| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The management frame with high rate e.g. 24M may not be transmitted
smoothly in long range environment.
Add a debugfs to force to use the lowest basic rate
in order to debug the reachability of transmitting management frame.
obtain current setting
cat /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
force lowest rate:
echo 1 > /sys/kernel/debug/ieee80211/phyX/rtw88/force_lowest_basic_rate
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-2-pkshih@realtek.com
|
|
By default the driver uses the 1M and 6M rate for managemnt frames
in 2G and 5G bands respectively. But when the basic rates is
configured from the mac80211, we need to send the management frames
according to the basic rates.
This commit makes the driver use the lowest basic rates to send
the management frames.
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211102022454.10944-1-pkshih@realtek.com
|
|
The AXIDMA is tx/rx packet transmission between PCIE host
and device, and TX FIFO is MAC TX data.
We dump them to verify that these memory buffers are correct.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211122021129.4339-1-pkshih@realtek.com
|
|
The RF register array is used to help firmware to restore RF settings.
The original code can potentially access out of range, if the size is
between (RTW89_H2C_RF_PAGE_SIZE * RTW89_H2C_RF_PAGE_NUM + 1) to
((RTW89_H2C_RF_PAGE_SIZE + 1) * RTW89_H2C_RF_PAGE_NUM). Fortunately,
current used size doesn't fall into the wrong case, and the size will not
change if we don't update RF parameter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119055729.12826-1-pkshih@realtek.com
|
|
Fix the following coccicheck review:
./drivers/net/wireless/realtek/rtw89/mac.c: 1096: 5-8: Unneeded variable
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211110121135.151187-1-deng.changcheng@zte.com.cn
|
|
The conditional operator is unnecessary while assigning values to the
bool variables.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104061119.1685-1-ye.guojin@zte.com.cn
|
|
Start to configure entries with RTW89_QATAR, RTW89_UKRAINE, RTW89_CN.
Adjust some entries with explicit rtw89_regulatory instead of RTW89_WW.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-5-pkshih@realtek.com
|
|
Update tx power limit table and tx power limit_ru table to R54.
Configure entries for MEXICO, CN, QATAR, and adjust some values
of original entries.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-4-pkshih@realtek.com
|
|
Support QATAR in rtw89_regulation_type and reorder the enum to align
realtek R58-R31 regulation definition. Besides, if an unassigned entry
of limit/limit_ru tables is read, return the corresponding WW value for
the unconfigured case.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-3-pkshih@realtek.com
|
|
This modification just replaces the number filled in the regd field
with the corresponding enum. No assignment of a value in a table is
changed. Doing this first is because the follow-up patches may adjust
the order of enum declarations.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211101093106.28848-2-pkshih@realtek.com
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_after() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct.
Additionally fix the common helper, ieee80211_tx_info_clear_status(),
which was not clearing ack_signal, but the open-coded versions
did. Johannes Berg points out this bug was introduced by commit
e3e1a0bcb3f1 ("mac80211: reduce IEEE80211_TX_MAX_RATES") but was harmless.
Also drops the associated unneeded BUILD_BUG_ON()s, and adds a note to
carl9170 about usage.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com> [both CARL9170+P54USB on real HW]
Link: https://lore.kernel.org/r/20211118203839.1289276-1-keescook@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since firmware uses its own sequence number counters, we need to
use firmware number as well when mac80211 generates the ADD_BA
request packet. Indeed the firmware sequence counters tend to
slightly drift from the mac80211 ones because of firmware offload
features like ARP responses. This causes the starting sequence
number field of the ADD_BA request to be unaligned, and can possibly
cause issues with strict/picky APs.
To fix this, we retrieve the current firmware sequence number for
a given TID through the smd_trigger_ba API, and use that number as
replacement of the mac80211 starting sequence number.
This change also ensures that any issue in the smd *ba procedures
will cause the ba action to properly fail, and remove useless call
to smd_trigger_ba() from IEEE80211_AMPDU_RX_START.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637604251-11763-1-git-send-email-loic.poulain@linaro.org
|
|
CE interrupt configuration uses host ce parameters to assign/free
interrupts. Use host ce parameters to enable/disable interrupts.
This patch fixes below BUG,
BUG: KASAN: global-out-of-bounds in 0xffffffbffdfb035c at addr
ffffffbffde6eeac
Read of size 4 by task kworker/u8:2/132
Address belongs to variable ath11k_core_qmi_firmware_ready+0x1b0/0x5bc [ath11k]
OOB is due to ath11k_ahb_ce_irqs_enable() iterates ce_count(which is 12)
times and accessing 12th element in target_ce_config
(which has only 11 elements) from ath11k_ahb_ce_irq_enable().
With this change host ce configs are used to enable/disable interrupts.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00471-QCAHKSWPL_SILICONZ-1
Fixes: 967c1d1131fa ("ath11k: move target ce configs to hw_params")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249558-12793-1-git-send-email-akolli@codeaurora.org
|
|
IPA v4.2 introduced GSI channel flow control, used instead of IPA
endpoint DELAY mode to prevent a TX channel from injecting packets
into the IPA core. It used a new FLOW_CONTROLLED channel state
which could be entered using GSI generic commands.
IPA v4.11 extended the channel flow control model. Rather than
having a distinct FLOW_CONTROLLED channel state, each channel has a
"flow control" property that can be enabled or not--independent of
the channel state. The AP (or modem) can modify this property using
the same GSI generic commands as before.
The AP only uses channel flow control on modem TX channels, and only
when recovering from a modem crash. The AP has no way to discover
the state of a modem channel, so the fact that (starting with IPA
v4.11) flow control no longer uses a distinct channel state is
invisible to the AP. So enhanced flow control generally does not
change the way AP uses flow control.
There are a few small differences, however:
- There is a notion of "primary" or "secondary" flow control, and
when enabling or disabling flow control that must be specified
in a new field in the GSI generic command register. For now, we
always specify 0 (meaning "primary").
- When disabling flow control, it's possible a request will need
to be retried. We retry up to 5 times in this case.
- Another new generic command allows the current flow control
state to be queried. We do not use this.
Other than the need for retries, the code essentially works the same
way as before.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
One quirk for certain versions of IPA is that endpoint DELAY mode
does not work properly. IPA DELAY mode prevents any packets from
being delivered to the IPA core for processing on a TX endpoint.
The AP uses DELAY mode when the modem crashes, to prevent modem TX
endpoints from generating traffic during crash recovery. Without
this, there is a chance the hardware will stall during recovery from
a modem crash.
To achieve a similar effect, a GSI FLOW_CONTROLLED channel state
was created. A STARTED TX channel can be placed in FLOW_CONTROLLED
state, which prevents the transfer of any more packets. A channel
in FLOW_CONTROLLED state can be either returned to STARTED state, or
can be transitioned to STOPPED state.
Because this operates on GSI channels, two generic commands were
added to allow the AP to control this state for modem channels
(similar to the ALLOCATE and HALT channel commands).
Previously the code assumed this quirk only applied to IPA v4.2.
In fact, channel flow control (rather than endpoint DELAY mode)
should be used for all versions *starting* with IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jiri assures me that a ldisc->open with tty->disc_data set should never
happen, so this check doesn't do anything.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current serial driver requires a maximum MTU of 68, and it doesn't
make sense to set a MTU below the MCTP-required baseline (of 68) either.
This change sets the min_mtu & max_mtu of the mctp netdev, essentially
disallowing changes. By using these instead of a ndo_change_mtu op, we
get the netlink extacks reported too.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to ensure that the tx work has finished before returning from
the ldisc close op, so do a synchronous cancel.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dummy net_device is a large field in the GSI structure, but it
is not at all interesting from the perspective of debugging. Move
it to the end of the GSI structure so the other fields are easier to
find in memory.
The channel and event ring arrays are also very large, so move them
near the end of the structure as well.
Swap the position of the result and completion fields to improve
structure packing.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A mutex ensures we never submit more than one GSI command of any
kind at once. This means the per-channel and per-event ring
completion structures provide no benefit. Instead, just use the
single (existing) GSI completion to signal the completion of GSI
commands of all types.
This makes gsi_evt_ring_init() a trivial function with no inverse,
so open-code it in its sole caller and get rid of the function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ipa_endpoint_skb_copy(), a new socket buffer structure is
allocated so that some data can be copied into it. However, after
doing this, if the endpoint has a null netdev pointer, we just drop
free the socket buffer.
Instead, check endpoint->netdev pointer first, and just return early
if it's null. Also return early if the SKB allocation fails, to
avoid the deeper indentation in the normal path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During setup, ipa_endpoint_program() programs each endpoint with
various configuration parameters. One of those registers defines
whether to drop packets when a head-of-line blocking condition is
detected on an RX endpoint. We currently assume this is disabled;
instead, explicitly set it to be disabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The head-of-line block (HOLB) drop timer is only meaningful when
dropping packets due to blocking is enabled. Given that, redefine
the interface so the timer is specified when enabling HOLB drop, and
use a different function when disabling.
To enable and disable HOLB drop, these functions will now be used:
ipa_endpoint_init_hol_block_enable(endpoint, milliseconds)
ipa_endpoint_init_hol_block_disable(endpoint)
The existing ipa_endpoint_init_hol_block_enable() becomes a helper
function, renamed ipa_endpoint_init_hol_block_en(), and used with
ipa_endpoint_init_hol_block_timer() to enable HOLB block on an
endpoint.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Not all filter table entries are used. Only certain endpoints
support filtering, and the table begins with a bitmap indicating
which endpoints use the "slots" that follow for filter rules.
Currently, unused filter table entries are not initialized.
Instead, zero-fill the entire unused portion of the filter table
memory regions, to make it more obvious that memory is unused (and
not subsequently modified).
This is not strictly necessary, but the result is reassuring when
looking at filter table memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A recent commit made disabling the SMP2P "setup ready" interrupt
unrelated to ipa_modem_stop(). Given that, it seems fitting to get
rid of ipa_modem_init() and ipa_modem_exit() (which are trivial
wrapper functions), and call ipa_smp2p_init() and ipa_smp2p_exit()
directly instead.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only called takes ocelot_port->bridge and passes it as the "bridge"
argument to this function, which then compares it with
ocelot_port->bridge. This is not useful.
Instead, we would like this function to return 0 if ocelot_port->bridge
is not present, which is what this patch does.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in a netdev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211125002932.49217-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When XDP program is loaded, it is desirable that the previous TX and RX
coalesce values are not re-inited to its default value. This prevents
unnecessary re-configurig the coalesce values that were working fine
before.
Fixes: ac746c8520d9 ("net: stmmac: enhance XDP ZC driver level switching performance")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211124114019.3949125-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The node pointer is returned by of_get_child_by_name() with
refcount incremented in tsnep_mdio_init(). Calling of_node_put()
to aovid the refcount leak in tsnep_mdio_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211124084048.175456-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
use ethtools api ethtool_sprintf to instead of snprintf.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Link: https://lore.kernel.org/r/20211125025444.13115-1-xiangxia.m.yue@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Populate the supported interfaces bitmap and MAC capabilities mask for
the macb driver and remove the old validate implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mpuRv-00D4rb-Lz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It seems only XID 609 made it to the mass market. Therefore let's
disable detection of the other RTL8125a XID's. If nobody complains
we can remove support for RTL_GIGA_MAC_VER_60 later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2cd3df01-5f8b-08dd-6def-3f31a3014bde@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the previous patches, noone needs 'file' parameter in neither
ioctl hook from tty_ldisc_ops. So remove 'file' from both of them.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> [NFC]
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122094529.24171-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes: f160e99462c6 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes: 16eb8815c235 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3de5 ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix warning reported by bot.
Make sure hash is init to 0 and fix wrong logic for hash_type in
qca8k_lag_can_offload.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: def975307c01 ("net: dsa: qca8k: add LAG support")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211123154446.31019-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Even if firmware fails to recognize the plugged-in port module type,
allow reading port module EEPROM anyway. This helps in obtaining
necessary diagnostics information for debugging and analysis.
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/1637682437-31407-1-git-send-email-rahul.lakkireddy@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All gro_complete() handlers are called from napi_gro_complete()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All gro_receive() handlers are called from dev_gro_receive()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following warning is fixed, by removing the unused resource size:
drivers/net/ethernet/engleder/tsnep_main.c:1155:21-24:
WARNING: Suspicious code. resource_size is maybe missing with io
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20211124205225.13985-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove .owner field if calls are used which set it automatically
Eliminate the following coccicheck warning:
./drivers/net/ethernet/engleder/tsnep_main.c:1263:3-8: No need to set
.owner here. The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/1637721384-70836-2-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 816625c13652cef5b2c49082d652875da6f2ad7a.
Attempts to validate length in the core did not work out.
We'll drop them, so revert the dependent changes in drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Fix a possible idr pkt-id leak if the packet is dropped on tx side
Fixes: bd1e3e7b693c ("mt76: introduce packet_id idr")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/a560caffcc24452fb48af53904bbe5c45ea5db93.1637602268.git.lorenzo@kernel.org
|
|
Should keep SKBs only if timeout timestamp is still after jiffies.
Otherwise, report tx status and drop it direclty.
Fixes: bd1e3e7b693c ("mt76: introduce packet_id idr")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/7e3784949c0b29a00465966b89fdb0192bd0298e.1637593492.git.deren.wu@mediatek.com
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() so memset() doesn't get confused about writing
beyond the destination member that is intended to be the starting point
of zeroing through the end of the struct. Additionally split up a later
field-spanning memset() so that memset() can reason about the size.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118202416.1286046-1-keescook@chromium.org
|
|
There is a spelling mistake in an ath11k_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211123090431.165103-1-colin.i.king@gmail.com
|
Yu-Yen Ting
Chia-Yuan Li
Ping-Ke Shih
Changcheng Deng
Ye Guojin
Zong-Zhe Yang
Kees Cook
Loic Poulain
Anilkumar Kolli
Alex Elder
Jeremy Kerr
Vladimir Oltean
Colin Ian King
Ong Boon Leong
Yang Yingliang
Tonghao Zhang
Russell King (Oracle)
Heiner Kallweit
Jiri Slaby
Dylan Hung
Jesse Brandeburg
Ansuel Smith
Rahul Lakkireddy
Eric Dumazet
Gerhard Engleder
Yang Li
Michael S. Tsirkin
Lorenzo Bianconi
Deren Wu