| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds extended PCIe PHY functions for the Amlogic G12A
USB3+PCIE Combo PHY to support reset, power_on and power_off for
PCIe exclusively.
With these callbacks, we can handle all the needed operations of the
Amlogic PCIe controller driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
|
|
Locking is not needed for the phy_g12a_usb3_pcie_cr_bus_read/write() and
currently it causes the following BUG because of the usage of the
regmap_read_poll_timeout() running in spinlock_irq, configured by regmap fast_io.
Simply disable locking in the cr_regmap config since it's only used from the
PHY init callback function.
BUG: sleeping function called from invalid context at drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c:85
in_atomic(): 1, irqs_disabled(): 128, pid: 60, name: kworker/3:1
[snip]
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x190
show_stack+0x14/0x20
dump_stack+0x90/0xb4
___might_sleep+0xec/0x110
__might_sleep+0x50/0x88
phy_g12a_usb3_pcie_cr_bus_addr.isra.0+0x80/0x1a8
phy_g12a_usb3_pcie_cr_bus_read+0x34/0x1d8
_regmap_read+0x60/0xe0
_regmap_update_bits+0xc4/0x110
regmap_update_bits_base+0x60/0x90
phy_g12a_usb3_pcie_init+0xdc/0x210
phy_init+0x74/0xd0
dwc3_meson_g12a_probe+0x2cc/0x4d0
platform_drv_probe+0x50/0xa0
really_probe+0x20c/0x3b8
driver_probe_device+0x68/0x150
__device_attach_driver+0xa8/0x170
bus_for_each_drv+0x64/0xc8
__device_attach+0xd8/0x158
device_initial_probe+0x10/0x18
bus_probe_device+0x90/0x98
deferred_probe_work_func+0x94/0xe8
process_one_work+0x1e0/0x338
worker_thread+0x230/0x458
kthread+0x134/0x138
ret_from_fork+0x10/0x1c
Fixes: 36077e16c050 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use devm_clk_get_optional() to get optional clock
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.
As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).
This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).
[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
dwc3 controller only has USB2 ports enabled) we need to initialize the
USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
initialization high-speed USB devices (especially USB hard disks and
thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
USB2 PHY between host and peripheral (aka device) mode. an interrupt
can be used to detect changes between host and device mode.
There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
logic (on the GXL and GXM SoCs these are the same clock and reset line
as for the USB3 PHY itself, but Amlogic sees this as two different
components - even though they share the same register space - so they
have to be passed individually to allow specifying different inputs on
other SoCs if needed)
- the interrupt for the OTG detection logic
The whole OTG detection logic is not implemented yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The U2P_R2 register provides "test mode" functionality for bits 17:0.
These are only used during SoC development and should be left untouched
on production SoC versions.
Rename these register definitions to indicate that these are for "test
mode" only.
While here, also merge the definitions for U2P_R2_DATA_IN_MASK and
U2P_R2_DATA_IN_EN_MASK (bits 0:7) because Amlogic's internal
documentation suggests that these bits belong together. The old
definition was not taken from the documentation but rather from a struct
definition in the Amlogic GPL kernel sources.
No functional changes.
Suggested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The USB2 PHY can switch between PHY_MODE_USB_HOST and
PHY_MODE_USB_DEVICE. However, it cannot do it on it's own since it
requires re-routing of the corresponding USB pins from dwc3 (which is
used for host-mode) to dwc2 (which is used for device-mode).
Thus we don't need to auto-detect the mode based on the USB controller,
which simplifies the driver code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The Meson GXL USB2 PHYs require an additional clock (USB) which has to
be enabled. If that clock is disabled then all PHY registers read 0x0.
Luckily for us that clock is always enabled (either by harddware
defaults, the bootrom, or any of the bootloaders before u-boot/BL3-3).
The OTG capable USB2 PHY additionally has a reset line (USB_OTG, which
is shared with other components, such as the USB3 PHY for example).
Extend the driver so it handles this clock and the shared reset line.
We only trigger the reset during the .init phase since it's a shared
reset line, so triggering it during the driver's .reset implementation
would effectively also only trigger it once anyways.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
devm_phy_create can return -EPROBE_DEFER if the phy-supply is not ready
yet. Silence this warning as the driver framework will re-attempt
registering the PHY - this second try works without any errors. So only
log actual errors to keep the kernel log free of misleading error
messages.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Meson8 uses the same USB PHY as found on the Meson8b and GXBB SoCs. Add
a new of_device_id to indicate this. Also update the Kconfig option and
MODULE_DESCRIPTION accordingly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
The USB2 PHY is a simple PHY which only has a few registers to configure
the mode (host/device) and a reset register (to enable/disable the PHY).
Unfortunately there are no datasheets available for this PHY. The driver
was written by reading the code from Amlogic's GPL kernel sources and
by analyzing the registers on an actual GXL and GXM device running the
kernel that was shipped on the boards I have.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Adding vendor specific directories in phy to group
phy drivers under their respective vendor umbrella.
Also updated the MAINTAINERS file to reflect the correct
directory structure for phy drivers.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
Neil Armstrong
Greg Kroah-Hartman
Thomas Gleixner
Chunfeng Yun
Grygorii Strashko
Martin Blumenstingl
Vivek Gautam