| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This fixes a small issue in clps711x_get_duty() en passant: the
multiplication v * 0xf might have overflown.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362eab6 ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The array atmel_tcb_divisors is not supposed to be used outside of the
driver, so make it static.
This fixes a sparse warning:
drivers/pwm/pwm-atmel-tcb.c:64:10: warning: symbol 'atmel_tcb_divisors' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c0934e ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add Sunplus SoC SP7021 PWM Driver
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly
found on Xilinx FPGAs. At the moment clock control is very basic: we
just enable the clock during probe and pin the frequency. In the future,
someone could add support for disabling the clock when not in use.
Some common code has been specially demarcated. While currently only
used by the PWM driver, it is anticipated that it may be split off in
the future to be used by the timer driver as well.
This driver was written with reference to Xilinx DS764 for v1.03.a [1].
[1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Per-channel data is tracked using struct pwm_device::chip_data and
struct atmel_tcb_pwm_chip::pwms[]. Simplify by using the latter
consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This fixes a problem that was supposed to be addressed by commit
6eefb79d6f5bc ("pwm: sun4i: Remove erroneous else branch") - backlight
could not be switched off on some Allwinner A20. The commit was
correct, but was not a reliable fix for the problem, which was timing
related.
The real problem for the backlight switching problem was that sleeping
for a full period did not work, because delay_us is always zero.
It is zero because the period (plus 1 microsecond) is rounded down to
the next "jiffies", but the period is less than one jiffy.
On my Cubieboard 2, the period is 5ms, and 1 jiffy (at the default
HZ=100) is 10ms, so nsecs_to_jiffies(10ms+1us)=0.
The roundtrip from nanoseconds to jiffies and back to microseconds is
an unnecessary loss of precision; always rounding down (via
nsecs_to_jiffies()) then causes the breakage.
This patch eliminates this roundtrip, and directly converts from
nanoseconds to microseconds (for usleep_range()), using
DIV_ROUND_UP_ULL() to force rounding up. This way, the sleep time is
never zero, and after the sleep, we are guaranteed to be in a
different period, and the device is ready for another control command
for sure.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Basically this code did "jiffies + period - jiffies", and we can
simply eliminate the "jiffies" time stamp here.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Its value is calculated in sun4i_pwm_apply() and is used only there.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
- Remove the superfluous cast; the multiplication will yield a 64-bit
result due to the "100ULL" anyway,
- "a * (1 << b)" == "a << b".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
As a cherry-on-top cleanup, make error messages clearer to read
by changing instances of "clock: XXXX failed" to a more readable
"Failed to get XXXX clock". Also add "of" to unsupported period
error.
This is purely a cosmetic change; no "real" functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Switch from devm_kcalloc to devm_kmalloc_array when allocating clk_pwms,
as this structure is being filled right after allocating it, hence
there is no need to zero it out beforehand.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use dev_err_probe() to simplify handling errors in pwm_mediatek_probe().
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The lock only protects against concurrent users of the PWM API. This is not
expected to be necessary. And if there was such an issue, this is better
handled in the PWM core instead as it affects all drivers in the same way.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The X1000 has the same TCU / PWM hardware as other Ingenic SoCs,
but it has only 5 channels.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Status quo is that variables of type struct vt8500_chip * are named
"vt8500", "chip". Because usually only struct pwm_device * variables
are named "pwm" and "chip" is usually used for variabled of type
struct pwm_chip *.
So consistently use the same and non-conflicting name "vt8500".
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
During the driver probe, registers are not set to their POR value.
Signed-off-by: Lionel Vitte <lionel.vitte@free.fr>
Acked-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The variable timeout is being initialized with a value that is never
read, it is being re-assigned the same value later on. Remove the
redundant initialization and keep the latter assignment because it's
closer to the use of the variable.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since commit f9a8ee8c8bcd ("pwm: Always allocate PWM chip base ID
dynamically") there is no effect any more for assigning this variable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
The conversion wasn't quite straight forward because .config() and
.enable() were special to effectively swap their usual order. This resulted
in calculating the required values twice in some cases when
pwm_apply_state() was called. This is optimized en passant, and the order
of the callbacks is preserved without special jumping through hoops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
In all code locations but the probe function variables of type struct
stmpe_pwm * are called "stmpe_pwm". Align the name used in
stmpe_pwm_probe() accordingly. Still more as the current name "pwm" is
usually reserved for variables of type struct pwm_device *.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The driver never uses dev_get_drvdata() to retrieve the pwm driver data.
So drop setting it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Status quo is that variables of type struct sun4i_pwm_chip * are named
"pwm". This name is usually reserved for variabled of type struct
pwm_chip *.
So consistently use the same and non-conflicting name "sun4ichip" which
better reflects the intend
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Status quo is that variables of type struct tegra_pwm_chip * are named
"pwm", "chip" or "pc". The two formers are all not optimal because
usually only struct pwm_device * variables are named "pwm" and "chip" is
usually used for variabled of type struct pwm_chip *.
So consistently use the same and non-conflicting name "pc".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Status quo is that variables of type struct img_pwm_chip * are named
"pwm_chip", "pwm" or "chip" which are all not optimal because there is a
struct pwm_chip in the core, usually only struct pwm_device * variables are
named "pwm" and "chip" is usually used for variabled of type struct
pwm_chip *.
So consistently use the same and non-conflicting name "imgchip".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
As a side effect this improves the behaviour for big duty cycles where
max * duty_ns overflowed before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The per-channel data is available directly in the driver data struct. So
use it without making use of pwm_[gs]et_chip_data().
The relevant change introduced by this patch to lpc18xx_pwm_disable() at
the assembler level (for an arm lpc18xx_defconfig build) is:
push {r3, r4, r5, lr}
mov r4, r0
mov r0, r1
mov r5, r1
bl 0 <pwm_get_chip_data>
ldr r3, [r0, #0]
changes to
ldr r3, [r1, #8]
push {r4, lr}
add.w r3, r0, r3, lsl #2
ldr r3, [r3, #92] ; 0x5c
So this reduces stack usage, has an improved runtime behavior because of
better pipeline usage, doesn't branch to an external function and the
generated code is a bit smaller occupying less memory.
The codesize of lpc18xx_pwm_probe() is reduced by 32 bytes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Each devm allocations has an overhead of 24 bytes to store the related
struct devres_node additionally to the fragmentation of the allocator.
So allocating 16 struct lpc18xx_pwm_data (which only hold a single int)
adds quite some overhead. Instead put the per-channel data into the
driver data struct and allocate it in one go.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
When a driver calls pwmchip_add() it has to be prepared to immediately
get its callbacks called. So move allocation of driver data and hardware
initialization before the call to pwmchip_add().
This fixes a potential NULL pointer exception and a race condition on
register writes.
Fixes: 841e6f90bb78 ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM core only calls the apply callback with a valid state pointer,
so don't repeat this check already done in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The driver tracks per-channel data via struct pwm_device::chip_data and
struct meson_pwm::channels[]. The latter holds the actual data, the former
is only a pointer to the latter. So simplify by using struct
meson_pwm::channels[] consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
In meson_pwm_free() the function pwm_get_chip_data() always returns a
non-NULL pointer because it's only called when the request callback
succeeded and this callback calls pwm_set_chip_data() in this case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
In .request() pwm_get_chip_data() returns NULL always since commit
e926b12c611c ("pwm: Clear chip_data in pwm_put()"). (And if it didn't
returning 0 would be wrong because then .request() wouldn't reenable
the clk which the other driver code depends on.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Pull pwm updates from Thierry Reding:
"This contains a number of nice cleanups and improvements for the core
and various drivers, as well as a minor tweak to the json-schema
device tree bindings"
* tag 'pwm/for-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
dt-bindings: pwm: Avoid selecting schema on node name match
pwm: img: Use only a single idiom to get a runtime PM reference
pwm: vt8500: Implement .apply() callback
pwm: img: Implement .apply() callback
pwm: twl: Implement .apply() callback
pwm: Restore initial state if a legacy callback fails
pwm: Prevent a glitch for legacy drivers
pwm: Move legacy driver handling into a dedicated function
|
|
Pull drm updates from Dave Airlie:
"Highlights are support for privacy screens found in new laptops, a
bunch of nomodeset refactoring, and i915 enables ADL-P systems by
default, while starting to add RPL-S support.
vmwgfx adds GEM and support for OpenGL 4.3 features in userspace.
Lots of internal refactorings around dma reservations, and lots of
driver refactoring as well.
Summary:
core:
- add privacy screen support
- move nomodeset option into drm subsystem
- clean up nomodeset handling in drivers
- make drm_irq.c legacy
- fix stack_depot name conflicts
- remove DMA_BUF_SET_NAME ioctl restrictions
- sysfs: send hotplug event
- replace several DRM_* logging macros with drm_*
- move hashtable to legacy code
- add error return from gem_create_object
- cma-helper: improve interfaces, drop CONFIG_DRM_KMS_CMA_HELPER
- kernel.h related include cleanups
- support XRGB2101010 source buffers
ttm:
- don't include drm hashtable
- stop pruning fences after wait
- documentation updates
dma-buf:
- add dma_resv selftest
- add debugfs helpers
- remove dma_resv_get_excl_unlocked
- documentation
- make fences mandatory in dma_resv_add_excl_fence
dp:
- add link training delay helpers
gem:
- link shmem/cma helpers into separate modules
- use dma_resv iteratior
- import dma-buf namespace into gem helper modules
scheduler:
- fence grab fix
- lockdep fixes
bridge:
- switch to managed MIPI DSI helpers
- register and attach during probe fixes
- convert to YAML in several places.
panel:
- add bunch of new panesl
simpledrm:
- support FB_DAMAGE_CLIPS
- support virtual screen sizes
- add Apple M1 support
amdgpu:
- enable seamless boot for DCN 3.01
- runtime PM fixes
- use drm_kms_helper_connector_hotplug_event
- get all fences at once
- use generic drm fb helpers
- PSR/DPCD/LTTPR/DSC/PM/RAS/OLED/SRIOV fixes
- add smart trace buffer (STB) for supported GPUs
- display debugfs entries
- new SMU debug option
- Documentation update
amdkfd:
- IP discovery enumeration refactor
- interface between driver fixes
- SVM fixes
- kfd uapi header to define some sysfs bitfields.
i915:
- support VESA panel backlights
- enable ADL-P by default
- add eDP privacy screen support
- add Raptor Lake S (RPL-S) support
- DG2 page table support
- lots of GuC/HuC fw refactoring
- refactored i915->gt interfaces
- CD clock squashing support
- enable 10-bit gamma support
- update ADL-P DMC fw to v2.14
- enable runtime PM autosuspend by default
- ADL-P DSI support
- per-lane DP drive settings for ICL+
- add support for pipe C/D DMC firmware
- Atomic gamma LUT updates
- remove CCS FB stride restrictions on ADL-P
- VRR platform support for display 11
- add support for display audio codec keepalive
- lots of display refactoring
- fix runtime PM handling during PXP suspend
- improved eviction performance with async TTM moves
- async VMA unbinding improvements
- VMA locking refactoring
- improved error capture robustness
- use per device iommu checks
- drop bits stealing from i915_sw_fence function ptr
- remove dma_resv_prune
- add IC cache invalidation on DG2
nouveau:
- crc fixes
- validate LUTs in atomic check
- set HDMI AVI RGB quant to full
tegra:
- buffer objects reworks for dma-buf compat
- NVDEC driver uAPI support
- power management improvements
etnaviv:
- IOMMU enabled system support
- fix > 4GB command buffer mapping
- close a DoS vector
- fix spurious GPU resets
ast:
- fix i2c initialization
rcar-du:
- DSI output support
exynos:
- replace legacy gpio interface
- implement generic GEM object mmap
msm:
- dpu plane state cleanup in prep for multirect
- dpu debugfs cleanups
- dp support for sc7280
- a506 support
- removal of struct_mutex
- remove old eDP sub-driver
anx7625:
- support MIPI DSI input
- support HDMI audio
- fix reading EDID
lvds:
- fix bridge DT bindings
megachips:
- probe both bridges before registering
dw-hdmi:
- allow interlace on bridge
ps8640:
- enable runtime PM
- support aux-bus
tx358768:
- enable reference clock
- add pulse mode support
ti-sn65dsi86:
- use regmap bulk write
- add PWM support
etnaviv:
- get all fences at once
gma500:
- gem object cleanups
kmb:
- enable fb console
radeon:
- use dma_resv_wait_timeout
rockchip:
- add DSP hold timeout
- suspend/resume fixes
- PLL clock fixes
- implement mmap in GEM object functions
- use generic fbdev emulation
sun4i:
- use CMA helpers without vmap support
vc4:
- fix HDMI-CEC hang with display is off
- power on HDMI controller while disabling
- support 4K@60Hz modes
- support 10-bit YUV 4:2:0 output
vmwgfx:
- fix leak on probe errors
- fail probing on broken hosts
- new placement for MOB page tables
- hide internal BOs from userspace
- implement GEM support
- implement GL 4.3 support
virtio:
- overflow fixes
xen:
- implement mmap as GEM object function
omapdrm:
- fix scatterlist export
- support virtual planes
mediatek:
- MT8192 support
- CMDQ refinement"
* tag 'drm-next-2022-01-07' of git://anongit.freedesktop.org/drm/drm: (1241 commits)
drm/amdgpu: no DC support for headless chips
drm/amd/display: fix dereference before NULL check
drm/amdgpu: always reset the asic in suspend (v2)
drm/amdgpu: put SMU into proper state on runpm suspending for BOCO capable platform
drm/amd/display: Fix the uninitialized variable in enable_stream_features()
drm/amdgpu: fix runpm documentation
amdgpu/pm: Make sysfs pm attributes as read-only for VFs
drm/amdgpu: save error count in RAS poison handler
drm/amdgpu: drop redundant semicolon
drm/amd/display: get and restore link res map
drm/amd/display: support dynamic HPO DP link encoder allocation
drm/amd/display: access hpo dp link encoder only through link resource
drm/amd/display: populate link res in both detection and validation
drm/amd/display: define link res and make it accessible to all link interfaces
drm/amd/display: 3.2.167
drm/amd/display: [FW Promotion] Release 0.0.98
drm/amd/display: Undo ODM combine
drm/amd/display: Add reg defs for DCN303
drm/amd/display: Changed pipe split policy to allow for multi-display pipe split
drm/amd/display: Set optimize_pwr_state for DCN31
...
|
|
The PWM on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now PWM must be resumed using
runtime PM API in order to initialize the PWM power state. The PWM clock
rate must be changed using OPP API that will reconfigure the power domain
performance state in accordance to the rate. Add runtime PM and OPP
support to the PWM driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Backmerging from drm/drm-next for v5.16-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Currently there are two very similar approaches in use by this driver:
img_pwm_config() uses pm_runtime_get_sync() and calls
pm_runtime_put_autosuspend() in the error path; img_pwm_enable() calls
pm_runtime_resume_and_get() which already puts the reference in its own
error path.
Align pm_runtime usage and use the same idiom in both locations.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply(). This just pushes down a slightly
optimized variant of how legacy drivers are handled in the core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
It is not entirely accurate to go back to the initial state after e.g.
.enable() failed, as .config() still modified the hardware, but this same
inconsistency exists for drivers that implement .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
If a running PWM is reconfigured to disabled calling the ->config()
callback before disabling the hardware might result in a glitch where
the (maybe) new period and duty_cycle are visible on the output before
disabling the hardware.
So handle disabling before calling ->config(). Also exit early in this case
which is possible because period and duty_cycle don't matter for disabled PWMs.
In return however ->config has to be called even if state->period ==
pwm->state.period && state->duty_cycle != pwm->state.duty_cycle because setting
these might have been skipped in the previous call.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
There is no change in behaviour, only some code is moved from
pwm_apply_state to a separate function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The pwm_ prefix suggests that pwm_busy_wait() is a function provided by
the pwm core. Use the otherwise consistently used driver prefix for this
function, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
Uwe Kleine-König
Hammer Hsieh
Sean Anderson
Max Kellermann
Geert Uytterhoeven
AngeloGioacchino Del Regno
Aidan MacDonald
zhaoxiao
Lionel Vitte
Colin Ian King
Linus Torvalds
Dmitry Osipenko
Thomas Zimmermann