Age | Commit message (Collapse) | Author | Files | Lines |
|
Updates visual effect for advertised mode after setting desired mode.
The mode appears in advertised FEC mode correctly, when ethtool
interface command is called. Without this commit advertised FEC
is displayed regardless of the settings as "None BaseR RS".
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Found a code comment that needed TLC to correct their formatting.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
Commit d3d657a90850 ("i40e: update VFs of link state after
GET_VF_RESOURCES") modified the PF driver to notify a VF of
its link status immediately after it requests resources.
This was intended to fix reporting on VF drivers, so that they would
properly report link status.
However, some older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.
More recent versions of the old i40evf and all versions of iavf are
resilient to these early link status messages. However, if a VM happens
to run an older version of the VF driver, this can be problematic.
Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add logging for disable-fw-lldp flag by ethtool. Added check
for I40E_FLAG_DISABLE_FW_LLDP and logging state in dmesg.
Without this commit there was no clear statement in dmesg
about FW LLDP state in dmesg.
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes missing call of i40e_update_veb_stats() in function
i40e_get_ethtool_stats() to update stats data of VEB and VEB TC
counters before they are written into ethtool buffer.
Before the patch ethtool counters may fell behind interface counters.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is a spelling mistake in an error messgae. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add use case section to fcnal-test.
Initial test is VRF based with a bridge and vlans. The commands
stem from bug reports fixed by:
a173f066c7cf ("netfilter: bridge: Don't sabotage nf_hook calls from an l3mdev")
cd6428988bf4 ("netfilter: bridge: Don't sabotage nf_hook calls for an l3mdev slave")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 netfilter tests to send tcp reset or icmp unreachable for a
port. Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netfilter tests to send tcp reset or icmp unreachable for a port.
Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 runtime tests where passive (no traffic flowing) and active
(with traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add runtime tests where passive (no traffic flowing) and active (with
traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv6 ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.
Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.
Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initial commit for functional test suite for fib and socket lookups.
This commit contains the namespace setup, networking config, test options
and other basic infrastructure.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add nettest - a simple program with an implementation for various networking
APIs. nettest is used for tcp, udp and raw functional tests for both IPv4
and IPv6.
Point of this command versus existing utilities:
- controlled implementation of the APIs and the order in which they
are called,
- ability to verify ingress device, local and remote addresses,
- timeout for controlled test length,
- ability to discriminate a timeout from a system call failure, and
- simplicity with test scripts.
The command returns:
0 on success,
1 for any system call failure, and
2 on timeout.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LS1028a has one Ethernet management interface. On the QDS board, the
MDIO signals are multiplexed to either on-board AR8035 PHY device or
to 4 PCIe slots allowing for SGMII cards.
To enable the Ethernet ENETC Port 1, which can only be connected to a
RGMII PHY, the multiplexer needs to be configured to route the MDIO to
the AR8035 PHY. The MDIO/MDC routing is controlled by bits 7:4 of FPGA
board config register 0x54, and value 0 selects the on-board RGMII PHY.
The FPGA board config registers are accessible on the i2c bus, at address
0x66.
The PF3 MDIO PCIe integrated endpoint device allows for centralized access
to the MDIO bus. Add the corresponding devicetree node and set it to be
the MDIO bus parent.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The on-chip PCIe root complex that integrates the ENETC ethernet
controllers also integrates a PCIe endpoint for the MDIO controller
providing for centralized control of the ENETC mdio bus.
Add bindings for this "central" MDIO Integrated PCIe Endpoint.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENETC ports can manage the MDIO bus via local register
interface. However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).
Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers. For instance, on the LS1028A QDS board
where MDIO muxing is required. Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.
The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access. It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules. This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.
Fixes following sparse warning:
warning: incorrect type in assignment (different address spaces)
expected void *priv
got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs
Fixes: ebfcb23d62ab ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it is done for all the other structs within this driver.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.
If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6220 is part of the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensures we can talk to a PHY via MDIO on the AST2600, as the MDIO
controller is now separate from the MAC.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy-handle is necessary for the AST2600 which separates the MDIO
controllers from the MAC.
I've tried to minimise the intrusion of supporting the AST2600 to the
FTGMAC100 by leaving in place the existing MDIO support for the embedded
MDIO interface. The AST2400 and AST2500 continue to be supported this
way, as it avoids breaking/reworking existing devicetrees.
The AST2600 support by contrast requires the presence of the phy-handle
property in the MAC devicetree node to specify the appropriate PHY to
associate with the MAC. In the event that someone wants to specify the
MDIO bus topology under the MAC node on an AST2400 or AST2500, the
current auto-probe approach is done conditional on the absence of an
"mdio" child node of the MAC.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|