| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
They were implicitly getting it from device.h --> module.h but
we want to clean that up. So add the minimal header for these
macros.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
|
|
Intel 5000 and 5100 series memory controllers have a known issue if read
completion coalescing is enabled and the PCI-E Maximum Payload Size is
set to 256B. To work around this issue, disable read completion
coalescing in the memory controller and root complexes. Unfortunately,
it must always be disabled, even if no 256B MPS devices are present, due
to the possibility of one being hotplugged.
Links to erratas:
http://www.intel.com/content/dam/doc/specification-update/5000-chipset-memory-controller-hub-specification-update.pdf
http://www.intel.com/content/dam/doc/specification-update/5100-memory-controller-hub-chipset-specification-update.pdf
Thanks to Jesse Brandeburg and Ben Hutchings for providing insight into
the problem.
Tested-and-Reported-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Commit 15bed0f2f added a quirk for the e823 Ricoh card reader to lower the
base frequency. However, the quirk first checks to see if the proprietary
MMC controller is disabled, and returns if so. On some devices, such as the
Lenovo X220, the MMC controller is already disabled by firmware it seems,
but the frequency change is still needed so sdhci-pci can talk to the cards.
Since the MMC controller is disabled, the frequency fixup was never being run
on these machines.
This moves the e823 check above the MMC controller check so that it always
gets run.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=722509
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Using legacy interrupts and TLPs > 256 bytes on the SFC4000 (all
revisions) may cause interrupt messages to be replayed. In some
systems this results in a non-recoverable MCE. Early boards using the
SFC4000 set the maximum payload size supported (MPSS) to 1024 bytes
and we should override that.
There are probably other devices with similar issues, so give this
quirk a generic name.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change the CONFIG_DMAR to CONFIG_INTEL_IOMMU to be consistent
with the other IOMMU options.
Rename the CONFIG_INTR_REMAP to CONFIG_IRQ_REMAP to match the
irq subsystem name.
And define the CONFIG_DMAR_TABLE for the common ACPI DMAR
routines shared by both CONFIG_INTEL_IOMMU and CONFIG_IRQ_REMAP.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: youquan.song@intel.com
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.558630224@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Ricoh 1180:e823 does not recognize certain types of SD/MMC cards,
as reported at http://launchpad.net/bugs/773524. Lowering the SD
base clock frequency from 200Mhz to 50Mhz fixes this issue. This
solution was suggest by Koji Matsumuro, Ricoh Company, Ltd.
This change has no negative performance effect on standard SD
cards, though it's quite possible that there will be one on
UHS-1 cards.
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: Koji Matsumuro <matsumur@nts.ricoh.co.jp>
Cc: <stable@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Don't use the costly dmi_name_in_vendors() when we know the string we
are looking for can only be in the DMI board name field. This is more
robust and, more importantly, much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We were just lucky that ICH4_GPIO_EN and ICH6_GPIO_EN happen to have
the same value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Some broken BIOSes on ICH4 chipset report an ACPI region which is in
conflict with legacy IDE ports when ACPI is disabled. Even though the
regions overlap, IDE ports are working correctly (we cannot find out
the decoding rules on chipsets).
So the only problem is the reported region itself, if we don't reserve
the region in the quirk everything works as expected.
This patch avoids reserving any quirk regions below PCIBIOS_MIN_IO
which is 0x1000. Some regions might be (and are by a fast google
query) below this border, but the only difference is that they won't
be reserved anymore. They should still work though the same as before.
The conflicts look like (1f.0 is bridge, 1f.1 is IDE ctrl):
pci 0000:00:1f.1: address space collision: [io 0x0170-0x0177] conflicts with 0000:00:1f.0 [io 0x0100-0x017f]
At 0x0100 a 128 bytes long ACPI region is reported in the quirk for
ICH4. ata_piix then fails to find disks because the IDE legacy ports
are zeroed:
ata_piix 0000:00:1f.1: device not available (can't reserve [io 0x0000-0x0007])
References: https://bugzilla.novell.com/show_bug.cgi?id=558740
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Per ICH4 and ICH6 specs, ACPI and GPIO regions are valid iff ACPI_EN
and GPIO_EN bits are set to 1. Add checks for these bits into the
quirks prior to the region creation.
While at it, name the constants by macros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Revert commit 7eb93b175d4de9438a4b0af3a94a112cb5266944
Author: Yu Zhao <yu.zhao@intel.com>
Date: Fri Apr 3 15:18:11 2009 +0800
PCI: SR-IOV quirk for Intel 82576 NIC
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk was added before SR-IOV was in production and now all machines that
originally had this issue alreayd have bios updates to correct the issue. The
quirk itself is no longer needed and in fact causes bugs if run. Remove it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
|
|
I wrote this quirk awhile ago to properly setup MCP55 chips on hypertransport
busses so that interrupts reached whatever cpu happend to boot the kdump kernel.
while that works well, it was recently shown to me that a a non-hypertransport
variant of the MCP55 exists, and on those system the register that this quirk
manipulates causes hangs if you write to it. Since the quirk was only meant to
handle errors found on MCP55 chips that have a HT interface, this patch adds a
filter to make sure the chip is an HT capable before making the needed register
adjustment. This lets the broken MCP55s work with kdump while not breaking the
non-HT variants.
Resolves https://bugzilla.kernel.org/show_bug.cgi?id=23952
Tested successfully by the reporter and myself.
Cc: stable@kernel.org
Reported-by: Mathieu Bérard <mathieu@mberard.eu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com>
Cc: stable@kernel.org [v2.6.32+]
Reported-by: Max Asbock <masbock@linux.vnet.ibm.com>
Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This change enables PCI root complex support for TILEPro. Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc. However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).
The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space. The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified. Both of the latter two headers were
preliminary versions not meant for release before now - oh well.
There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
|
|
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Update broken web addresses in arch directory.
Update broken web addresses in the kernel.
Revert "drivers/usb: Remove unnecessary return's from void functions" for musb gadget
Revert "Fix typo: configuation => configuration" partially
ida: document IDA_BITMAP_LONGS calculation
ext2: fix a typo on comment in ext2/inode.c
drivers/scsi: Remove unnecessary casts of private_data
drivers/s390: Remove unnecessary casts of private_data
net/sunrpc/rpc_pipe.c: Remove unnecessary casts of private_data
drivers/infiniband: Remove unnecessary casts of private_data
drivers/gpu/drm: Remove unnecessary casts of private_data
kernel/pm_qos_params.c: Remove unnecessary casts of private_data
fs/ecryptfs: Remove unnecessary casts of private_data
fs/seq_file.c: Remove unnecessary casts of private_data
arm: uengine.c: remove C99 comments
arm: scoop.c: remove C99 comments
Fix typo configue => configure in comments
Fix typo: configuation => configuration
Fix typo interrest[ing|ed] => interest[ing|ed]
Fix various typos of valid in comments
...
Fix up trivial conflicts in:
drivers/char/ipmi/ipmi_si_intf.c
drivers/usb/gadget/rndis.c
net/irda/irnet/irnet_ppp.c
|
|
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
A long time ago I worked on a RHEL5 bug in which kdump hung during boot
on a set of systems. The systems hung because they never received timer
interrupts during calibrate_delay. These systems also all had Opteron
processors on a hypertransport bus, bridged to a pci bus via an Nvidia
MCP55 northbridge chip. After much wrangling I managed to learn from
Nvidia that they have an undocumented register in some versions of that
chip which control how legacy interrupts are send to the cpu complex
when the ioapic isn't active. Nvidia defaults this register to only
send legacy interrupts to the BSP, so if kdump happens to boot on an AP,
we never get timer interrupts and boom. I had initially used this quirk
as a workaround, with my intent being to move apic initalization to an
earlier point in the boot process, so the setting of the register would
be irrelevant. Given the work involved in doing that however, the
fragile nature of the apic initalization code, and the fact that, over
the 2 years since we found this bug, the MCP55 is the only chip which
seems to have this issue, I've figure at this point its likely safer to
just carry the quirk around. By setting the referenced bits in this
hidden register, interrupts will be broadcast to all cpus when the
ioapic isn't active on the above described systems.
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
When the Lenovo Ideapad S10-3 is booted with HT enabled,
it hits a boot hang in the intel_idle driver.
This occurs when entering ATM-C4 for the first time,
unless BM_STS is first cleared.
acpi_idle doesn't see this because it first checks
and clears BM_STS, but it would hit the same hang
if that check were disabled.
http://bugs.meego.com/show_bug.cgi?id=7093
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/634702
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
|
|
Add support for JMB364 and 369.
Patch-originally-from: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
There is no reason to run NVidia-specific quirks related to HT MSI
mappings with MSI disabled via pci=nomsi, so make
__nv_msi_ht_cap_quirk() return immediately in that case.
This allows at least one machine to boot 100% of the time with
pci=nomsi (it still doesn't boot reliably without that).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16443 .
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Use for_each_pci_dev() to simplify the code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.
A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.
Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
MSI delivery from on-board ahci controller doesn't work on K8M800. At
this point, it's unclear whether the culprit is with the ahci
controller or the host bridge. Given the track record and considering
the rather minimal impact of MSI, disabling it seems reasonable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rainer Hurtado Navarro <publio.escipion.el.africano@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In all AMD 780 family northbridges, the vendor ID of the internal
graphics PCI/PCI bridge reads not as AMD but as that of the mainboard
vendor, because the hardware actually returns the value of the subsystem
vendor ID (erratum 18).
We currently have additional quirk entries for Asus and Acer, but it is
likely that we will encounter more systems with other vendor IDs.
Since we do not know in advance all possible vendor IDs, a better way to
find the device is to declare the quirk on the host bridge, whose ID is
always correct, and use that device as a stepping stone to find the PCI/
PCI bridge, if present.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Aries Lee <arieslee@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
At the moment only PCI-E briges can be flagged as hotplug, thus
allowing manual resource preallocation via pci=hpmemsize=nnM and
pci=hpiosize=nnM kernel parameters. Some PCI hotplug bridges, e.g.
PLX 6254 can also benefit from this functionalily, as kernel fails
to properly allocate their resources when hotplug device is added
and PCI bus is rescanned.
This patch adds header quirk for PLX 6254 that marks this bridge
as hotplug. Other PCI bridges with similar problems can use it
as well.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Doesn't work reliably for internal gfx. Fixes kernel bug
https://bugzilla.kernel.org/show_bug.cgi?id=15626.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
As reported in <http://bugs.debian.org/552299>, MSI appears to be
broken for this on-board device. We already have a quirk for the
P5N32-SLI Premium; extend it to cover both variants of the board.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines. To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.
[rjw: Added the PCI_VENDOR_ID_AI quirk.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
pci_claim_resource() can fail, so pay attention and only claim success
when it actually succeeded. If pci_claim_resource() fails, it prints a
useful diagnostic.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Bugzilla 15287 indicates that there's a problem with Message Signalled
Interrupts on VIA K8T890 systems. Add a quirk to disable MSI on these
systems.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Tested-by: lh <jarryson@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):
The SBIOS must enable internal graphics MSI capability in GCCFG by
setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'
Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature. However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.
Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.
This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Apply the CX700 quirk only when an external VT6212L is present (which
is the case for the errant hardware the quirk was written for), don't
touch the settings otherwise -- Hauppage PVR-500 tuners need PCI Bus
Parking in order to work and when that's turned on everything seems
to behave fine.
I guess the underlying problem is a combination of an external VT6212L
and the CX700 rather than the CX700's PCI being broken completely for
all cases...
Reported-by: Jeroen Roos <jeroen@roosnl.com>
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch solves nasty problem original driver has.
Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.
However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.
To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.
Also regardless of the above, this way is cleaner. You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
drivers/firmware/iscsi_ibft.c
|
|
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file). This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.
To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After commit b9c3b266411d27f1a6466c19d146d08db576bfea ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.
Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Handle device specific timeout and use FLR.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Handle device specific reset requirements (i.e. vendor reg for reset
along with appropriate timeout).
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
Paul Gortmaker
Linus Torvalds
Jon Mason
Josh Boyer
Ben Hutchings
Suresh Siddha
Manoj Iyer
Jean Delvare
Hemant Pedanekar
Lucas De Marchi
Jiri Slaby
Brandeburg, Jesse
Neil Horman
Chris Metcalf
Justin P. Mattock
Len Brown
Tejun Heo
Rafael J. Wysocki
Kulikov Vasiliy
Jacob Pan
Clemens Ladisch
Felix Radensky
Alex Deucher
Ben Hutchings
Bjorn Helgaas
Matthew Wilcox
Tim Yamin
Maxim Levitsky
David S. Miller
Alexander Duyck
Andres Salomon
Dexuan Cui