| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit 7e64db1597fe114b83fe17d0ba96c6aa5fca419a.
The thin provisioning feature introduces an IOCTL and the discard support
to allow userspace tools and filesystems to release unused and previously
allocated space respectively.
During some internal performance improvements and further tests, the
release of allocated space revealed some issues that may lead to data
corruption in some configurations when filesystems are mounted with
discard support enabled.
While we're working on a fix and trying to clarify the situation,
this commit reverts the discard support for ESE volumes to prevent
potential data corruption.
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is possible that the CCW commands for reading volume and extent pool
information are not supported, either by the storage server (for
dedicated DASDs) or by z/VM (for virtual devices, such as MDISKs).
As a command reject will occur in such a case, the current error
handling leads to a failing online processing and thus the DASD can't be
used at all.
Since the data being read is not essential for an fully operational
DASD, the error handling can be removed. Information about the failing
command is sent to the s390dbf debug feature.
Fixes: c729696bcf8b ("s390/dasd: Recognise data for ESE volumes")
Cc: <stable@vger.kernel.org> # 5.3
Reported-by: Frank Heimes <frank.heimes@canonical.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The storage server issues three different types of out-of-space messages
whenever the Extent Pool or Extent Repository space runs short. When a
configured warning watermark is reached, the physical space is
completeley exhausted, or the capacity constraints have been relieved, a
message is received.
A log entry for the sysadmin to react to is generated in any case. In
case the physical space is completely exhausted, sense data that reads
"no space left on device" is received. In this case, currently running
I/O will be blocked until space has either been released or added to the
extent pool, and a relieve message was received via an attention
interrupt.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
ESE (Extent Space Efficient) volumes are thin-provisioned and therefore
space is only occupied with real data. In order to make previously used
space available for re-allocation again, discard support is enabled for
ESE volumes allowing the DASD driver to release said space.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
ECKD, FBA, and the DIAG discipline use slightly different block layer
settings. In preparation of even more diverse queue settings, make
dasd_setup_queue() a discipline function.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Userspace tools might have the need to release space for Extent Space
Efficient (ESE) volumes when working with such a device.
Provide the necessarry interface for such a task by implementing a new
ioctl BIODASDRAS. The ioctl uses the format_data_t data structure for
data input:
typedef struct format_data_t {
unsigned int start_unit; /* from track */
unsigned int stop_unit; /* to track */
unsigned int blksize; /* sectorsize */
unsigned int intensity;
} format_data_t;
If the intensity is set to 0x40, start_unit and stop_unit are ignored
and space for the entire volume is released. Otherwise, if intensity is
set to 0, the respective range is released (if possible).
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
A dynamic formatting is issued whenever a write request returns with
either a No Record Found error (Command Mode), Incorrect Length error
(Transport Mode), or File Protected error (Transport Mode). All three
cases mean that the tracks in question haven't been initialized in a
desired format yet.
The part of the volume that was tried to be written on is then formatted
and the original request is re-queued.
As the formatting will happen during normal I/O operations, it is quite
likely that there won't be any memory available to build the respective
request. Another two pages of memory are allocated per volume
specifically for the dynamic formatting.
The dasd_eckd_build_format() function is extended to make sure that the
original startdev is reused. Also, all formatting and format check
functions use the new memory pool exclusively now to reduce complexity.
Read operations will always return zero data when unformatted areas are
read.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
In order to work with Extent Space Efficient (ESE) volumes, certain
viable information about those volumes and the corresponding extent
pool (such as extent size, configured space, allocated space, etc.) can
be provided.
Use the CCW commands Volume Storage Query and Logical Configuration
Query to receive detailed information about ESE volumes and the extent
pool respectively. These information are made accessible via internal
functions for subsequent users, and via sysfs attributes for userpsace
usage.
The new sysfs attributes reside in separate directories called capacity
and extent_pool.
attributes:
ese:
0/1 depending on whether the volume is an ESE volume
Capacity related attributes:
space_allocated:
Space currently allocated by the volume (in cyl)
space_configured:
Remaining space in the extent pool (in cyl)
logical_capacity:
The entire addressable space for this volume (in cyl)
Extent Pool related attributes:
pool_id:
ID of the extent pool the volume in question resides in
pool_oos:
Extent pool is out-of-space
extent_size:
Size of a single extent in this pool
cap_at_warnlevel
Extent pool capacity at warn level
warn_threshold:
Threshold at which percentage of remaining extent pool space a
warning message is issued
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The disk layout and volume information of a DASD reside in the first two
tracks of cylinder 0. When a DASD is set online, currently the first
three tracks are read and analysed to confirm an expected layout.
For CDL (Compatible Disk Layout) only count area data of the first track
is evaluated and checked against expected key and data lengths. For LDL
(Linux Disk Layout) the first and third track is evaluated. However,
an LDL formatted volume is expected to be in the same format across all
tracks. Checking the third track therefore doesn't have any more value
than checking any other track at random.
Now, an Extent Space Efficient (ESE) DASD is initialised by only
formatting the first two tracks, as those tracks always contain all
information necessarry.
Checking the third track on an ESE volume will therefore most likely
fail with a record not found error, as the third track will be empty.
This in turn leads to the device being recognised with a volume size of
0. Attempts to write volume information on the first two tracks then
fail with "no space left on device" errors.
Initialising the first three tracks for an ESE volume is not a viable
solution, because the third track is already a regular track and could
contain user data. With that there is potential for data corruption.
Instead, always only analyse the first two tracks, as it is sufficiant
for both CDL and LDL, and allow ESE volumes to be recognised as well.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Commit 4d284cac76d0 ("[S390] Avoid excessive inlining.") removed
bytes_per_record() which was the only user of the defines ECKD_C0 and
ECKD_F*, and round_up_multiple(). Let's get rid of those.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Commit 72deb455b5ec619f ("block: remove CONFIG_LBDAF") changes
sector_t to u64 unconditionaly, so apply '%llu' for print
sector_t variable.
Fixes: 72deb455b5ec619f ("block: remove CONFIG_LBDAF")
Cc: linux-s390@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The DASD driver incorrectly limits the maximum number of blocks of ECKD
DASD volumes to 32 bit numbers. Volumes with a capacity greater than
2^32-1 blocks are incorrectly recognized as smaller volumes.
This results in the following volume capacity limits depending on the
formatted block size:
BLKSIZE MAX_GB MAX_CYL
512 2047 5843492
1024 4095 8676701
2048 8191 13634816
4096 16383 23860929
The same problem occurs when a volume with more than 17895697 cylinders
is accessed in raw-track-access mode.
Fix this problem by adding an explicit type cast when calculating the
maximum number of blocks.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Dan Carpenter reported the following:
The patch 52898025cf7d: "[S390] dasd: security and PSF update patch
for EMC CKD ioctl" from Mar 8, 2010, leads to the following static
checker warning:
drivers/s390/block/dasd_eckd.c:4486 dasd_symm_io()
error: using offset into zero size array 'psf_data[]'
drivers/s390/block/dasd_eckd.c
4458 /* Copy parms from caller */
4459 rc = -EFAULT;
4460 if (copy_from_user(&usrparm, argp, sizeof(usrparm)))
^^^^^^^
The user can specify any "usrparm.psf_data_len". They choose zero by
mistake.
4461 goto out;
4462 if (is_compat_task()) {
4463 /* Make sure pointers are sane even on 31 bit. */
4464 rc = -EINVAL;
4465 if ((usrparm.psf_data >> 32) != 0)
4466 goto out;
4467 if ((usrparm.rssd_result >> 32) != 0)
4468 goto out;
4469 usrparm.psf_data &= 0x7fffffffULL;
4470 usrparm.rssd_result &= 0x7fffffffULL;
4471 }
4472 /* alloc I/O data area */
4473 psf_data = kzalloc(usrparm.psf_data_len, GFP_KERNEL
| GFP_DMA);
4474 rssd_result = kzalloc(usrparm.rssd_result_len, GFP_KERNEL
| GFP_DMA);
4475 if (!psf_data || !rssd_result) {
kzalloc() returns a ZERO_SIZE_PTR (0x16).
4476 rc = -ENOMEM;
4477 goto out_free;
4478 }
4479
4480 /* get syscall header from user space */
4481 rc = -EFAULT;
4482 if (copy_from_user(psf_data,
4483 (void __user *)(unsigned long)
usrparm.psf_data,
4484 usrparm.psf_data_len))
That all works great.
4485 goto out_free;
4486 psf0 = psf_data[0];
4487 psf1 = psf_data[1];
But now we're assuming that "->psf_data_len" was at least 2 bytes.
Fix this by checking the user specified length psf_data_len.
Fixes: 52898025cf7d ("[S390] dasd: security and PSF update patch for EMC CKD ioctl")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
During offline processing two worker threads are canceled without
freeing the device reference which leads to a hanging offline process.
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Fix a panic that occurs for a device that got an error in
dasd_eckd_check_characteristics() during online processing.
For example the read configuration data command may have failed.
If this error occurs the device is not being set online and the earlier
invoked steps during online processing are rolled back. Therefore
dasd_eckd_uncheck_device() is called which needs a valid private
structure. But this pointer is not valid if
dasd_eckd_check_characteristics() has failed.
Check for a valid device->private pointer to prevent a panic.
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
PTR_RET is deprecated, use PTR_ERR_OR_ZERO instead.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Let the block layer allocate per request data to store
struct dasd_ccw_req. We still need extra preallocated
memory for usage by ccw programs (which vary in length)
and for requests which don't originate from the block
layer.
Link: https://lkml.kernel.org/r/20180530074130.GA6927@infradead.org
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rename struct channel_path_desc to struct channel_path_desc_fmt0
to fit the scheme. Provide a macro for the function wrappers that
gather this and related data from firmware.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Set the XRC timestamps even if XRC is not supported by the storage server
to help debugging the storage server firmware.
Do not advertise valid time stamps if the system time could not be
obtained.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Use 'seq_printf(m, "...%*phN...")' instead of duplicating its
implementation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Prevent that a prefix flag is set based on invalid configuration data.
The validity.verify_base flag should only be set for alias devices.
Usually the unit address type is either one of base, PAV alias or
HyperPAV alias. But in cases where the unit address type is not set or
any other value the validity.verify_base flag might be set as well.
This would lead to follow on errors.
Explicitly check for alias devices and set the validity flag only for
them.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/s390/block/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Stefan Haberland <sth@linux.vnet.ibm.com>
Cc: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Unsigned long long and unsigned long were different in size for 31-bit.
For 64-bit the size for both datatypes is 8 Bytes and since the support
for 31-bit is long gone we can clean up a little and change everything
to unsigned long.
Change get_phys_clock() along the way to accept unsigned long as well so
that the DASD code can be consistent.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The Prefix CCW is not mandatory and raw I/O can also be issued without
it. Check whether the Prefix CCW is supported and if not use the
combination of Define Extent and Locate Record Extended instead.
While at it, sort the variable declarations, replace the gotos with
early exits, and remove an error check at the end which is irrelevant.
Also, remove the XRC check as it is not relevant for raw I/O.
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rename dasd_raw_build_cp() to dasd_eckd_build_cp_raw() to fit the
scheme.
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
We already have define_extent() that prepares necessary data for the
Define Extent CCW. The exact same thing is done in prefix_LRE().
Remove the duplicate code and move commands that were only used in
combination with the Prefix command to define_extent(). One of these
commands needs the blocksize to be specified. Add the blksize parameter
to define_extent() to account for that.
In addition, the check_XRC() function can be made more generic. Do this
and remove the Prefix-specific check_XRC_on_prefix() function.
Furthermore, prefix_LRE() uses fill_LRE_data() to prepare Locate Record
Extended data. Rename the function to fit the scheme better and make it
usable outside of the Prefix context by adding the corresponding CCW
command.
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
On some z/VM systems the query host access command is not supported for
temp disks, though the corresponding feature code is set.
This does not have any impact beside that the information is not available.
Suppress the full blown command reject error messages to not confuse the
user. The error is still logged in the s390dbf.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Some storage servers might not support the query host access feature.
Check if the corresponding feature code is set.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
trivial fix to spelling mistake in literal string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this feature, the DASD device driver more robustly handles DASDs
that are attached via multiple channel paths and are subject to
constant Interface-Control-Checks (IFCCs) and Channel-Control-Checks
(CCCs) or loss of High-Performance-FICON (HPF) functionality on one or
more of these paths.
If a channel path does not work correctly, it is removed from normal
operation as long as other channel paths are available. All extended
error recovery states can be queried and reset via user space
interfaces.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Store flags and path_data per channel path.
Implement get/set functions for various path masks.
The patch does not add functional changes.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
the mdc value can be quite big (like 65535), so we are in undefined
territory when doing the multiplication with the (also signed)
FCX_MAX_DATA_FACTOR as outlined by UBSAN:
UBSAN: Undefined behaviour in drivers/s390/block/dasd_eckd.c:1678:14
signed integer overflow:
65535 * 65536 cannot be represented in type 'int'
CPU: 5 PID: 183 Comm: kworker/u512:1 Not tainted 4.7.0+ #150
Workqueue: events_unbound async_run_entry_fn
000000fb8b59f900 000000fb8b59f990 0000000000000002 0000000000000000
000000fb8b59fa30 000000fb8b59f9a8 000000fb8b59f9a8 000000000011732e
00000000000000a4 0000000000a309e2 0000000000a4c072 000000000000000b
000000fb8b59f9f0 000000fb8b59f990 0000000000000000 0000000000000000
0400000000d83238 000000000011732e 000000fb8b59f990 000000fb8b59f9f0
Call Trace:
([<0000000000117260>] show_trace+0x98/0xa8)
([<00000000001172e0>] show_stack+0x70/0xf0)
([<000000000053ac96>] dump_stack+0x86/0xb8)
([<000000000057f5f8>] ubsan_epilogue+0x28/0x70)
([<000000000057fe9e>] handle_overflow+0xde/0xf0)
([<00000000006c322a>] dasd_eckd_check_characteristics+0x50a/0x550)
([<00000000006b42ca>] dasd_generic_set_online+0xba/0x380)
([<0000000000693d82>] ccw_device_set_online+0x192/0x550)
([<00000000006ac1ae>] dasd_generic_auto_online+0x2e/0x70)
([<0000000000172130>] async_run_entry_fn+0x70/0x270)
([<0000000000165a72>] process_one_work+0x26a/0x638)
([<0000000000165e8a>] worker_thread+0x4a/0x658)
([<000000000016dd9c>] kthread+0x10c/0x110)
([<00000000008963ae>] kernel_thread_starter+0x6/0xc)
([<00000000008963a8>] kernel_thread_starter+0x0/0xc)
As this is a runtime value there is actually no risk of any sane
compiler to detect and (ab)use this undefinedness, but let's make
the multiplication defined by making mdc unsigned.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If the DASD device gets blocked for any reason, e.g. because it is reserved
somewhere, the host_access_count sysfs entry or the host_access_list
debugfs entry may sleep forever. Make it interruptible so that userspace
can use ^C to abort the operation.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
On LPAR the read message buffer command should be executed on the path
it was received on otherwise there is a chance that the CUIR assignment
might be faulty and the wrong channel path is set online/offline.
Fix by setting the path mask accordingly.
On z/VM we might not be able to do I/O on this path but there it does
not matter on which path the read message buffer command is executed.
Therefor implement a retry with an open path mask.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
|
|
It is possible to specify a user offset for the TOD clock, e.g. +2 hours.
The TOD clock will carry this offset even if the clock is synchronized
with STP. This makes the time stamps acquired with get_sync_clock()
useless as another LPAR migth use a different TOD offset.
Use the PTFF instrution to get the TOD epoch difference and subtract
it from the TOD clock value to get a physical timestamp. As the epoch
difference contains the sync check delta as well the LPAR offset value
to the physical clock needs to be refreshed after each clock
synchronization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Implement new DASD IOCTL BIODASDCHECKFMT to check a range of tracks on a
DASD volume for correct formatting. The following characteristics are
checked:
- Block size
- ECKD key length
- ECKD record ID
- Number of records per track
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
With this feature, applications can query if a DASD volume is online
to another operating system instances by checking the online status of
all attached hosts from the storage server.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Reorder lcu and device lock to get rid of the error-prone trylock
mechanism.
The locking order is lcu lock -> device lock.
This protects against changes to the lcu device lists and enables us
to iterate over the devices, take the cdev lock and make changes to
the device structures.
The complicated part is the summary unit check handler that gets an
interrupt on one device of the lcu that leads to structural changes of
the whole lcu itself. This work needs to be done even if devices on
the lcu disappear. So a device independent worker is used.
The old approach tried to update some lcu structures and set up the
lcu worker in the interrupt context with the device lock held.
But this forced the lock order "cdev lock -> lcu lock" that made it
hard to have the lcu lock held and iterate over all devices and change
them.
The new approach is to schedule a device specific worker that gets
out of the interrupt context and rid of the device lock for summary
unit checks. This worker is able to take the lcu lock and schedule the
lcu worker that updates all devices. The time between interrupt and
worker execution is no problem because the devices in the lcu reject
all I/O in this time with an appropriate error. The dasd driver can
deal with this situation and re-drive the I/O later on.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Convert dasd_device.private to be a void pointer to get
rid of a lot of explicit casts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Prepare for new format checking function by renaming functions and
moving reusable code to separate functions:
- Move sanity checks into a new function and make it reusable.
- Move common format code to a new function called
dasd_eckd_format_process_data.
- Create the generic function dasd_eckd_format_build_ccw_req, which
itself will then decide what ccw request is being built according to
the input data. (with upcoming functionality).
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
- Make sure a calling function can rely on data in fdata by resetting to
its initial values
- Move special treatment for track 0 and 1 to dasd_eckd_build_format
- Replace dangerous backward goto with a loop logic
- Add define for number that specifies the maximum amount of CCWs per
request and is used for format_step calculation
- Remove unused variable
Signed-off-by: Jan Höppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Path verification is either done via dasd_eckd_read_conf() which is
triggered during online processing and resume or via
do_path_verification_work() which is triggered after path events.
The dasd_eckd_read_conf() version added paths unconditionally and did
not check if the path mask was empty. This led to devices having the
disconnected stop flag set but a valid path mask. So they where not
working although they had paths validated successfully. After a resume
this state could even not be solved with additional paths added.
Fix by checking for an empty path mask in dasd_eckd_read_conf() and
clearing the device stop bits for a newly added channel path.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For a valid PAV assignment the DASD driver needs to notice possibly
changed configuration data. Thus the failing of read configuration
data should also fail the device restore to prevent invalid PAV
assignment. The failed device may get restored after additional paths
get available later on.
If the restore fails after the device was added to the lcu alias
handling it needs to be removed from the alias handling before exiting
the restore function.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The configuration data is stored per path and also the first valid
configuration data per device. When dasd_eckd_read_conf is called
again after a path got lost the device configuration data is cleared
but possibly not the per path configuration data. This might lead to a
double free when the lost path gets operational again.
Fix by clearing all per path configuration data when the first valid
configuration data is received and stored.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
We often need to correlate an 8 bit path mask with the position
in a channel path array. Introduce and use pathmask_to_pos for
that task.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Remove two more statements which always evaluate to 'false'.
These are more leftovers from the 31 bit era.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch adds an enhanced detection for control unit initiated
reconfiguration request scope.
The first approach assumed the scope of the reconfiguration request
to be restricted to the path on which the message was received.
The enhanced approach determines the full scope of the reconfiguration
request by evaluating additional path and device selection information
contained in the reconfiguration message.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
DASD path verification requires the usage of sleep_on_immediatly to
ensure that no other I/O request is blocking the recovery of
disconnected devices. But two concurrent path verification workers for
the same device may kill each others requests due to the usage of the
immediate sleep_on function. This may lead to unsuccessful path
verifications.
Prevent that two parallel path verification workers conflict with
each other by implementing a device flag signalling a already running
worker.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
Stefan Haberland
Jan Höppner
Ming Lei
Peter Oberparleiter
Gustavo A. R. Silva
Sebastian Ott
Sebastian Ott
Stefan Haberland
Christophe JAILLET
Greg Kroah-Hartman
Jan Höppner
Colin Ian King
Linus Torvalds
Christian Borntraeger
Martin Schwidefsky
Stefan Haberland
Heiko Carstens