| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5.
Change the current code that uses IRQ bank base to a IRQ bank map, in
order to support the case that holes exist among IRQ banks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5. Some
refactors in the sunxi pinctrl framework are needed.
This commit introduces a IRQ bank conversion function, which replaces
the "(bank_base + bank)" code in IRQ register access.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As the new H6 SoC has holes in the IRQ registers, refactor the IRQ
related register function for getting the full pinctrl desc structure.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Our pinctrl device should have had strict set all along. However, it wasn't
the case, and most of our old device trees also have a pinctrl group in
addition to the GPIOs properties, which mean that we can't really turn it
on now.
All our new SoCs don't have that group, so we should still enable that mode
on the newer one though.
In order to enable it by default, add a flag that will allow to disable
that mode that should be set by pinctrl drivers that cannot be migrated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
into A10 driver, and add R40 support into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The sunxi pinctrl driver currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A31s is a trimmed down version of the A31. Some hardware blocks
are removed, thus not available for muxing on the external pins.
Some external pins were directly removed.
This makes it easy to support the A31s pin controller with the A31
driver. We just mark the pins and functions that were trimmed as
A31 only.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.
Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).
In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.
Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The sunxi pinctrl driver only caches whatever pinconf setting was last
set on a given pingroup. This is not particularly helpful, nor is it
correct.
Fix this by actually reading the hardware registers and returning
the correct results or error codes. Also filter out unsupported
pinconf settings. Since this driver has a peculiar setup of 1 pin
per group, we can support both pin and pingroup pinconf setting
read back with the same code. The sunxi_pconf_reg helper and code
structure is inspired by pinctrl-msm.
With this done we can also claim to support generic pinconf, by
setting .is_generic = true in pinconf_ops.
Also remove the cached config value. The behavior of this was never
correct, as it only cached 1 setting instead of all of them. Since
we can now read back settings directly from the hardware, it is no
longer required.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.
Missed edges seem to be buffered, so this does not introduce a race
condition.
I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A80 R-PIO controller has one more bank that what we've seen so far, add the
PN pin bank.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A23 and A31 support multiple interrupt banks. Support it by adding a linear
domain covering all the banks. It's trickier than it should because there's an
interrupt per bank, so we have multiple interrupts using the same domain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A31 and A23, unlike the other Allwinner SoCs, have several interrupts banks
and parent interrupts, while the other only have up to 32 interrupts in a
single bank and a single parent interrupt.
Start supporting it by introducing a function macro to declare irq functions
and their banks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This will allow to have multiple drivers using the same core code, and
eventually, retire pinctrl-sunxi-pins.h
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
We previously had an evergrowing (and exhaustive) list of the pins that could
be used on any Allwinner SoCs. These defines were then used by each pinctrl
driver to declare the list of functions for this pin. Since it's pretty much
all boilerplate, we can remove it just by a single macro.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This will allow to create numerous files without crippling the main pinctrl
directory.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
Icenowy Zheng
Maxime Ripard
Julia Cartwright
Chen-Yu Tsai
Hans de Goede