| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Meelis and Helge reported that 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.
PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4fdcd, we always used 32-bit PCI addresses. After
3a9ad0b4fdcd, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.
Fixes: 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
Link: http://lkml.kernel.org/r/alpine.LRH.2.11.1507260929000.30065@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Based-on-idea-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v3.19+
|
|
We should not assume any particular hardware topology. Commit d0751b98dfa3
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
|
|
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
|
|
Mohit's email-id doesn't exist anymore as he has left the company.
Replace ST's id with mohit.kumar.dhaka@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Mohit Kumar <mohit.kumar.dhaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with pratyush.anand@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
|
|
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
|
|
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.2 merge window:
Enumeration
- Move pci_ari_enabled() to global header (Alex Williamson)
- Account for ARI in _PRT lookups (Alex Williamson)
- Remove unused pci_scan_bus_parented() (Yijing Wang)
Resource management
- Use host bridge _CRS info on systems with >32 bit addressing (Bjorn Helgaas)
- Use host bridge _CRS info on Foxconn K8M890-8237A (Bjorn Helgaas)
- Fix pci_address_to_pio() conversion of CPU address to I/O port (Zhichang Yuan)
- Add pci_bus_addr_t (Yinghai Lu)
PCI device hotplug
- Wait for pciehp command completion where necessary (Alex Williamson)
- Drop pointless ACPI-based "slot detection" check (Rafael J. Wysocki)
- Check ignore_hotplug for all downstream devices (Rafael J. Wysocki)
- Propagate the "ignore hotplug" setting to parent (Rafael J. Wysocki)
- Inline pciehp "handle event" functions into the ISR (Bjorn Helgaas)
- Clean up pciehp debug logging (Bjorn Helgaas)
Power management
- Remove redundant PCIe port type checking (Yijing Wang)
- Add dev->has_secondary_link to track downstream PCIe links (Yijing Wang)
- Use dev->has_secondary_link to find downstream links for ASPM (Yijing Wang)
- Drop __pci_disable_link_state() useless "force" parameter (Bjorn Helgaas)
- Simplify Clock Power Management setting (Bjorn Helgaas)
Virtualization
- Add ACS quirks for Intel 9-series PCH root ports (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 9120 (Sakari Ailus)
MSI
- Disable MSI at enumeration even if kernel doesn't support MSI (Michael S. Tsirkin)
- Remove unused pci_msi_off() (Bjorn Helgaas)
- Rename msi_set_enable(), msix_clear_and_set_ctrl() (Michael S. Tsirkin)
- Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl() (Michael S. Tsirkin)
- Drop pci_msi_off() calls during probe (Michael S. Tsirkin)
APM X-Gene host bridge driver
- Add APM X-Gene v1 PCIe MSI/MSIX termination driver (Duc Dang)
- Add APM X-Gene PCIe MSI DTS nodes (Duc Dang)
- Disable Configuration Request Retry Status for v1 silicon (Duc Dang)
- Allow config access to Root Port even when link is down (Duc Dang)
Broadcom iProc host bridge driver
- Allow override of device tree IRQ mapping function (Hauke Mehrtens)
- Add BCMA PCIe driver (Hauke Mehrtens)
- Directly add PCI resources (Hauke Mehrtens)
- Free resource list after registration (Hauke Mehrtens)
Freescale i.MX6 host bridge driver
- Add speed change timeout message (Troy Kisky)
- Rename imx6_pcie_start_link() to imx6_pcie_establish_link() (Bjorn Helgaas)
Freescale Layerscape host bridge driver
- Use dw_pcie_link_up() consistently (Bjorn Helgaas)
- Factor out ls_pcie_establish_link() (Bjorn Helgaas)
Marvell MVEBU host bridge driver
- Remove mvebu_pcie_scan_bus() (Yijing Wang)
NVIDIA Tegra host bridge driver
- Remove tegra_pcie_scan_bus() (Yijing Wang)
Synopsys DesignWare host bridge driver
- Consolidate outbound iATU programming functions (Jisheng Zhang)
- Use iATU0 for cfg and IO, iATU1 for MEM (Jisheng Zhang)
- Add support for x8 links (Zhou Wang)
- Wait for link to come up with consistent style (Bjorn Helgaas)
- Use pci_scan_root_bus() for simplicity (Yijing Wang)
TI DRA7xx host bridge driver
- Use dw_pcie_link_up() consistently (Bjorn Helgaas)
Miscellaneous
- Include <linux/pci.h>, not <asm/pci.h> (Bjorn Helgaas)
- Remove unnecessary #includes of <asm/pci.h> (Bjorn Helgaas)
- Remove unused pcibios_select_root() (again) (Bjorn Helgaas)
- Remove unused pci_dma_burst_advice() (Bjorn Helgaas)
- xen/pcifront: Don't use deprecated function pci_scan_bus_parented() (Arnd Bergmann)"
* tag 'pci-v4.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: pciehp: Inline the "handle event" functions into the ISR
PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
PCI: pciehp: Make queue_interrupt_event() void
PCI: xgene: Allow config access to Root Port even when link is down
PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
PCI: pciehp: Clean up debug logging
x86/PCI: Use host bridge _CRS info on systems with >32 bit addressing
PCI: imx6: Add #define PCIE_RC_LCSR
PCI: imx6: Use "u32", not "uint32_t"
PCI: Remove unused pci_scan_bus_parented()
xen/pcifront: Don't use deprecated function pci_scan_bus_parented()
PCI: imx6: Add speed change timeout message
PCI/ASPM: Simplify Clock Power Management setting
PCI: designware: Wait for link to come up with consistent style
PCI: layerscape: Factor out ls_pcie_establish_link()
PCI: layerscape: Use dw_pcie_link_up() consistently
PCI: dra7xx: Use dw_pcie_link_up() consistently
x86/PCI: Use host bridge _CRS info on Foxconn K8M890-8237A
PCI: pciehp: Wait for hotplug command completion where necessary
PCI: Remove unused pci_dma_burst_advice()
...
|
|
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
|
|
* acpi-pm:
ACPI / PM: Add missing pm_generic_complete() invocation
ACPI / PM: Turn power resources on and off in the right order during resume
ACPI / PM: Rework device power management to follow ACPI 6
ACPI / PM: Drop stale comment from acpi_power_transition()
* acpi-apei:
GHES: Make NMI handler have a single reader
GHES: Elliminate double-loop in the NMI handler
GHES: Panic right after detection
GHES: Carve out the panic functionality
GHES: Carve out error queueing in a separate function
* acpi-osl:
ACPI / osl: use same type for acpi_predefined_names values as in definition
* acpi-pci:
ACPI / PCI: remove stale list_head in struct acpi_prt_entry
|
|
* pci/host-xgene:
PCI: xgene: Allow config access to Root Port even when link is down
PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
* pci/hotplug:
PCI: pciehp: Inline the "handle event" functions into the ISR
PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
PCI: pciehp: Make queue_interrupt_event() void
PCI: pciehp: Clean up debug logging
|
|
The pciehp_handle_*() functions (pciehp_handle_attention_button(), etc.)
only contain a line or two of useful code, so it's clumsy to put
them in separate functions. All they so is add an event to a work queue,
and it's clearer to see that directly in the ISR.
Inline them directly into pcie_isr(). No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
Rename queue_interrupt_event() to pciehp_queue_interrupt_event() so we can
make it extern and call it from pcie_isr().
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
Nobody looks at the return value from queue_interrupt_event(), so errors
were silently ignored. Convert it to a "void" function and note the error
in the dmesg log.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
Previously, when a Root Port's link was down, we didn't allow config access
to the Root Port, which meant that if the Root Port led to an empty slot,
"lspci" didn't even show the Root Port.
Allow config access to Root Port even when link is down.
[bhelgaas: changelog, fold in unused var fix]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When a CPU reads the Vendor and Device ID of a non-existent device, the
controller should fabricate return data of 0xFFFFFFFF. Configuration
Request Retry Status (CRS) is not applicable in this case because the
device doesn't exist at all.
The X-Gene v1 PCIe controller has a bug in the CRS logic such that when CRS
is enabled, it fabricates return data of 0xFFFF0001 for this case, which
means "the device exists but is not ready." That causes the PCI core to
retry the read until it times out after 60 seconds.
Disable CRS capability advertisement by clearing the CRS Software
Visibility bit in the Root Capabilities Register.
[bhelgaas: changelog and comment]
Tested-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
|
|
The pciehp debug logging is overly verbose and often redundant. Almost all
of the information printed by dbg_ctrl() is also printed by the normal PCI
core enumeration code and by pcie_init().
Remove the redundant debug info.
When claiming a pciehp bridge, we print the slot characteristics, e.g.,
Slot #6 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
Add the Hot-Plug Capable and Hot-Plug Surprise bits to this information,
and print it all in the same order as lspci does.
No functional change except the message text changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
* pci/host-designware:
PCI: designware: Use iATU0 for cfg and IO, iATU1 for MEM
PCI: designware: Consolidate outbound iATU programming functions
PCI: designware: Add support for x8 links
* pci/host-designware-common:
PCI: designware: Wait for link to come up with consistent style
PCI: layerscape: Factor out ls_pcie_establish_link()
PCI: layerscape: Use dw_pcie_link_up() consistently
PCI: dra7xx: Use dw_pcie_link_up() consistently
PCI: imx6: Rename imx6_pcie_start_link() to imx6_pcie_establish_link()
* pci/host-generic:
of/pci: Fix pci_address_to_pio() conversion of CPU address to I/O port
* pci/host-imx6:
PCI: imx6: Add #define PCIE_RC_LCSR
PCI: imx6: Use "u32", not "uint32_t"
PCI: imx6: Add speed change timeout message
* pci/host-iproc:
PCI: iproc: Free resource list after registration
PCI: iproc: Directly add PCI resources
PCI: iproc: Add BCMA PCIe driver
PCI: iproc: Allow override of device tree IRQ mapping function
* pci/host-xgene:
arm64: dts: Add APM X-Gene PCIe MSI nodes
PCI: xgene: Add APM X-Gene v1 PCIe MSI/MSIX termination driver
|
|
Define PCIE_RC_LCSR and use it instead of the bare offset "0x80."
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use "u32", not "uint32_t", for consistency. Use "tmp", not "temp", for
consistency within the driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
|
|
* pci/aspm:
PCI/ASPM: Simplify Clock Power Management setting
PCI: Use dev->has_secondary_link to find downstream PCIe links
PCI/ASPM: Use dev->has_secondary_link to find downstream links
PCI: Add dev->has_secondary_link to track downstream PCIe links
PCI/ASPM: Remove redundant PCIe port type checking
PCI/ASPM: Drop __pci_disable_link_state() useless "force" parameter
* pci/enumeration:
PCI: Remove unused pci_scan_bus_parented()
xen/pcifront: Don't use deprecated function pci_scan_bus_parented()
PCI: designware: Use pci_scan_root_bus() for simplicity
PCI: tegra: Remove tegra_pcie_scan_bus()
PCI: mvebu: Remove mvebu_pcie_scan_bus()
* pci/hotplug:
PCI: pciehp: Wait for hotplug command completion where necessary
PCI: Propagate the "ignore hotplug" setting to parent
ACPI / hotplug / PCI: Check ignore_hotplug for all downstream devices
PCI: pciehp: Drop pointless label from pciehp_probe()
PCI: pciehp: Drop pointless ACPI-based "slot detection" check
* pci/misc:
PCI: Remove unused pci_dma_burst_advice()
PCI: Remove unused pcibios_select_root() (again)
PCI: Remove unnecessary #includes of <asm/pci.h>
PCI: Include <linux/pci.h>, not <asm/pci.h>
* pci/msi:
PCI/MSI: Remove unused pci_msi_off()
PCI/MSI: Drop pci_msi_off() calls from quirks
ntb: Drop pci_msi_off() call during probe
virtio_pci: drop pci_msi_off() call during probe
PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI
PCI/MSI: Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl()
PCI/MSI: Rename msi_set_enable(), msix_clear_and_set_ctrl()
* pci/resource:
PCI: Add pci_bus_addr_t
* pci/virtualization:
ACPI / PCI: Account for ARI in _PRT lookups
PCI: Move pci_ari_enabled() to global header
PCI: Add function 1 DMA alias quirk for Marvell 9120
PCI: Add ACS quirks for Intel 9-series PCH root ports
|
|
No one uses pci_scan_bus_parented() any more, remove it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use pci_scan_root_bus() instead of deprecated function
pci_scan_bus_parented().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: xen-devel@lists.xenproject.org
|
|
Currently, the timeout is never detected as count has a value of -1 if a
timeout happens, but the code is checking for 0. Also, this patch removes
the unneeded final wait if a timeout occurs.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1433543864-7252-1-git-send-email-troy.kisky@boundarydevices.com]
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Update the Link Control Enable Clock Power Management bit the same
way we update the ASPM Control bits, with a single call of
pcie_capability_clear_and_set_word().
No functional change; this just makes both paths use the same style.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
All the DesignWare-based host drivers loop waiting for the link to come up,
but they do it several ways that are needlessly different.
Wait for the link to come up in a consistent style across all the
DesignWare drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
All other DesignWare-based drivers have a *_establish_link() function.
This functionality is trivial for Layerscape, but factor out a
ls_pcie_establish_link() for consistency with the other drivers. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
All the other DesignWare-based drivers use dw_pcie_link_up(), so use it in
this driver, too, for consistency. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
We already use dw_pcie_link_up() once in dra7xx_pcie_establish_link(), but
we duplicate its code later. Use dw_pcie_link_up() for consistency. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously. Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed. In cases
where we need that state change to be enabled, we must still wait for
completion. For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection. If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.
Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion. The following
functions are returned to their previous behavior:
pciehp_power_on_slot
pciehp_power_off_slot
pcie_disable_notification
pciehp_reset_slot
The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on. pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected. And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.
Fixes: 3461a068661c ("PCI: pciehp: Wait for hotplug command completion lazily")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
|
|
struct timeval uses a 32-bit field for representing seconds, which
will overflow in the year 2038 and beyond. Replace struct timeval with
64-bit ktime_t which is 2038 safe. This is part of a larger effort to
remove instances of 32-bit timekeeping variables (timeval, time_t and
timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Rename imx6_pcie_start_link() to imx6_pcie_establish_link() to follow the
convention of other DesignWare-based host drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
|
|
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.
In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus. Even if we'd had the correct size, the end would
have been off by one.
Preserve the resource size when we adjust its alignment.
[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
David Ahern reported that d63e2e1f3df9 ("sparc/PCI: Clip bridge windows
to fit in upstream windows") fails to boot on sparc/T5-8:
pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)
The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3df9 added new checking that
tripped over this mismatch.
Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.
[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at
least as wide as dma_addr_t, documentation]
Fixes: d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Fixes: 23b13bc76f35 ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com
Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231
Reported-by: David Ahern <david.ahern@oracle.com>
Tested-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: stable@vger.kernel.org # v3.19+
|
|
pci_ari_enabled() is useful outside of drivers/pci, particularly for
deriving INTx routing via ACPI _PRT, so move it to the global header.
Also convert to bool return.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Don Dutile <ddutile@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Previously we assumed that PCIe Root Ports and Downstream Ports had Links
on their secondary side. That is true in most systems, but it is possible
to connect a switch with either an Upstream or a Downstream Port leading
downstream.
Instead of relying on the component type to identify devices that have
links leading downstream, use the "dev->has_secondary_link" field.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The resource list is only used in the setup process and was never freed.
pci_add_resource() allocates a memory area to store the list item.
Fix the memory leak.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
|
|
The struct iproc_pcie.resources member was pointing to a stack variable and
is invalid after the registration function returned.
Remove this pointer and add a parameter to the function.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
|
|
In d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), it stores additional alignment in realloc_head and takes
this into consideration for assignment.
After getting the additional alignment, it reorders the head list so
resources with bigger alignment are ahead of resources with smaller
alignment. It does this by iterating over the head list and inserting
ahead of any resource with smaller alignment. This should be done for the
first occurrence, but the code currently iterates over the whole list.
Fix this by terminating the loop when we find the first smaller resource in
the head list.
[bhelgaas: changelog]
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After b97ea289cf6a ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to:
pci_create_root_bus()
pci_scan_child_bus()
Use pci_scan_root_bus() to simplify the code.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Mohit Kumar <mohit.kumar@st.com>
|
|
After b97ea289cf6a ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to tegra_pcie_scan_bus().
Remove tegra_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path.
[bhelgaas: changelog]
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
After b97ea289cf6a ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to mvebu_pcie_scan_bus().
Remove mvebu_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path. We also need to use pci_common_init_dev()
instead of pci_common_init() so we can supply the host bridge device
pointer.
[bhelgaas: changelog]
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>
|
|
We allocate pcie_link_state for the component at the upstream end of a
Link. Previously we did this by allocating pcie_link_state for Root Ports
and Downstream Ports. This works fine for the typical topology:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Upstream Port [bridge to bus 03]
03:00.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
However, it is possible to have a Root Port connected to a Downstream Port
instead of an Upstream Port, as in Robert White's ATCA system:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Downstream Port [bridge to bus 03]
03:01.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
In this topology, we wrongly allocated pcie_link_state for the 02:00.0
Downstream Port, which is actually the *downstream* end of a link. This
led to the following NULL pointer dereference when we tried to connect this
link into the tree of links starting at the 00:1c.0 Root Port:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff81550324>] pcie_aspm_init_link_state+0x744/0x850
Hardware name: Kontron B3001/B3001, BIOS 4.6.3 08/07/2012
Call Trace:
[<ffffffff8153b865>] pci_scan_slot+0xd5/0x120
[<ffffffff8153ca1d>] pci_scan_child_bus+0x2d/0xd0
...
Instead of relying on the component type to identify the upstream end of a
link, use the "dev->has_secondary_link" field.
This means it's now possible for an Upstream Port to have a link on its
secondary side, so alloc_pcie_link_state() needs to connect links
originating from both Upstream and Downstream Ports into the tree.
[bhelgaas: changelog, add comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361
Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the
ignore_hotplug setting of the device to its parent bridge in case hotplug
notifications related to the graphics adapter switching are given for the
bridge rather than for the device itself (they need to be ignored in both
cases).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891
Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927
Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Reported-and-tested-by: tiagdtd-lava <tiagdtd-lava@yahoo.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
|
|
If the ignore_hotplug flag is set for a PCI device without an ACPI
companion and a bus check notification is received for an ancestor bridge
that is not the device's parent, ACPIPHP will ignore that flag.
Namely, in that case acpiphp_check_bridge() is called for the target bridge
and if all of the devices immediately below the bridge are still present,
trim_stale_devices() will be called for each of them. That function
recursively walks the hierarchy downwards and removes device objects
corresponding to devices that don't appear to be present any more.
Unfortunately, it only checks ignore_hotplug for devices having ACPI
companions, so it will remove the others (if they don't respond) regardless
of the ignore_hotplug value.
Fix the problem by making trim_stale_devices() take ignore_hotplug into
consideration regardless of whether or not an ACPI companion is present for
the device it has been called for.
[bhelgaas: This may fix bug 61891, depending on whether the bridge above a
device is removed along with the device]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The err_out_none label in pciehp_probe() only leads to a return statement,
so use return statements instead of jumps to it and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
A PCIe Port is an interface to a Link. A Root Port is a PCI-PCI bridge in
a Root Complex and has a Link on its secondary (downstream) side. For
other Ports, the Link may be on either the upstream (closer to the Root
Complex) or downstream side of the Port.
The usual topology has a Root Port connected to an Upstream Port. We
previously assumed this was the only possible topology, and that a
Downstream Port's Link was always on its downstream side, like this:
+---------------------+
+------+ | Downstream |
| Root | | Upstream Port +--Link--
| Port +--Link--+ Port |
+------+ | Downstream |
| Port +--Link--
+---------------------+
But systems do exist (see URL below) where the Root Port is connected to a
Downstream Port. In this case, a Downstream Port's Link may be on either
the upstream or downstream side:
+---------------------+
+------+ | Upstream |
| Root | | Downstream Port +--Link--
| Port +--Link--+ Port |
+------+ | Downstream |
| Port +--Link--
+---------------------+
We can't use the Port type to determine which side the Link is on, so add a
bit in struct pci_dev to keep track.
A Root Port's Link is always on the Port's secondary side. A component
(Endpoint or Port) on the other end of the Link obviously has the Link on
its upstream side. If that component is a Port, it is part of a Switch or
a Bridge. A Bridge has a PCI or PCI-X bus on its secondary side, not a
Link. The internal bus of a Switch connects the Port to another Port whose
Link is on the downstream side.
[bhelgaas: changelog, comment, cache "type", use if/else]
Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Marvell 9120 SATA controller has the same issue as a number of others, so
use the same quirk for this one. The other quirks were added by
cc346a4714a5 ("PCI: Add function 1 DMA alias quirk for Marvell devices").
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
|
Bjorn Helgaas
Yijing Wang
Linus Torvalds
Pratyush Anand
Thomas Gleixner
Rafael J. Wysocki
Duc Dang
Arnd Bergmann
Troy Kisky
Alex Williamson
Tina Ruchandani
Yinghai Lu
Hauke Mehrtens
Wei Yang
Sakari Ailus