aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2021-10-20net/mlx5e: IPsec: Fix a misuse of the software parser's fieldsEmeel Hakim1-24/+27
IPsec crypto offload current Software Parser (SWP) fields settings in the ethernet segment (eseg) are not aligned with PRM/HW expectations. Among others in case of IP|ESP|TCP packet, current driver sets the offsets for inner_l3 and inner_l4 although there is no inner l3/l4 headers relative to ESP header in such packets. SWP provides the offsets for HW ,so it can be used to find csum fields to offload the checksum, however these are not necessarily used by HW and are used as fallback in case HW fails to parse the packet, e.g when performing IPSec Transport Aware (IP | ESP | TCP) there is no need to add SW parse on inner packet. So in some cases packets csum was calculated correctly , whereas in other cases it failed. The later faced csum errors (caused by wrong packet length calculations) which led to lots of packet drops hence the low throughput. Fix by setting the SWP fields as expected in a IP|ESP|TCP packet. the following describe the expected SWP offsets: * Tunnel Mode: * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP IP L4 * * Transport Mode: * SWP: OutL3 OutL4 * Pkt: MAC IP ESP L4 * * Tunnel(VXLAN TCP/UDP) over Transport Mode * SWP: OutL3 InL3 InL4 * Pkt: MAC IP ESP UDP VXLAN IP L4 Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload") Signed-off-by: Emeel Hakim <ehakim@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5e: Fix vlan data lost during suspend flowMoshe Shemesh3-12/+26
During suspend flow the driver calls mlx5e_destroy_vlan_table() which does not only delete the vlans steering flow rules, but also frees the data on currently active vlans, thus it is not restored during resume flow. This fix keeps the vlan data on suspend flow and frees it only on driver remove flow. Fixes: 6783f0a21a3c ("net/mlx5e: Dynamic alloc vlan table for netdev when needed") Signed-off-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5: E-switch, Return correct error code on group creation failureDmytro Linkin1-4/+3
Dan Carpenter report: The patch f47e04eb96e0: "net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups" from May 31, 2021, leads to the following Smatch static checker warning: drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group() warn: passing zero to 'ERR_PTR' If min rate normalization failed then error code may be overwritten to 0 if scheduling element destruction succeed. Ignore this value and always return initial one. Fixes: f47e04eb96e0 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20net/mlx5: Lag, change multipath and bonding to be mutually exclusiveMaor Dickman5-5/+18
Both multipath and bonding events are changing the HW LAG state independently. Handling one of the features events while the other is already enabled can cause unwanted behavior, for example handling bonding event while multipath enabled will disable the lag and cause multipath to stop working. Fix it by ignoring bonding event while in multipath and ignoring FIB events while in bonding mode. Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-20Merge tag 'mt76-for-kvalo-2021-10-20' of https://github.com/nbd168/wirelessKalle Valo70-2537/+6107
mt76 patches for 5.16 * various bugfixes * endian fixes * mt7921 aspm support * cleanup * mt7921 testmode support * rate handling fixes * tx status fixes/improvements * mt7921 power management improvements * mt7915 LED support * DBDC fixes * mt7921 6GHz support * support for eeprom data in DT * mt7915 TWT support * mt7915 txbf + MU-MIMO improvements # gpg: Signature made Wed 20 Oct 2021 12:24:46 PM EEST # gpg: using DSA key D77D141D02A76EF5 # gpg: Good signature from "Felix Fietkau <nbd@nbd.name>" [unknown] # gpg: WARNING: This key is not certified with a trusted signature! # gpg: There is no indication that the signature belongs to the owner. # Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
2021-10-20ice: Add missing E810 device idsTony Nguyen3-0/+8
As part of support for E810 XXV devices, some device ids were inadvertently left out. Add those missing ids. Fixes: 195fb97766da ("ice: add additional E810 device id") Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
2021-10-20igc: Update I226_K device IDSasha Neftin1-1/+1
The device ID for I226_K was incorrectly assigned, update the device ID to the correct one. Fixes: bfa5e98c9de4 ("igc: Add new device ID") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20e1000e: Fix packet loss on Tiger Lake and laterSasha Neftin2-1/+13
Update the HW MAC initialization flow. Do not gate DMA clock from the modPHY block. Keeping this clock will prevent dropped packets sent in burst mode on the Kumeran interface. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377 Fixes: fb776f5d57ee ("e1000e: Add support for Tiger Lake") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Mark Pearson <markpearson@lenovo.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20e1000e: Separate TGP board type from SPTSasha Neftin3-23/+46
We have the same LAN controller on different PCHs. Separate TGP board type from SPT which will allow for specific fixes to be applied for TGP platforms. Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Mark Pearson <markpearson@lenovo.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20net: stmmac: Fix E2E delay mechanismKurt Kanzenbach1-1/+1
When utilizing End to End delay mechanism, the following error messages show up: |root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m |ptp4l[950.573]: selected /dev/ptp3 as PTP clock |ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE |ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1 |ptp4l[956.879]: selected best master clock 001395.fffe.4897b4 |ptp4l[956.879]: port 1: assuming the grand master role |ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER |ptp4l[962.017]: port 1: received DELAY_REQ without timestamp |ptp4l[962.273]: port 1: received DELAY_REQ without timestamp |ptp4l[963.090]: port 1: received DELAY_REQ without timestamp Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") already addresses this problem for the dwmac v5.10. However, same holds true for all dwmacs above version v4.10. Correct the check accordingly. Afterwards everything works as expected. Tested on Intel Atom(R) x6414RE Processor. Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2") Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a") Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20phy: micrel: ksz8041nl: do not use power down modeStefan Agner1-2/+3
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using the power down mode bit (0.11). If the PHY is taken out of power down mode in a certain temperature range, the PHY enters a weird state which leads to continuously reporting RX errors. In that state, the MAC is not able to receive or send any Ethernet frames and the activity LED is constantly blinking. Since Linux is using the suspend callback when the interface is taken down, ending up in that state can easily happen during a normal startup. Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal clock recovery when using power down mode. Even the latest revision (A4, Revision ID 0x1513) seems to suffer that problem, and according to the errata is not going to be fixed. Remove the suspend/resume callback to avoid using the power down mode completely. [*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs") Signed-off-by: Stefan Agner <stefan@agner.ch> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: enetc: unmap DMA in enetc_send_cmd()Tim Gardner1-7/+11
Coverity complains of a possible dereference of a null return value. 5. returned_null: kzalloc returns NULL. [show details] 6. var_assigned: Assigning: si_data = NULL return value from kzalloc. 488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL); 489 cbd.length = cpu_to_le16(data_size); 490 491 dma = dma_map_single(&priv->si->pdev->dev, si_data, 492 data_size, DMA_FROM_DEVICE); While this kzalloc() is unlikely to fail, I did notice that the function returned without unmapping si_data. Fix this by refactoring the error paths and checking for kzalloc() failure. Fixes: 888ae5a3952ba ("net: enetc: add tc flower psfp offload driver") Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: dsa: qca8k: tidy for loop in setup and add cpu port checkAnsuel Smith1-30/+44
Tidy and organize qca8k setup function from multiple for loop. Change for loop in bridge leave/join to scan all port and skip cpu port. No functional change intended. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller17-286/+764
Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2021-10-19 This series contains updates to ice driver only. Brett implements support for ndo_set_vf_rate allowing for min_tx_rate and max_tx_rate to be set for a VF. Jesse updates DIM moderation to improve latency and resolves problems with reported rate limit and extra software generated interrupts. Wojciech moves a check for trusted VFs to the correct function, disables lb_en for switchdev offloads, and refactors ethtool ops due to differences in support for PF and port representor support. Cai Huoqing utilizes the helper function devm_add_action_or_reset(). Gustavo A. R. Silva replaces uses of allocation to devm_kcalloc() as applicable. Dan Carpenter propagates an error instead of returning success. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: via-velocity: use eth_hw_addr_set()Jakub Kicinski1-1/+3
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: via-rhine: use eth_hw_addr_set()Jakub Kicinski1-1/+3
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: tlan: use eth_hw_addr_set()Jakub Kicinski1-4/+6
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Read the address into an array on the stack, do the swapping, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: tehuti: use eth_hw_addr_set()Jakub Kicinski1-2/+4
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Break the address up into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: stmmac: use eth_hw_addr_set()Jakub Kicinski1-2/+6
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20ethernet: netsec: use eth_hw_addr_set()Jakub Kicinski1-6/+8
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: disable sriov before unload hclge layerPeng Li3-0/+23
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko. hns3.ko includes network stack and pci_driver, hclge.ko includes HW device action, algo_ops and timer task, hnae3.ko includes some register function. When SRIOV is enable and hclge.ko is removed, HW device is unloaded but VF still exists, PF will not reply VF mbx messages, and cause errors. This patch fix it by disable SRIOV before remove hclge.ko. Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix vf reset workqueue cannot exitYufeng Mo1-3/+3
The task of VF reset is performed through the workqueue. It checks the value of hdev->reset_pending to determine whether to exit the loop. However, the value of hdev->reset_pending may also be assigned by the interrupt function hclgevf_misc_irq_handle(), which may cause the loop fail to exit and keep occupying the workqueue. This loop is not necessary, so remove it and the workqueue will be rescheduled if the reset needs to be retried or a new reset occurs. Fixes: 1cc9bc6e5867 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: schedule the polling again when allocation failsYunsheng Lin1-10/+12
Currently when there is a rx page allocation failure, it is possible that polling may be stopped if there is no more packet to be reveiced, which may cause queue stall problem under memory pressure. This patch makes sure polling is scheduled again when there is any rx page allocation failure, and polling will try to allocate receive buffers until it succeeds. Now the allocation retry is added, it is unnecessary to do the rx page allocation at the end of rx cleaning, so remove it. And reset the unused_count to zero after calling hns3_nic_alloc_rx_buffers() to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under memory pressure. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix for miscalculation of rx unused descYunsheng Lin2-0/+9
rx unused desc is the desc that need attatching new buffer before refilling to hw to receive new packet, the number of desc need attatching new buffer is calculated using next_to_use and next_to_clean. when next_to_use == next_to_clean, currently hns3 driver assumes that all the desc has the buffer attatched, but 'next_to_use == next_to_clean' also means all the desc need attatching new buffer if hw has comsumed all the desc and the driver has not attatched any buffer to the desc yet. This patch adds 'refill' in desc_cb to indicate whether a new buffer has been refilled to a desc. Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: fix the max tx size according to user manualYunsheng Lin2-9/+4
Currently the max tx size supported by the hw is calculated by using the max BD num supported by the hw. According to the hw user manual, the max tx size is fixed value for both non-TSO and TSO skb. This patch updates the max tx size according to the manual. Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: add limit ets dwrr bandwidth cannot be 0Guangbin Huang1-0/+9
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP mode. In this case, this tc may occupy all the tx bandwidth if it has huge traffic, so it violates the purpose of the user setting. To fix this problem, limit the ets dwrr bandwidth must greater than 0. Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: reset DWRR of unused tc to zeroGuangbin Huang1-0/+2
Currently, DWRR of tc will be initialized to a fixed value when this tc is enabled, but it is not been reset to 0 when this tc is disabled. It cause a problem that the DWRR of unused tc is not 0 after using tc tool to add and delete multi-tc parameters. For examples, after enabling 4 TCs and restoring to 1 TC by follow tc commands: $ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \ 8@0 8@8 8@16 8@24 hw 1 mode channel $ tc qdisc del dev eth0 root Now there is just one TC is enabled for eth0, but the tc info querying by debugfs is shown as follow: $ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info enabled tc number: 1 weight_offset: 14 TC MODE WEIGHT 0 dwrr 100 1 dwrr 100 2 dwrr 100 3 dwrr 100 4 dwrr 0 5 dwrr 0 6 dwrr 0 7 dwrr 0 This patch fixes it by resetting DWRR of tc to 0 when tc is disabled. Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: hns3: Add configuration of TM QCN error eventJiaran Zhang2-1/+6
Add configuration of interrupt type and fifo interrupt enable of TM QCN error event if enabled, otherwise this event will not be reported when there is error. Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delaysVladimir Oltean3-47/+107
This change does not fix any functional issue or address any real life use case that wasn't possible before. It is just a small step in the process of standardizing the way in which Ethernet MAC drivers may apply RGMII delays (traditionally these have been applied by PHYs, with no clear definition of what to do in the case of a fixed-link). The sja1105 driver used to apply MAC-level RGMII delays on the RX data lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or "rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id". But the standard definitions don't say anything about behaving differently when the port is in fixed-link vs when it isn't, and the new device tree bindings are about having a way of applying the delays in a way that is independent of the phy-mode and of the fixed-link property. When the {rx,tx}-internal-delay-ps properties are present, use them, otherwise fall back to the old behavior and warn. One other thing to note is that the SJA1105 hardware applies a delay value in degrees rather than in picoseconds (the delay in ps changes depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at 100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase shift of the internal delay lines assuming that the device tree meant gigabit, and we let the hardware scale those according to the link speed. Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/ Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123 Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20vrf: Revert "Reset skb conntrack connection..."Eugene Crosser1-4/+0
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1. When an interface is enslaved in a VRF, prerouting conntrack hook is called twice: once in the context of the original input interface, and once in the context of the VRF interface. If no special precausions are taken, this leads to creation of two conntrack entries instead of one, and breaks SNAT. Commit above was intended to avoid creation of extra conntrack entries when input interface is enslaved in a VRF. It did so by resetting conntrack related data associated with the skb when it enters VRF context. However it breaks netfilter operation. Imagine a use case when conntrack zone must be assigned based on the original input interface, rather than VRF interface (that would make original interfaces indistinguishable). One could create netfilter rules similar to these: chain rawprerouting { type filter hook prerouting priority raw; iif realiface1 ct zone set 1 return iif realiface2 ct zone set 2 return } This works before the mentioned commit, but not after: zone assignment is "forgotten", and any subsequent NAT or filtering that is dependent on the conntrack zone does not work. Here is a reproducer script that demonstrates the difference in behaviour. ========== #!/bin/sh # This script demonstrates unexpected change of nftables behaviour # caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack # connection on VRF rcv" # https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1 # # Before the commit, it was possible to assign conntrack zone to a # packet (or mark it for `notracking`) in the prerouting chanin, raw # priority, based on the `iif` (interface from which the packet # arrived). # After the change, # if the interface is enslaved in a VRF, such # assignment is lost. Instead, assignment based on the `iif` matching # the VRF master interface is honored. Thus it is impossible to # distinguish packets based on the original interface. # # This script demonstrates this change of behaviour: conntrack zone 1 # or 2 is assigned depending on the match with the original interface # or the vrf master interface. It can be observed that conntrack entry # appears in different zone in the kernel versions before and after # the commit. IPIN=172.30.30.1 IPOUT=172.30.30.2 PFXL=30 ip li sh vein >/dev/null 2>&1 && ip li del vein ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf nft list table testct >/dev/null 2>&1 && nft delete table testct ip li add vein type veth peer veout ip li add tvrf type vrf table 9876 ip li set veout master tvrf ip li set vein up ip li set veout up ip li set tvrf up /sbin/sysctl -w net.ipv4.conf.veout.accept_local=1 /sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0 ip addr add $IPIN/$PFXL dev vein ip addr add $IPOUT/$PFXL dev veout nft -f - <<__END__ table testct { chain rawpre { type filter hook prerouting priority raw; iif { veout, tvrf } meta nftrace set 1 iif veout ct zone set 1 return iif tvrf ct zone set 2 return notrack } chain rawout { type filter hook output priority raw; notrack } } __END__ uname -rv conntrack -F ping -W 1 -c 1 -I vein $IPOUT conntrack -L Signed-off-by: Eugene Crosser <crosser@average.org> Acked-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-20zd1201: use eth_hw_addr_set()Jakub Kicinski1-3/+4
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-16-kuba@kernel.org
2021-10-20wl3501_cs: use eth_hw_addr_set()Jakub Kicinski1-2/+1
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-15-kuba@kernel.org
2021-10-20ray_cs: use eth_hw_addr_set()Jakub Kicinski1-1/+1
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-14-kuba@kernel.org
2021-10-20wilc1000: use eth_hw_addr_set()Jakub Kicinski2-5/+11
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-13-kuba@kernel.org
2021-10-20hostap: use eth_hw_addr_set()Jakub Kicinski1-1/+4
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-11-kuba@kernel.org
2021-10-20ipw2200: prepare for const netdev->dev_addrJakub Kicinski2-4/+4
netdev->dev_addr will be come const soon, constify the argument to command send to avoid compiler warnings. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-10-kuba@kernel.org
2021-10-20airo: use eth_hw_addr_set()Jakub Kicinski1-14/+13
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Use dev_addr_set() to match the existing logic. setup_card() is always passed netdev->dev_addr, so pass the netdev pointer instead and assign the address using a helper there. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-9-kuba@kernel.org
2021-10-20brcmfmac: prepare for const netdev->dev_addrJakub Kicinski1-2/+2
netdev->dev_addr will become const soon. Make sure local variables maintain that qualifier. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-8-kuba@kernel.org
2021-10-20atmel: use eth_hw_addr_set()Jakub Kicinski1-5/+10
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Use a buffer on the stack. Note that atmel_get_mib() is a wrapper around atmel_copy_to_host(). For the to device direction we just need to make sure functions respect argument being cost. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-7-kuba@kernel.org
2021-10-20wil6210: use eth_hw_addr_set()Jakub Kicinski3-5/+7
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Do the special encoding on the stack, then copy the address. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-6-kuba@kernel.org
2021-10-20ath6kl: use eth_hw_addr_set()Jakub Kicinski1-4/+5
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Do the special encoding on the stack, then copy the address. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-5-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set() for dev->addr_len casesJakub Kicinski2-2/+2
Convert all WiFi drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) Manually checked the netdevs are allocated with alloc_etherdev(), so dev->addr_len must be equal to ETH_ALEN. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-4-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set() instead of ether_addr_copy()Jakub Kicinski4-7/+7
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Convert wireless from ether_addr_copy() to eth_hw_addr_set(): @@ expression dev, np; @@ - ether_addr_copy(dev->dev_addr, np) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-3-kuba@kernel.org
2021-10-20wireless: use eth_hw_addr_set()Jakub Kicinski11-20/+18
Convert all WiFi drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, ETH_ALEN) + eth_hw_addr_set(dev, np) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211018235021.1279697-2-kuba@kernel.org
2021-10-20iwlwifi: cfg: set low-latency-xtal for some integrated So devicesJohannes Berg1-1/+1
The integrated So devices covered by the iwl_so_long_latency_trans_cfg configuration should all have low-latency-xtal enabled, so do that. While at it, remove the TODO, I've checked the other values as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 6f60fb03c8e7 ("iwlwifi: move SnJ and So rules to the new tables") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.8b5480113f53.I80b5b4ebea84e56f3b3143fc1ee7097be8b4ae78@changeid
2021-10-20iwlwifi: pnvm: read EFI data only if long enoughJohannes Berg1-3/+7
If the data we get from EFI is not even long enough for the package struct we expect then ignore it entirely. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: a1a6a4cf49ec ("iwlwifi: pnvm: implement reading PNVM from UEFI") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.33feba783518.I54a5cf33975d0330792b3d208b225d479e168f32@changeid
2021-10-20iwlwifi: pnvm: don't kmemdup() more than we haveJohannes Berg1-4/+3
We shouldn't kmemdup() more data than we have, that might cause the code to crash. Fix that by updating the length before the kmemdup. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.ab0e64c3fba9.Ic6a3295fc384750b51b4270bf0b7d94984a139f2@changeid
2021-10-20iwlwifi: change all JnP to NO-160 configurationYaara Baruch1-3/+3
JnP should not have the 160 MHz. Signed-off-by: Yaara Baruch <yaara.baruch@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.ee163f4a7513.I7f87bd969a0b038c7f3a1a962d9695ffd18c5da1@changeid
2021-10-20iwlwifi: mvm: reset PM state on unsuccessful resumeJohannes Berg1-1/+4
If resume fails for some reason, we need to set the PM state back to normal so we're able to send commands during firmware reset, rather than failing all of them because we're in D3. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: 708a39aaca22 ("iwlwifi: mvm: don't send commands during suspend\resume transition") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20211016114029.7ceb9eaca9f6.If0cbef38c6d07ec1ddce125878a4bdadcb35d2c9@changeid
2021-10-20Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo22-60/+224
ath.git patches for v5.16. Major changes: ath9k * add option to reset the wifi chip via debugfs * convert Device Tree bindings to the json-schema * support Device Tree ieee80211-freq-limit property to limit channels
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.