| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The old DAC960 driver was fine with merging over segment boundaries, so
this new driver should be too.
[mkp: typos]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The old DAC960 driver was fine with merging over segment boundaries, so
this new driver should be too.
[mkp: typos]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Although MegaRAID controllers support 64-bit DMA addressing, as per
hardware design, DMA address with all 64-bits set
(0xFFFFFFFF-FFFFFFFF) results in a firmware fault.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Due to hardware errata in Aero controllers, reads to certain fusion
registers could intermittently return zero. This behavior is
transient in nature and subsequent reads will return valid value.
For Aero controllers, any calls to readl to read from certain
registers will be retried for maximum three times, if read returns
zero.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of the register address, pass the instance pointer to clear_intr
and read_fw_status_reg functions. This is done in preparation for adding
adapter type based checks in these functions in later patches of this
series.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Identify all Aero controller PCI IDs with new adapter type.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation for the new Aero series adapter type, all the places where
we check adapter type for Ventura series needs to include any later adapter
types.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
With commit 09c2f95ad404 ("scsi: mpt3sas: Swap I/O memory read value back
to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use
__raw_writeq() instad of writeq().
This introduced a bug apparent on powerpc64 systems such as the Raptor
Talos II that causes the HBA to drop from the PCIe bus under heavy load and
being reinitialized after a couple of seconds.
It can easily be triggered on affacted systems by using something like
fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs
raid6 using LSI 9300-8i and 9400-8i controllers.
The fix consists in resembling the write ordering of writeq() by adding a
mandatory write memory barrier before device access and a compiler barrier
afterwards. The additional MMIO barrier is superfluous.
Signed-off-by: Stephan Günther <moepi@moepi.net>
Reported-by: Matt Corallo <linux@bluematt.me>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The intent of invoking configfs_depend_item in commit 7474f52a82d51
("tcm_qla2xxx: Perform configfs depend/undepend for base_tpg")
was to prevent a physical Fibre Channel port removal when
virtual (NPIV) ports announced through that physical port are active.
The change does not work as expected: it makes enabled physical port
dependent on target configfs subsystem (the port's parent), something
the configfs guarantees anyway.
Besides, scheduling work in a worker thread and waiting for the work's
completion is not really a valid workaround for the requirement not to call
configfs_depend_item from a configfs callback: the call occasionally
deadlocks.
Thus, removing configfs_depend_item calls does not break anything and fixes
the deadlock problem.
Signed-off-by: Anatoliy Glagolev <glagolig@gmail.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For v3 hw, we support DIF operation for SAS, but not SATA.
In addition, DIF CRC16 is supported.
This patchset adds the SW support for the described features. The main
components are as follows:
- Get protection mask from module param
- Fill PI fields
- Fill related to DIF in DQ and protection iu memories
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value. In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.
Fixes: 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The same effects can be achieved by setting the dma_boundary to
PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those
settings into the drivers. Note that in many cases the setting might
be bogus, but this keeps the status quo.
[mkp: fix myrs and myrb]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mac53c94 has no limitations on crossing pages for segments. Just make
the 65535 byte segment size limit explicit, even if it matches the
current block layer limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mesh has no limitations on crossing pages for segments. Just make
the 65535 byte segment size limit explicit, even if it matches the
current block layer limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no such limitation in the protocol or implementation, so
remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This driver already sets the dma_boundary to PAGE_SIZE - 1, which
has the same result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This driver already sets the dma_boundary to PAGE_SIZE - 1, which
has the same result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This allows the host driver to indicate the maximum supported
segment size in a nice an easy way, so that the driver doesn't
have to worry about DMA-layer imposed limitations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A few drivers were not setting the use_clustering flag at all and thus
default to disable. Fix them up to explicitly set this field in
preparation for additional cleanups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit b5b6e8c8d3b4 ("scsi: virtio_scsi: fix IO hang caused by automatic
irq vector affinity") removed all virtio_scsi hostdata users. Since the
SCSI host data is no longer used, also remove the host data itself.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI fixes from James Bottomley:
"Three fixes: The t10-pi one is a regression from the 4.19 release, the
qla2xxx one is a 4.20 merge window regression and the bnx2fc is a very
old bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: t10-pi: Return correct ref tag when queue has no integrity profile
scsi: bnx2fc: Fix NULL dereference in error handling
Revert "scsi: qla2xxx: Fix NVMe Target discovery"
|
|
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version from 27.100.00.00 to 27.101.00.00.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use ioc->base_readl to restrict the readl retries to only Aero controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sometimes Aero controllers appears to be returning bad data (0) for
doorbell register read and if retries are performed immediately after the
bad read, they return good data.
Workaround is added to retry read from doorbell registers for maximum three
times if driver get the zero. Added functions base_readl_aero for Aero IOC
and base_readl for gen35 and other controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Adding flag "is_aero_ioc" to differentiate aero based controllers from
other gen35 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Sht->sg_tablesize is set in the driver, and it will be assigned to
shost->sg_tablesize in SCSI mid-layer. So it is not necessary to assign
shost->sg_table one more time in the driver.
In addition to the change, change each scsi_host_template.sg_tablesize
to HISI_SAS_SGE_PAGE_CNT instead of SG_ALL.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Relocate the codes related to dma_map/unmap in hisi_sas_task_prep() to
reduce complexity, with a view to add DIF/DIX support.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patchset fixes some warnings detected by the sparse tool, like these:
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1469:52: got restricted __le16 [usertype] <noident>
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: warning: incorrect type in assignment (different base types)
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: expected unsigned short [unsigned] [assigned] [usertype] tag_of_task_to_be_managed
drivers/scsi/hisi_sas/hisi_sas_main.c:1723:52: got restricted __le16 [usertype] <noident>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes NVMe discovery by setting SKIP_PRLI flag, so that PRLI is
driven by driver and is retried when the NPIV port is detected to have NVMe
capability.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes issues with NPIV port with FC-NVMe. Clean up code for
remoteport delete and also call nvme_delete when deleting VPs.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Anil Gurumurthy <agurumurthy@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The event_wait semaphore has completion semantics, so we can
change it over to the completion interface for clarity without
changing the behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The wait_sem member is used like a completion, so we should
use the respective API. The behavior is unchanged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 287aba2592870fa5b76134b28173b77f1f7a4492.
We killed the bad firmware and this mod is no longer necessary.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When boxes are run near (or to) OOM, we have a problem with the discard
page allocation in sd. If we fail allocating the special page, we return
busy, and it'll get retried. But since ordering is honored for dispatch
requests, we can keep retrying this same IO and failing. Behind that IO
could be requests that want to free memory, but they never get the
chance. This means you get repeated spews of traces like this:
[1201401.625972] Call Trace:
[1201401.631748] dump_stack+0x4d/0x65
[1201401.639445] warn_alloc+0xec/0x190
[1201401.647335] __alloc_pages_slowpath+0xe84/0xf30
[1201401.657722] ? get_page_from_freelist+0x11b/0xb10
[1201401.668475] ? __alloc_pages_slowpath+0x2e/0xf30
[1201401.679054] __alloc_pages_nodemask+0x1f9/0x210
[1201401.689424] alloc_pages_current+0x8c/0x110
[1201401.699025] sd_setup_write_same16_cmnd+0x51/0x150
[1201401.709987] sd_init_command+0x49c/0xb70
[1201401.719029] scsi_setup_cmnd+0x9c/0x160
[1201401.727877] scsi_queue_rq+0x4d9/0x610
[1201401.736535] blk_mq_dispatch_rq_list+0x19a/0x360
[1201401.747113] blk_mq_sched_dispatch_requests+0xff/0x190
[1201401.758844] __blk_mq_run_hw_queue+0x95/0xa0
[1201401.768653] blk_mq_run_work_fn+0x2c/0x30
[1201401.777886] process_one_work+0x14b/0x400
[1201401.787119] worker_thread+0x4b/0x470
[1201401.795586] kthread+0x110/0x150
[1201401.803089] ? rescuer_thread+0x320/0x320
[1201401.812322] ? kthread_park+0x90/0x90
[1201401.820787] ? do_syscall_64+0x53/0x150
[1201401.829635] ret_from_fork+0x29/0x40
Ensure that the discard page allocation has a mempool backing, so we
know we can make progress.
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull in v4.20-rc6 to resolve the conflict in NVMe, but also to get the
two corruption fixes. We're going to be overhauling the direct dispatch
path, and we need to do that on top of the changes we made for that
in mainline.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Update the driver version to 12.0.0.9
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.
Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On driver termination, after the driver stops fw logging by writing a
register on the chip, the driver immediately unmaps and frees the logging
buffer, without confirming in any way that the chip has received the write
and terminated the logging. As termination on the chip is not immediate,
the chip may issue a dma request to the now unmapped dma buffer, resulting
in a iommu fault.
Change the driver to receive a confirmation that logging ahs been
terminated. As the driver always issues an SLI reset with the device as
part of shutdown, and as part of that is receiving confirmation that the
reset is complete - the driver was modified to perform the write to disable
fw logging prior to the SLI reset and only free the fw log buffer after the
SLI reset is complete. That guarantees use of the fw log buffer is fully
terminated when it is unmapped.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.
Add the chip classifications to the topology checks in the driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid). The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.
Remove the setting of WQID in the ABORT WQE.
Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current discovery state machine the driver treated FLOGI oddly. When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI. The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.
Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).
Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In some link initialization sequences, the fw generates an erroneous FLOGI
payload to the driver without an intervening link bounce. The driver, when
it sees a 2nd FLOGI without an intervening link bounce, automatically
performs a link bounce. In this, the link bounce causes the situate to
repeat and in a nasty loop of link bounces.
Resolve the issue by validating the FLOGI payload. The erroneous FLOGI will
contain VVL signatures that are not normal. When the driver sees these, it
will simply reject the flogi rather than bouncing the link. The reject is
consumed within the firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Two initiator ports were cable swapped and after swap both went down. The
driver internally swaps the nlp nodes based on matching node wwn's but not
the same nport id as before. After detecting a change in the nodes RPI, the
driver sends an UNREG_RPI command and clears the NLP_RPI_REGISTERED flag,
then swaps the node information with the other node. But the other node's
NLP_RPI_REGISTERED flag is also cleared, but it is done so without an
UNREG_RPI being sent, which causes the later REG_RPI for that other node to
fail as the hardware believes its still registered.
Additionally, if the node swap occurred while the two nodes had PLOGI's in
flight, the fc4_types weren't properly getting swapped such that when the
PLOGIs commpleted and PRLI's were then sent, the PRLI's acted on bad
protocol types so the PRLI was for the wrong protocol. NVME devices saw
SCSI FCP PRLIs and vice versa.
Clean up the node swap so that the NLP_RPI_REGISTERED flag is handled
properly.
Fix the handling of the fc4_types when the nodes are swapped as well
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
Christoph Hellwig
Shivasharan S
Stephan Günther
Anatoliy Glagolev
Xiang Chen
Ewan D. Milne
Bart Van Assche
Linus Torvalds
YueHaibing
Suganath Prabu
John Garry
Himanshu Madhani
Giridhar Malavali
Anil Gurumurthy
Arnd Bergmann
James Smart
Martin K. Petersen
Jens Axboe
David S. Miller