Age | Commit message (Collapse) | Author | Files | Lines |
|
Like the NFP4000 and NFP6000, the NFP5000 as an erratum where reading/
writing to PCI config space addresses above 0x600 can cause the NFP to
generate PCIe completion timeouts.
Limit the NFP5000's PF's config space size to 0x600 bytes as is already
done for the NFP4000 and NFP6000.
The NFP5000's VF is 0x6003 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tony Egan <tony.egan@netronome.com>
|
|
If flag IRQCHIP_ONESHOT_SAFE isn't set for an irqchip and we have a
threaded interrupt with no primary handler, flag IRQF_ONESHOT needs to be
set for the interrupt, causing some overhead in the threaded interrupt
handler. For more detailed explanation also check following comment in
__setup_irq():
The interrupt was requested with handler = NULL, so we use the default
primary handler for it. But it does not have the oneshot flag set. In
combination with level interrupts this is deadly, because the default
primary handler just wakes the thread, then the irq lines is reenabled,
but the device still has the level irq asserted. Rinse and repeat....
While this works for edge type interrupts, we play it safe and reject
unconditionally because we can't say for sure which type this interrupt
really has. The type flags are unreliable as the underlying chip
implementation can override them.
Another comment in __setup_irq() gives a hint already that this
overhead can be avoided for PCI-MSI:
Some irq chips like MSI based interrupts are per se one shot safe. Check
the chip flags, so we can avoid the unmask dance at the end of the
threaded handler for those.
Following this let's mark all PCI-MSI irqchips as oneshot-safe.
See also discussion here:
https://lkml.kernel.org/r/alpine.DEB.2.21.1808032136490.1658@nanos.tec.linutronix.de
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously we checked the timeout before checking the VPD access completion
bit. On a very heavily loaded system this can cause VPD access to timeout.
Check the completion bit before checking the timeout.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There are a lot of examples in the kernel where PCI_VDEVICE() is used and
still looks not so convenient due to additional driver_data field attached.
Introduce PCI_DEVICE_DATA() macro to fully describe device ID entry in
shortest possible form. For example,
before:
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MRFLD),
(kernel_ulong_t) &dwc3_pci_mrfld_properties, },
after:
{ PCI_DEVICE_DATA(INTEL, MRFLD, &dwc3_pci_mrfld_properties) },
Drivers can be converted later on in independent way.
While here, remove the unused macro with the same name from Ralink wireless
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # for rt2x00
|
|
In commit 27d868b5e6cf ("PCI: Set MPS to match upstream bridge"), we made
sure every device's MPS setting matches its upstream bridge, making it more
likely that a hot-added device will work in a system with an optimized MPS
configuration.
Recently I've started encountering systems where the endpoint device's MPSS
capability is less than its Root Port's current MPS value, thus the
endpoint is not capable of matching its upstream bridge's MPS setting (see:
bugzilla via "Link:" below). This leaves the system vulnerable - the
upstream Root Port could respond with larger TLPs than the device can
handle, and the device will consider them to be 'Malformed'.
One could use the "pci=pcie_bus_safe" kernel parameter to work around the
issue, but that forces a user to supply a kernel parameter to get the
system to function reliably and may end up limiting MPS settings of other
unrelated, sub-topologies which could benefit from maintaining their larger
values.
Augment Keith's approach to include tuning down a Root Port's MPS setting
when its hot-added endpoint device is not capable of matching it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
|
|
PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs. Just prior to the table it states:
"PF and VF functionality is defined in Section 7.5.3.4 except where
noted in Table 9-16. For VF fields marked 'RsvdP', the PF setting
applies to the VF."
All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's. Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Fixes: 27d868b5e6cf ("PCI: Set MPS to match upstream bridge")
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.3+
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
Cc: Jon Mason <jdmason@kudzu.us>
|
|
Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679#c134
Reported-and-tested-by: Felix Blüthner <f.bluethner@mailbox.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When both ends of a PCIe Link are capable of a higher bandwidth than is
currently in use, the Link is said to be "downtrained". A downtrained Link
may indicate hardware or configuration problems in the system, but it's
hard to identify such Links from userspace.
Refactor pcie_print_link_status() so it continues to always print PCIe
bandwidth information, as several NIC drivers desire.
Add a new internal __pcie_print_link_status() to emit a message only when a
device's bandwidth is constrained by the fabric and call it from the PCI
core for all devices, which identifies all downtrained Links. It also
emits messages for a few cases that are technically not downtrained, such
as a x4 device in an open-ended x1 slot.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog, move __pcie_print_link_status() declaration to
drivers/pci/, rename pcie_check_upstream_link() to
pcie_report_downtraining()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Intel Sunrise Point PCH hardware has an implementation of the ACS bits that
does not comply with the PCIe standard. Add a device-specific quirk,
pci_quirk_disable_intel_spt_pch_acs_redir() to disable ACS Redirection on
this system.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Intel Sunrise Point (SPT) PCH hardware has an implementation of the ACS
bits that does not comply with the PCIe standard. To deal with this we
need device-specific quirks to disable ACS redirection.
Add a new pci_dev_specific_disable_acs_redir() quirk and a new
.disable_acs_redir() function pointer for use by non-compliant devices. No
functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch, move
pci_dev_specific_disable_acs_redir() declarations to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Convert the search for device-specific ACS enable quirks from searching a
NULL-terminated array to iterating through the array, which is always
fixed-size anyway. No functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch for reviewability]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
|
|
To support peer-to-peer traffic on a segment of the PCI hierarchy, we must
disable the ACS redirect bits for select PCI bridges. The bridges must be
selected before the devices are discovered by the kernel and the IOMMU
groups created. Therefore, add a kernel command line parameter to specify
devices which must have their ACS bits disabled.
The new parameter takes a list of devices separated by a semicolon. Each
device specified will have its ACS redirect bits disabled. This is
similar to the existing 'resource_alignment' parameter.
The ACS Request P2P Request Redirect, P2P Completion Redirect and P2P
Egress Control bits are disabled, which is sufficient to always allow
passing P2P traffic uninterrupted. The bits are set after the kernel
(optionally) enables the ACS bits itself. It is also done regardless of
whether the kernel or platform firmware sets the bits.
If the user tries to disable the ACS redirect for a device without the ACS
capability, print a warning to dmesg.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: reorder to add the generic code first and move the
device-specific quirk to subsequent patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
|
|
When specifying PCI devices on the kernel command line using a
bus/device/function address, bus numbers can change when adding or
replacing a device, changing motherboard firmware, or applying kernel
parameters like "pci=assign-buses". When bus numbers change, it's likely
the command line tweak will be applied to the wrong device.
Therefore, it is useful to be able to specify devices with a base bus
number and the path of devfns needed to get to it, similar to the "device
scope" structure in the Intel VT-d spec, Section 8.3.1.
Thus, we add an option to specify devices in the following format:
[<domain>:]<bus>:<device>.<func>[/<device>.<func>]*
The path can be any segment within the PCI hierarchy of any length and
determined through the use of 'lspci -t'. When specified this way, it is
less likely that a renumbered bus will result in a valid device
specification and the tweak won't be applied to the wrong device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
|
|
Separate out the code to match a PCI device with a string (typically
originating from a kernel parameter) from the
pci_specified_resource_alignment() function into its own helper function.
While we are at it, this change fixes the kernel style of the function
(fixing a number of long lines and extra parentheses).
Additionally, make the analogous change to the kernel parameter
documentation: Separate the description of how to specify a PCI device
into its own section at the head of the "pci=" parameter.
This patch should have no functional alterations.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
|
|
Move declarations for these functions:
pci_dev_specific_acs_enabled()
pci_dev_specific_enable_acs()
from include/linux/pci.h to drivers/pci/pci.h because nothing outside the
PCI core needs to use them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a device-specific reset for Intel DC P3700 NVMe device which exhibits a
timeout failure in drivers waiting for the ready status to update after
NVMe enable if the driver interacts with the device too soon after FLR. As
this has been observed in device assignment scenarios, resolve this with a
device-specific reset quirk to add an additional, heuristically determined,
delay after the FLR completes.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1592654
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The Samsung SM961/PM961 (960 EVO) sometimes fails to return from FLR with
the PCI config space reading back as -1. A reproducible instance of this
behavior is resolved by clearing the enable bit in the NVMe configuration
register and waiting for the ready status to clear (disabling the NVMe
controller) prior to FLR.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1542494
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pcie_flr() suggests pcie_has_flr() to ensure that PCIe FLR support is
present prior to calling. pcie_flr() is exported while pcie_has_flr()
is not. Resolve this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This comment has been there since the driver was introduced, but seems
to be a leftover from previous iterations of the driver. Indeed, we do
not lookup in a list to find the register ranges that matches the
given port/lane, as the "reg" property is in each sub-node
representing a PCI port. There is no lookup involved at all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Rather than using the ARM-specific pci_common_init_dev() API, use the
pci_host_bridge logic directly.
Unfortunately, we can't use devm_of_pci_get_host_bridge_resources(),
because the DT binding for describing PCIe apertures for this PCI
controller is a bit special, and we cannot retrieve them from the
'ranges' property. Therefore, we still have some special code to
handle this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Instead of hardcoding the remapping of IO_SPACE_LIMIT - SZ_64K, use
resource_size().
However, we cannot use just IO_SPACE_LIMIT, because pci_ioremap_io() has
a bug and doesn't allow remapping the last 64 KB before IO_SPACE_LIMIT,
so we ensure that we do not exceed this limit. When the pci_ioremap_io()
issue is fixed, this work around can be dropped.
Note that this workaround already existed, since we were mapping only
up to IO_SPACE_LIMIT - SZ_64K.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: tweaked the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
If there is no PCI I/O aperture configured in the Device Tree, it does
not make sense to create the virtual mapping for the PCI I/O space,
since we will anyway not create the MBus window that will allow to
access it. Therefore, do the pci_ioremap_io() only if necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
pcie->realio.end should be the address of last byte of the area,
therefore using resource_size() of another resource is not correct, we
must substract 1 to get the address of the last byte.
Fixes: 11be65472a427 ("PCI: mvebu: Adapt to the new device tree layout")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This is already done earlier in mvebu_pcie_probe().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Several PCI core files include pci-aspm.h even though they don't need
anything provided by that file. Remove the unnecessary includes of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
|
|
This part of the iwlwifi driver doesn't need anything provided by
pci-aspm.h, so remove the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The ath9k driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The igb driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The sysfs_match_string() helper returns index of the matching string in an
array. Use it in pcie_aspm_set_policy() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: squash sysfs_match_string() fix into original patch for issue
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There isn't a hard dependency of the Xilinx AXI-PCIe host bridge on any
architecture. For example: at SiFive we map RISC-V cores to Xilinx FPGAs
and connect the Xilinx IP via a TileLink adapter, so the RISC-V Linux
port will need to be able to enable PCIE_XILINX in order to have PCIe
support.
This patch decouples the PCIE_XILINX support from ARCH. Instead it just
depends on OF, which is the only true dependency.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: switch to OF instead of OF_PCI now that the latter is gone]
Signed-off-by: Christoph Hellwig <hch@lst.de>
[lorenzo.pieralisi@arm.com: trimmed the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Current DMA direction definitions in pci-dma-compat.h and dma-direction.h
are mirrored in value. Unify them to enhance readability and avoid
possible inconsistency.
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
|
|
PCI_EXP_AER_FLAGS was defined twice (with identical definitions), once
under #ifdef CONFIG_ACPI_APEI, and again at the top level. This looks like
my merge error from these commits:
fd3362cb73de ("PCI/AER: Squash aerdrv_core.c into aerdrv.c")
41cbc9eb1a82 ("PCI/AER: Squash ecrc.c into aerdrv.c")
Remove the duplicate PCI_EXP_AER_FLAGS definition.
Fixes: 41cbc9eb1a82 ("PCI/AER: Squash ecrc.c into aerdrv.c")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
|
|
On driver probe and on resume from system sleep, pciehp checks the
Presence Detect State bit in the Slot Status register to bring up an
occupied slot or bring down an unoccupied slot. Both code paths are
identical, so deduplicate them per Mika's request.
On probe, an additional check is performed to disable power of an
unoccupied slot. This can e.g. happen if power was enabled by BIOS.
It cannot happen once pciehp has taken control, hence is not necessary
on resume: The Slot Control register is set to the same value that it
had on suspend by pci_restore_state(), so if the slot was occupied,
power is enabled and if it wasn't, power is disabled. Should occupancy
have changed during the system sleep transition, power is adjusted by
bringing up or down the slot per the paragraph above.
To allow for deduplication of the presence check, move the power check
to pcie_init(). This seems safer anyway, because right now it is
performed while interrupts are already enabled, and although I can't
think of a scenario where pciehp_power_off_slot() and the IRQ thread
collide, it does feel brittle.
However this means that pcie_init() may now write to the Slot Control
register before the IRQ is requested. If both the CCIE and HPIE bits
happen to be set, pcie_wait_cmd() will wait for an interrupt (instead
of polling the Command Completed bit) and eventually emit a timeout
message. Additionally, if a level-triggered INTx interrupt is used,
the user may see a spurious interrupt splat. Avoid by disabling
interrupts before disabling power. (Normally the HPIE and CCIE bits
should be clear on probe, but conceivably they may already have been
set e.g. by BIOS.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Per Mika's request, add an explicit break to the last case of switch
statements everywhere in pciehp to be more defensive towards future
amendments.
Per Gustavo's request, mark all non-empty implicit fallthroughs with a
comment to silence warnings triggered by -Wimplicit-fallthrough=2.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Thunderbolt controllers can be runtime suspended to D3cold to save ~1.5W.
This requires that runtime D3 is allowed on its PCIe ports, so whitelist
them.
The 2015 BIOS cutoff that we've instituted for runtime D3 on PCIe ports
is unnecessary on Thunderbolt because we know that even the oldest
controller, Light Ridge (2010), is able to suspend its ports to D3 just
fine -- specifically including its hotplug ports. And the power saving
should be afforded to machines even if their BIOS predates 2015.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Andreas Noever <andreas.noever@gmail.com>
|
|
Previously we blacklisted PCIe hotplug ports for runtime D3 because:
(a) Ports handled by the firmware must not be transitioned to D3 by the
OS behind the firmware's back:
https://bugzilla.kernel.org/show_bug.cgi?id=53811
(b) Ports handled natively by the OS lacked runtime D3 support in the
pciehp driver.
We've just rectified the latter, so allow users to manually enable and
test it by passing pcie_port_pm=force on the command line. Vendors are
thus put in a position to validate hotplug ports for runtime D3 and
perhaps we can someday enable it by default, but with a BIOS cutoff date.
Ashok Raj tested runtime D3 on hotplug ports of a SkyLake Xeon-SP in
2017 and encountered Hardware Error NMIs, so this feature clearly cannot
be enabled for everyone yet:
https://lkml.kernel.org/r/20170503180426.GA4058@otc-nc-03
While at it, remove an erroneous code comment I added with 97a90aee5dab
("PCI: Consolidate conditions to allow runtime PM on PCIe ports") which
claims that parents of a hotplug port must stay awake lest interrupts
cannot be delivered. That has turned out to be wrong at least for
Thunderbolt hotplug ports.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
|
When performing a function reset via sysfs, the device's config space is
accessed in places such as pcie_flr() and its MMIO space is accessed e.g.
in reset_ivb_igd(), so ensure accessibility by resuming the device to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
|
Ensure accessibility of a hotplug port's config space when accessed via
sysfs by resuming its parent to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
|
pciehp's IRQ thread ensures accessibility of the port by runtime resuming
its parent to D0. However when the slot is enabled/disabled, the port
itself needs to be in D0 because its secondary bus is accessed in:
pciehp_check_link_status(),
pciehp_configure_device() (both called from board_added())
and
pciehp_unconfigure_device() (called from remove_board()).
Thus, acquire a runtime PM ref on enable/disablement of the slot.
Yinghai Lu additionally discovered that some SkyLake servers feature a
Power Controller for their PCIe hotplug ports (PCIe r3.1, sec 6.7.1.8)
which requires the port to be in D0 when invoking
pciehp_power_on_slot() (likewise called from board_added()).
If slot power is turned on while in D3hot, link training later fails:
https://lkml.kernel.org/r/20170205073454.GA253@wunner.de
The spec is silent about such a requirement, but it seems prudent to
assume that any hotplug port with a Power Controller may need this.
The present commit holds a runtime PM ref whenever slot power is turned
on and off, but it doesn't keep the port in D0 as long as slot power is
on. If vendors determine that's necessary, they need to amend pciehp to
acquire a runtime PM ref in pciehp_power_on_slot() and release one in
pciehp_power_off_slot().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
|
If a hotplug port is able to send an interrupt, one would naively assume
that it is accessible at that moment. After all, if it wouldn't be
accessible, i.e. if its parent is in D3hot and the link to the hotplug
port is thus down, how should an interrupt come through?
It turns out that assumption is wrong at least for Thunderbolt: Even
though its parents are in D3hot, a Thunderbolt hotplug port is able to
signal interrupts. Because the port's config space is inaccessible and
resuming the parents may sleep, the hard IRQ handler has to defer
runtime resuming the parents and reading the Slot Status register to the
IRQ thread.
If the hotplug port uses a level-triggered INTx interrupt, it needs to
be masked until the IRQ thread has cleared the signaled events. For
simplicity, this commit also masks edge-triggered MSI/MSI-X interrupts.
Note that if the interrupt is shared (which can only happen for INTx),
other devices are starved from receiving interrupts until the IRQ thread
is scheduled, has runtime resumed the hotplug port's parents and has
read and cleared the Slot Status register.
That delay is dominated by the 10 ms D3hot->D0 transition time of each
parent port. The worst case is a Thunderbolt downstream port at the
end of a daisy chain: There may be up to six Thunderbolt controllers
in-between it and the root port, each comprising an upstream and
downstream port, plus its own upstream port. That's 13 x 10 = 130 ms.
Possible mitigations are polling the interrupt while it's disabled or
reducing the d3_delay of Thunderbolt ports if possible.
Open code masking of the interrupt instead of requesting it with the
IRQF_ONESHOT flag to minimize the period during which it is masked.
(IRQF_ONESHOT unmasks the IRQ only after the IRQ thread has finished.)
PCIe r4.0 sec 6.7.3.4 states that "If wake generation is required by the
associated form factor specification, a hotplug capable Downstream Port
must support generation of a wakeup event (using the PME mechanism) on
hotplug events that occur when the system is in a sleep state or the
Port is in device state D1, D2, or D3Hot."
This would seem to imply that PME needs to be enabled on the hotplug
port when it is runtime suspended. pci_enable_wake() currently doesn't
enable PME on bridges, it may be necessary to add an exemption for
hotplug bridges there. On "Light Ridge" Thunderbolt controllers, the
PME_Status bit is not set when an interrupt occurs while the hotplug
port is in D3hot, even if PME is enabled. (I've tested this on a Mac
and we hardcode the OSC_PCI_EXPRESS_PME_CONTROL bit to 0 on Macs in
negotiate_os_control(), modifying it to 1 didn't change the behavior.)
(Side note: Section 6.7.3.4 also states that "PME and Hot-Plug Event
interrupts (when both are implemented) always share the same MSI or
MSI-X vector". That would only seem to apply to Root Ports, however
the section never mentions Root Ports, only Downstream Ports. This is
explained in the definition of "Downstream Port" in the "Terms and
Acronyms" section of the PCIe Base Spec: "The Ports on a Switch that
are not the Upstream Port are Downstream Ports. All Ports on a Root
Complex are Downstream Ports.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
|
|
Upon resume from system sleep, the Slot Control register is written via:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
PCIe r4.0, sec 6.7.3.2 says that after "issuing a write transaction that
targets any portion of the Port's Slot Control register, [...] software
must wait for [the] command to complete before issuing the next command".
pciehp currently fails to enforce that rule after the above-mentioned
write. Fix it.
(Moving restoration of the Slot Control register to pciehp doesn't seem
to make sense because the other PCIe hotplug drivers may need it as
well.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840feab ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Replace suspend_iter() and resume_iter() with a single function pm_iter()
to allow addition of port service callbacks for further power management
phases without having to add another iterator each time.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The ->reset_slot callback introduced by commits:
2e35afaefe64 ("PCI: pciehp: Add reset_slot() method") and
06a8d89af551 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
|
|
If we have a threaded interrupt with the handler being NULL, then
request_threaded_irq() -> __setup_irq() will complain and bail out if the
IRQF_ONESHOT flag isn't set. Therefore check for the handler being NULL
and set IRQF_ONESHOT in this case.
This change is needed to migrate the mei_me driver to
pci_alloc_irq_vectors() and pci_request_irq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
There is nothing arch-specific about PCI or dma-debug, so call
dma_debug_add_bus() from the PCI core just after registering the bus type.
Most of dma-debug is already generic; this just adds reporting of pending
dma-allocations on driver unload for arches other than powerpc, sh, and
x86.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
|
|
commit 9af6bcb11e12 ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver") did not add the configuration and build infrastructure to
configure and build the mobiveil controller driver, so at present the
driver code is in the kernel but cannot be compiled.
Add the mobiveil controller driver Kconfig/Makefile infrastructure.
Fixes: 9af6bcb11e12 ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
|
|
PCI mobiveil host controller driver currently fails to compile
with the following error:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_probe':
drivers/pci/controller/pcie-mobiveil.c:788:8: error: implicit
declaration of function 'devm_of_pci_get_host_bridge_resources'; did you
mean 'pci_get_host_bridge_device'?
[-Werror=implicit-function-declaration]
ret = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pci_get_host_bridge_device
Add the missing include file to pull in the required function declaration.
Fixes: 9af6bcb11e12 ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
|
|
The field pcie_reg_base in struct mobiveil_pcie represents a physical
address so it should be of phys_addr_t type rather than void __iomem*;
this results in the following compilation warnings:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_parse_dt':
drivers/pci/controller/pcie-mobiveil.c:326:22: warning: assignment makes
pointer from integer without a cast [-Wint-conversion]
pcie->pcie_reg_base = res->start;
^
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_enable_msi':
drivers/pci/controller/pcie-mobiveil.c:485:25: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t msg_addr = pcie->pcie_reg_base;
^~~~
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_compose_msi_msg':
drivers/pci/controller/pcie-mobiveil.c:640:21: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t addr = pcie->pcie_reg_base + (data->hwirq * sizeof(int));
Fix the type and with it the compilation warnings.
Fixes: 9af6bcb11e12 ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
|