Age | Commit message (Collapse) | Author | Files | Lines |
|
Marek reported that he saw an issue with the below snippet in that
timing measurements where off when loaded as unpriv while results
were reasonable when loaded as privileged:
[...]
uint64_t a = bpf_ktime_get_ns();
uint64_t b = bpf_ktime_get_ns();
uint64_t delta = b - a;
if ((int64_t)delta > 0) {
[...]
Turns out there is a bug where a corner case is missing in the fix
d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar
type from different paths"), namely fixup_bpf_calls() only checks
whether aux has a non-zero alu_state, but it also needs to test for
the case of BPF_ALU_NON_POINTER since in both occasions we need to
skip the masking rewrite (as there is nothing to mask).
Fixes: d3bd7413e0ca ("bpf: fix sanitation of alu op with pointer / scalar type from different paths")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Reported-by: Arthur Fabre <afabre@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/netdev/CAJPywTJqP34cK20iLM5YmUMz9KXQOdu1-+BZrGMAGgLuBWz7fg@mail.gmail.com/T/
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3fe ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MIPS eBPF JIT calls flush_icache_range() in order to ensure the
icache observes the code that we just wrote. Unfortunately it gets the
end address calculation wrong due to some bad pointer arithmetic.
The struct jit_ctx target field is of type pointer to u32, and as such
adding one to it will increment the address being pointed to by 4 bytes.
Therefore in order to find the address of the end of the code we simply
need to add the number of 4 byte instructions emitted, but we mistakenly
add the number of instructions multiplied by 4. This results in the call
to flush_icache_range() operating on a memory region 4x larger than
intended, which is always wasteful and can cause crashes if we overrun
into an unmapped page.
Fix this by correcting the pointer arithmetic to remove the bogus
multiplication, and use braces to remove the need for a set of brackets
whilst also making it obvious that the target field is a pointer.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4e8 ("MIPS: Add missing file for eBPF JIT.")
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.
This patch sets a tx hw traffic mode with 8 queues.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651
Fixes: 71a963cfc50b ("net: aquantia: increase max number of hw queues")
Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.
Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.
In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
__func__, asoc, max_data);
~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
printk(fmt, ##__VA_ARGS__); \
~~~ ^
Fixes: 5b5e0928f742 ("lib/vsprintf.c: remove %Z support")
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Matthias Maennich <maennich@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS: 0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094] <IRQ>
[10258690.372094] skb_to_sgvec+0x11/0x40
[10258690.372094] start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094] dev_hard_start_xmit+0x9b/0x200
[10258690.372094] sch_direct_xmit+0xff/0x260
[10258690.372094] __qdisc_run+0x15e/0x4e0
[10258690.372094] net_tx_action+0x137/0x210
[10258690.372094] __do_softirq+0xd6/0x2a9
[10258690.372094] irq_exit+0xde/0xf0
[10258690.372094] smp_apic_timer_interrupt+0x74/0x140
[10258690.372094] apic_timer_interrupt+0xf/0x20
[10258690.372094] </IRQ>
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: Sheng Lan <lansheng@huawei.com>
Reported-by: Qin Ji <jiqin.ji@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com>
Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f982f95 ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.
Fixes: 5fa12739a53d0 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a couple of new tests, explicitly checking that the kernel
timely releases PMTU exceptions on related device removal.
This is mostly a regression test vs the issue fixed by
commit f5b51fe804ec ("ipv6: route: purge exception on removal")
Only 2 new test cases have been added, instead of extending all
the existing ones, because the reproducer requires executing
several commands and would slow down too much the tests otherwise.
v2 -> v3:
- more cleanup, still from Stefano
v1 -> v2:
- several script cleanups, as suggested by Stefano
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise, the configured IPv6 address could be still "tentative"
at test time, possibly causing tests failures.
We can also drop some sleep along the code and decrease the
timeout for most commands so that the test runtime decreases.
v1 -> v2:
- fix comment (Stefano)
Fixes: d1f1b9cbf34c ("selftests: net: Introduce first PMTU test")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KASAN report this:
BUG: KASAN: null-ptr-deref in nfc_llcp_build_gb+0x37f/0x540 [nfc]
Read of size 3 at addr 0000000000000000 by task syz-executor.0/5401
CPU: 0 PID: 5401 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
kasan_report+0x171/0x18d mm/kasan/report.c:321
memcpy+0x1f/0x50 mm/kasan/common.c:130
nfc_llcp_build_gb+0x37f/0x540 [nfc]
nfc_llcp_register_device+0x6eb/0xb50 [nfc]
nfc_register_device+0x50/0x1d0 [nfc]
nfcsim_device_new+0x394/0x67d [nfcsim]
? 0xffffffffc1080000
nfcsim_init+0x6b/0x1000 [nfcsim]
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f9cb79dcc58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003
RBP: 00007f9cb79dcc70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9cb79dd6bc
R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004
nfc_llcp_build_tlv will return NULL on fails, caller should check it,
otherwise will trigger a NULL dereference.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: eda21f16a5ed ("NFC: Set MIU and RW values from CONNECT and CC LLCP frames")
Fixes: d646960f7986 ("NFC: Initial LLCP support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Incoming packets may have IP header checksum verified by the host.
They may not have IP header checksum computed after coalescing.
This patch re-compute the checksum when necessary, otherwise the
packets may be dropped, because Linux network stack always checks it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MPLS does not support nexthops with an MPLS address family.
Specifically, it does not handle RTA_GATEWAY attribute. Make it
clear by returning an error.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 currently does not support nexthops outside of the AF_INET6 family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
$ ip ro ls
...
2001:db8:2::/64 dev eth0 metric 1024 pref medium
Catch this and fail the route add:
$ ip -6 ro add 2001:db8:2::/64 via inet 172.16.1.1 dev eth0
Error: IPv6 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv4 currently does not support nexthops outside of the AF_INET family.
Specifically, it does not handle RTA_VIA attribute. If it is passed
in a route add request, the actual route added only uses the device
which is clearly not what the user intended:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 dev eth0
Catch this and fail the route add:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8:1::1 dev eth0
Error: IPv4 does not support RTA_VIA attribute.
Fixes: 03c0566542f4c ("mpls: Netlink commands to add, remove, and dump routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID")
Signed-off-by: Peng Sun <sironhide0null@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace set_current_state with __set_current_state since no memory
barrier is needed at this point.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9060cb719e61 ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
- base_sock_release
- bnep_sock_release
- cmtp_sock_release
- data_sock_release
- dn_release
- hci_sock_release
- hidp_sock_release
- iucv_sock_release
- l2cap_sock_release
- llcp_sock_release
- llc_ui_release
- rawsock_release
- rfcomm_sock_release
- sco_sock_release
- svc_release
- vcc_release
- x25_release
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
#include <pthread.h>
#include <stdlib.h>
#include <sys/socket.h>
#include <unistd.h>
pthread_t t;
volatile int fd;
void *close_thread(void *arg)
{
for (;;) {
usleep(rand() % 100);
close(fd);
}
}
int main()
{
pthread_create(&t, NULL, close_thread, NULL);
for (;;) {
fd = socket(rand() % 50, rand() % 11, 0);
fchownat(fd, "", 1000, 1000, 0x1000);
close(fd);
}
}
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac5b ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda9089 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 4e8ddd7f1758 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f1758 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a WARN_ON(!tcp_skb_pcount(skb))
in tcp_send_loss_probe() [1]
This was caused by TCP_REPAIR sent skbs that inadvertenly
were missing a call to tcp_init_tso_segs()
[1]
WARNING: CPU: 1 PID: 0 at net/ipv4/tcp_output.c:2534 tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.0.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
panic+0x2cb/0x65c kernel/panic.c:214
__warn.cold+0x20/0x45 kernel/panic.c:571
report_bug+0x263/0x2b0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
fixup_bug arch/x86/kernel/traps.c:173 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Code: 88 fc ff ff 4c 89 ef e8 ed 75 c8 fb e9 c8 fc ff ff e8 43 76 c8 fb e9 63 fd ff ff e8 d9 75 c8 fb e9 94 f9 ff ff e8 bf 03 91 fb <0f> 0b e9 7d fa ff ff e8 b3 03 91 fb 0f b6 1d 37 43 7a 03 31 ff 89
RSP: 0018:ffff8880ae907c60 EFLAGS: 00010206
RAX: ffff8880a989c340 RBX: 0000000000000000 RCX: ffffffff85dedbdb
RDX: 0000000000000100 RSI: ffffffff85dee0b1 RDI: 0000000000000005
RBP: ffff8880ae907c90 R08: ffff8880a989c340 R09: ffffed10147d1ae1
R10: ffffed10147d1ae0 R11: ffff8880a3e8d703 R12: ffff888091b90040
R13: ffff8880a3e8d540 R14: 0000000000008000 R15: ffff888091b90860
tcp_write_timer_handler+0x5c0/0x8a0 net/ipv4/tcp_timer.c:583
tcp_write_timer+0x10e/0x1d0 net/ipv4/tcp_timer.c:607
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
</IRQ>
RIP: 0010:native_safe_halt+0x2/0x10 arch/x86/include/asm/irqflags.h:58
Code: ff ff ff 48 89 c7 48 89 45 d8 e8 59 0c a1 fa 48 8b 45 d8 e9 ce fe ff ff 48 89 df e8 48 0c a1 fa eb 82 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90
RSP: 0018:ffff8880a98afd78 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff1125061 RBX: ffff8880a989c340 RCX: 0000000000000000
RDX: dffffc0000000000 RSI: 0000000000000001 RDI: ffff8880a989cbbc
RBP: ffff8880a98afda8 R08: ffff8880a989c340 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffffffff889282f8 R14: 0000000000000001 R15: 0000000000000000
arch_cpu_idle+0x10/0x20 arch/x86/kernel/process.c:555
default_idle_call+0x36/0x90 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x386/0x570 kernel/sched/idle.c:262
cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:353
start_secondary+0x404/0x5c0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes: 79861919b889 ("tcp: fix TCP_REPAIR xmit queue setup")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
[1]
watchdog: BUG: soft lockup - CPU#0 stuck for 123s! [syz-executor.2:10492]
Modules linked in:
irq event stamp: 27515
hardirqs last enabled at (27514): [<ffffffff81006673>] trace_hardirqs_on_thunk+0x1a/0x1c
hardirqs last disabled at (27515): [<ffffffff8100668f>] trace_hardirqs_off_thunk+0x1a/0x1c
softirqs last enabled at (32): [<ffffffff8632ee73>] x25_get_neigh+0xa3/0xd0 net/x25/x25_link.c:336
softirqs last disabled at (34): [<ffffffff86324bc3>] x25_find_socket+0x23/0x140 net/x25/af_x25.c:341
CPU: 0 PID: 10492 Comm: syz-executor.2 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x50 kernel/kcov.c:97
Code: f4 ff ff ff e8 11 9f ea ff 48 c7 05 12 fb e5 08 00 00 00 00 e9 c8 e9 ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 <48> 8b 75 08 65 48 8b 04 25 40 ee 01 00 65 8b 15 38 0c 92 7e 81 e2
RSP: 0018:ffff88806e94fc48 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffff1100d84dac5 RBX: 0000000000000001 RCX: ffffc90006197000
RDX: 0000000000040000 RSI: ffffffff86324bf3 RDI: ffff88806c26d628
RBP: ffff88806e94fc48 R08: ffff88806c1c6500 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: ffff88806c26d628
R13: ffff888090455200 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007f3a107e4700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3a107e3db8 CR3: 00000000a5544000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__x25_find_socket net/x25/af_x25.c:327 [inline]
x25_find_socket+0x7d/0x140 net/x25/af_x25.c:342
x25_new_lci net/x25/af_x25.c:355 [inline]
x25_connect+0x380/0xde0 net/x25/af_x25.c:784
__sys_connect+0x266/0x330 net/socket.c:1662
__do_sys_connect net/socket.c:1673 [inline]
__se_sys_connect net/socket.c:1670 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1670
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f3a107e3c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e29
RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000005
RBP: 000000000073c040 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f3a107e46d4
R13: 00000000004be362 R14: 00000000004ceb98 R15: 00000000ffffffff
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 10493 Comm: syz-executor.3 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline]
RIP: 0010:queued_write_lock_slowpath+0x143/0x290 kernel/locking/qrwlock.c:86
Code: 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 41 0f b6 55 00 <41> 38 d7 7c eb 84 d2 74 e7 48 89 df e8 cc aa 4e 00 eb dd be 04 00
RSP: 0018:ffff888085c47bd8 EFLAGS: 00000206
RAX: 0000000000000300 RBX: ffffffff89412b00 RCX: 1ffffffff1282560
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89412b00
RBP: ffff888085c47c70 R08: 1ffffffff1282560 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: 00000000000000ff
R13: fffffbfff1282560 R14: 1ffff11010b88f7d R15: 0000000000000003
FS: 00007fdd04086700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdd04064db8 CR3: 0000000090be0000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
queued_write_lock include/asm-generic/qrwlock.h:104 [inline]
do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203
__raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline]
_raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312
x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267
x25_bind+0x273/0x340 net/x25/af_x25.c:703
__sys_bind+0x23f/0x290 net/socket.c:1481
__do_sys_bind net/socket.c:1492 [inline]
__se_sys_bind net/socket.c:1490 [inline]
__x64_sys_bind+0x73/0xb0 net/socket.c:1490
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Fixes: 90c27297a9bf ("X.25 remove bkl in bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This callback was removed some time ago, also remove the documentation.
Fixes: 1b6dd556c304 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|