| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it. And I think the 'Jensen' actually
did have an ISA slot.
However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':
outl((int) (skb->data), ioaddr + Wn7_MasterAddr);
which is all kinds of broken. Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits. I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".
Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).
Who knows, this might even work.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In __iwl_mvm_remove_time_event() check that 'te_data->vif' is NULL
before dereferencing it.
Fixes: 7b3954a1d69a ("iwlwifi: mvm: Explicitly stop session protection before unbinding")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210907143156.e80e52167d93.Ie2247f43f8acb2cee6dff5b07a3947c79a772835@changeid
|
|
On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The devlink parameters are not the right mechanism to pass
extra parameters to device flashing. The params added are
also undocumented.
This reverts commit 13bb8429ca98 ("net: wwan: iosm: firmware
flashing and coredump collection").
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets. This problem state
will happen if three specific conditions occur:
1) driver has received more than (N * RxRingSize) packets but
less than (N+1 * RxRingSize) packets, where N is an odd number
Note: the command "ethtool -g <interface>" will display the
current receive ring size, which currently defaults to 128
2) the driver's interface was disabled via "ifconfig oob_net0 down"
during the window described in #1.
3) the driver's interface is re-enabled via "ifconfig oob_net0 up"
This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware. Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.
Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN10K MAC block (RPM) differs in number of stats compared to Octeontx2
MAC block (CGX). RPM supports stats for each class of PFC and error
packets etc. It would be difficult for user to read stats from ethtool
and map to their definition.
New debugfs file is already added to read RPM stats along with their
definition. This patch adds proper checks such that RPM stats will not
be part of ethtool.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff3679 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was used but never set. The hardcoded value from before the dawn of
time was non-standard; the usual name for cross-tools is $TRIPLET-$TOOL
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, and simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.
Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
|
|
Survey dump statistics is not displaying channel rx and tx time because
the service flag is not enabled. Enable the service flag "bss_chan_info"
in wmi_resource_config to fetch and print the stats for the specific
pdev.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-2-jouni@codeaurora.org
|
|
The flag's purpose is not only meant for ATF configs. Rename atf_config
to flag1, so it can be used for future purposes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-1-jouni@codeaurora.org
|
|
In 4addr, AP wired backbone to STA wired backbone ping fails due to ARP
request not getting answered. Here 4addr ARP multicast packet is sent in
3addr, so that 4addr STA not honouring the 3addr ARP multicast packet.
Fix this issue by sending out multicast packet in 4addr format, firmware
expects peer meta flag instead of vdev meta flag in Tx descriptor.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01641-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-2-jouni@codeaurora.org
|
|
Ath11k FW requires peer parameter WMI_PEER_USE_4ADDR to be set for
4-addr peers allowing 4-address frame transmission to those peers.
Add ath11k driver callback for sta_set_4addr() to queue new workq
set_4addr_wk only once based on new boolean, use_4addr_set.
sta_set_4addr() will be called during 4-addr STA association cases
applicable for both AP and STA modes.
In ath11k_sta_set_4addr_wk(),
AP mode:
WMI_PEER_USE_4ADDR will be set for the corresponding
associated 4-addr STA(s)
STA mode:
WMI_PEER_USE_4ADDR will be set for the AP to which the
4-addr STA got associated.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-1-jouni@codeaurora.org
|
|
extends the owl loader to fetch important pci initialization
values - which are stored together with the calibration data -
through the nvmem subsystem.
This allows for much faster WIFI/ath9k initializations on devices
that do not require to perform any post-processing (like XOR'ing/
reversal or unpacking)... than the current way through the
firmware_request which involves the filesystem/userspace.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/bc79ba1c6f6435000577bf1e5f4d7ebe18a8df97.1630157099.git.chunkeey@gmail.com
|
|
On most embedded ath9k devices (like range extenders,
routers, accesspoints, ...) the calibration data is
stored in a MTD partitions named "ART", or "caldata"/
"calibration".
Since commit 4b361cfa8624 ("mtd: core: add OTP nvmem provider support"):
All MTD partitions are all automatically available through
the nvmem subsystem.
This feature - together with an nvmem cell definition either
in the platform data or via device-tree allows drivers to get
the data necessary for initializing the WIFI, without having
to wait around for the filesystem and userspace to do
the extractions.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f9b732b50a3453fadf3923cc75d365bae3505fe7.1630157099.git.chunkeey@gmail.com
|
|
This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Fixes: 3ac8eed62596 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement support for ethtool_ops::reset in order to reset transceiver
modules. The module backing the netdev is reset when the 'ETH_RESET_PHY'
flag is set. After a successful reset, the flag is cleared by the driver
and other flags are ignored. This is in accordance with the interface
documentation:
"The reset() operation must clear the flags for the components which
were actually reset. On successful return, the flags indicate the
components which were not reset, either because they do not exist in the
hardware or because they cannot be reset independently. The driver must
never reset any components that were not requested."
Reset is useful in order to allow a module to transition out of a fault
state. From section 6.3.2.12 in CMIS 5.0: "Except for a power cycle, the
only exit path from the ModuleFault state is to perform a module reset
by taking an action that causes the ResetS transition signal to become
TRUE (see Table 6-11)".
An error is returned when the netdev is administratively up:
# ip link set dev swp11 up
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
# ip link set dev swp11 down
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Components reset: 0x40
An error is returned when the module is shared by multiple ports (split
ports) and the "phy-shared" flag is not set:
# devlink port split swp11 count 4
# ethtool --reset swp11s0 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
# ethtool --reset swp11s0 phy-shared
ETHTOOL_RESET 0x400000
Components reset: 0x400000
# devlink port unsplit swp11s0
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Components reset: 0x40
An error is also returned when one of the ports using the module is
administratively up:
# devlink port split swp11 count 4
# ip link set dev swp11s1 up
# ethtool --reset swp11s0 phy-shared
ETHTOOL_RESET 0x400000
Cannot issue ETHTOOL_RESET: Invalid argument
# ip link set dev swp11s1 down
# ethtool --reset swp11s0 phy-shared
ETHTOOL_RESET 0x400000
Components reset: 0x400000
Reset is performed by writing to the "rst" bit of the PMAOS register,
which instructs the firmware to assert the reset signal connected to the
module for a fixed amount of time.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PMAOS register has enable bits (e.g., PMAOS.ee) that allow changing
only a subset of the fields, which is exactly what subsequent patches
will need to do. Instead of passing multiple arguments to its pack
function, only pass the module index and let the rest be set by the
different callers.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ports Module Administrative and Operational Status (PMAOS) register
configures and retrieves the per-module status. Extend it with fields
required to support various module settings such as reset and power
mode.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the common port module core, track the number of logical ports that
are mapped to the port module and the number of logical ports using it
that are administratively up.
This will be used by later patches to potentially veto and control
certain operations on the module, such as reset and setting its power
mode.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value is never checked. Allows us to simplify a later patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value is not checked by the networking stack. Allows us to
simplify a later patch.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous patch, the lock is always taken in process context so
it can be converted to a mutex. It is needed for future changes where we
will need to be able to sleep when holding the lock.
Convert the lock to a mutex.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Module temperature events are currently handled in softIRQ context,
requiring the 'module_info_lock' to be a spin lock. In future patchsets
we will need to be able to hold the lock while sleeping.
Therefore, defer handling of these events using a work queue so that the
next patch will be able to convert the lock to a mutex.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous patch, the switch driver is always initialized last,
making this function redundant.
Remove it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 961cf99a074f ("mlxsw: core: Re-order initialization sequence")
changed the initialization sequence so that the switch driver (e.g.,
mlxsw_spectrum) is initialized before registration with the hwmon and
thermal subsystems.
This was done in order to avoid situations where hwmon/thermal code uses
features not supported by current firmware version, which is only
validated as part of switch driver initialization.
Later, commit b79cb787ac70 ("mlxsw: Move fw flashing code into core.c")
moved firmware validation and flashing code from the switch driver to
mlxsw_core so that it is performed before driver initialization.
Therefore, change the initialization sequence back to its original form.
In addition to being more straightforward, it will allow us to simplify
parts of the code in subsequent patches and future patchsets.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The devlink parameters were published in two steps despite being static
and known in advance.
First step was to use devlink_params_publish() which iterated over all
known up to that point parameters and sent notification messages.
In second step, the call was devlink_param_publish() that looped over
same parameters list and sent notification for new parameters.
In order to simplify the API, move devlink_params_publish() to be called
when all parameters were already added and save the need to iterate over
parameters list again.
As a side effect, this change fixes the error unwind flow in which
parameters were not marked as unpublished.
Fixes: 82e6c96f04e1 ("net/mlx5: Register to devlink ingress VLAN filter trap")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For testing visibility of mq/mqprio default children.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than releasing the tx pools on every close and reallocating
them on open, reuse the tx pools unless the pool parameters (number
of pools, size of each pool or size of each buffer in a pool) have
changed.
If the pool parameters changed, then release the old pools (if
any) and allocate new ones.
Specifically release tx pools, if:
- adapter is removed,
- pool parameters change during reset,
- we encounter an error when opening the adapter in response
to a user request (in ibmvnic_open()).
and don't release them:
- in __ibmvnic_close() or
- on errors in __ibmvnic_open()
in the hope that we can reuse them during this or next reset.
With these changes reset_tx_pools() can be dropped because its
optimization is now included in init_tx_pools() itself.
cleanup_tx_pools() releases all the skbs associated with the pool and
is called from ibmvnic_cleanup(), which is called on every reset. Since
we want to reuse skbs across resets, move cleanup_tx_pools() out of
ibmvnic_cleanup() and call it only when user closes the adapter.
Add two new adapter fields, ->prev_mtu, ->prev_tx_pool_size to track the
previous values and use them to decide whether to reuse or realloc the
pools.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than releasing the rx pools on and reallocating them on every
reset, reuse the rx pools unless the pool parameters (number of pools,
size of each pool or size of each buffer in a pool) have changed.
If the pool parameters changed, then release the old pools (if any)
and allocate new ones.
Specifically release rx pools, if:
- adapter is removed,
- pool parameters change during reset,
- we encounter an error when opening the adapter in response
to a user request (in ibmvnic_open()).
and don't release them:
- in __ibmvnic_close() or
- on errors in __ibmvnic_open()
in the hope that we can reuse them on the next reset.
With these, reset_rx_pools() can be dropped because its optimzation is
now included in init_rx_pools() itself.
cleanup_rx_pools() releases all the skbs associated with the pool and
is called from ibmvnic_cleanup(), which is called on every reset. Since
we want to reuse skbs across resets, move cleanup_rx_pools() out of
ibmvnic_cleanup() and call it only when user closes the adapter.
Add two new adapter fields, ->prev_rx_buf_sz, ->prev_rx_pool_size to
keep track of the previous values and use them to decide whether to
reuse or realloc the pools.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reuse the long term buffer during a reset as long as its size has
not changed. If the size has changed, free it and allocate a new
one of the appropriate size.
When we do this, alloc_long_term_buff() and reset_long_term_buff()
become identical. Drop reset_long_term_buff().
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a follow-on patch, we will reuse long term buffers when possible.
When doing so we have to be careful to properly assign map ids. We
can no longer assign them sequentially because a lower map id may be
available and we could wrap at 255 and collide with an in-use map id.
Instead, use a bitmap to track active map ids and to find a free map id.
Don't need to take locks here since the map_id only changes during reset
and at that time only the reset worker thread should be using the adapter.
Noticed this when analyzing an error Dany Madden ran into with the
patch set.
Reported-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In init_tx_pools() move some loop-invariant code out of the loop.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use/rename local variables in init_tx_pools() for consistency with
init_rx_pools() and for readability. Also add some comments
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code more readable, use/rename some local variables.
Basically we have a set of pools, num_pools. Each pool has a set of
buffers, pool_size and each buffer is of size buff_size.
pool_size is a bit ambiguous (whether size in bytes or buffers). Add
a comment in the header file to make it explicit.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add/update some comments/function headers and fix up some messages.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better readability, consolidate related code in replenish_rx_pool()
and add some comments.
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configure the burst length in Ethernet drivers. This improves
Ethernet performance by 58%. According to the vendor BSP,
8W burst length is supported by ar9 and newer SoCs.
The NAT benchmark results on xRX200 (Down/Up):
* 2W: 330 Mb/s
* 4W: 432 Mb/s 372 Mb/s
* 8W: 520 Mb/s 389 Mb/s
Tested on xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function is called to enable SR-IOV when available,
not enabling interfaces without VFs was a regression.
Fixes: 65161c35554f ("bnx2x: Fix missing error code in bnx2x_iov_init_one()")
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reported-by: YunQiang Su <wzssyqa@gmail.com>
Tested-by: YunQiang Su <wzssyqa@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Shai Malin <smalin@marvell.com>
Link: https://lore.kernel.org/r/20210912190523.27991-1-bunk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Linus Torvalds
Ilan Peer
Srujana Challa
Jakub Kicinski
David Thompson
Hariprasad Kelam
Paolo Abeni
Eli Cohen
Adam Borowski
Cai Huoqing
Seevalamuthu Mariappan
Karthikeyan Periyasamy
Sathishkumar Muruganandam
Christian Lamparter
Vladimir Oltean
Guenter Roeck
Ido Schimmel
Leon Romanovsky
Sukadev Bhattiprolu
Aleksander Jan Bajkowski
Randy Dunlap
Adrian Bunk