| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2019-12-18 | s390/qeth: make use of napi_schedule_irqoff() |   Julian Wiedmann | 1 | -1/+1 | |
| qeth_qdio_start_poll() is called from the qdio layer's IRQ handler, while IRQs are masked. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: consolidate helpers for capability checking | Julian Wiedmann | 3 | -61/+27 | |
| Convert the old code to use struct qeth_ipa_caps, and while at it remove all unused helper macros. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: stop yielding the ip_lock during IPv4 registration | Julian Wiedmann | 2 | -33/+2 | |
| As commit df2a2a5225cc ("s390/qeth: convert IP table spinlock to mutex") converted the ip_lock to a mutex, we no longer have to yield it while the subsequent IO sleep-waits for completion. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: don't raise NETDEV_REBOOT event from L3 offline path | Julian Wiedmann | 1 | -6/+0 | |
| This is a leftover from back when a recovery action didn't go through dev_close(), and was meant to shoot down all remaining af_iucv sockets on the interface. Now that the offline path always calls dev_close(), the NETDEV_GOING_DOWN event from __dev_close_many() is sufficient and this hack can be removed. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: remove open-coded inet_make_mask() | Julian Wiedmann | 3 | -24/+20 | |
| Use inet_make_mask() to replace some complicated bit-fiddling. Also use the right data types to replace some raw memcpy calls with proper assignments. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: clean up L3 sysfs code | Julian Wiedmann | 2 | -85/+33 | |
| Consolidate some duplicated code for adding RXIP/VIPA addresses, and move the locking to where it's actually needed. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: overhaul L3 IP address dump code | Julian Wiedmann | 3 | -45/+44 | |
| The current code that dumps the RXIP/VIPA/IPATO addresses via sysfs first checks whether the buffer still provides sufficient space to hold another formatted address. But the maximum length of an formatted IPv4 address is 15 characters, not 12. So we underestimate the max required length and if the buffer was previously filled to _just_ the right level, a formatted address can end up being truncated. Revamp these code paths to use the _actually_ required length of the formatted IP address, and while at it suppress a gratuitous newline. Also use scnprintf() to format the output. In case of a truncation, this would allow us to return the number of characters that were actually written. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: wake up all waiters from qeth_irq() | Julian Wiedmann | 2 | -16/+18 | |
| card->wait_q is shared by different users, for different wake-up conditions. qeth_irq() can potentially trigger multiple of these conditions: 1) A change to channel->irq_pending, which qeth_send_control_data() is waiting for. 2) A change to card->state, which qeth_clear_channel() and qeth_halt_channel() are waiting for. As qeth_irq() does only a single wake_up(), we might miss to wake up a second eligible waiter. Luckily all waiters are guarded with a timeout, so this situation should recover on its own eventually. To make things work robustly, add an additional wake_up() for changes to channel->state. And extract a helper that updates channel->irq_pending along with the needed wake_up(). Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-18 | s390/qeth: only handle IRQs while device is online | Julian Wiedmann | 1 | -37/+31 | |
| A qeth device that's offline should not be receiving any IRQs - all pending IOs have been terminated, and we avoid starting any new ones. So rather than immediately registering the IRQ handler when the device is probed, only register it while the device is online. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-12 | netdev: pass the stuck queue to the timeout handler |   Michael S. Tsirkin | 2 | -2/+2 | |
| This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-08 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net |   Linus Torvalds | 6 | -83/+119 | |
| Pull networking fixes from David Miller: 1) More jumbo frame fixes in r8169, from Heiner Kallweit. 2) Fix bpf build in minimal configuration, from Alexei Starovoitov. 3) Use after free in slcan driver, from Jouni Hogander. 4) Flower classifier port ranges don't work properly in the HW offload case, from Yoshiki Komachi. 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin. 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk. 7) Fix flow dissection in dsa TX path, from Alexander Lobakin. 8) Stale syncookie timestampe fixes from Guillaume Nault. [ Did an evil merge to silence a warning introduced by this pull - Linus ] * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits) r8169: fix rtl_hw_jumbo_disable for RTL8168evl net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add() r8169: add missing RX enabling for WoL on RTL8125 vhost/vsock: accept only packets with the right dst_cid net: phy: dp83867: fix hfs boot in rgmii mode net: ethernet: ti: cpsw: fix extra rx interrupt inet: protect against too small mtu values. gre: refetch erspan header from skb->data after pskb_may_pull() pppoe: remove redundant BUG_ON() check in pppoe_pernet tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE() tcp: tighten acceptance of ACKs not matching a child socket tcp: fix rejected syncookies due to stale timestamps lpc_eth: kernel BUG on remove tcp: md5: fix potential overestimation of TCP option space net: sched: allow indirect blocks to bind to clsact in TC net: core: rename indirect block ingress cb function net-sysfs: Call dev_hold always in netdev_queue_add_kobject net: dsa: fix flow dissection on Tx path net/tls: Fix return values to avoid ENOTSUPP net: avoid an indirect call in ____sys_recvmsg() ... | |||||
| 2019-12-05 | s390/qeth: fix dangling IO buffers after halt/clear | Julian Wiedmann | 5 | -46/+67 | |
| The cio layer's intparm logic does not align itself well with how qeth manages cmd IOs. When an active IO gets terminated via halt/clear, the corresponding IRQ's intparm does not reflect the cmd buffer but rather the intparm that was passed to ccw_device_halt() / ccw_device_clear(). This behaviour was recently clarified in commit b91d9e67e50b ("s390/cio: fix intparm documentation"). As a result, qeth_irq() currently doesn't cancel a cmd that was terminated via halt/clear. This primarily causes us to leak card->read_cmd after the qeth device is removed, since our IO path still holds a refcount for this cmd. For qeth this means that we need to keep track of which IO is pending on a device ('active_cmd'), and use this as the intparm when calling halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its cmd buffer. Since we now keep track of the _expected_ intparm, we can also detect any mismatch; this would constitute a bug somewhere in the lower layers. In this case cancel the active cmd - we effectively "lost" the IRQ and should not expect any further notification for this IO. Fixes: 405548959cc7 ("s390/qeth: add support for dynamically allocated cmds") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-05 | s390/qeth: ensure linear access to packet headers | Julian Wiedmann | 1 | -33/+31 | |
| When the RX path builds non-linear skbs, the packet headers can currently spill over into page fragments. Depending on the packet type and what fields we need to access in the headers, this could cause us to go past the end of skb->data. So for non-linear packets, copy precisely the length of the necessary headers ('linear_len') into skb->data. And don't copy more, upper-level protocols will peel whatever additional packet headers they need. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-05 | s390/qeth: guard against runt packets | Julian Wiedmann | 3 | -6/+23 | |
| Depending on a packet's type, the RX path needs to access fields in the packet headers and thus requires a minimum packet length. Enforce this length when building the skb. On the other hand a single runt packet is no reason to drop the whole RX buffer. So just skip it, and continue processing on the next packet. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-03 | Merge tag 's390-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux | Linus Torvalds | 1 | -0/+2 | |
| Pull more s390 updates from Vasily Gorbik: - Make stack unwinder reliable and suitable for livepatching. Add unwinder testing module. - Fixes for CALL_ON_STACK helper used for stack switching. - Fix unwinding from bpf code. - Fix getcpu and remove compat support in vdso code. - Fix address space control registers initialization. - Save KASLR offset for early dumps. - Handle new FILTERED_BY_HYPERVISOR reply code in crypto code. - Minor perf code cleanup and potential memory leak fix. - Add couple of error messages for corner cases during PCI device creation. * tag 's390-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (33 commits) s390: remove compat vdso code s390/livepatch: Implement reliable stack tracing for the consistency model s390/unwind: add stack pointer alignment sanity checks s390/unwind: filter out unreliable bogus %r14 s390/unwind: start unwinding from reliable state s390/test_unwind: add program check context tests s390/test_unwind: add irq context tests s390/test_unwind: print verbose unwinding results s390/test_unwind: add CALL_ON_STACK tests s390: fix register clobbering in CALL_ON_STACK s390/test_unwind: require that unwinding ended successfully s390/unwind: add a test for the internal API s390/unwind: always inline get_stack_pointer s390/pci: add error message on device number limit s390/pci: add error message for UID collision s390/cpum_sf: Check for SDBT and SDB consistency s390/cpum_sf: Use TEAR_REG macro consistantly s390/cpum_sf: Remove unnecessary check for pending SDBs s390/cpum_sf: Replace function name in debug statements s390/kaslr: store KASLR offset for early dumps ... | |||||
| 2019-12-02 | Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi | Linus Torvalds | 12 | -22/+683 | |
| Pull SCSI updates from James Bottomley: "This is mostly update of the usual drivers: aacraid, ufs, zfcp, NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx plus a whole load of minor updates and fixes. The major core changes are Al Viro's reworking of sg's handling of copy to/from user, Ming Lei's removal of the host busy counter to avoid contention in the multiqueue case and Damien Le Moal's fixing of residual tracking across error handling" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits) scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort() scsi: target: core: Fix a pr_debug() argument scsi: iscsi: Don't send data to unbound connection scsi: target: iscsi: Wait for all commands to finish before freeing a session scsi: target: core: Release SPC-2 reservations when closing a session scsi: target: core: Document target_cmd_size_check() scsi: bnx2i: fix potential use after free Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails" scsi: NCR5380: Add disconnect_mask module parameter scsi: NCR5380: Unconditionally clear ICR after do_abort() scsi: NCR5380: Call scsi_set_resid() on command completion scsi: scsi_debug: num_tgts must be >= 0 scsi: lpfc: use hdwq assigned cpu for allocation scsi: arcmsr: fix indentation issues scsi: qla4xxx: fix double free bug scsi: pm80xx: Modified the logic to collect fatal dump scsi: pm80xx: Tie the interrupt name to the module instance scsi: pm80xx: Controller fatal error through sysfs scsi: pm80xx: Do not request 12G sas speeds scsi: pm80xx: Cleanup command when a reset times out ... | |||||
| 2019-12-01 | Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground | Linus Torvalds | 1 | -26/+15 | |
| Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann: "As part of the cleanup of some remaining y2038 issues, I came to fs/compat_ioctl.c, which still has a couple of commands that need support for time64_t. In completely unrelated work, I spent time on cleaning up parts of this file in the past, moving things out into drivers instead. After Al Viro reviewed an earlier version of this series and did a lot more of that cleanup, I decided to try to completely eliminate the rest of it and move it all into drivers. This series incorporates some of Al's work and many patches of my own, but in the end stops short of actually removing the last part, which is the scsi ioctl handlers. I have patches for those as well, but they need more testing or possibly a rewrite" * tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits) scsi: sd: enable compat ioctls for sed-opal pktcdvd: add compat_ioctl handler compat_ioctl: move SG_GET_REQUEST_TABLE handling compat_ioctl: ppp: move simple commands into ppp_generic.c compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic compat_ioctl: unify copy-in of ppp filters tty: handle compat PPP ioctls compat_ioctl: move SIOCOUTQ out of compat_ioctl.c compat_ioctl: handle SIOCOUTQNSD af_unix: add compat_ioctl support compat_ioctl: reimplement SG_IO handling compat_ioctl: move WDIOC handling into wdt drivers fs: compat_ioctl: move FITRIM emulation into file systems gfs2: add compat_ioctl support compat_ioctl: remove unused convert_in_user macro compat_ioctl: remove last RAID handling code compat_ioctl: remove /dev/raw ioctl translation compat_ioctl: remove PCI ioctl translation compat_ioctl: remove joystick ioctl translation ... | |||||
| 2019-11-30 | s390/zcrypt: handle new reply code FILTERED_BY_HYPERVISOR |   Harald Freudenberger | 1 | -0/+2 | |
| This patch introduces support for a new architectured reply code 0x8B indicating that a hypervisor layer (if any) has rejected an ap message. Linux may run as a guest on top of a hypervisor like zVM or KVM. So the crypto hardware seen by the ap bus may be restricted by the hypervisor for example only a subset like only clear key crypto requests may be supported. Other requests will be filtered out - rejected by the hypervisor. The new reply code 0x8B will appear in such cases and needs to get recognized by the ap bus and zcrypt device driver zoo. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> | |||||
| 2019-11-25 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next | Linus Torvalds | 13 | -528/+254 | |
| Pull networking updates from David Miller: "Another merge window, another pull full of stuff: 1) Support alternative names for network devices, from Jiri Pirko. 2) Introduce per-netns netdev notifiers, also from Jiri Pirko. 3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara Larsen. 4) Allow compiling out the TLS TOE code, from Jakub Kicinski. 5) Add several new tracepoints to the kTLS code, also from Jakub. 6) Support set channels ethtool callback in ena driver, from Sameeh Jubran. 7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED, SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long. 8) Add XDP support to mvneta driver, from Lorenzo Bianconi. 9) Lots of netfilter hw offload fixes, cleanups and enhancements, from Pablo Neira Ayuso. 10) PTP support for aquantia chips, from Egor Pomozov. 11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From Josh Hunt. 12) Add smart nagle to tipc, from Jon Maloy. 13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat Duvvuru. 14) Add a flow mask cache to OVS, from Tonghao Zhang. 15) Add XDP support to ice driver, from Maciej Fijalkowski. 16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak. 17) Support UDP GSO offload in atlantic driver, from Igor Russkikh. 18) Support it in stmmac driver too, from Jose Abreu. 19) Support TIPC encryption and auth, from Tuong Lien. 20) Introduce BPF trampolines, from Alexei Starovoitov. 21) Make page_pool API more numa friendly, from Saeed Mahameed. 22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni. 23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy" * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits) libbpf: Fix usage of u32 in userspace code mm: Implement no-MMU variant of vmalloc_user_node_flags slip: Fix use-after-free Read in slip_open net: dsa: sja1105: fix sja1105_parse_rgmii_delays() macvlan: schedule bc_work even if error enetc: add support Credit Based Shaper(CBS) for hardware offload net: phy: add helpers phy_(un)lock_mdio_bus mdio_bus: don't use managed reset-controller ax88179_178a: add ethtool_op_get_ts_info() mlxsw: spectrum_router: Fix use of uninitialized adjacency index mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels bpf: Simplify __bpf_arch_text_poke poke type handling bpf: Introduce BPF_TRACE_x helper for the tracing tests bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT bpf, testing: Add various tail call test cases bpf, x86: Emit patchable direct jump as tail call bpf: Constant map key tracking for prog array pokes bpf: Add poke dependency tracking for prog array maps bpf: Add initial poke descriptor table for jit images bpf: Move owner type, jited info into array auxiliary data ... | |||||
| 2019-11-25 | Merge tag 's390-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux | Linus Torvalds | 13 | -98/+134 | |
| Pull s390 updates from Vasily Gorbik: - Adjust PMU device drivers registration to avoid WARN_ON and few other perf improvements. - Enhance tracing in vfio-ccw. - Few stack unwinder fixes and improvements, convert get_wchan custom stack unwinding to generic api usage. - Fixes for mm helpers issues uncovered with tests validating architecture page table helpers. - Fix noexec bit handling when hardware doesn't support it. - Fix memleak and unsigned value compared with zero bugs in crypto code. Minor code simplification. - Fix crash during kdump with kasan enabled kernel. - Switch bug and alternatives from asm to asm_inline to improve inlining decisions. - Use 'depends on cc-option' for MARCH and TUNE options in Kconfig, add z13s and z14 ZR1 to TUNE descriptions. - Minor head64.S simplification. - Fix physical to logical CPU map for SMT. - Several cleanups in qdio code. - Other minor cleanups and fixes all over the code. * tag 's390-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (41 commits) s390/cpumf: Adjust registration of s390 PMU device drivers s390/smp: fix physical to logical CPU map for SMT s390/early: move access registers setup in C code s390/head64: remove unnecessary vdso_per_cpu_data setup s390/early: move control registers setup in C code s390/kasan: support memcpy_real with TRACE_IRQFLAGS s390/crypto: Fix unsigned variable compared with zero s390/pkey: use memdup_user() to simplify code s390/pkey: fix memory leak within _copy_apqns_from_user() s390/disassembler: don't hide instruction addresses s390/cpum_sf: Assign error value to err variable s390/cpum_sf: Replace function name in debug statements s390/cpum_sf: Use consistant debug print format for sampling s390/unwind: drop unnecessary code around calling ftrace_graph_ret_addr() s390: add error handling to perf_callchain_kernel s390: always inline current_stack_pointer() s390/mm: add mm_pxd_folded() checks to pxd_free() s390/mm: properly clear _PAGE_NOEXEC bit when it is not supported s390/mm: simplify page table helpers for large entries s390/mm: make pmd/pud_bad() report large entries as bad ... | |||||
| 2019-11-25 | Merge tag 'for-5.5/disk-revalidate-20191122' of git://git.kernel.dk/linux-block | Linus Torvalds | 1 | -1/+3 | |
| Pull disk revalidation updates from Jens Axboe: "This continues the work that Jan Kara started to thoroughly cleanup and consolidate how we handle rescans and revalidations" * tag 'for-5.5/disk-revalidate-20191122' of git://git.kernel.dk/linux-block: block: move clearing bd_invalidated into check_disk_size_change block: remove (__)blkdev_reread_part as an exported API block: fix bdev_disk_changed for non-partitioned devices block: move rescan_partitions to fs/block_dev.c block: merge invalidate_partitions into rescan_partitions block: refactor rescan_partitions | |||||
| 2019-11-22 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net |   Jakub Kicinski | 4 | -13/+33 | |
| Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock from commit c8183f548902 ("s390/qeth: fix potential deadlock on workqueue flush"), removed the code which was removed by commit 9897d583b015 ("s390/qeth: consolidate some duplicated HW cmd code"). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> | |||||
| 2019-11-20 | s390/qeth: return proper errno on IO error | Julian Wiedmann | 1 | -5/+5 | |
| When propagating IO errors back to userspace, one error path in qeth_irq() currently returns '1' instead of a proper errno. Fixes: 54daaca7024d ("s390/qeth: cancel cmd on early error") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-20 | s390/qeth: fix potential deadlock on workqueue flush | Julian Wiedmann | 3 | -8/+28 | |
| The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access to its configuration state. This can result in a deadlock when qeth_l2_stop_card() - called under the conf_mutex - blocks on flush_workqueue() to wait for the completion of pending bridgeport workers. Such workers would also need to aquire the conf_mutex, stalling indefinitely. Introduce a lock that specifically guards the bridgeport configuration, so that the workers no longer need the conf_mutex. Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also fixes a theoretical race against a concurrent qeth_bridge_port_role_store() operation. Fixes: c0a2e4d10d93 ("s390/qeth: conclude all event processing before offlining a card") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-15 | net/smc: immediate termination for SMCD link groups |   Ursula Braun | 1 | -2/+0 | |
| SMCD link group termination is called when peer signals its shutdown of its corresponding link group. For regular shutdowns no connections exist anymore. For abnormal shutdowns connections must be killed and their DMBs must be unregistered immediately. That means the SMCR method to delay the link group freeing several seconds does not fit. This patch adds immediate termination of a link group and its SMCD connections and makes sure all SMCD link group related cleanup steps are finished. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: don't check drvdata in sysfs code | Julian Wiedmann | 3 | -199/+4 | |
| Given the way how the sysfs attributes are registered / unregistered, the show/store helpers will never be called with a NULL drvdata. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: replace qeth_l3_get_addr_buffer() | Julian Wiedmann | 2 | -40/+23 | |
| The remaining usage effectively is a kmemdup() of the query object. By not wrapping it, some of the callers can now use GFP_KERNEL for the allocation. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: remove VLAN tracking for L3 devices | Julian Wiedmann | 2 | -32/+11 | |
| Use vlan_for_each() instead of tracking each registered VID internally. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: consolidate L3 mcast registration code | Julian Wiedmann | 1 | -90/+30 | |
| Current code processes each (VLAN) device twice - once to inspect the IPv4 mcast addresses, and then a second time to walk the IPv6 mcast addresses. Unify all this into a single helper, thus removing some checks and a duplicated VLAN lookup. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: remove gratuitious RX modeset | Julian Wiedmann | 1 | -2/+0 | |
| Trust the IPv4/IPv6 code to properly remove its mcast addresses when a VLAN device is unregistered, and then also trigger an RX modeset whenever it's needed. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: fine-tune L3 mcast locking | Julian Wiedmann | 1 | -4/+3 | |
| Push the inet6_dev locking down into the helper that actually needs it for walking the mc_list. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: clean up error path in qeth_core_probe_device() | Julian Wiedmann | 1 | -1/+2 | |
| qeth_core_free_card() is meant to be the counterpart of qeth_alloc_card() - but unfortunately was also picked as the place to free the QDIO queues. This gets messy when qeth_core_probe_device() fails during qeth_add_dbf_entry(). At this point the card->qdio.state is not initialized yet, so qeth_free_qdio_queues() ends up operating on uninitialized data. Luckily for now, the whole qeth_card struct is zero-allocated and the value of the QETH_QDIO_UNINITIALIZED enum is 0 as well. So there's no real impact from this bug at the moment, it's just really fragile. Clean this up by moving the qeth_free_qdio_queues() call up one level in the hierarchy. This way it doesn't get called from the error path. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: handle skb allocation error gracefully | Julian Wiedmann | 1 | -15/+10 | |
| When current code fails to allocate an skb in the RX path, it drops the whole RX buffer. Considering the large number of packets that a single RX buffer might contain, this is quite drastic. Skip over the packet instead, and try to extract the next packet from the RX buffer. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: drop unwanted packets earlier in RX path | Julian Wiedmann | 3 | -41/+44 | |
| Packets with an unexpected HW format are currently first extracted from the RX buffer, passed upwards to the layer-specific driver and only then finally dropped. Enhance the RX path so that we can drop such packets before even allocating an skb. For this, add some additional logic so that when a packet is meant to be dropped, we can still walk along the packet's data chunks in the RX buffer. This allows us to extract the following packet(s) from the buffer. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: support per-frame invalidation | Julian Wiedmann | 3 | -2/+14 | |
| Each RX buffer may contain up to 64KB worth of data. In case the device needs to discard a packet _after_ already having reserved space for it in the buffer, the whole buffer gets set to ERROR state. As the buffer might contain any number of good packets, this can result in collateral packet loss. qeth can provide relief by enabling per-frame invalidation. The RX buffer is then presented as usual, we just need to spot & drop any individual packet that was flagged as invalid. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | s390/qeth: gather more detailed RX dropped/error statistics | Julian Wiedmann | 5 | -8/+20 | |
| Where available, use the fine-grained counters in rtnl_link_stats64 to indicate different RX error causes. For drop reasons, use driver-private ethtool counters. In particular this patch allows us to keep track of driver-side drops due to unknown/unsupported HW descriptor format. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-11-14 | block: remove (__)blkdev_reread_part as an exported API |   Christoph Hellwig | 1 | -1/+3 | |
| In general drivers should never mess with partition tables directly. Unfortunately s390 and loop do for somewhat historic reasons, but they can use bdev_disk_changed directly instead when we export it as they satisfy the sanity checks we have in __blkdev_reread_part. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> [dasd] Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> | |||||
| 2019-11-12 | s390/pkey: use memdup_user() to simplify code |   Markus Elfring | 1 | -24/+4 | |
| Generated by: scripts/coccinelle/api/memdup_user.cocci Link: http://lkml.kernel.org/r/aca044e8-e4b2-eda8-d724-b08772a44ed9@web.de [borntraeger@de.ibm.com: use ==0 instead of <=0 for a size_t variable] [heiko.carstens@de.ibm.com: split bugfix into separate patch; shorten changelog] Signed-off-by: Markus Elfring <Markus.Elfring@web.de> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> | |||||
| 2019-11-12 | s390/pkey: fix memory leak within _copy_apqns_from_user() |   Heiko Carstens | 1 | -1/+3 | |
| Fixes: f2bbc96e7cfad ("s390/pkey: add CCA AES cipher key support") Reported-by: Markus Elfring <Markus.Elfring@web.de> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> | |||||
| 2019-11-12 | Merge tag 'vfio-ccw-20191111' of https://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into features |   Vasily Gorbik | 6 | -14/+93 | |
| enhance tracing in vfio-ccw * tag 'vfio-ccw-20191111' of https://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw: vfio-ccw: Rework the io_fctl trace vfio-ccw: Add a trace for asynchronous requests vfio-ccw: Trace the FSM jumptable vfio-ccw: Refactor how the traces are built Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> | |||||
| 2019-11-02 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net |   David S. Miller | 1 | -2/+1 | |
| The only slightly tricky merge conflict was the netdevsim because the mutex locking fix overlapped a lot of driver reload reorganization. The rest were (relatively) trivial in nature. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: don't cache MAC addresses for multicast IPs | Julian Wiedmann | 3 | -19/+12 | |
| Instead of storing the multicast-mapped MAC address in an IP address object, just calculate the MAC address when actually building a cmd for the IP address. While at it, also clean up some rather verbose copying of IP addresses. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: use helpers for IP address hashing | Julian Wiedmann | 2 | -19/+10 | |
| Replace our custom implementations with the stack's version of IP address hashing. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: don't set card state in qeth_qdio_clear_card() | Julian Wiedmann | 1 | -1/+0 | |
| Any change to the card state should only be driven by qeth_l?_set_online() and qeth_l?_stop_card(). qeth_qdio_clear_card() currently also gets called from (a) qeth_core_shutdown(), where we haven't walked through the whole teardown sequence. So changing the state to DOWN is not accurate. (b) qeth_core_hardsetup_card(), which is only called while the card is still in DOWN state. No change in behaviour here. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: consolidate some duplicated HW cmd code | Julian Wiedmann | 3 | -31/+9 | |
| When setting a device online, both subdrivers have the same code to program the HW trap and Isolation mode. Move that code into a single place. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: keep IRQ disabled until NAPI is really done | Julian Wiedmann | 1 | -3/+3 | |
| When napi_complete_done() returns false, the NAPI instance is still active and we can keep the IRQ disabled a little longer. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: use QDIO_BUFNR() | Julian Wiedmann | 1 | -20/+17 | |
| qdio.h recently gained a new helper macro that handles wrap-around on a QDIO queue, consistently use it across all of qeth. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qeth: use IQD Multi-Write | Julian Wiedmann | 2 | -10/+53 | |
| For IQD devices with Multi-Write support, we can defer the queue-flush further and transmit multiple IO buffers with a single TX doorbell. The same-target restriction still applies. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qdio: implement IQD Multi-Write | Julian Wiedmann | 2 | -16/+16 | |
| This allows IQD drivers to send out multiple SBALs with a single SIGA instruction. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-31 | s390/qdio: move SSQD Sniffer mask definition | Julian Wiedmann | 2 | -3/+1 | |
| Put the Sniffer bit next to all the other CHSC AC2 bits. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> | |||||
 |
index : linux-dev | |
| Linux kernel development work - see feature branches | Jason A. Donenfeld |
| aboutsummaryrefslogtreecommitdiffstats |