| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
|
|
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.
It was suggested to combine this functionality with the current ds2782
driver. Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.
[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Avoid to get platform_data from parent device. Get it from mfd cell
device instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Fix rated capacity of the HP iPAQ hx4700 3.7V 1800mAh (359113-001) battery. For this battery the value of the rated capacity EEPROM register at 0x32 is 7; thus rated_capacities[7] = 1800.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Fix indexing of the 4 active full EEPROM registers. The indexing was out by 1, accessing the EEPROM registers at 0x23 to 0x26 instead of 0x22 to 0x25.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
In 2008 Masashi YOKOTA <yokota@pylone.jp> created the virtual
battery driver found here:
http://downloads.pylone.jp/src/virtual_battery/virtual_battery-0.0.1.tar.bz2
It found use out of tree, but was never merged upstream.
Since then the test_power driver has been merged, which provides
very similar functionality.
This patch extends the test_power driver to be more dynamic
at runtime, by merging portions of the Virtual Battery Driver
by Masashi YOKOTA.
With this patch, I can tweak the values in:
/sys/module/test_power/parameters/* and watch the behavior of
the gnome power managment daemon or other battery UI software.
CC: Anton Vorontsov <cbouatmailru@gmail.com>
CC: Akihiro MAEDA <sola.1980.a@gmail.com>
CC: Masashi YOKOTA <yokota@pylone.jp>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This patch fix using correct property POWER_SUPPLY_PROP_CYCLE_COUNT
for cycle count instead POWER_SUPPLY_PROP_CHARGE_COUNTER
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Fast-forwarded to current state of Linus' tree as there are patches to be
applied for files that didn't exist on the old branch.
|
|
S390 is special as it doesn't have IRQ lines, so these errors pop up:
drivers/built-in.o: In function 'max8903_remove':
drivers/power/max8903_charger.c:355: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:357: undefined reference to 'free_irq'
drivers/power/max8903_charger.c:359: undefined reference to 'free_irq'
This commit fixes the issue by making the driver depend on
GENERIC_HARDIRQS feature.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The ISP1704/1707 chip can be put to full power down
state by asserting the CHIP_SEL line. This patch enables
platform or board specific hooks to put the device into
power down mode in case not needed.
This patch is a preparation for enabling this powering
routine in n900 (rx-51) devices.
Thanks to Heikki Krogerus for helping out with the patch.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Gpio charger should notify if the gpio state had changed
during suspend. This will send a CHANGED event each time
the system resumes, ensuring a plug/unplug of the charger
is not missed.
Signed-off-by: Benson Leung <bleung@chromium.org>
Acked-By: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
MAX8903 is an integrated battery charger and selector with two
power inputs (USB and AC adapter). This driver enables the charger,
handles interrupts, and provides power-supply-class information to
userland.
Tested on Exynos4 NURI / S5PC210 SLP7 boards.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
* git://git.infradead.org/battery-2.6: (30 commits)
bq20z75: Fix time and temp units
bq20z75: Fix issues with present and suspend
z2_battery: Fix count of properties
s3c_adc_battery: Fix method names when PM not set
z2_battery: Add MODULE_DEVICE_TABLE
ds2782_battery: Add MODULE_DEVICE_TABLE
bq20z75: Add MODULE_DEVICE_TABLE
power_supply: Update power_supply_is_watt_property
bq20z75: Add i2c retry mechanism
bq20z75: Add optional battery detect gpio
twl4030_charger: Make the driver atomic notifier safe
bq27x00: Use single i2c_transfer call for property read
bq27x00: Cleanup bq27x00_i2c_read
bq27x00: Minor cleanups
bq27x00: Give more specific reports on battery status
bq27x00: Add MODULE_DEVICE_TABLE
bq27x00: Add new properties
bq27x00: Poll battery state
bq27x00: Cache battery registers
bq27x00: Add bq27000 support
...
|
|
mfd_get_cell returns a const, so change the jz4740 clients to store
a const mfd cell. This silences type mismatch warnings.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Corrected temperature and time to empty/full conversions.
Temperature is in 0.1°C, time is in seconds.
Corrected units in comment. "Convert to µWh."
Signed-off-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
There are a few issues found around the battery not being present. If the
battery isn't present, then a few undesirable things happen. The first was
excessive reporting of failed properties. This was fixed by instead
returning ENODATA for all properties other than PRESENT if the battery
isn't present. That way the callers can identify the difference between a
failure and the battery not being there.
The next issue was in the suspend logic. It was found that if the battery
wasn't present, then it would return a failure, preventing the system from
going into suspend. If there is no battery present, the io is expected to
fail, so in that case, we shouldn't return the failure and just
acknowledge that it was expected.
I also found that when a gpio was used, i didn't maintain the internal
is_present state properly. I added a set of that to fix that.
Lastly, the code to see io's fail and figure out that the battery isn't
present when not using a gpio had a problem. In that code, it looked for
the read to fail and if it did, then handled it. The problem is that in
function to get the property, it first writes a value and that write can
fail, causing the code to never reach the logic after the read. Fix is
to move the logic till after the write.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
PROP_STATUS property was not counted, as result VOLTAGE_MIN property is
missing in sysfs. Fix it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
s3c_adc_battery declares wrong method names when CONFIG_PM is not set.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:aer915 z2_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds2786 ds2782_battery
alias i2c:ds2782 ds2782_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:bq20z75 bq20z75
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Adding support for an optional gpio for battery detection. This is
passed in through the i2c platform data. It also accepts another
field, battery_detect_present to signify the gpio state which means
the battery is present, either 0 (low) or 1 (high).
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
|
|
This queues work from the otg notification where the
i2c operations can be safely made. Needed for atomic otg
notifiers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Doing this by using 2 calls sometimes results in unexpected
values being returned on OMAP3 i2c controller.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
Some minor stylistic cleanups.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
The current code only reports whether the battery is charging or
discharging. But the battery also reports whether it is fully charged,
furthermore by look at if the battery is supplied we can tell whether it
is discharging or not charging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch adds MODULE_DEVICE_TABLE for module bq27x00_battery.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch add support for reporting properties
POWER_SUPPLY_PROP_CHARGE_NOW, POWER_SUPPLY_PROP_CHARGE_FULL,
POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
POWER_SUPPLY_PROP_CHARGE_COUNTER, POWER_SUPPLY_PROP_ENERGY_NOW in
module bq27x00_battery.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch adds support for polling the battery state and generating a
power_supply_changed() event if it has changed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch adds a register cache to the bq27x00 battery driver.
Usually multiple, if not all, power_supply properties are queried at once,
for example when an uevent is generated. Since some registers are used by
multiple properties caching the registers should reduce the number of
reads.
The cache is valid for 5 seconds this roughly matches the internal update
interval of the current register for the bq27000/bq27200.
Fast changing properties(*_NOW) which can be obtained by reading a single
register are not cached.
It will also be used in the follow up patch to check if the battery status
has been changed since the last update to emit power_supply_changed events.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch adds support for the bq27000 battery to the bq27x00 driver.
The bq27000 is similar to the bq27200 except that it uses the HDQ bus
instead of I2C to communicate with the host system.
The driver is implemented as a platform driver. The driver expects to be
provided with a read callback function through its platform data. The read
function is assumed to do the lowlevel HDQ handling and read out the value
of a certain register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch simplifies the drivers data structure and moves code to be
shared by the bq27000 and bq27200/bq27500 init functions into a common
function.
This patch has no functional changes, it only moves code around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch changes get_property callback of the bq27x00 battery to return
-ENODEV for properties other then the PROP_PRESENT if the battery is not
present.
The power subsystem core expects a driver to behave that way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
According to the bq27000 datasheet the current should be calculated by
the following formula:
current = AI * 3570 / 20
This patch adjust the drivers code accordingly.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch improves the precession of the temperature property of the
bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the
last decimal digit. This patch fixes it by multiplying before dividing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
This patch adds the type property to the bq27x00 battery driver.
All bq27x00 are lithium ion batteries.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
Calling device_add causes an inital uevent for that device to be generated.
The power_supply uevent function calls the drivers get_property function,
which might causes the driver to update its state, which again might
causes the driver to call power_supply_changed(). Since the power_supplys
changed_work has not been initialized at this point the behavior is
undefined and can result in an OOPS.
This patch fixes the issue by initializing the power_supplys changed_work
prior to adding the power_supplys device to the device tree.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
Sometimes a driver can not report a meaningful value for a certain property
and returns -ENODATA.
Currently when generating a uevent and a property return -ENODATA it is
treated as an error an no uevent is generated at all. This is not an
desirable behavior.
This patch adds a special case for -ENODATA and ignores properties which
return this error code when generating the uevent.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
Add new trigger to power_supply LEDs. It will blink when battery is
charging, and stay solid when battery is charged. It's usefull to
indicate battery state when there's only one LED available.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Adding support for charge properties for gas gauge.
Also ensuring that battery mode is correct now for energy as well as
charge properties by setting it on the fly.
I also added 2 functions to power_supply.h to help identify the units for
specific properties more easily by power supplies.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
* git://git.infradead.org/battery-2.6: (21 commits)
power_supply: Add MAX17042 Fuel Gauge Driver
olpc_battery: Fix up XO-1.5 properties list
olpc_battery: Add support for CURRENT_NOW and VOLTAGE_NOW
olpc_battery: Add support for CHARGE_NOW
olpc_battery: Add support for CHARGE_FULL_DESIGN
olpc_battery: Ambient temperature is not available on XO-1.5
jz4740-battery: Should include linux/io.h
s3c_adc_battery: Add gpio_inverted field to pdata
power_supply: Don't use flush_scheduled_work()
power_supply: Fix use after free and memory leak
gpio-charger: Fix potential race between irq handler and probe/remove
gpio-charger: Provide default name for the power_supply
gpio-charger: Check result of kzalloc
jz4740-battery: Check if platform_data is supplied
isp1704_charger: Detect charger after probe
isp1704_charger: Set isp->dev before anything needs it
isp1704_charger: Detect HUB/Host chargers
isp1704_charger: Correct length for storing model
power_supply: Add gpio charger driver
jz4740-battery: Protect against concurrent battery readings
...
|
|
The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.
This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
Linus Torvalds
Clifton Barnes
Haojian Zhuang
Marek Vasut
Paul Parsons
John Stultz
Pali Rohár
Jiri Kosina
Anton Vorontsov
Kalle Jokiniemi
Benson Leung
MyungJoo Ham
Justin P. Mattock
Thomas Gleixner
Andres Salomon
Rhyland Klein
Vasily Khoruzhick
Heiko Stuebner
Axel Lin
Heikki Krogerus
Grazvydas Ignotas
Lars-Peter Clausen