Age | Commit message (Collapse) | Author | Files | Lines |
|
Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size. But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort. Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.
Fixes: 4e7485066373 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The consume_skb() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]
The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an unlikely case, use unlikely() on it seems logical.
Signed-off-by: xiaolinkui <xiaolinkui@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As reported by Aaro this patch causes network problems on
MIPS Loongson platform. Therefore revert it.
Fixes: f072218cca5b ("r8169: remove not needed call to dma_sync_single_for_device")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Timestamps are currently communicated to user space as 'struct
timespec', which is not considered y2038 safe since it uses a 32-bit
signed value for seconds.
Fix this while the API is still not part of any official kernel release
by using 64-bit nanoseconds timestamps instead.
Fixes: ca30707dee2b ("drop_monitor: Add packet alert mode")
Fixes: 5e58109b1ea4 ("drop_monitor: Add support for packet alert mode for hardware drops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the RDMA cookie and RX timestamp to the usercopy whitelist.
After the introduction of hardened usercopy whitelisting
(https://lwn.net/Articles/727322/), a warning is displayed when the
RDMA cookie or RX timestamp is copied to userspace:
kernel: WARNING: CPU: 3 PID: 5750 at
mm/usercopy.c:81 usercopy_warn+0x8e/0xa6
[...]
kernel: Call Trace:
kernel: __check_heap_object+0xb8/0x11b
kernel: __check_object_size+0xe3/0x1bc
kernel: put_cmsg+0x95/0x115
kernel: rds_recvmsg+0x43d/0x620 [rds]
kernel: sock_recvmsg+0x43/0x4a
kernel: ___sys_recvmsg+0xda/0x1e6
kernel: ? __handle_mm_fault+0xcae/0xf79
kernel: __sys_recvmsg+0x51/0x8a
kernel: SyS_recvmsg+0x12/0x1c
kernel: do_syscall_64+0x79/0x1ae
When the whitelisting feature was introduced, the memory for the RDMA
cookie and RX timestamp in RDS was not added to the whitelist, causing
the warning above.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Tested-by: Jenny <jenny.x.xu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return code value could be non deterministic in case of wrong size read.
With this patch, if such error occurs, set rc to be -EIO.
In addition, mlx5_hv_config_common() supports reading of
HV_CONFIG_BLOCK_SIZE_MAX bytes only, fix to early return error with
bad input.
Fixes: 913d14e86657 ("net/mlx5: Add wrappers for HyperV PCIe operations")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need a similar fix for ipv6 as Commit 0761680d5215 ("net: ipv4: fix
listify ip_rcv_finish in case of forwarding") does for ipv4.
This issue can be reprocuded by syzbot since Commit 323ebb61e32b ("net:
use listified RX for handling GRO_NORMAL skbs") on net-next. The call
trace was:
kernel BUG at include/linux/skbuff.h:2225!
RIP: 0010:__skb_pull include/linux/skbuff.h:2225 [inline]
RIP: 0010:skb_pull+0xea/0x110 net/core/skbuff.c:1902
Call Trace:
sctp_inq_pop+0x2f1/0xd80 net/sctp/inqueue.c:202
sctp_endpoint_bh_rcv+0x184/0x8d0 net/sctp/endpointola.c:385
sctp_inq_push+0x1e4/0x280 net/sctp/inqueue.c:80
sctp_rcv+0x2807/0x3590 net/sctp/input.c:256
sctp6_rcv+0x17/0x30 net/sctp/ipv6.c:1049
ip6_protocol_deliver_rcu+0x2fe/0x1660 net/ipv6/ip6_input.c:397
ip6_input_finish+0x84/0x170 net/ipv6/ip6_input.c:438
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip6_input+0xe4/0x3f0 net/ipv6/ip6_input.c:447
dst_input include/net/dst.h:442 [inline]
ip6_sublist_rcv_finish+0x98/0x1e0 net/ipv6/ip6_input.c:84
ip6_list_rcv_finish net/ipv6/ip6_input.c:118 [inline]
ip6_sublist_rcv+0x80c/0xcf0 net/ipv6/ip6_input.c:282
ipv6_list_rcv+0x373/0x4b0 net/ipv6/ip6_input.c:316
__netif_receive_skb_list_ptype net/core/dev.c:5049 [inline]
__netif_receive_skb_list_core+0x5fc/0x9d0 net/core/dev.c:5097
__netif_receive_skb_list net/core/dev.c:5149 [inline]
netif_receive_skb_list_internal+0x7eb/0xe60 net/core/dev.c:5244
gro_normal_list.part.0+0x1e/0xb0 net/core/dev.c:5757
gro_normal_list net/core/dev.c:5755 [inline]
gro_normal_one net/core/dev.c:5769 [inline]
napi_frags_finish net/core/dev.c:5782 [inline]
napi_gro_frags+0xa6a/0xea0 net/core/dev.c:5855
tun_get_user+0x2e98/0x3fa0 drivers/net/tun.c:1974
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2020
Fixes: d8269e2cbf90 ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()")
Fixes: 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL skbs")
Reported-by: syzbot+eb349eeee854e389c36d@syzkaller.appspotmail.com
Reported-by: syzbot+4a0643a653ac375612d1@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a helper function "rtl_eee_enable" for setting EEE. Besides, I
move r8153_eee_en() and r8153b_eee_en(). And, I remove r8152b_enable_eee(),
r8153_set_eee(), and r8153b_set_eee().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saving the settings of EEE to avoid they become the default settings
after reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update response packet length for the following commands per NC-SI spec
- Get Controller Packet Statistics
- Get NC-SI Statistics
- Get NC-SI Pass-through Statistics command
Signed-off-by: Ben Wei <benwei@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have the DT validation in place, let's convert the device tree
bindings for the Synopsys DWMAC Glue for Amlogic SoCs over to a YAML schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Amlogic Meson DWMAC glue bindings needs a second reg cells for the
glue registers, thus update the reg minItems/maxItems to allow more
than a single reg cell.
Also update the allwinner,sun7i-a20-gmac.yaml derivative schema to specify
maxItems to 1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed a bug where driver was breaking out of the loop and
reporting an error without retrying first.
Signed-off-by: Marcin Formela <marcin.formela@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.
So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.
The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).
Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: Adrian Podlawski <adrian.podlawski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: huhai <huhai@kylinos.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Similar to the ixgbe issue fixed in:
655c91414579 ("ixgbe: Check DDM existence in transceiver before access)
i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.
Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.
As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:
drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]
When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.
The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.
Fixes: 0a862b43acc6 ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.
The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.
As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.
Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.
The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.
The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.
Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations. This will be used as an
infrastructure in the downstream patch for software communication.
This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This interface driver is a helper driver allows other drivers to
have a common interface with the Hyper-V PCI frontend driver.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Windows SR-IOV provides a backchannel mechanism in software for communication
between a VF driver and a PF driver. These "configuration blocks" are
similar in concept to PCI configuration space, but instead of doing reads and
writes in 32-bit chunks through a very slow path, packets of up to 128 bytes
can be sent or received asynchronously.
Nearly every SR-IOV device contains just such a communications channel in
hardware, so using this one in software is usually optional. Using the
software channel, however, allows driver implementers to leverage software
tools that fuzz the communications channel looking for vulnerabilities.
The usage model for these packets puts the responsibility for reading or
writing on the VF driver. The VF driver sends a read or a write packet,
indicating which "block" is being referred to by number.
If the PF driver wishes to initiate communication, it can "invalidate" one or
more of the first 64 blocks. This invalidation is delivered via a callback
supplied by the VF driver by this driver.
No protocol is implied, except that supplied by the PF and VF drivers.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow tracing neigh state during neigh update task that is executed on
workqueue and is scheduled by neigh state change event.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_rep_neigh_update >> set_event
># cat trace
...
kworker/u48:7-2221 [009] ...1 1475.387435: mlx5e_rep_neigh_update:
netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow tracing result of neigh used value update task that is executed
periodically on workqueue.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_tc_update_neigh_used_value >> set_event
># cat trace
...
kworker/u48:4-8806 [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value:
netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implemented following tracepoints:
1. Configure flower (mlx5e_configure_flower)
2. Delete flower (mlx5e_delete_flower)
3. Stats flower (mlx5e_stats_flower)
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_configure_flower >> set_event
># cat trace
...
tc-6535 [019] ...1 2672.404466: mlx5e_configure_flower: cookie=0000000067874a55 actions= REDIRECT
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock and prevent neigh update code from
accessing uninitialized flows when executing concurrently with tc, extend
mlx5e_tc_flow with 'init_done' completion. Modify helper
mlx5e_take_all_encap_flows() to wait for flow completion after obtaining
reference to it. Modify mlx5e_tc_encap_flows_del() and
mlx5e_tc_encap_flows_add() to skip flows that don't have OFFLOADED flag
set, which can happen if concurrent flow initialization failed.
This commit finishes neigh update refactoring for concurrent execution
started in previous change in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to remove dependency on rtnl lock and allow neigh update workqueue
task to execute concurrently with tc, refactor mlx5e_rep_neigh_update() for
concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes. To do this properly, the initial encap state check is moved from
mlx5e_rep_neigh_update() into mlx5e_rep_update_flows() to be performed
under encap_tbl_lock protection.
- Wait for encap to be fully initialized before accessing it by means of
'res_ready' completion.
- Add mlx5e_take_all_encap_flows() helper which is used to construct a
temporary list of flows and efi indexes that is used to access current
encap data in flow which can be attached to multiple encaps
simultaneously. Release the flows from temporary list after
encap_tbl_lock critical section. This is necessary because
mlx5e_flow_put() can't be called while holding encap_tbl_lock.
- Modify mlx5e_tc_encap_flows_add() and mlx5e_tc_encap_flows_del() to work
with user-provided list of flows built by mlx5e_take_all_encap_flows(),
instead of traversing encap flow list directly.
This is first step in complex neigh update refactoring, which is finished
by following commit in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to remove dependency on rtnl lock and allow neigh used value
update workqueue task to execute concurrently with tc, refactor
mlx5e_tc_update_neigh_used_value() for concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes.
- Save offloaded encap flows to temporary list and release them after encap
entry is updated. Add mlx5e_put_encap_flow_list() helper which is
intended to be shared with neigh update code in following patch in this
series. This is necessary because mlx5e_flow_put() can't be called while
holding encap_tbl_lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on encap
list to their rcu counterparts and extending encap structure with rcu_head
to free the encap instances after rcu grace period. Use rcu read lock when
traversing encap list. Implement helper mlx5e_get_next_valid_encap()
function that is used by mlx5e_tc_update_neigh_used_value() to safely
iterate over valid entries of nhe->encap_list.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock, always take neigh update encap lock when
modifying neigh update hash table and list. Originally, this lock was only
used to synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Take lock in encap
entry attach function to prevent concurrent modifications of neigh update
hash table and list.
Taking the encap lock when creating new nhe introduces a problem that we
need to allocate new entry with sleeping GFP_KERNEL flag while holding a
spinlock. However, since previous patch in this series has already
converted lookup in netevent handler function to user rcu read lock instead
of encap lock, we can safely convert the lock type to mutex.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock and to allow unlocked iteration over list
of neigh hash entries, extend nhe with rcu. Change operations on neigh list
to their rcu counterparts and free neigh hash entry with rcu timeout.
Introduce mlx5e_get_next_nhe() helper that is used to iterate over rcu
neigh list with reference to nhe taken.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Neigh entry has reference counter, however it is only used when scheduling
neigh update event. In all other cases reference to neigh entry is not
taken while working with it. Neigh code relies on synchronization provided
by rtnl lock and uses encap list size as implicit reference counter.
To remove dependency on rtnl lock, always take reference to neigh entry
while using it. Remove neigh entry from hash table and delete it only when
reference counter reaches zero. This can result spurious neigh update
events, when there is an event on entry that has zero encaps attached.
However, such events are rare and properly handled by neigh update handler.
Extend encap entry with reference to neigh hash entry in order to be able
to directly release it when encap is detached, instead of lookup nhe by key
through hash table. Extend nhe with reference to device priv structure to
guarantee correctness when nhe is used with stack devices, bond setup, in
which case it is non-trivial to determine correct device when releasing the
nhe.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|