| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull opertaing performance points (OPP) framework fixes for 5.10-rc1
from Viresh Kumar:
"- Return -EPROBE_DEFER properly from dev_pm_opp_get_opp_table()
(Stephan Gerhold).
- Minor cleanups around required-opps (Stephan Gerhold).
- Extends opp-supported-hw property to contain multiple versions
(Viresh Kumar).
- Multiple cleanups around dev_pm_opp_attach_genpd() (Viresh Kumar).
- Multiple fixes, cleanups in the OPP core for overall better design
(Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Allow opp-level to be set to 0
opp: Prevent memory leak in dev_pm_opp_attach_genpd()
ARM: tegra: Pass multiple versions in opp-supported-hw property
opp: Allow opp-supported-hw to contain multiple versions
dt-bindings: opp: Allow opp-supported-hw to contain multiple versions
opp: Set required OPPs in reverse order when scaling down
opp: Reduce code duplication in _set_required_opps()
opp: Drop unnecessary check from dev_pm_opp_attach_genpd()
opp: Handle multiple calls for same OPP table in _of_add_opp_table_v1()
opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER
opp: Remove _dev_pm_opp_find_and_remove_table() wrapper
opp: Split out _opp_set_rate_zero()
opp: Reuse the enabled flag in !target_freq path
opp: Rename regulator_enabled and use it as status of all resources
|
|
The DT bindings don't put such a constraint, nor should the kernel. It
is perfectly fine for opp-level to be set to 0, if we need to put the
performance state votes for a domain for a particular OPP.
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
If dev_pm_opp_attach_genpd() is called multiple times (once for each CPU
sharing the table), then it would result in unwanted behavior like
memory leak, attaching the domain multiple times, etc.
Handle that by checking and returning earlier if the domains are already
attached. Now that dev_pm_opp_detach_genpd() can get called multiple
times as well, we need to protect that too.
Note that the virtual device pointers aren't returned in this case, as
they may become unavailable to some callers during the middle of the
operation.
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The bindings allow multiple versions to be passed to "opp-supported-hw"
property, either of which can result in enabling of the OPP.
Update code to allow that.
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP core already has well-defined semantics to ensure required
OPPs/regulators are set before/after the frequency change, depending
on if we scale up or down.
Similar requirements might exist for the order of required OPPs
when multiple power domains need to be scaled for a frequency change.
For example, on Qualcomm platforms using CPR (Core Power Reduction),
we need to scale the VDDMX and CPR power domain. When scaling up,
MX should be scaled up before CPR. When scaling down, CPR should be
scaled down before MX.
In general, if there are multiple "required-opps" in the device tree
I would expect that the order is either irrelevant, or there is some
dependency between the power domains. In that case, the power domains
should be scaled down in reverse order.
This commit updates _set_required_opps() to set required OPPs in
reverse order when scaling down.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[ Viresh: Fix rebase conflict and minor rearrangement of the code ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Move call to dev_pm_genpd_set_performance_state() to a separate
function so we can avoid duplicating the code for the single and
multiple genpd case.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[ Viresh: Validate virtual device before use ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Since commit c0ab9e0812da ("opp: Allocate genpd_virt_devs from
dev_pm_opp_attach_genpd()"), the allocation of the virtual devices is
moved to dev_pm_opp_attach_genpd() and this check isn't required anymore
as it will always fail. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
|
|
Until now for V1 OPP bindings we used to call
dev_pm_opp_of_cpumask_add_table() first and then
dev_pm_opp_set_sharing_cpus() in the cpufreq-dt driver.
A later patch will though update the cpufreq-dt driver to optimize the
code a bit and we will call dev_pm_opp_set_sharing_cpus() first followed
by dev_pm_opp_of_cpumask_add_table(), which doesn't work well today as
it tries to re parse the OPP entries. This should work nevertheless for
V1 bindings as the same works for V2 bindings.
Adapt the same approach from V2 bindings and fix this.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Pull operating performance points (OPP) framework fixes for 5.9-rc4 from
Viresh Kumar:
"This fixes reference counting for OPP tables. Few patches are getting
queued (for various subsystems) for 5.10 which depend on this to be
fixed first."
* 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Don't drop reference for an OPP table that was never parsed
|
|
dev_pm_opp_remove_table() should drop a reference to the OPP table only
if the DT OPP table was parsed earlier with a call to
dev_pm_opp_of_add_table() earlier. Else it may end up dropping the
reference to the OPP table, which was added as a result of other calls
like dev_pm_opp_set_clkname(). And would hence result in undesirable
behavior later on when caller would try to free the resource again.
Fixes: 03758d60265c ("opp: Replace list_kref with a local counter")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP core manages various resources, e.g. clocks or interconnect paths.
These resources are looked up when the OPP table is allocated once
dev_pm_opp_get_opp_table() is called the first time (either directly
or indirectly through one of the many helper functions).
At this point, the resources may not be available yet, i.e. looking them
up will result in -EPROBE_DEFER. Unfortunately, dev_pm_opp_get_opp_table()
is currently unable to propagate this error code since it only returns
the allocated OPP table or NULL.
This means that all consumers of the OPP core are required to make sure
that all necessary resources are available. Usually this happens by
requesting them, checking the result and releasing them immediately after.
For example, we have added "dev_pm_opp_of_find_icc_paths(dev, NULL)" to
several drivers now just to make sure the interconnect providers are
ready before the OPP table is allocated. If this call is missing,
the OPP core will only warn about this and then attempt to continue
without interconnect. This will eventually fail horribly, e.g.:
cpu cpu0: _allocate_opp_table: Error finding interconnect paths: -517
... later ...
of: _read_bw: Mismatch between opp-peak-kBps and paths (1 0)
cpu cpu0: _opp_add_static_v2: opp key field not found
cpu cpu0: _of_add_opp_table_v2: Failed to add OPP, -22
This example happens when trying to use interconnects for a CPU OPP
table together with qcom-cpufreq-nvmem.c. qcom-cpufreq-nvmem calls
dev_pm_opp_set_supported_hw(), which ends up allocating the OPP table
early. To fix the problem with the current approach we would need to add
yet another call to dev_pm_opp_of_find_icc_paths(dev, NULL).
But actually qcom-cpufreq-nvmem.c has nothing to do with interconnects...
This commit attempts to make this more robust by allowing
dev_pm_opp_get_opp_table() to return an error pointer. Fixing all
the usages is trivial because the function is usually used indirectly
through another helper (e.g. dev_pm_opp_set_supported_hw() above).
These other helpers already return an error pointer.
The example above then works correctly because set_supported_hw() will
return -EPROBE_DEFER, and qcom-cpufreq-nvmem.c already propagates that
error. It should also be possible to remove the remaining usages of
"dev_pm_opp_of_find_icc_paths(dev, NULL)" from other drivers as well.
Note that this commit currently only handles -EPROBE_DEFER for the
clock/interconnects within _allocate_opp_table(). Other errors are just
ignored as before. Eventually those should be propagated as well.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: skip checking return value of dev_pm_opp_get_opp_table() for
EPROBE_DEFER in domain.c, fix NULL return value and reorder
code a bit in core.c, and update exynos-asv.c ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Remove the unnecessary wrapper and merge
_dev_pm_opp_find_and_remove_table() with dev_pm_opp_remove_table().
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Create separate routine _opp_set_rate_zero() to handle !target_freq
case.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP core needs to track if the resources of devices are
enabled/configured or not, as it disables the resources when target_freq
is set to 0.
Handle that with the new enabled flag and remove otherwise complex
conditional statements.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Expand the scope of the regulator_enabled flag and use it to track
status of all the resources. This will be used for other stuff in the
next patch.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
dev_pm_opp_set_rate() can now be called with freq = 0 in order
to either drop performance or bandwidth votes or to disable
regulators on platforms which support them.
In such cases, a subsequent call to dev_pm_opp_set_rate() with
the same frequency ends up returning early because 'old_freq == freq'
Instead make it fall through and put back the dropped performance
and bandwidth votes and/or enable back the regulators.
Cc: v5.3+ <stable@vger.kernel.org> # v5.3+
Fixes: cd7ea582866f ("opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes")
Reported-by: Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[ Viresh: Don't skip clk_set_rate() and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.8+ <stable@vger.kernel.org> # v5.8+
Fixes: b00e667a6d8b ("opp: Remove bandwidth votes when target_freq is zero")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Fixes: aca48b61f963 ("opp: Manage empty OPP tables with clk handle")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Pull ARM cpufreq driver changes for v5.9-rc1 from Viresh Kumar:
"Here are the details:
- Adaptive voltage scaling (AVS) support and minor cleanups for
brcmstb driver (Florian Fainelli and Markus Mayer).
- A new tegra driver and cleanup for the existing one (Sumit Gupta and
Jon Hunter).
- Bandwidth level support for Qcom driver along with OPP changes (Sibi
Sankar).
- Cleanups to sti, cpufreq-dt, ap806, CPPC drivers (Viresh Kumar, Lee
Jones, Ivan Kokshaysky, Sven Auhagen, and Xin Hao).
- Make schedutil default governor for ARM (Valentin Schneider).
- Fix dependency issues for imx (Walter Lozano).
- Cleanup around cached_resolved_idx in cpufreq core (Viresh Kumar)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: make schedutil the default for arm and arm64
cpufreq: cached_resolved_idx can not be negative
cpufreq: Add Tegra194 cpufreq driver
dt-bindings: arm: Add NVIDIA Tegra194 CPU Complex binding
cpufreq: imx: Select NVMEM_IMX_OCOTP
cpufreq: sti-cpufreq: Fix some formatting and misspelling issues
cpufreq: tegra186: Simplify probe return path
cpufreq: CPPC: Reuse caps variable in few routines
cpufreq: ap806: fix cpufreq driver needs ap cpu clk
cpufreq: cppc: Reorder code and remove apply_hisi_workaround variable
cpufreq: dt: fix oops on armada37xx
cpufreq: brcmstb-avs-cpufreq: send S2_ENTER / S2_EXIT commands to AVS
cpufreq: brcmstb-avs-cpufreq: Support polling AVS firmware
cpufreq: brcmstb-avs-cpufreq: more flexible interface for __issue_avs_command()
cpufreq: qcom: Disable fast switch when scaling DDR/L3
cpufreq: qcom: Update the bandwidth levels on frequency change
OPP: Add and export helper to set bandwidth
cpufreq: blacklist SC7180 in cpufreq-dt-platdev
cpufreq: blacklist SDM845 in cpufreq-dt-platdev
|
|
* pm-em:
OPP: refactor dev_pm_opp_of_register_em() and update related drivers
Documentation: power: update Energy Model description
PM / EM: change name of em_pd_energy to em_cpu_energy
PM / EM: remove em_register_perf_domain
PM / EM: add support for other devices than CPUs in Energy Model
PM / EM: update callback structure and add device pointer
PM / EM: introduce em_dev_register_perf_domain function
PM / EM: change naming convention from 'capacity' to 'performance'
* pm-core:
mmc: jz4740: Use pm_ptr() macro
PM: Make *_DEV_PM_OPS macros use __maybe_unused
PM: core: introduce pm_ptr() macro
|
|
Add and export 'dev_pm_opp_set_bw' to set the bandwidth
levels associated with an OPP.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Allow dev_pm_opp_get_freq() to work for disabled OPPs.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
[ Viresh: Massaged commit log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Export dev_pm_opp_adjust_voltage() as it may be used by modules later
on.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
[ Viresh: Rewrote commit log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Currently, when using _of_add_opp_table_v2 parsed_static_opps is
increased and this value is used in _opp_remove_all_static() to
check if there are static opp entries that need to be freed.
Unfortunately this does not happen when using _of_add_opp_table_v1(),
which leads to warnings.
This patch increases parsed_static_opps in _of_add_opp_table_v1() in a
similar way as in _of_add_opp_table_v2().
Fixes: 03758d60265c ("opp: Replace list_kref with a local counter")
Cc: v5.6+ <stable@vger.kernel.org> # v5.6+
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
[ Viresh: Do the operation with lock held and set the value to 1 instead
of incrementing it ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The Energy Model framework supports not only CPU devices. Drop the CPU
specific interface with cpumask and add struct device. Add also a return
value, user might use it. This new interface provides easy way to create
a simple Energy Model, which then might be used by e.g. thermal subsystem.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Energy Model framework is going to support devices other that CPUs. In
order to make this happen change the callback function and add pointer to
a device as an argument.
Update the related users to use new function and new callback from the
Energy Model.
Acked-by: Quentin Perret <qperret@google.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
The DT node of the device may contain interconnect paths while the OPP
table doesn't have the bandwidth values. There is no need to parse the
paths in such cases.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
[ Viresh: Support the case of !opp_table and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We already drop several votes when target_freq is set to zero, drop
bandwidth votes as well.
Reported-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add enable regulators to dev_pm_opp_set_regulators() and disable
regulators to dev_pm_opp_put_regulators(). Even if bootloader
leaves regulators enabled, they should be enabled in kernel in
order to increase the reference count.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Clément Péron <peron.clem@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
[ Viresh: Enable the regulator only after it is programmed and add a
flag to track its status. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Reorder the code a bit to make it more readable. Add additional comment
as well.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Clément Péron <peron.clem@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Expose the bandwidth information as well via debugfs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
If the OPP bandwidth values are populated, we want to switch also the
interconnect bandwidth in addition to frequency and voltage.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
When we read the OPP keys, it would be nice to do some sanity checks
of the values we get from DT and see if they match with the information
that is populated in the OPP table. Let's pass a pointer of the table,
so that we can do some validation.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
[ Viresh: Fix rebase conflicts ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The OPP bindings now support bandwidth values, so add support to parse it
from device tree and store it into the new dev_pm_opp_icc_bw struct, which
is part of the dev_pm_opp.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
[ Viresh: Create _read_bw() and use it, renamed _of_find_icc_paths() to
dev_pm_opp_of_find_icc_paths(), exported it and made opp_table
argument optional. Also drop the depends on from Kconfig. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The opp-hz DT property is not mandatory and we may use another property
as a key in the OPP table. Add helper functions to simplify the reading
and comparing the keys.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
[ Viresh: Removed an unnecessary comment ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
With OPP core now supporting DVFS for IO devices, we have instances of
IO devices (same IP block) which require an OPP on some platforms/SoCs
while just needing to scale the clock on some others.
In order to avoid conditional code in every driver which supports such
devices (to check for availability of OPPs and then deciding to do
either dev_pm_opp_set_rate() or clk_set_rate()) add support to manage
empty OPP tables with a clk handle.
This makes dev_pm_opp_set_rate() equivalent of a clk_set_rate() for
devices with just a clk and no OPPs specified, and makes
dev_pm_opp_set_rate(0) bail out without throwing an error.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
A kref or refcount isn't the right tool to be used here for counting
number of devices that are sharing the static OPPs created for the OPP
table. For example, we are reinitializing the kref again, after it
reaches a value of 0 and frees the resources, if the static OPPs get
added for the same OPP table structure (as the OPP table structure was
never freed). That is messy and very unclear.
This patch makes parsed_static_opps an unsigned integer and uses it to
count the number of users of the static OPPs. The increment and
decrement to parsed_static_opps is done under opp_table->lock now to
make sure no races are possible if the OPP table is getting added and
removed in parallel (which doesn't happen in practice, but can in
theory).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The static OPPs aren't getting freed properly, if errors occur while
adding them. Fix that by calling _put_opp_list_kref() and putting their
reference on failures.
Fixes: 11e1a1648298 ("opp: Don't decrement uninitialized list_kref")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
On some SoCs the Adaptive Voltage Scaling (AVS) technique is
employed to optimize the operating voltage of a device. At a
given frequency, the hardware monitors dynamic factors and either
makes a suggestion for how much to adjust a voltage for the
current frequency, or it automatically adjusts the voltage
without software intervention. Add an API to the OPP library for
the former case, so that AVS type devices can update the voltages
for an OPP when the hardware determines the voltage should
change. The assumption is that drivers like CPUfreq or devfreq
will register for the OPP notifiers and adjust the voltage
according to suggestions that AVS makes.
This patch is derived from [1] submitted by Stephen.
[1] https://lore.kernel.org/patchwork/patch/599279/
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[Roger Lu: Changed to rcu less implementation]
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
[s.nawrocki@samsung.com: added handling of OPP min/max voltage]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The list_kref reaches a count of 0 when all the static OPPs are removed,
for example when dev_pm_opp_of_cpumask_remove_table() is called, though
the actual OPP table may not get freed as it may still be referenced by
other parts of the kernel, like from a call to
dev_pm_opp_set_supported_hw(). And if we call
dev_pm_opp_of_cpumask_add_table() again at this point, we must
reinitialize the list_kref otherwise the kernel will hit a WARN() in
kref infrastructure for incrementing a kref with value 0.
Fixes: 11e1a1648298 ("opp: Don't decrement uninitialized list_kref")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
All the drivers, which use the OPP framework control regulators, which
are already enabled. Typically those regulators are also system critical,
due to providing power to CPU core or system buses. It turned out that
there are cases, where calling regulator_enable() on such boot-enabled
regulator has side-effects and might change its initial voltage due to
performing initial voltage balancing without all restrictions from the
consumers. Until this issue becomes finally solved in regulator core,
avoid calling regulator_enable()/disable() from the OPP framework.
This reverts commit 7f93ff73f7c8c8bfa6be33bcc16470b0b44682aa.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
_find_opp_of_np() doesn't traverse the list of OPP tables but instead
just the entries within an OPP table and so only requires to lock the
OPP table itself.
The lockdep_assert_held() was added there by mistake and isn't really
required.
Fixes: 5d6d106fa455 ("OPP: Populate required opp tables from "required-opps" property")
Cc: v5.0+ <stable@vger.kernel.org> # v5.0+
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
With property "opp-supported-hw" introduced, the OPP table
in DT could be a large OPP table and ONLY a subset of OPPs
are available, based on the version of the hardware running
on. That introduces restriction of using "opp-suspend"
property to define the suspend OPP, as we are NOT sure if the
OPP containing "opp-suspend" property is available for the
hardware running on, and the of opp core does NOT allow multiple
suspend OPPs defined in DT OPP table.
To eliminate this restrition, make of opp core allow multiple
suspend OPPs defined in DT, and pick the OPP with highest rate
and with "opp-suspend" property present to be suspend OPP, it
can speed up the suspend/resume process.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Add enable regulators to dev_pm_opp_set_regulators() and disable
regulators to dev_pm_opp_put_regulators(). Even if bootloader
leaves regulators enabled, they should be enabled in kernel in
order to increase the reference count.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The list_kref was added for static OPPs and to track their users. The
kref is initialized while the static OPPs are added, but removed
unconditionally even if the static OPPs were never added. This causes
refcount mismatch warnings currently.
Fix that by always initializing the kref when the OPP table is first
initialized. The refcount is later incremented only for the second user
onwards.
Fixes: d0e8ae6c26da ("OPP: Create separate kref for static OPPs list")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
Rafael J. Wysocki
Viresh Kumar
Stephan Gerhold
Rajendra Nayak
Stephen Boyd
Sibi Sankar
Andrew-sh.Cheng
Alexander A. Klimov
Valdis Klētnieks
Walter Lozano
Lukasz Luba
Masahiro Yamada
Kamil Konieczny
Georgi Djakov
Saravana Kannan
Linus Torvalds
Christoph Hellwig
Stephen Boyd
Marek Szyprowski
Anson Huang
k.konieczny@partner.samsung.com