| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch simplifies SRB structure usage in driver.
- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.
Some of the other improvements are as follows
- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
With support for dual mode in the driver, this mode becomes
dead code. Remove reverse_ini_mode from code.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add switch to allow both Initiator Mode & Target
mode to operate at the same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Currently code performs a full scan of the fabric for
every RSCN. Its an expensive process in a noisy large SAN.
This patch optimizes expensive fabric discovery process by
scanning switch for the affected port when RSCN is received.
Currently Initiator Mode code makes login/logout decision without
knowledge of target mode. This causes driver and firmware to go
out-of-sync. This framework synchronizes both initiator mode
personality and target mode personality in making login/logout
decision.
This patch adds following capabilities in the driver
- Send Notification Acknowledgement asynchronously.
- Update session/fcport state asynchronously.
- Create a session or fcport struct asynchronously.
- Send GNL asynchronously. The command will ask FW to
provide a list of FC Port entries FW knows about.
- Send GPDB asynchronously. The command will ask FW to
provide detail data of an FC Port FW knows about or
perform ADISC to verify the state of the session.
- Send GPNID asynchronously. The command will ask switch
to provide WWPN for provided NPort ID.
- Send GPSC asynchronously. The command will ask switch
to provide registered port speed for provided WWPN.
- Send GIDPN asynchronously. The command will ask the
switch to provide Nport ID for provided WWPN.
- In driver unload path, schedule all session for deletion
and wait for deletion to complete before allowing driver
unload to proceed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Current code merges qla_tgt_sess and fc_port structure
into single fc_port structure representing same I-T nexus.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Updated code with d_id from s_id for better readability and
clarity.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: fixed spelling of patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Callback for sp->done expects scsi_qla_host is passed in as argument,
Instead qla_hw_data is passed in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
During initial implementation, tape support was included but not
enabled by default on target. So far, we don't see any target
customer requesting this support. Since this code is not being
used actively, we want to remove it and we will add back if there
are any request in future for SRR support.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Trace flags are useful during debugging crash dumps
using crash utility. These trace flags makes it easier
to understand various states a command has successfully
completed.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Move code code which converts Task Mgmt Command flags for
ATIO to TCM #defines, from qla2xxx driver to tcm_qla2xxx
driver.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds internal LIO sgl limit since the driver already
sets a max transfer limit on transport layer of 1MB to the client.
Cc: stable@vger.kernel.org
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Pull SCSI fix from James Bottomley:
"A single fix this time: a fix for a virtqueue removal bug which only
appears to affect S390, but which results in the queue hanging forever
thus causing the machine to fail shutdown"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: virtio_scsi: Reject commands when virtqueue is broken
|
|
|
|
This patch reverts commit f80de881d8df and avoids that sending a
WRITE SAME command to the iSCSI initiator triggers the following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
TARGET_CORE[iSCSI]: Expected Transfer Length: 260096 does not match SCSI CDB Length: 512 for SAM Opcode: 0x41
IP: iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]
Oops: 0000 [#1] SMP
Modules linked in: target_core_user uio target_core_iblock target_core_file iscsi_target_mod target_core_mod netconsole configfs crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 crypto_simd cryptd glue_helper virtio_console virtio_rng virtio_balloon serio_raw i2c_piix4 acpi_cpufreq button iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ext4 jbd2 mbcache virtio_blk virtio_net psmouse floppy drm_kms_helper syscopyarea
sysfillrect sysimgblt fb_sys_fops ttm drm virtio_pci
CPU: 2 PID: 5 Comm: kworker/u8:0 Not tainted 4.10.0-rc5-debug+ #3
Workqueue: iscsi_q_0 iscsi_xmitworker [libiscsi]
RIP: 0010:iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]
Call Trace:
iscsi_sw_tcp_xmit_segment+0x84/0x120 [iscsi_tcp]
iscsi_sw_tcp_pdu_xmit+0x51/0x180 [iscsi_tcp]
iscsi_tcp_task_xmit+0xb3/0x290 [libiscsi_tcp]
iscsi_xmit_task+0x4e/0xc0 [libiscsi]
iscsi_xmitworker+0x243/0x330 [libiscsi]
process_one_work+0x1d8/0x4b0
worker_thread+0x49/0x4a0
kthread+0x102/0x140
Fixes: f80de881d8df ("sd: remove __data_len hack for WRITE SAME")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jens Axboe <axboe@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
[ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
virtscsi_queuecommand()
-> virtscsi_kick_cmd()
-> virtscsi_add_cmd()
-> virtqueue_add_sgs()
-> virtqueue_add()
if success
return 0
elseif vq->broken or vring_mapping_error()
return -EIO
else
return -ENOSPC
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
[ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
[ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI target fixes from Bart Van Assche:
- two small fixes for the ibmvscsis driver
- ten patches with bug fixes for the target mode of the qla2xxx driver
- four patches that avoid that the "sparse" and "smatch" static
analyzer tools report false positives for the qla2xxx code base
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
qla2xxx: Disable out-of-order processing by default in firmware
qla2xxx: Fix erroneous invalid handle message
qla2xxx: Reduce exess wait during chip reset
qla2xxx: Terminate exchange if corrupted
qla2xxx: Fix crash due to null pointer access
qla2xxx: Collect additional information to debug fw dump
qla2xxx: Reset reserved field in firmware options to 0
qla2xxx: Set tcm_qla2xxx version to automatically track qla2xxx version
qla2xxx: Include ATIO queue in firmware dump when in target mode
qla2xxx: Fix wrong IOCB type assumption
qla2xxx: Avoid that building with W=1 triggers complaints about set-but-not-used variables
qla2xxx: Move two arrays from header files to .c files
qla2xxx: Declare an array with file scope static
qla2xxx: Fix indentation
ibmvscsis: Fix sleeping in interrupt context
ibmvscsis: Fix max transfer length
|
|
Pull SCSI fixes from James Bottomley:
"This is a set of 12 fixes including the mpt3sas one that was causing
hangs on ATA passthrough.
The others are a couple of zoned block device fixes, a SAS device
detection bug which lead to SATA drives not being matched to bays, two
qla2xxx MSI fixes, a qla2xxx req for rsp confusion caused by cut and
paste, and a few other minor fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: fix hang on ata passthrough commands
scsi: lpfc: Set elsiocb contexts to NULL after freeing it
scsi: sd: Ignore zoned field for host-managed devices
scsi: sd: Fix wrong DPOFUA disable in sd_read_cache_type
scsi: bfa: fix wrongly initialized variable in bfad_im_bsg_els_ct_request()
scsi: ses: Fix SAS device detection in enclosure
scsi: libfc: Fix variable name in fc_set_wwpn
scsi: lpfc: avoid double free of resource identifiers
scsi: qla2xxx: remove irq_affinity_notifier
scsi: qla2xxx: fix MSI-X vector affinity
scsi: qla2xxx: Fix apparent cut-n-paste error.
scsi: qla2xxx: Get mutex lock before checking optrom_state
|
|
|
|
mpt3sas has a firmware failure where it can only handle one pass through
ATA command at a time. If another comes in, contrary to the SAT
standard, it will hang until the first one completes (causing long
commands like secure erase to timeout). The original fix was to block
the device when an ATA command came in, but this caused a regression
with
commit 669f044170d8933c3d66d231b69ea97cb8447338
Author: Bart Van Assche <bart.vanassche@sandisk.com>
Date: Tue Nov 22 16:17:13 2016 -0800
scsi: srp_transport: Move queuecommand() wait code to SCSI core
So fix the original fix of the secure erase timeout by properly
returning SAM_STAT_BUSY like the SAT recommends. The original patch
also had a concurrency problem since scsih_qcmd is lockless at that
point (this is fixed by using atomic bitops to set and test the flag).
[mkp: addressed feedback wrt. test_bit and fixed whitespace]
Fixes: 18f6084a989ba1b (mpt3sas: Fix secure erase premature termination)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Out of order(OOO) processing requires initiator, switch
and target to support OOO. In today's environment, none
of the switches support OOO. OOO requires extra buffer
space which affect performance. By turning ON this feature
in QLogic's FW, it delays error recovery because dropped
frame is treated as out of order frame. We're turning OFF
this option of speed up error recovery.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.
Following message is seen in the logs.
"Error entry - invalid handle/queue (ffff)."
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Soft reset and Risc reset should take 100uS to complete.
This change pad the timeout up to 400uS, which should be
plenty.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
During code inspection, while investigating following stack trace
seen on one of the test setup, we found out there was possibility
of memory leak becuase driver was not unwinding the stack properly.
This issue has not been reproduced in a test environment or on a
customer setup.
Here's stack trace that was seen.
[1469877.797315] Call Trace:
[1469877.799940] [<ffffffffa03ab6e9>] qla2x00_mem_alloc+0xb09/0x10c0 [qla2xxx]
[1469877.806980] [<ffffffffa03ac50a>] qla2x00_probe_one+0x86a/0x1b50 [qla2xxx]
[1469877.814013] [<ffffffff813b6d01>] ? __pm_runtime_resume+0x51/0xa0
[1469877.820265] [<ffffffff8157c1f5>] ? _raw_spin_lock_irqsave+0x25/0x90
[1469877.826776] [<ffffffff8157cd2d>] ? _raw_spin_unlock_irqrestore+0x6d/0x80
[1469877.833720] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.839885] [<ffffffff8157cd0c>] ? _raw_spin_unlock_irqrestore+0x4c/0x80
[1469877.846830] [<ffffffff81319b9c>] local_pci_probe+0x4c/0xb0
[1469877.852562] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.858727] [<ffffffff81319c89>] pci_call_probe+0x89/0xb0
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
During NVRAM initialization in target mode, reset reserved
fields in firmware options to Zero (BIT 15)
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Include ATIO queue for ISP27XX when firmware dump is collected
for target mode.
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
qlt_reset is called with Immedidate Notify IOCB only.
Current code wrongly cast it as ATIO IOCB.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Remove two set-but-not-used variables and avoid that the compiler
warns about a third variable (rc).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that building with W=1 triggers compiler
warnings similar to the following:
drivers/scsi/qla2xxx/qla_nx2.h:538:23: warning: ‘qla8044_reg_tbl’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that building with W=1 triggers a compiler warning
about a missing declaration.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
|
|
This patch avoids that smatch complains about inconsistent indentation.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Christoph Hellwig <hch@lst.de>
|
|
Set the elsiocb contexts to NULL after freeing as others depend on it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no good match of the zoned field of the block device
characteristics page for host-managed devices. For these devices, the
zoning model is derived directly from the device type. So ignore the
zoned field for these drives.
[mkp: typo]
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Zoned block devices force the use of READ/WRITE(16) commands by setting
sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in
DPOFUA always being disabled for these drives as the assumed use of
the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw.
Strenghten the test by also checking that sdkp->use_16_for_rw is false.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 01e0e15c8b3b ("scsi: don't use fc_bsg_job::request and
fc_bsg_job::reply directly") introduced a typo, which causes that the
bsg_request variable in bfad_im_bsg_els_ct_request() is initialized to
itself instead of pointing to the bsg job's request.
Reported-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The call to scsi_is_sas_rphy() needs to be made on the SAS end_device,
not on the SCSI device.
Fixes: 835831c57e9b ("ses: use scsi_is_sas_rphy instead of is_sas_attached")
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, dma_alloc_coherent is being called with a GFP_KERNEL
flag which allows it to sleep in an interrupt context, need to
change to GFP_ATOMIC.
Cc: stable@vger.kernel.org
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Reviewed-by: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Current code incorrectly calculates the max transfer length, since
it is assuming a 4k page table, but ppc64 all run on 64k page tables.
Cc: stable@vger.kernel.org
Reported-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
|
|
Pull block fixes from Jens Axboe:
- the virtio_blk stack DMA corruption fix from Christoph, fixing and
issue with VMAP stacks.
- O_DIRECT blkbits calculation fix from Chandan.
- discard regression fix from Christoph.
- queue init error handling fixes for nbd and virtio_blk, from Omar and
Jeff.
- two small nvme fixes, from Christoph and Guilherme.
- rename of blk_queue_zone_size and bdev_zone_size to _sectors instead,
to more closely follow what we do in other places in the block layer.
This interface is new for this series, so let's get the naming right
before releasing a kernel with this feature. From Damien.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't try to discard from __blkdev_issue_zeroout
sd: remove __data_len hack for WRITE SAME
nvme: use blk_rq_payload_bytes
scsi: use blk_rq_payload_bytes
block: add blk_rq_payload_bytes
block: Rename blk_queue_zone_size and bdev_zone_size
nvme: apply DELAY_BEFORE_CHK_RDY quirk at probe time too
nvme-rdma: fix nvme_rdma_queue_is_ready
virtio_blk: fix panic in initialization error path
nbd: blk_mq_init_queue returns an error code on failure, not NULL
virtio_blk: avoid DMA to stack for the sense buffer
do_direct_IO: Use inode->i_blkbits to compute block count to be cleaned
|
|
Now that we have the blk_rq_payload_bytes helper available to determine
the actual I/O size we don't need to mess around with __data_len for
WRITE SAME.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Without that we'll pass a wrong payload size in cmd->sdb, which
can lead to hangs with drivers that need the total transfer size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Chris Valean <v-chvale@microsoft.com>
Reported-by: Dexuan Cui <decui@microsoft.com>
Fixes: f9d03f96 ("block: improve handling of the magic discard payload")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Pull SCSI fixes from James Bottomley:
"The major fix is the bfa firmware, since the latest 10Gb cards fail
probing with the current firmware.
The rest is a set of minor fixes: one missed Kconfig dependency
causing randconfig failures, a missed error return on an error leg, a
change for how multiqueue waits on a blocked device and a don't reset
while in reset fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: bfa: Increase requested firmware version to 3.2.5.1
scsi: snic: Return error code on memory allocation failure
scsi: fnic: Avoid sending reset to firmware when another reset is in progress
scsi: qedi: fix build, depends on UIO
scsi: scsi-mq: Wait for .queue_rq() if necessary
|
|
|
|
Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.
Signed-off-by: Roberto Sassu <rsassu@suse.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that qla2xxx uses the IRQ layer affinity assignment, affinity won't
change over the life time of a device and the notifiers are useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The first two or three vectors in qla2xxx adapter are global and not
associated with a specific queue. They should not have IRQ affinity
assigned.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
Joe Carnuccio
Quinn Tran
Himanshu Madhani
Bryant G. Ly
Linus Torvalds
James Bottomley
Bart Van Assche
Eric Farman
Johannes Thumshirn
Damien Le Moal
Ewan D. Milne
Christoph Hellwig
Roberto Sassu