| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
|
|
For V4 QMP UFS Phy, we need to assert reset bits, configure the phy and
then deassert it, so add the QPHY_SW_RESET register which does this.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
SM8150 QMPY phy for UFS and onwards the PHY_SW_RESET is present in PHY's
PCS register so we should not mark no_pcs_sw_reset for sm8150 and
onwards
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We already write to QPHY_POWER_DOWN_CONTROL in qcom_qmp_phy_com_init()
before invoking qcom_qmp_phy_configure() so remove the duplicate write.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We already define register offsets so use them in register layout.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Clang warns:
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:83:4: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
^
../drivers/phy/qualcomm/phy-qcom-apq8064-sata.c:80:3: note: previous
statement is here
if (readl_relaxed(addr) & mask)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 1de990d8a169 ("phy: qcom: Add driver for QCOM APQ8064 SATA PHY")
Link: https://github.com/ClangBuiltLinux/linux/issues/816
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch corrects the SPDX License Identifier style in
header files related to PHY drivers for Qualcomm platforms.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register
defines and support for SM8150 QMP UFS PHY.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Despite extensive testing of commit 885bd765963b ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".
Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.
Cc: stable@vger.kernel.org
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 885bd765963b ("phy: qcom-qmp: Correct READY_STATUS poll break condition")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence create a new label,
err_node_put, that puts the previous node (child) before returning the
required value. Also include the statement pm_runtime_disable() under
this label in order to avoid repetition among mid-loop return
conditions. Edit the mid-loop return statements to instead go to this
new label err_node_put.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
|
|
Kishon writes:
phy: for 5.2-rc
*) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124
*) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210
*) Minor fixes: fix memory leaks at error path and addresses coverity.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: tegra: xusb: Add Tegra210 PLL power supplies
phy: tegra: xusb: Add Tegra124 PLL power supplies
dt-bindings: phy: tegra-xusb: List PLL power supplies
phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal
phy: renesas: rcar-gen2: Fix memory leak at error paths
phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
|
|
readl_poll_timeout() calls usleep_range() to sleep between reads.
usleep_range() doesn't work efficiently for tiny values.
Raise the polling delay in qcom_qmp_phy_enable() to bring it in line
with the delay in qcom_qmp_phy_com_init().
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
'mask_com_pcs_ready' is only useful if 'has_phy_com_ctrl' is true.
Since msm8998_pciephy_cfg.has_phy_com_ctrl is false, let's drop
msm8998_pciephy_cfg.mask_com_pcs_ready altogether.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
After issuing a PHY_START request to the QMP, the hardware documentation
states that the software should wait for the PCS_READY_STATUS to become
1.
With the introduction of commit c9b589791fc1 ("phy: qcom: Utilize UFS
reset controller") an additional 1ms delay was introduced between the
start request and the check of the status bit. This greatly increases
the chances for the hardware to actually becoming ready before the
status bit is read.
The result can be seen in that UFS PHY enabling is now reported as a
failure in 10% of the boots on SDM845, which is a clear regression from
the previous rare/occasional failure.
This patch fixes the "break condition" of the poll to check for the
correct state of the status bit.
Unfortunately PCIe on 8996 and 8998 does not specify the mask_pcs_ready
register, which means that the code checks a bit that's always 0. So the
patch also fixes these, in order to not regress these targets.
Fixes: 73d7ec899bd8 ("phy: qcom-qmp: Add msm8998 PCIe QMP PHY support")
Fixes: e78f3d15e115 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org
Cc: Evan Green <evgreen@chromium.org>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The error return from the call to clk_prepare_enable is not being assigned
to variable ret even though ret is being used to check if the call failed.
Fix this by adding in the missing assignment.
Addresses-Coverity: ("Logically dead code")
Fixes: 891a96f65ac3 ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The Qualcomm PCIe2 PHY is based on design from Synopsys and found in
several different platforms where the QMP PHY isn't used.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
|
|
Documentation for this PHY, and the proper configuration settings,
is *not* publicly available. Therefore the initialization sequence
is copied wholesale from downstream:
https://source.codeaurora.org/quic/la/kernel/msm-4.4/tree/arch/arm/boot/dts/qcom/msm8998-v2.dtsi?h=LE.UM.1.3.r3.25#n372
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use devm_clk_get_optional() to get optional clock
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fix sparse warning:
drivers/phy/qualcomm/phy-qcom-ufs.c:462:6:
warning: symbol 'ufs_qcom_phy_disable_iface_clk' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use same init sequence as sdm845.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
MSM8998 contains one QUSB2 PHY which is very similar to the existing
sdm845 support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
MSM8998 contains a single QMP v3 USB3 phy similar to the existing sdm845
support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The private copy of readl_poll_timeout is no longer needed.
Use the implementation in iopoll.h instead.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
I submitted this driver several times before it got accepted. The
first series hasn't been accepted but the DTS binding did made it.
I then made a second series that added generic reset support to the
PHY core, this in turn required a change to the DT binding. This
second series seemed to have been ignored, so I did a third one
without the change to the PHY core and the DT binding update, and this
last attempt finally made it.
But two months later the DT binding update from the second series has
been integrated too. So now the driver doesn't match the binding and
the only DTS using it. This patch fix the driver to match the new
binding.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In the power on function the error path doesn't return the suspend
override to its proper state. It should should deassert this reset
line to enable the suspend override.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Register a simple clock provider for the PHY pipe clock sources so that
device tree users can point at these clocks via phandles to the lane
nodes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Utilize the newly fixed up DT bindings to get the tx2 and rx2 register
regions for the second lane of dual-lane PHYs. Before this change,
the driver was simply using lane one's register region and adding
0x400, which reached well beyond the DT-specified register
allocation. This would have been a crash were it not for the page size
on ARM64. Fix the driver not to rely on the magic of virtual memory by
using the newly specified DT register regions for tx2 and rx2.
In order to support existing device trees, this change also contains a
fallback mode for when those new register regions don't exist, which
reverts to the original behavior of overreaching and prints a complaint.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.
As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).
This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).
[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Tune1 register on sdm845 is used to update HSTX_TRIM with fused
setting. Enable same by specifying update_tune1_with_efuse flag
for sdm845, otherwise driver ends up programming tune2 register.
Fixes: ef17f6e212ca ("phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fix HSTX_TRIM tuning logic which instead of using fused value
as HSTX_TRIM, incorrectly performs bitwise OR operation with
existing default value.
Fixes: ca04d9d3e1b1 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fork out separate configs for 14nm and 20nm qcom ufs qmp phys
to declare the 20nm phy as broken.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The host makes direct calls into phy using ufs_qcom_phy_*()
APIs. These APIs are only defined for 20nm qcom-ufs-qmp phy
which is not being used by any architecture as yet. Future
architectures too are not going to use 20nm ufs phy.
So remove these ufs_qcom_phy_*() calls from host to let further
change declare the 20nm phy as broken.
Also remove couple of stale enum defines for ufs phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Remove ufs_qcom_phy_enable/(disable)_dev_ref_clk() that
are not being used by any code.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add UFS PHY support to make SDM845 UFS work with common PHY framework.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Move MSM8996 specific PHY vreg list struct name to a genernal one as it is
used by all PHYs. Add a specific field to handle dual lane situation.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
All PHYs should be powered on before register configuration starts. And
only PCIe PHYs need an extra power control before deasserts reset state.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The -EPROBE_DEFER virus demands special case code to avoid printing
error messages when the error is only -EPROBE_DEFER. Spread the virus
to a new host: qusb2_phy_probe(). Specifically handle when our
regulators might not be ready yet.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The -EPROBE_DEFER virus demands special case code to avoid printing
error messages when the error is only -EPROBE_DEFER. Spread the virus
to a new host: qcom_qmp_phy_probe(). Specifically handle when our
regulators might not be ready yet.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
There are two QUSB2 PHYs present on sdm845. In order
to improve eye diagram for both the PHYs some parameters
need to be changed. Provide device tree properties to
override these from board specific device tree files.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
Greg Kroah-Hartman
Vinod Koul
Nathan Chancellor
Bjorn Andersson
Nishad Kamdar
Stephan Gerhold
Nishka Dasgupta
Marc Gonzalez
Thomas Gleixner
Colin Ian King
Linus Torvalds
Chunfeng Yun
Evan Green
YueHaibing
Jeffrey Hugo
Alban Bedel
Grygorii Strashko
Manu Gautam
Vivek Gautam
Can Guo
Rob Herring
Douglas Anderson
Gustavo A. R. Silva