| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Update header inclusion block to reflect all direct dependencies
that are being involved in pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
intel_pinctrl_get_soc_data() helper can be used in few driver instead of
open-coded variants. Thus, extract it as a standalone API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
By one of the previous clean up change we got a temporary variable to hold
a device pointer. It can be utilized in other calls in the ->probe() and
save a bit of LOCs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now when all preparations are done we may easily switch to use
struct intel_pinctrl instead of custom one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This is a preparatory patch for bigger clean up pending for Cherryview driver.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There is no more .groups member in struct chv_pinctrl,
drop associated comment because it's not applicable anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This driver adds pinctrl/GPIO support for Intel Emmitsburg PCH. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1].
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Intel Tiger Lake-H has different pin layout than the -LP variant
so add support for this to the existing Tiger Lake driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
It is useful to control I²S bus 2 pins if we would like to connect
an audio codec.
Reported-by: mouse <xllacyx@gmail.com>
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Some of the pin names were provided officially to the customers
in different spelling. We update pin names in accordance with
the official list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5cc ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812fe3 ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we dependent on ACPI, there is no need to use ACPI_PTR()
which is a no-op in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Introduce couple of helpers to enable or disable input. i.e.
lp_gpio_enable_input() and lp_gpio_disable_input().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make use of for_each_requested_gpio_in_range() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In a code like
if (...) {
...
goto label;
} else {
...
}
the 'else' keyword is redundant. Get rid of it for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases lock covers unneeded calls and operations.
Reduce scope of the lock in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We have some data structures duplicated across the drivers.
Let's deduplicate them by using struct intel_pinctrl_soc_data,
struct intel_community and struct intel_pinctrl_context that
are being provided by pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Individual drivers may install ACPI OpRegion handlers based on
address space ID which differs from community to community.
Add special field in the struct intel_community for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Some of the pin control devices may not be capable to generate IRQ
per each pin in the community. Allow individual drivers to define
total amount of IRQs per community.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
chv_writel() is now solely used for cases where we write data
to the PAD registers. In order to simplify callers, calculate
register address inside chv_writel().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Pin control device and effectively the single community in it has
a set of common registers. It's good to have a helpers to IO on them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There are plenty of places where we call
readl(chv_padreg(pctrl, offset, ...));
Replace them with newly introduced chv_readl() helper
chv_readl(pctrl, offset, ...);
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It's common across the drivers to use the (pin_base, npins) pair to describe
community characteristics. Thus, move them in the struct intel_community
to be closer to each other.
While at it, add a blank line to cut driver usable fields from what core
reserves for itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that most of the drivers, that are using struct intel_community,
utilize gpps rather than gpp_size. Update comment accordingly.
While here, correct the description of gpp_size, i.e. remove double space
and drop redundant 'etc.' part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e859 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b00 ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no need to repeat functionality of platform_get_irq_optional()
in the driver. Replace it with explicit call to the helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
This driver adds pinctrl/GPIO support for Intel Jasper Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases not the first group would like to have GPIO base to be 0.
It's not possible right now due to 0 has special meaning already. Thus,
introduce a new flag to allow drivers to force GPIO base to be 0 on
a certain group. It's assumed that it can be only one group per device
with such flag enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we have a generic flag for special GPIO base treatment,
use it in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Few drivers are using the same flag to tell Intel pin control core
how to interpret GPIO base.
Provide a generic flags so all drivers can use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149de ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a76 ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It appears that SPT-H variant has different offset for PAD locking registers.
Fix it here.
Fixes: 551fa5801ef1 ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Turns out that Tiger Lake GPIO will be enumerated using _HID method where
there is only a single ACPI device and multiple BARs so rework the driver
to support that scheme instead.
Fixes: c9ccf71fc807 ("pinctrl: intel: Add Intel Tiger Lake pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Intel Coffee Lake-S PCH has the same GPIO hardware than Sunrisepoint-H
PCH but the ACPI ID is different. Add this new ACPI ID to the list of
supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
Hans de Goede
Andy Shevchenko
Gustavo A. R. Silva
Mika Westerberg
Grace Kao