Age | Commit message (Collapse) | Author | Files | Lines |
|
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realign a comment after the change introduced by the
previous patch.
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable pie_vars->accu_prob is used as an accumulator for
probability values. Since probabilty values are scaled using the
MAX_PROB macro denoting (2^64 - 1), pie_vars->accu_prob is
likely to overflow as it is of type u64.
The variable pie_vars->accu_prob_overflows counts the number of
times the variable pie_vars->accu_prob overflows.
The MAX_PROB macro needs to be equal to at least (2^39 - 1) in
order to do precise calculations without any underflow. Thus
MAX_PROB can be reduced to (2^56 - 1) without affecting the
precision in calculations drastically. Doing so will eliminate
the need for the variable pie_vars->accu_prob_overflows as the
variable pie_vars->accu_prob will never overflow.
Removing the variable pie_vars->accu_prob_overflows also reduces
the size of the structure pie_vars to exactly 64 bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function pie_calculate_probability(), the variables alpha and
beta are of type u64. The variables qdelay, qdelay_old and
params->target are of type psched_time_t (which is also u64).
The explicit type casting done when calculating the value for
the variable delta is redundant and not required.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove ambiguity by using the term backlog instead of qlen when
representing the queue length in bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the filler functions more generic, use network
relative skb pulling.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When checking the protocol number tcf_ct_flow_table_lookup() handles
the flow as if it's always ipv4, while it can be ipv6.
Instead, refactor the code to fetch the tcp header, if available,
in the relevant family (ipv4/ipv6) filler function, and do the
check on the returned tcp header.
Fixes: 46475bb20f4b ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Core already zeroes out the struct ethtool_coalesce structure,
drivers don't have to set every field to 0 individually.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.
The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.
The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:
- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
Key Length) of each possible key field. The offset of each field is
defined as the sum between the offset and the sum of the previous
field.
- A set of accessors on top of vcap_key_set for shorter (aka less
typing) access to the HKO and HKL of each key field.
Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.
The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a cosmetic patch that makes the name of the driver private
variable be used uniformly in ocelot_ace.c as in the rest of the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to check the "ret" variable, one can just return the
function result back to the caller.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "ocelot_rule" variable name is both annoyingly long trying to
distinguish itself from struct flow_rule *rule =
flow_cls_offload_flow_rule(f), as well as actually different from the
"ace" variable name which is used all over the place in ocelot_ace.c and
is referring to the same structure.
And the "rule" variable name is, confusingly, different from f->rule,
but sometimes one has to look up to the beginning of the function to get
an understanding of what structure type is actually being handled.
So let's use the "ace" name wherever possible ("Access Control Entry").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).
But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.
So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.
This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.
Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.
And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot_ace_rule is port specific now. Make it flexible to
be able to support multiple ports too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rely on ethtool to properly present the fact that FW and bus
are not available for the gianfar driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rely on ethtool to properly present the fact that FW is not
available for the ucc_geth driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rely on ethtool to properly present the fact that FW is not
available for the dpaa driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to set static versions because linux kernel is
released all together with same version applicable to the whole
code base.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use general linux kernel version instead of static driver version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use general linux kernel version instead of static driver version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove driver version in favor of general linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove static driver version from the ethtool output.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert dlink drivers to use linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in assignments of driver version while linux kernel
is released as a monolith where the whole code base is aligned to one
general version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rely on global linux kernel version instead of static value.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use default ethtool version instead of static variant.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to overwrite global linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in static driver version, use global
linux kernel version instead.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to set N/A if FW is not available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean the code related to various versions: driver and module.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to set N/A for the ethtool fields.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Delete driver and module versions in favor of global
linux kernel variant.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Size of LIQUIDIO_PACKAGE is 0 and it means that checks of package
version never worked, delete dead code.
Fixes: 3258124534f6 ("liquidio: Consolidate common functionality")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop driver version in favor of global to linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove driver and module version in favor of default one.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to explicitly set N/A if FW not available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 2 second delay before calling qrtr_ns_init() meant that the remote
processors would register as endpoints in qrtr and the say_hello() call
would therefor broadcast the outgoing HELLO to them. With the HELLO
handshake corrected this delay is no longer needed.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lost in the translation from the user space implementation was the
detail that HELLO mesages must be exchanged between each node pair. As
such the incoming HELLO must be replied to.
Similar to the previous implementation no effort is made to prevent two
Linux boxes from continuously sending HELLO messages back and forth,
this is left to a follow up patch.
say_hello() is moved, to facilitate the new call site.
Fixes: 0c2204a4ad71 ("net: qrtr: Migrate nameservice to kernel from userspace")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of hand-coding the busywait() predicate, use the until_counter_is()
introduced recently.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A function busywait() was recently added based on the logic in
__tc_check_packets(). Convert the code in tc_common to use the new
function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
until_counter_is() currently takes as an argument a number and the
condition holds when the current counter value is >= that number. Make the
function more generic by taking a partial expression instead of just the
number.
Convert the two existing users.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function tc_rule_stats_get() fetches a given statistic of a TC rule
given the rule preference. Another common way to reference a rule is using
its handle. Introduce a dual to the aforementioned function that gets a
statistic given rule handle.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a DATA_FIN is sent in a MPTCP DSS option that contains a data
mapping, the DATA_FIN consumes one byte of space in the mapping. In this
case, the DATA_FIN should only be included in the DSS option if its
sequence number aligns with the end of the mapped data. Otherwise the
subflow can send an incorrect implicit sequence number for the DATA_FIN,
and the DATA_ACK for that sequence number would not close the
MPTCP-level connection correctly.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|