| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
From: Ursula Braun <ursula.braun@de.ibm.com>
This patch fixes problems in the ctcm driver identified by
static code analysis:
o remove an unnecessary always true condition in ctcm_unpack_skb
o remove duplicate assignment in ctc_mpc_alloc_channel
o remove an unnecessary always true condition in ctcmpc_send_sweep_resp
o remove duplicate initialization in ctcmpc_unpack_skb
o shorten if condition in mpc_action_go_inop
o remove INOP event if mpc group is undefined in mpc_action_doxid7
Signed-off-by: Joel A. Fowler <fowlerja@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the receive code should tolerate any incoming garbage, it
should be protected against a potential wraparound when manipulating
length values within incoming data.
block_len is unsigned, so a too large subtraction will cause a
wraparound.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid kernel warnings by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid kernel warning by using the correct hard_start_xmit return
code NETDEV_TX_BUSY for skb requeuing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lcs hard_start_xmit routine issued return codes other than
defined for this interface. Now lcs returns only either
NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lcs uses low-level kernel_thread implementation.
All drivers should use <linux/kthread.h> API instead.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the fc_host_port_type as FC_PORTTYPE_NPIV when the subchannel
is running in NPIV mode. This allows to see the correct type with
lsscsi -H -t --list
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
A scheduled work might still be pending, running while the adapter is
in progress to get dequeued from the system. This can lead to an
invalid pointer dereference (Oops). Once the adpater is set online
again, ensure the nameserver environment is initialized to the
appropriate values again.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Ensure the refcounting is correct even if we were not able to
schedule a work. In addition we have to make sure no scheduled
work is pending while we're dequeing the adapter from the
systems environment.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
It will not be necessary to set the erp failed status bit
in case a SCSI device is removed by the SCSI mid layer.
In the case a SCSI device is unavailable for a short time
(15 to 20 seconds) a FCP unit will not get on-line again.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the I/O blocking mechanism in the FC transport class to allow
faster failovers for multipathing:
- Call fc_remote_port_delete early to set the rport to BLOCKED.
- Check the rport status in queuecommand with fc_remote_portchkready
to no longer accept new I/O for this port and fail the I/O with the
appropriate scsi_cmnd result.
- Implement the terminate_rport_io handler to abort all pending I/O
requests
- Return SCSI commands with DID_TRANSPORT_DISRUPTED while erp is
running.
- When updating the remote port status, check for late changes and
update the remote ports status accordingly.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
After an error condition resolved a remote storage port was never
re-opened. The incoming RSCN was not processed accordingly due
to a misinterpreted status flag / return value combination.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The usage of the PCI flag to trigger interrupts is optional. Even
without setting the flag, qdio still receives interrupts to continue
working on the queue. Remove the PCI flag from zfcp, it is not
necessary.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The current number based id ERP logging is replaced by a string
based tag version. The benefit is an easier location of the code in
question and the removal of the lengthy array referencing the
individual messages.
The string (7 bytes) based version does not use more space since those
bytes were "used" anyway due to the alignment of the structure.
The encoding of the 7 byte string is as follows
[0-1] = filename
[2-5] = task/function
[6] = section
Due to the character of this string (fixed length) a string
termination is not required here.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
An adapter close was always performed whether it was required,
(e.g. in an error scenario) or not (e.g. initial open).
This patch is changing the process in only doing an
adapter close when it is required.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The status read response FSF_STATUS_READ_SUB_ERROR_PORT is not
defined in the specs and therefore not valid.
All occurrences are removed from the code.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Issue ELS ADISC requests from workqueue. This allows the link test
request to be sent when the request queue is full due to I/O load for
other remote ports. It also simplifies request queue locking,
zfcp_fsf_send_fcp_command_task is now the only function that has
interrupts disabled from the caller. This is also a prereq for the FC
passthrough support that issues ELS requests from userspace.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When the SCSI midlayer is running error recovery, the low-level error
recovery in zfcp could be running and preventing the SCSI midlayer to
issue error recovery requests. To avoid unnecessary error recovery
escalation, wait for the zfcp erp to finish and retry if necessary.
While reworking the SCSI eh handlers, alsa cleanup the code and
simplify the interface from zfcp_scsi to the fsf layer.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For calls from zfcp erp, scsi_eh and sysfs switch the calls issuing
FSF requests to zfcp_fsf_req_sbal_get to wait for free SBALs.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Only increment the req_id for successfully issued requests. This
avoids some confusion when debugging issued fsf requests.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The lock only needs to protect the softirq context called from qdio
against the userspace context called from sysfs. spin_lock and
spin_lock_bh is enough.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Provide measurement data for the utilisation of the QDIO outbound queue.
The additional value allows to calculate an average queue utilisation
by looking at the deltas per time unit. Needed for capacity planning.
It is up to user space to handle wrap-arounds of the 64 bit value.
The new counter neatly complements the existing counter for queue full
conditions. That is why, both statistics counter have been integrated.
Signed-off-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Use the device pointer in zfcp_unit for tracking if we have a
registered SCSI device. With this approach, the flag
ZFCP_STATUS_UNIT_REGISTERED is only redundant and can be removed.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
PORT_PHYS_CLOSING is only set and cleared, but not actually used
for status checking.
PORT_INVALID_WWPN is set when the GID_PN request does not return
a d_id for a remote port, e.g. when a remote port has been
unplugged. For this case, the d_id is zero. In the erp we can
check the d_id and use the normal escalation procedure that gives
up after three retries and remove the special case.
PORT_NO_WWPN is unused: Each port in the remote port list has a
valid wwpn. The WKA ports are now tracked outside the port
list. Remove the PORT_NO_WWPN flag, since this is no longer set
for any port.
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The SUGGEST_* flags in the SCSI command result have been out of fashion
for a while and we don't actually use them in the error handling.
Remove the remaining occurrences.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
|
|
Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Handle a malformed hardware response which some versions of the
Support Element (SE) may present during SE restart and which otherwise
would result in an endless loop in function sclp_dispatch_evbufs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
|
|
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
bus_id usage crept in again; fix it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
|
|
claw printks are converted to dev_xxx and pr_xxx macros.
Signed-off-by: Andy Richter <richtera@us.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/s390/net/lcs.c: In function 'lcs_new_device':
drivers/s390/net/lcs.c:2179: error: implicit declaration of function 'lcs_set_multicast_list'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
claw convert to net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netiucv convert to net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ctcm convert to net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lcs convert to net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have separate netdev_ops for OSA and HiperSocket/TR.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If CONFIG_DEBUG_FS is disabled debugfs_create_file returns -ENODEV instead
of zero. Since the return value is stored and used at shutdown to remove
existing entries an OOPS may be triggered.
Add a check of the debugfs_create_file return value and in case of an error
set the entry to NULL so it will be ignored at shutdown.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When the connection between host and storage server is lost, the
dasd device driver usually blocks all I/O on affected devices and
waits for them to reappear. In some setups however it would be
better if the I/O is returned as error so that device can be
recovered by some other means, eg. in a raid or multipath setup.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When a DASD device enters or leaves the 'online' state we need to
trigger change events for the respective disk and partitions.
These extra events are needed because when disk and partitions are
first added, udev rules that try to read disk labels or other data
may fail as the disk may not yet be ready.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
CC drivers/s390/char/tape_block.o
In file included from drivers/s390/char/tape_block.c:24:
drivers/s390/char/tape.h:159: warning: 'struct request' declared inside
parameter list
Adding the dependency of CONFIG_BLOCK to CONFIG_S390_TAPE_BLOCK.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
|
|
|
|
qeth_l2, qeth_l3 convert to net_device_ops.
qeth_l3 remove vlan neigh_setup hack since it does not work any longer
with the new net_device_ops.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
|
|
Replace s390_root_dev_register() with root_device_register() etc.
[Includes fix from Cornelia Huck]
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
Joel A. Fowler
Roel Kluin
Ursula Braun
Klaus-Dieter Wacker
Christof Schmitt
Swen Schillig
Martin Petermann
Martin Peschke
Martin K. Petersen
David S. Miller
Heiko Carstens
Peter Oberparleiter
Stefan Weinhuber
Cornelia Huck
Andy Richter
Frank Blaschka
Jan Glauber
Holger Smolinski
Kamalesh Babulal
Linus Torvalds
Coly Li
Mark McLoughlin