To map priority 7 to Queue 1
ethtool -U eth0 flow-type ether dst xx:xx:xx:xx:xx:xx vlan 0xe00a
m 0x1fff queue 1
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10K MAC block (RPM) and Octeontx2 MAC block (CGX) both supports
PFC flow control and 802.3X flow control pause frames.
Each MAC block supports max 4 LMACS and AF driver assigns same
(MAC,LMAC) to PF and its VFs. As PF and its share same (MAC,LMAC)
pair we need resource management to address below scenarios
1. Maintain PFC and 8023X pause frames mutually exclusive.
2. Reject disable flow control request if other PF or Vfs
enabled it.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prirority based flow control (802.1Qbb) mechanism is similar to
ethernet pause frames (802.3x) instead pausing all traffic on a link,
PFC allows user to selectively pause traffic according to its class.
Oceteontx2 MAC block (CGX) and CN10K Mac block (RPM) both supports
PFC. As upper layer mbox handler is same for both the MACs, this
patch configures PFC by calling apporopritate callbacks.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation is such that 802.3x pause frames are
enabled by default. As CGX and RPM blocks support PFC
(priority flow control) also, instead of driver enabling one
between them enable them upon request from PF or its VFs.
Also add support to disable pause frames in driver unbind.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Hardware interrupts are enabled during the pci probe, however,
they are not disabled during pci removal.
Disable all hardware interrupts during pci removal to avoid any
issues.
Fixes: e75377404726 ("amd-xgbe: Update PCI support to use new IRQ functions")
Suggested-by: Selwin Sebastian <Selwin.Sebastian@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix loading of the driver when built as a module.
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
veth being NETIF_F_LLTX enabled, we need to be more careful
whenever we read/write rq->rx_notify_masked.
BUG: KCSAN: data-race in veth_xmit / veth_xmit
write to 0xffff888133d9a9f8 of 1 bytes by task 23552 on cpu 0:
__veth_xdp_flush drivers/net/veth.c:269 [inline]
veth_xmit+0x307/0x470 drivers/net/veth.c:350
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
NF_HOOK include/linux/netfilter.h:307 [inline]
br_forward_finish net/bridge/br_forward.c:66 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
__br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
br_dev_xmit+0x8b6/0x960
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
neigh_hh_output include/net/neighbour.h:525 [inline]
neigh_output include/net/neighbour.h:539 [inline]
ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:451 [inline]
ip_local_out net/ipv4/ip_output.c:126 [inline]
ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888133d9a9f8 of 1 bytes by task 23563 on cpu 1:
__veth_xdp_flush drivers/net/veth.c:268 [inline]
veth_xmit+0x2d6/0x470 drivers/net/veth.c:350
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
br_dev_queue_push_xmit+0x3ce/0x430 net/bridge/br_forward.c:53
NF_HOOK include/linux/netfilter.h:307 [inline]
br_forward_finish net/bridge/br_forward.c:66 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
__br_forward+0x2e4/0x400 net/bridge/br_forward.c:115
br_flood+0x521/0x5c0 net/bridge/br_forward.c:242
br_dev_xmit+0x8b6/0x960
__netdev_start_xmit include/linux/netdevice.h:4683 [inline]
netdev_start_xmit include/linux/netdevice.h:4697 [inline]
xmit_one+0x105/0x2f0 net/core/dev.c:3473
dev_hard_start_xmit net/core/dev.c:3489 [inline]
__dev_queue_xmit+0x86d/0xf90 net/core/dev.c:4116
dev_queue_xmit+0x13/0x20 net/core/dev.c:4149
neigh_hh_output include/net/neighbour.h:525 [inline]
neigh_output include/net/neighbour.h:539 [inline]
ip_finish_output2+0x6f8/0xb70 net/ipv4/ip_output.c:228
ip_finish_output+0xfb/0x240 net/ipv4/ip_output.c:316
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip_output+0xf3/0x1a0 net/ipv4/ip_output.c:430
dst_output include/net/dst.h:451 [inline]
ip_local_out net/ipv4/ip_output.c:126 [inline]
ip_send_skb+0x6e/0xe0 net/ipv4/ip_output.c:1570
udp_send_skb+0x641/0x880 net/ipv4/udp.c:967
udp_sendmsg+0x12ea/0x14c0 net/ipv4/udp.c:1254
inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg net/socket.c:725 [inline]
____sys_sendmsg+0x39a/0x510 net/socket.c:2413
___sys_sendmsg net/socket.c:2467 [inline]
__sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
__do_sys_sendmmsg net/socket.c:2582 [inline]
__se_sys_sendmmsg net/socket.c:2579 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 23563 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00064-gc36c04c2e132 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 948d4f214fde ("veth: Add driver XDP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2022-02-08
Joe Damato says:
This patch set makes several updates to the i40e driver stats collection
and reporting code to help users of i40e get a better sense of how the
driver is performing and interacting with the rest of the kernel.
These patches include some new stats (like waived and busy) which were
inspired by other drivers that track stats using the same nomenclature.
The new stats and an existing stat, rx_reuse, are now accessible with
ethtool to make harvesting this data more convenient for users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netvsc_device_remove() calls vunmap() inside which should not be
called in the interrupt context. Current code calls hv_unmap_memory()
in the free_netvsc_device() which is rcu callback and maybe called
in the interrupt context. This will trigger BUG_ON(in_interrupt())
in the vunmap(). Fix it via moving hv_unmap_memory() to netvsc_device_
remove().
Fixes: 846da38de0e8 ("net: netvsc: Add Isolation VM support for netvsc driver")
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2022-02-07
Corinna Vinschen says:
Fix the kernel warning "Missing unregister, handled but fix driver"
when running, e.g.,
$ ethtool -G eth0 rx 1024
on igc. Remove memset hack from igb and align igb code to igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT
that gets set if nfp_flower_is_supported_bridge is true is not taken
into account. Consequently the path that should release the ida_index
in cleanup is never triggered, causing messages like:
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to
new tunnel flows not being offloaded.
Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if
the port is of type OTHER.
Fixes: 2e0bc7f3cb55 ("nfp: flower: encode mac indexes with pre-tunnel rule check")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LiteX driver uses devm io function API which
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: ee7da21ac4c3 ("net: Add driver for LiteX's LiteETH network interface")
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220208013308.6563-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
cleanup_net() is competing with other rtnl users.
Batching bond_net_exit() factorizes all rtnl acquistions
to a single one, giving chance for cleanup_net()
to progress much faster, holding rtnl a bit longer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If __ibmvnic_open() encounters an error such as when setting link state,
it calls release_resources() which frees the napi structures needlessly.
Instead, have __ibmvnic_open() only clean up the work it did so far (i.e.
disable napi and irqs) and leave the rest to the callers.
If caller of __ibmvnic_open() is ibmvnic_open(), it should release the
resources immediately. If the caller is do_reset() or do_hard_reset(),
they will release the resources on the next reset.
This fixes following crash that occurred when running the drmgr command
several times to add/remove a vnic interface:
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[6] irq
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[7] irq
[102056] ibmvnic 30000003 env3: Replenished 8 pools
Kernel attempted to read user page (10) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000010
Faulting instruction address: 0xc000000000a3c840
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
CPU: 9 PID: 102056 Comm: kworker/9:2 Kdump: loaded Not tainted 5.16.0-rc5-autotest-g6441998e2e37 #1
Workqueue: events_long __ibmvnic_reset [ibmvnic]
NIP: c000000000a3c840 LR: c0080000029b5378 CTR: c000000000a3c820
REGS: c0000000548e37e0 TRAP: 0300 Not tainted (5.16.0-rc5-autotest-g6441998e2e37)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28248484 XER: 00000004
CFAR: c0080000029bdd24 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0
GPR00: c0080000029b55d0 c0000000548e3a80 c0000000028f0200 0000000000000000
...
NIP [c000000000a3c840] napi_enable+0x20/0xc0
LR [c0080000029b5378] __ibmvnic_open+0xf0/0x430 [ibmvnic]
Call Trace:
[c0000000548e3a80] [0000000000000006] 0x6 (unreliable)
[c0000000548e3ab0] [c0080000029b55d0] __ibmvnic_open+0x348/0x430 [ibmvnic]
[c0000000548e3b40] [c0080000029bcc28] __ibmvnic_reset+0x500/0xdf0 [ibmvnic]
[c0000000548e3c60] [c000000000176228] process_one_work+0x288/0x570
[c0000000548e3d00] [c000000000176588] worker_thread+0x78/0x660
[c0000000548e3da0] [c0000000001822f0] kthread+0x1c0/0x1d0
[c0000000548e3e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
7d2948f8 792307e0 4e800020 60000000 3c4c01eb 384239e0 f821ffd1 39430010
38a0fff6 e92d1100 f9210028 39200000 <e9030010> f9010020 60420000 e9210020
---[ end trace 5f8033b08fd27706 ]---
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220208001918.900602-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 803.2ad mode enables a participating port, it should update
the slave-array. I have observed that the member links are participating
and are part of the active aggregator while the traffic is egressing via
only one member link (in a case where two links are participating). Via
kprobes I discovered that slave-arr has only one link added while
the other participating link wasn't part of the slave-arr.
I couldn't see what caused that situation but the simple code-walk
through provided me hints that the enable_port wasn't always associated
with the slave-array update.
Fixes: ee6377147409 ("bonding: Simplify the xmit function for modes that use xmit_hash")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220207222901.1795287-1-maheshb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This caused a significant performance degredation when using generic XDP
with multiple queues.
Fixes: f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Tao Liu <xliutaox@google.com>
Link: https://lore.kernel.org/r/20220207175901.2486596-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This NIC does not support TSO, it is very unlikely it would
have to send packets with many fragments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220208004855.1887345-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nguyen, Anthony L says:
====================
iwl-next Intel Wired LAN Driver Updates 2022-02-07
Dave adds support for ice driver to provide DSCP QoS mappings to irdma
driver.
[1] https://lore.kernel.org/netdev/20220202191921.1638-1-shiraz.saleem@intel.com/
* 'iwl-next' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/linux:
ice: add support for DSCP QoS for IDC
====================
Link: https://lore.kernel.org/r/20220207235921.1303522-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In some cases, pages cannot be reused by i40e because the page is busy. Add
a counter for this event.
Busy page count is accessible via ethtool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In some cases, pages can not be reused because they are not associated with
the correct NUMA zone. Knowing how often pages are waived helps users to
understand the interaction between the driver's memory usage and their
system.
Pass rx_stats through to i40e_can_reuse_rx_page to allow tracking when
pages are waived.
The page waive count is accessible via ethtool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a counter for new page allocations in the i40e RX path. This stat is
accessible with ethtool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
rx page reuse was already being tracked by the i40e driver per RX ring.
Aggregate the counts and make them accessible via ethtool.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Page reuse was being tracked from two locations:
- i40e_reuse_rx_page (via 40e_clean_rx_irq), and
- i40e_alloc_mapped_page
Remove the double count and only count reuse from i40e_alloc_mapped_page
when the page is about to be reused.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Reading the PTP clock is a simple operation requiring only 3 register
reads. Under a PREEMPT_RT kernel, protecting those reads by a spin_lock is
counter-productive: if the 2nd task preempting the 1st has a higher prio
but needs to read time as well, it will require 2 context switches, which
will pretty much always be more costly than just disabling preemption for
the duration of the reads. Moreover, with the code logic recently added
to get_systime(), disabling preemption is not even required anymore:
reads and writes just need to be protected from each other, to prevent a
clock read while the clock is being updated.
Improve the above situation by replacing the PTP spinlock by a rwlock, and
using read_lock for PTP clock reads so simultaneous reads do not block
each other.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20220204135545.2770625-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We need this to get vxlan_features_check() definition.
Fixes: d2692eee05b8 ("net: typhoon: implement ndo_features_check method")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220208003502.1799728-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
Fixes: 9cbc948b5a20c ("igb: add XDP support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Calling ethtool changing the RX ring parameters like this:
$ ethtool -G eth0 rx 1024
on igc triggers kernel warnings like this:
[ 225.198467] ------------[ cut here ]------------
[ 225.198473] Missing unregister, handled but fix driver
[ 225.198485] WARNING: CPU: 7 PID: 959 at net/core/xdp.c:168
xdp_rxq_info_reg+0x79/0xd0
[...]
[ 225.198601] Call Trace:
[ 225.198604] <TASK>
[ 225.198609] igc_setup_rx_resources+0x3f/0xe0 [igc]
[ 225.198617] igc_ethtool_set_ringparam+0x30e/0x450 [igc]
[ 225.198626] ethnl_set_rings+0x18a/0x250
[ 225.198631] genl_family_rcv_msg_doit+0xca/0x110
[ 225.198637] genl_rcv_msg+0xce/0x1c0
[ 225.198640] ? rings_prepare_data+0x60/0x60
[ 225.198644] ? genl_get_cmd+0xd0/0xd0
[ 225.198647] netlink_rcv_skb+0x4e/0xf0
[ 225.198652] genl_rcv+0x24/0x40
[ 225.198655] netlink_unicast+0x20e/0x330
[ 225.198659] netlink_sendmsg+0x23f/0x480
[ 225.198663] sock_sendmsg+0x5b/0x60
[ 225.198667] __sys_sendto+0xf0/0x160
[ 225.198671] ? handle_mm_fault+0xb2/0x280
[ 225.198676] ? do_user_addr_fault+0x1eb/0x690
[ 225.198680] __x64_sys_sendto+0x20/0x30
[ 225.198683] do_syscall_64+0x38/0x90
[ 225.198687] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 225.198693] RIP: 0033:0x7f7ae38ac3aa
igc_ethtool_set_ringparam() copies the igc_ring structure but neglects to
reset the xdp_rxq_info member before calling igc_setup_rx_resources().
This in turn calls xdp_rxq_info_reg() with an already registered xdp_rxq_info.
Make sure to unregister the xdp_rxq_info structure first in
igc_setup_rx_resources.
Fixes: 73f1071c1d29 ("igc: Add support for XDP_TX action")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Call mv88e6xxx_reg_unlock(chip) before returning on this error path.
Fixes: 7af4a361a62f ("net: dsa: mv88e6xxx: Improve isolation of standalone ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The <= ARRAY_SIZE() needs to be < ARRAY_SIZE() to prevent an out of
bounds error.
Fixes: d4ebf12bcec4 ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the device that supports the TX push capability, the BD can
be directly copied to the device memory. However, due to hardware
restrictions, the push mode can be used only when there are no
more than two BDs, otherwise, the doorbell mode based on device
memory is used.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8168d_2_hw_phy_config() shares quite some functionality with
rtl8168d_1_hw_phy_config(), so let's factor out the common part to a
new function rtl8168d_1_common(). In addition improve the code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv6 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv4 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add fields related to SIP_DIP_ACTION, which is used for changing of SIP
and DIP addresses.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of disabling TSO at compile time if MAX_SKB_FRAGS > 32,
implement ndo_features_check() method for this driver for
a more dynamic handling.
If skb has more than 32 frags and is a GSO packet, force
software segmentation.
Most locally generated packets will use a small number
of fragments anyway.
For forwarding workloads, we can limit gro_max_size at ingress,
we might also implement gro_max_segs if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems this one-element array is not actually being used as an
array of variable size, so we can just replace it with just a
non-array object of type struct desc_frag and refactor a bit the
rest of the code.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The filters for the PTP trap keys are incorrectly configured, in the
sense that is2_entry_set() only looks at trap->key.ipv4.dport or
trap->key.ipv6.dport if trap->key.ipv4.proto or trap->key.ipv6.proto is
set to IPPROTO_TCP or IPPROTO_UDP.
But we don't do that, so is2_entry_set() goes through the "else" branch
of the IP protocol check, and ends up installing a rule for "Any IP
protocol match" (because msk is also 0). The UDP port is ignored.
This means that when we run "ptp4l -i swp0 -4", all IP traffic is
trapped to the CPU, which hinders bridging.
Fix this by specifying the IP protocol in the VCAP IS2 filters for PTP
over UDP.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch statement already ensures cqe_type == CQE_RX_OKAY at that
point.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Hariprasad Kelam
Sunil Kumar Kori
Uwe Kleine-König
Raju Rangoju
Joel Stanley
Eric Dumazet
David S. Miller
Tianyu Lan
Louis Peens
Cai Huoqing
Sukadev Bhattiprolu
Vladimir Oltean
Mahesh Bandewar
Tao Liu
Jakub Kicinski
Joe Damato
Yannick Vignon
Pavel Parkhomenko
Corinna Vinschen
Dan Carpenter
Yufeng Mo
Pavel Skripkin
Heiner Kallweit
Danielle Ratson
Gustavo A. R. Silva
Haiyang Zhang