aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/regulator
AgeCommit message (Collapse)AuthorFilesLines
2012-06-19regulator: s5m8767a: Support AP watchdog reset operationSangbeom Kim1-42/+91
The S5M8767A can't know status of ap reset. So, After AP watchdog reset, AP can't boot normally. Problem can be happened like below condition. - AP Bootable lowest voltage(vdd_arm): 0.9v - AP DVFS voltage table: 0.8v, 0.9v, 1.0v - During AP works on lowest voltage(0.8V), watchdog reset is asserted - AP can't boot, because vdd arm is still 0.8v Solution - Basic concept: After ap watchdog reset, GPIO configuration is changed by default value - S5M8767A has function of voltage control with gpio (8 levels with 3 gpios) - Set bootable voltage on level 0 -> can work with default gpio configuration - In the probing, Change voltage control level from level 0 to level 1 - Execute normal dvfs operation on level 1 - After watchdog reset, ap gpio is set by default value - PMIC operation mode is changed by ap reset (level1 -> level0) - Regardless of previous vdd_arm voltage, AP always can be booted. Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19regulator: max77686: Convert driver to use regulator_set_voltage_time_sel.Yadwinder Singh Brar1-33/+9
This patch converts the driver to use regulator_set_voltage_time_sel() as .set_voltage_time_sel() callback. It also sets ramp_delay as 100000 uV/us for LDOs & normal BUCKs and 27500 uV/us(default/reset value) for BUCKs[2/3/4] in regulator_desc[]. Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19regulator: tps65023: Convert to get_voltage_selAxel Lin1-7/+7
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19regulator: tps65023: Convert to regulator_list_voltage_tableAxel Lin1-104/+49
In current mapping table settings, min_uV/max_uV are always equal to volt_table[0] and volt_table[table_len -1]. Thus remove min_uV and max_uV from struct tps_info. The table based mapping with table_len == 1 means fixed voltage. So we don't need fixed flag to differentiate if it is fixed or not. This patch adds DCDC_FIXED_3300000_VSEL_table and DCDC_FIXED_1800000_VSEL_table for fixed voltage cases. So we can convert tps65023_dcdc_ops to regulator_list_voltage_table. This makes the code simpler. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19regulator: mc13xxx: Remove mc13xxx_sw_regulator_is_enabled functionAxel Lin3-8/+0
If .is_enabled callback is not implemented, regulator core assumes that the regulator is always on. Thus we don't need mc13xxx_sw_regulator_is_enabled function. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: twl: Remove references to 32kHz clock from DT bindingsMark Brown1-2/+0
Due to the lack of a generic clock API we'd had the 32kHz clock in the regulator driver but this is definitely a Linux-specific thing and now we have a clock API hopefully the code can be moved elsewhere. Try to avoid getting DTs deployed relying on the 32kHz clock by removing it from the bindings, grep seems to tell me it's not currently used anyway. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: Fix double free in devm_regulator_put()Mark Brown1-3/+1
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: tps65910: Don't use 0 as NULLMark Brown1-1/+1
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: core: Change the unit of ramp_delay from mV/uS to uV/uSAxel Lin1-2/+2
This change makes it possible to set ramp_delay with 0.xxx mV/uS without truncation issue. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: core: Support table based mapping in regulator_set_voltage_time_selAxel Lin1-12/+25
For table based mapping, we can calculate voltage difference by below equation: abs(rdev->desc->volt_table[new_selector] - rdev->desc->volt_table[old_selector]) Thus we can make regulator_set_voltage_time_sel work for table based mapping. regulator_set_voltage_time_sel() only supports linear or table based mapping. In case it is misused, also warn if neither linear nor table based mapping is used with regulator_set_voltage_time_sel(). Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18regulator: Fix setting constraints->ramp_delay in of_get_regulation_constraintsAxel Lin1-1/+1
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: Add ramp_delay configuration to constraintsYadwinder Singh Brar2-5/+24
For some hardwares ramp_delay for BUCKs is a configurable parameter which can be configured through DT or board file.This patch adds ramp_delay to regulator constraints and allow user to configure it for regulators which supports this feature, through DT or board file. It will provide two ways of setting the ramp_delay for a regulator: First, by setting it as constraints in board file(for configurable regulators) and set_machine_constraints() will take care of setting it on hardware by calling(the provided) .set_ramp_delay() operation(callback). Second, by setting it as data in regulator_desc(as fixed/default ramp_delay rate) for a regulator in driver. regulator_set_voltage_time_sel() will give preference to constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly users should also take care accordingly while refering ramp_delay rate(in case of implementing their private .set_voltage_time_sel() callbacks for different regulators). [Rewrote subject for 80 columns -- broonie] Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm831x-dcdc: Convert wm831x_buckv_ops to set_voltage_sel and map_voltageAxel Lin1-13/+8
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm831x-dcdc: Convert wm831x_buckp_ops to regulator_set_voltage_sel_regmapAxel Lin1-35/+9
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm831x-ldo: Convert to regulator_set_voltage_sel_regmap and map_voltageAxel Lin1-91/+38
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: ab3100: Convert fixed voltage to use regulator_list_voltage_linearAxel Lin1-11/+13
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: pcf50633: Convert to regulator_set_voltage_sel_regmap and map_voltageAxel Lin1-14/+6
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: ab8500: Remove min_uV and max_uV from struct ab8500_regulator_infoAxel Lin1-12/+0
The min_uV and max_uV are not really used in the code and misleading because the min_uV and max_uV settings does not match the value in the voltage table. For example, we have static const unsigned int ldo_vaux3_voltages[] = { 1200000, 1500000, 1800000, 2100000, 2500000, 2750000, 2790000, 2910000, }; With below min_uV/max_uV settings for AB8500_LDO_AUX3. .min_uV = 1100000, .max_uV = 3300000, The min_uV/max_uV for AB8500_LDO_AUX3 seems copy-paste from AB8500_LDO_AUX2 and is wrong. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: ab8500: Use regulator_list_voltage_linear for ab8500_regulator_fixed_opsAxel Lin1-32/+9
Also removes set_voltage_time_sel callback from ab8500_regulator_fixed_ops because the voltage won't change. ( And ab8500_regulator_fixed_ops does not implement get_voltage_sel so set_voltage_time_sel won't be called ) Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: mc13xxx: Convert to regulator_list_voltage_tableAxel Lin4-70/+49
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: mc13xxx: Fix voltage checking for mc13xxx_fixed_regulator_set_voltageAxel Lin1-2/+2
The voltage range checking should be to ensure mc13xxx_regulators[id].voltages[0] falls with min_uV and max_uV. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: tps62360: Simplify tps62360_set_voltage_time_sel implementationAxel Lin1-10/+3
For linear mappings, we can use below equation to get the voltage difference between new_selector and old_selector: abs(new_selector - old_selector) * rdev->desc->uV_step Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm831x-dcdc: Convert wm831x_buckp_ops to regulator_list_voltage_linearAxel Lin1-11/+4
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: tps65023: Fix mask for LDOs output voltage select controlAxel Lin1-1/+1
According to the datasheet: The LDO_CTRL registers are used to set the output voltage of LDO1 and LDO2. LDO_CTRL[7] and LDO_CTRL[3] are reserved and should always be written to 0. Thus the mask for TPS65023_LDO_1 and TPS65023_LDO_2 should be 0x07 and 0x70 respectively. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: tps65023: Set n_voltages to 1 for fixed voltageAxel Lin1-1/+4
For fixed voltage, the n_voltages should be 1 rather than 0. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm8350: Reuse map_voltage() to get selector of a given uVAxel Lin1-77/+50
Reuse map_voltage() to get the selector of a given uV. Then we can remove wm8350_ldo_mvolts_to_val() and wm8350_dcdc_mvolts_to_val(). Also remove unused wm8350_dcdc_val_to_mvolts() function. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: wm8350: Use wm8350_ldo_list_voltage instead of open code to verify selected voltageAxel Lin1-31/+21
Call wm8350_ldo_list_voltage() instead of open code to verify selected voltage falls within specified range. Use wm8350_ldo_list_voltage() here is less error prone. wm8350_ldo_val_to_mvolts() is only used in wm8350_ldo_list_voltage now, so remove it and move the implementation to wm8350_ldo_list_voltage(). This patch also include below small changes in wm8350_ldo_map_voltage: 1. wm8350_ldo_map_voltage() returns selector, thus rename variable mV to sel. 2. Use DIV_ROUND_UP macro to calculate selector. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: core.c Only delay when setting voltage requires thisPhilip Rakity1-7/+7
minor optimization: move delay code to where delay is set and thus where it is used vs in the main line path. Signed-off-by: Philip Rakity <prakity@marvell.com> Acked-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: core.c Pass voltage to notifier when setting voltagePhilip Rakity1-3/+3
The voltage being set should be passed to the call in handler requesting the callback. Currently this is not done. The calling handler cannot call regulator_get_voltage() to get the information since the mutex is held by the regulator and deadlock occurs. Without this change the receiver of the call in cannot know what action to take. This is used, for example, to set PAD voltages when doing SD vccq voltage changes. [Review and spelling fix in the commit log from Pankaj Jangra] Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: core: Actually use the data in _notifier_call_chain()Mark Brown1-1/+1
Reported-by: Pankaj Jangra <jangra.pankaj9@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: Change db8500-prcmu match names to reflect Device TreeLee Jones1-20/+20
The 'name' field in 'struct of_regulator_match' expects to match with its corresponding regulator device node in the Device Tree. This patch renames each of the regulators in the db8500-prcum regulator driver so this is true. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: Change ab8500 match names to reflect Device TreeLee Jones1-11/+11
The 'name' field in 'struct of_regulator_match' expects to match with its corresponding regulator device node in the Device Tree. This patch renames each of the regulators in the ab8500 regulator driver so this is true. Signed-off-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17regulator: Fix the s5m8767a problem of the division by nullSangbeom Kim1-1/+1
If ramp_delay is 0, delay value can be divided by zero. This patch can fix the problem. Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: tps65217: Convert to regulator_[is_enabled|get_voltage_sel]_regmapAxel Lin1-72/+42
This patch converts .is_enabled and .get_voltage_sel to regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap. For .enable, .disable, and .set_voltage_sel, the write protect level is either 1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap. Now we store the enable reg/mask and vsel reg/mask in regulator_desc, so we can remove enable_mask, set_vout_reg, and set_vout_mask from struct tps_info. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: wm8400: Adjust the equation for selector >= 15 in wm8400_ldo_list_voltageAxel Lin1-1/+1
Adjust the equation for selector >= 15 for better readability. The equation "1700000 + ((selector - 15) * 100000)" can be interpreted by: Starting from selector 15: Steps of 100mV from 1700mV Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: Replace set_voltage with set_voltage_selSangbeom Kim1-24/+14
To apply delay time for voltage change, replace s5m8767_set_voltage with s5m8767_set_voltage_sel. Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: wm8400: Use wm8400_ldo_list_voltage instead of open code to verify selected voltageAxel Lin1-15/+7
Call wm8400_ldo_list_voltage() instead of open code to verify selected voltage falls within specified range. Use wm8400_ldo_list_voltage() here is less error prone. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: Remove s5m8767a buck initializationSangbeom Kim1-3/+0
As s5m8767a is revisioned, remove unnecessary buck 2,3,4 initialization routine. Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-13regulator: wm8350: Add missing min_uV and uV_step settings for DCDC4Axel Lin1-0/+2
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: core: Return correct delay time in regulator_set_voltage_time_selAxel Lin1-1/+1
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV. The unit of ramp_delay is mV/us. Current code multiples 1000 at wrong place. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: max77686: Fix the delay time for set_voltage_time_selAxel Lin1-2/+2
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV. The unit of ramp_rate is mV/us. Thus 1000 should be multiplied. Signed-off-by: Axel Lin <axel.lin@gmail.com> Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: core: Add regulator_set_voltage_time_sel to calculate ramp delay.Yadwinder Singh Brar1-0/+24
This patch adds regulator_set_voltage_time_sel(), to move into core, the commonly used code by drivers to provide the .set_voltage_time_sel callback. It will also allow us to configure different ramp delay for different regulators easily. Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: max77686: Check pdata->num_regulators earlierAxel Lin1-23/+18
If this driver only works when pdata->num_regulators == MAX77686_REGULATORS, let's check it earlier. Also remove unused num_regulators from struct max77686_data. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: anatop: Convert to set_voltage_sel and regulator_map_voltage_linearAxel Lin1-23/+6
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: twl: Convert twl6030ldo_ops to use regulator_list_voltage_linearAxel Lin1-8/+5
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-11regulator: isl6271a: Remove setting map_voltage callback for isl_fixed_opsAxel Lin1-1/+0
isl_fixed_ops does not implement set_voltage_sel callback, adding map_voltage here is misleading. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-08regulator: max1586: Convert max1586_v3_ops to set_voltage_sel and map_voltage_linearAxel Lin1-16/+6
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-08regulator: max1586: Convert max1586_v3_ops to regulator_list_voltage_linearAxel Lin1-21/+11
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-08regulator: tps6586x: Convert to regulator_list_voltage_tableAxel Lin1-36/+25
Also adds tps6586x_ldo0_voltages mapping table for LDO0, so we can remove the hack in tps6586x_list_voltage() and convert it to regulator_list_voltage_table. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-08regulator: pcap: Convert to regulator_list_voltage_tableAxel Lin1-53/+42
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.