| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver currently sets PhysicalPort field to 0xFF for SMPPassthrough
Request message. In zoning topologies this SMPPassthrough command always
operates on devices in one zone (default zone) even when user issues SMP
command for other zone drives.
Define _transport_get_port_id_by_rphy() and
_transport_get_port_id_by_sas_phy() helper functions to get Physical Port
number from sas_rphy & sas_phy respectively for SMPPassthrough request
message so that SMP Passthrough request message is sent to intended zone
device.
Link: https://lore.kernel.org/r/20201027130847.9962-10-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During host reset there is a chance that the Port number allocated by the
firmware for the attached devices may change. Also, it may be possible that
some HBA phy's can go down/come up after reset. As a result, the driver
can't just trust the HBA Port table that it has populated before host reset
as valid. Instead it has to update the HBA Port table in such a way that it
shouldn't disturb the drives which are still accessible even after host
reset.
Use the following algorithm to update the HBA Port table during host reset:
I. After host reset operation and before marking the devices as
responding/non-responding, create a temporary Port table called "New
Port table" by parsing each of the HBA phy's Phy data info read from SAS
IOUnit Page0:
a. Check whether Phy's negotiated link rate is greater than 1.5Gbps, if
not go to next Phy;
b. Get the SAS Address of the attached device;
c. Create a new entry in the "New Port table" with SAS Address field
filled with attached device's SAS Address, port number with Phy's
Port number (read from SAS IOUnit Page0) and enable bit in the 'Phy
mask' field corresponding to current Phy number. New entry is
created only if the driver can't find an entry in the "New Port
table" which matches with attached device 'SAS Address' & 'Port
Number'. If it finds an entry with matches with attached device 'SAS
Address' & 'Port Number' then the driver takes that matched entry and
will enable current Phy number bit in the 'Phy mask' field;
d. After parsing all the HBA phy's info, the driver will have complete
Port table info in "New Port table".
II. Mark all the existing sas_device & sas_expander device structures as
'dirty'.
III. Mark each entry of the HBA Port lists as 'dirty'.
IV. Take each entry from 'New Port table' one by one and check whether the
entry has any corresponding matched entry (which is marked as 'dirty')
in the HBA Port table or not. While looking for a corresponding
matched entry, look for matched entry in the sequence from top row to
bottom row listed in the following table. If you find any matched entry
(according to any of the rules tabulated below) then perform the action
mentioned in the 'Action' column in that matched rule.
===========================================================================
|Search |SAS | Phy Mask | Port | Possibilities| Action |
|every |Address | or | Number | | required |
|entry |matched?| subset of| matched?| | |
|in below| | phy mask | | | |
|sequence| | matched? | | | |
===========================================================================
| 1 |matched | matched | matched | nothing |* unmark HBA port |
| | | | | changed |table entry as |
| | | | | |dirty |
---------------------------------------------------------------------------
| 2 |matched | matched | not | port number |* Update port |
| | | | matched | is changed |number in the |
| | | | | |matched port table |
| | | | | |entry |
| | | | | |* unmask HBA port |
| | | | | |table entry as |
| | | | | |dirty |
---------------------------------------------------------------------------
| 3.a |matched | subset of| matched |some phys |* Add these new |
| | | phy mask | (or) |might have |phys to current |
| | | matched | not |enabled which |port in STL |
| | | | matched |are previously|* Update phy mask |
| | | | (but |disabled |field in HBA's port|
| | | | first | |table's matched |
| | | | look for| |entry, |
| | | | matched | |* Update port |
| | | | one) | |number in the |
| | | | | |matched port |
| | | | | |table entry (if |
| | | | | |port number is |
| | | | | |changed), |
| | | | | |* Unmask HBA port |
| | | | | |table entry as |
| | | | | |dirty |
---------------------------------------------------------------------------
| 3.b |matched | subset of| matched |some phys |*Remove these phys |
| | | phy mask | (or) |might have |from current port |
| | | matched | not |disabled which|in STL |
| | | | matched |are previously|* Update phy mask |
| | | | (but |enabled |field in HBA's port|
| | | | first | |tables's matched |
| | | | look for| |entry, |
| | | | matched | |*Update port number|
| | | | one) | |in the matched port|
| | | | | |table entry (if |
| | | | | |port number is |
| | | | | |changed), |
| | | | | |* Unmask HBA port |
| | | | | |table entry as |
| | | | | |dirty |
---------------------------------------------------------------------------
| 4 |matched | not | matched |A cable |*Remove old phys & |
| | | matched | (or) |attached to an|new phys to current|
| | | | not |expander is |port in STL |
| | | | matched |changed to |* Update phy mask |
| | | | |another HBA |field in HBA's port|
| | | | |port during |tables's matched |
| | | | |reset |entry, |
| | | | | |*Update port number|
| | | | | |in the matched port|
| | | | | |table entry (if |
| | | | | |port number is |
| | | | | |changed), |
| | | | | |* Unmask HBA port |
| | | | | |table entry as |
| | | | | |dirty |
---------------------------------------------------------------------------
V. Delete the hba_port objects which are still marked as dirty.
Link: https://lore.kernel.org/r/20201027130847.9962-9-sreekanth.reddy@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the following scsi_host_template and sas_function_template callback
functions the driver does not have PhysicalPort number information to
retrieve the sas_device object using SAS Address & PhysicalPort number. In
these callback functions the device's rphy object is used to retrieve
sas_device object for the device.
.target_alloc,
.get_enclosure_identifier
.get_bay_identifier
When a rphy (of type sas_rphy) object is allocated then its address is
saved in corresponding sas_device object's rphy field. In
__mpt3sas_get_sdev_by_rphy(), the driver loops over all the sas_device
objects from sas_device_list list to retrieve the sas_device objects whose
rphy matches the provided rphy.
Link: https://lore.kernel.org/r/20201027130847.9962-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Renamed _transport_add_phy_to_an_existing_port() to
mpt3sas_transport_add_phy_to_an_existing_port() and
_transport_del_phy_from_an_existing_port() to
mpt3sas_transport_del_phy_from_an_existing_port() as the driver needs to
call these functions from outside mpt3sas_transport.c file.
Added extra function argument 'port' of type struct hba_port to above
functions and check for portID before adding/removing the phy from the
_sas_port object. I.e. add/remove the phy from _sas_port object only if
_sas_port's port object and phy's port object are the same.
Link: https://lore.kernel.org/r/20201027130847.9962-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently driver retrieves the sas_device/sas_expander objects from
corresponding object's lists using just device's SAS Address.
Make driver retrieve the objects from the corresponding objects list using
device's SAS Address and PhysicalPort (or PortID) number. PhysicalPort
number is the port number of the HBA through which this device is accessed.
Link: https://lore.kernel.org/r/20201027130847.9962-6-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update hba_port's sas_address & phy_mask fields whenever a direct expander
or sas/sata target devices are added or removed.
When any direct attached device is discovered then driver:
- Gets the hba_port object corresponding to device's PhysicalPort
number;
- Updates the hba_port's sas_address field with device's SAS
Address;
- Updates the hba_port's phy_mask filed with device's narrow/wide
port Phy number bits;
- If a sas/sata end device (not only direct-attached devices) is added
then corresponding sas_device object's port variable is assigned with
hba_port object's address whose port_id matches the device's
PhysicalPort number.
- If an expander device is added then corresponding sas_expander object's
port variable is assigned with hba_port object's address whose port_id
matches the expander device's PhysicalPort number.
When any direct attached device is detached then driver will delete the
hba_port object corresponding to device's PhysicalPort number.
Whenever any HBA phy's link (of direct attached device's port) comes up
then update the phy_mask field of corresponding hba_port object.
Link: https://lore.kernel.org/r/20201027130847.9962-5-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rearrange _scsih_mark_responding_sas_device function. No functional change.
Link: https://lore.kernel.org/r/20201027130847.9962-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allocate hba_port object whenever a new HBA's wide/narrow port is
identified while processing the SASIOUnitPage0's phy data and add this
object to port_table_list. Deallocate these objects during driver unload.
Link: https://lore.kernel.org/r/20201027130847.9962-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Define a new hba_port structure which holds the following variables:
- port_id: Port ID of the narrow/wide port of the HBA
- sas_address: SAS Address of the remote device that is attached to the
current HBA port
- phy_mask: HBA's phy bits to which above SAS addressed device is attached
- flags: This field is used to refresh port details during HBA reset
Link: https://lore.kernel.org/r/20201027130847.9962-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While reenabling the IRQ after irq poll there may be small time window
where HBA firmware has posted some replies and raise the interrupts but
driver has not received the interrupts. So we may observe I/O timeouts as
the driver has not processed the replies as interrupts got missed while
reenabling the IRQ.
To fix this issue the driver has to go for one more round of processing the
reply descriptors from reply descriptor post queue after enabling the IRQ.
Link: https://lore.kernel.org/r/20201102072746.27410-1-sreekanth.reddy@broadcom.com
Reported-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
alua_bus_detach() might be running concurrently with alua_rtpg_work(), so
we might trip over h->sdev == NULL and call BUG_ON(). The correct way of
handling it is to not set h->sdev to NULL in alua_bus_detach(), and call
rcu_synchronize() before the final delete to ensure that all concurrent
threads have left the critical section. Then we can get rid of the
BUG_ON() and replace it with a simple if condition.
Link: https://lore.kernel.org/r/1600167537-12509-1-git-send-email-jitendra.khasdev@oracle.com
Link: https://lore.kernel.org/r/20200924104559.26753-1-hare@suse.de
Cc: Brian Bunker <brian@purestorage.com>
Acked-by: Brian Bunker <brian@purestorage.com>
Tested-by: Jitendra Khasdev <jitendra.khasdev@oracle.com>
Reviewed-by: Jitendra Khasdev <jitendra.khasdev@oracle.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI fixes from James Bottomley:
"Four driver fixes and one core fix.
The core fix closes a race window where we could kick off a second
asynchronous scan because the test and set of the variable preventing
it isn't atomic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hisi_sas: Stop using queue #0 always for v2 hw
scsi: ibmvscsi: Fix potential race after loss of transport
scsi: mptfusion: Fix null pointer dereferences in mptscsih_remove()
scsi: qla2xxx: Return EBUSY on fcport deletion
scsi: core: Don't start concurrent async scan on same host
|
|
Ensure getting a free ccb is done under the spin_lock.
Link: https://lore.kernel.org/r/f3ec374cada762149911ff35e92a68a15a7d0327.camel@areca.com.tw
Signed-off-by: ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow configuring the default command timeout value for devices attached to
arcmsr controllers.
Link: https://lore.kernel.org/r/27c0cda7fd103f05021adaf67490e9298ed5cc3f.camel@areca.com.tw
Signed-off-by: ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Enabling this capability to let HBA power-collapse more often to save
power.
Link: https://lore.kernel.org/r/1306284ab2215425ca0a3d9c802574cbd6d35ea7.1603825776.git.asutoshd@codeaurora.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During clock gating, after clocks are disabled, put HBA into LPM to save
more power.
Link: https://lore.kernel.org/r/52198e70bff750632740d78678a815256d697e43.1603825776.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When hpsa_scsi_add_host() fails, h->lastlogicals is leaked since it is
missing a free() in the error handler.
Fix this by adding free() when hpsa_scsi_add_host() fails.
Link: https://lore.kernel.org/r/20201027073125.14229-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
gcc -Wextra points out an assignment between two different enum types:
drivers/scsi/libfc/fc_exch.c: In function 'fc_exch_setup_hdr':
../drivers/scsi/libfc/fc_exch.c:275:26: warning: implicit conversion from 'enum fc_class' to 'enum fc_sof' [-Wenum-conversion]
This seems to be intentional, as the same numeric values are used here, so
shut up the warning by adding an explicit cast.
Link: https://lore.kernel.org/r/20201026214911.3892701-1-arnd@kernel.org
Fixes: 42e9a92fe6a9 ("[SCSI] libfc: A modular Fibre Channel library")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Building libfc with gcc -Warray-bounds identifies a number of cases in one
file where a strncpy() is performed into a single-byte character array:
In file included from include/linux/bitmap.h:9,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/spinlock.h:59,
from include/linux/debugobjects.h:6,
from include/linux/timer.h:8,
from include/scsi/libfc.h:11,
from drivers/scsi/libfc/fc_elsct.c:17:
In function 'strncpy',
inlined from 'fc_ct_ms_fill.constprop' at drivers/scsi/libfc/fc_encode.h:235:3:
include/linux/string.h:290:30: warning: '__builtin_strncpy' offset [56, 135] from the object at 'pp' is out of the bounds of referenced subobject 'value' with type '__u8[1]' {aka 'unsigned char[1]'} at offset 56 [-Warray-bounds]
290 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:300:9: note: in expansion of macro '__underlying_strncpy'
300 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
This is not a bug because the 1-byte array is used as an odd way to express
a variable-length data field here. I tried to convert it to a
flexible-array member, but in the end could not figure out why the
sizeof(struct fc_fdmi_???) are used the way they are, and how to properly
convert those.
Work around this instead by abstracting the string copy in a slightly
higher-level function fc_ct_hdr_fill() helper that strscpy() and memset()
to achieve the same result as strncpy() but does not require a
zero-terminated input and does not get checked for the array overflow
because gcc (so far) does not understand the behavior of strscpy().
Link: https://lore.kernel.org/r/20201026160705.3706396-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most of this file is only used inside of libfc, so move it to where it is
actually used, with only fc_fill_fc_hdr() left inside of the header.
Link: https://lore.kernel.org/r/20201026160705.3706396-1-arnd@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some identifiers have different names between their prototypes
and the kernel-doc markup.
[mkp: fix whitespace]
Link: https://lore.kernel.org/r/8ed7f149f25a363eea76e514c253c4e337c59379.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update lpfc version to 12.8.0.5
Link: https://lore.kernel.org/r/20201020202719.54726-10-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that MIB support was registered with FDMI, the driver may receive CT
requests for MIB-related commands. At this time, no command is
supported. However, the driver needs to be graceful and reject the CT
request.
This patch adds identification of the requests as well as sending the
reject response.
Link: https://lore.kernel.org/r/20201020202719.54726-9-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Created new attribute lpfc_enable_mi, which by default is enabled.
Add command definition bits for SLI-4 parameters that recognize whether the
adapter has MIB information support and what revision of MIB data. Using
the adapter information, register vendor-specific MIB support with FDMI.
The registration will be done every link up.
During FDMI registration, encountered a couple of errors when reverting to
FDMI rev1. Code needed to exist once reverting. Fixed these.
Link: https://lore.kernel.org/r/20201020202719.54726-8-james.smart@broadcom.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver supports arbitrarily large scatter-gather lists and the current
value for max_sectors is limiting.
Change max_sectors to the largest value. This was actually done prior but
it only corrected one template and that template was later removed.
So change the remaining 2 templates. Other areas which hard-set the sectors
value should be inheriting what is in the template.
Link: https://lore.kernel.org/r/20201020202719.54726-7-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During code reviews duplicate code sections were found to determine the WQ
Create version. The duplication was potentially overriding logic that
validated page size.
Link: https://lore.kernel.org/r/20201020202719.54726-6-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Removed unused MRQ-related defines that are not referenced.
Link: https://lore.kernel.org/r/20201020202719.54726-5-james.smart@broadcom.com
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 9816ef6ecbc1 ("scsi: lpfc: Use after free in lpfc_rq_buf_free()")
was made to correct a use after free condition in lpfc_rq_buf_free().
Unfortunately, a subsequent patch cut on a tree without the fix
inadvertently reverted the fix.
Put the fix back: Move the freeing of the rqb_entry to after the print
function that references it.
Link: https://lore.kernel.org/r/20201020202719.54726-4-james.smart@broadcom.com
Fixes: 411de511c694 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c92b ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following calltrace was seen:
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com
Fixes: 411de511c694 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The code to try to shut up sparse warnings about questionable locking
didn't shut up sparse: it made the result not parse as valid C at all,
since the end result now has a label with no statement.
The proper fix is to just always lock the hardware, the same way Bart
did in commit 8ae178760b23 ("scsi: qla2xxx: Simplify the functions for
dumping firmware"). That avoids the whole problem with having locking
that is not statically obvious.
But in the meantime, just remove the incorrect attempt at trying to
avoid a sparse warning that just made things worse.
This was exposed by commit 3e6efab865ac ("scsi: qla2xxx: Fix reset of
MPI firmware"), very similarly to how commit cbb01c2f2f63 ("scsi:
qla2xxx: Fix MPI failure AEN (8200) handling") exposed the same problem
in another place, and caused that commit 8ae178760b23.
Please don't add code to just shut up sparse without actually fixing
what sparse complains about.
Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Arun Easi <aeasi@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A break is not needed if it is preceded by a return or goto.
Link: https://lore.kernel.org/r/20201019142333.16584-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Under fc_host_statistics add statistics for Congestion Signals that are
delivered to the host as interrupt signals.
Link: https://lore.kernel.org/r/20201021092715.22669-5-njavali@marvell.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Parse the incoming FPIN packets and update the host and rport FPIN
statistics based on the FPINs.
Link: https://lore.kernel.org/r/20201021092715.22669-4-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a structure for holding FPIN statistics, for host & rport respectively,
and add associated sysfs nodes:
/sys/class/fc_host/hostXX/statistics/
/sys/class/fc_remote_ports/rport-XX\:Y-Z/statistics/
Link: https://lore.kernel.org/r/20201021092715.22669-3-njavali@marvell.com
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In commit 8d98416a55eb ("scsi: hisi_sas: Switch v3 hw to MQ"), the dispatch
function was changed to choose the delivery queue based on the request tag
HW queue index.
This heavily degrades performance for v2 hw, since the HW queues are not
exposed there, and, as such, HW queue #0 is used for every command.
Revert to previous behaviour for when nr_hw_queues is not set, that being
to choose the HW queue based on target device index.
Link: https://lore.kernel.org/r/1602750425-240341-1-git-send-email-john.garry@huawei.com
Fixes: 8d98416a55eb ("scsi: hisi_sas: Switch v3 hw to MQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a loss of transport due to an adapter migration or crash/disconnect
from the host partner there is a tiny window where we can race adjusting
the request_limit of the adapter. The request limit is atomically
increased/decreased to track the number of inflight requests against the
allowed limit of our VIOS partner.
After a transport loss we set the request_limit to zero to reflect this
state. However, there is a window where the adapter may attempt to queue a
command because the transport loss event hasn't been fully processed yet
and request_limit is still greater than zero. The hypercall to send the
event will fail and the error path will increment the request_limit as a
result. If the adapter processes the transport event prior to this
increment the request_limit becomes out of sync with the adapter state and
can result in SCSI commands being submitted on the now reset connection
prior to an SRP Login resulting in a protocol violation.
Fix this race by protecting request_limit with the host lock when changing
the value via atomic_set() to indicate no transport.
Link: https://lore.kernel.org/r/20201025001355.4527-1-tyreld@linux.ibm.com
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the fcport is about to be deleted we should return EBUSY instead of
ENODEV. Only for EBUSY will the request be requeued in a multipath setup.
Also return EBUSY when the firmware has not yet started to avoid dropping
the request.
Link: https://lore.kernel.org/r/20201014073048.36219-1-dwagner@suse.de
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current scanning mechanism is supposed to fall back to a synchronous
host scan if an asynchronous scan is in progress. However, this rule isn't
strictly respected, scsi_prep_async_scan() doesn't hold scan_mutex when
checking shost->async_scan. When scsi_scan_host() is called concurrently,
two async scans on same host can be started and a hang in do_scan_async()
is observed.
Fixes this issue by checking & setting shost->async_scan atomically with
shost->scan_mutex.
Link: https://lore.kernel.org/r/20201010032539.426615-1-ming.lei@redhat.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph
- rdma error handling fixes (Chao Leng)
- fc error handling and reconnect fixes (James Smart)
- fix the qid displace when tracing ioctl command (Keith Busch)
- don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
- fix MTDT for passthru (Logan Gunthorpe)
- blacklist Write Same on more devices (Kai-Heng Feng)
- fix an uninitialized work struct (zhenwei pi)"
- lightnvm out-of-bounds fix (Colin)
- SG allocation leak fix (Doug)
- rnbd fixes (Gioh, Guoqing, Jack)
- zone error translation fixes (Keith)
- kerneldoc markup fix (Mauro)
- zram lockdep fix (Peter)
- Kill unused io_context members (Yufen)
- NUMA memory allocation cleanup (Xianting)
- NBD config wakeup fix (Xiubo)
* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
block: blk-mq: fix a kernel-doc markup
nvme-fc: shorten reconnect delay if possible for FC
nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
nvme-fc: fix error loop in create_hw_io_queues
nvme-fc: fix io timeout to abort I/O
null_blk: use zone status for max active/open
nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
nvmet: cleanup nvmet_passthru_map_sg()
nvmet: limit passthru MTDS by BIO_MAX_PAGES
nvmet: fix uninitialized work for zero kato
nvme-pci: disable Write Zeroes on Sandisk Skyhawk
nvme: use queuedata for nvme_req_qid
nvme-rdma: fix crash due to incorrect cqe
nvme-rdma: fix crash when connect rejected
block: remove unused members for io_context
blk-mq: remove the calling of local_memory_node()
zram: Fix __zram_bvec_{read,write}() locking order
skd_main: remove unused including <linux/version.h>
sgl_alloc_order: fix memory leak
lightnvm: fix out-of-bounds write to array devices->info[]
...
|
|
Pull more SCSI updates from James Bottomley:
"The set of core changes here is Christoph's submission path cleanups.
These introduced a couple of regressions when first proposed so they
got held over from the initial merge window pull request to give more
testing time, which they've now had and Syzbot has confirmed the
regression it detected is fixed.
The other main changes are two driver updates (arcmsr, pm80xx) and
assorted minor clean ups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: qla2xxx: Fix return of uninitialized value in rval
scsi: core: Set sc_data_direction to DMA_NONE for no-transfer commands
scsi: sr: Initialize ->cmd_len
scsi: arcmsr: Update driver version to v1.50.00.02-20200819
scsi: arcmsr: Add support for ARC-1886 series RAID controllers
scsi: arcmsr: Fix device hot-plug monitoring timer stop
scsi: arcmsr: Remove unnecessary syntax
scsi: pm80xx: Driver version update
scsi: pm80xx: Increase the number of outstanding I/O supported to 1024
scsi: pm80xx: Remove DMA memory allocation for ccb and device structures
scsi: pm80xx: Increase number of supported queues
scsi: sym53c8xx_2: Fix sizeof() mismatch
scsi: isci: Fix a typo in a comment
scsi: qla4xxx: Fix inconsistent format argument type
scsi: myrb: Fix inconsistent format argument types
scsi: myrb: Remove redundant assignment to variable timeout
scsi: bfa: Fix error return in bfad_pci_init()
scsi: fcoe: Simplify the return expression of fcoe_sysfs_setup()
scsi: snic: Simplify the return expression of svnic_cq_alloc()
scsi: fnic: Simplify the return expression of vnic_wq_copy_alloc()
...
|
|
Pull powerpc updates from Michael Ellerman:
- A series from Nick adding ARCH_WANT_IRQS_OFF_ACTIVATE_MM & selecting
it for powerpc, as well as a related fix for sparc.
- Remove support for PowerPC 601.
- Some fixes for watchpoints & addition of a new ptrace flag for
detecting ISA v3.1 (Power10) watchpoint features.
- A fix for kernels using 4K pages and the hash MMU on bare metal
Power9 systems with > 16TB of RAM, or RAM on the 2nd node.
- A basic idle driver for shallow stop states on Power10.
- Tweaks to our sched domains code to better inform the scheduler about
the hardware topology on Power9/10, where two SMT4 cores can be
presented by firmware as an SMT8 core.
- A series doing further reworks & cleanups of our EEH code.
- Addition of a filter for RTAS (firmware) calls done via sys_rtas(),
to prevent root from overwriting kernel memory.
- Other smaller features, fixes & cleanups.
Thanks to: Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Athira Rajeev, Biwen Li, Cameron Berkenpas, Cédric Le Goater, Christophe
Leroy, Christoph Hellwig, Colin Ian King, Daniel Axtens, David Dai, Finn
Thain, Frederic Barrat, Gautham R. Shenoy, Greg Kurz, Gustavo Romero,
Ira Weiny, Jason Yan, Joel Stanley, Jordan Niethe, Kajol Jain, Konrad
Rzeszutek Wilk, Laurent Dufour, Leonardo Bras, Liu Shixin, Luca
Ceresoli, Madhavan Srinivasan, Mahesh Salgaonkar, Nathan Lynch, Nicholas
Mc Guire, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran, Pedro
Miraglia Franco de Carvalho, Pratik Rajesh Sampat, Qian Cai, Qinglang
Miao, Ravi Bangoria, Russell Currey, Satheesh Rajendran, Scott Cheloha,
Segher Boessenkool, Srikar Dronamraju, Stan Johnson, Stephen Kitt,
Stephen Rothwell, Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, Vasant Hegde, Wang Wensheng, Wolfram Sang, Yang
Yingliang, zhengbin.
* tag 'powerpc-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (228 commits)
Revert "powerpc/pci: unmap legacy INTx interrupts when a PHB is removed"
selftests/powerpc: Fix eeh-basic.sh exit codes
cpufreq: powernv: Fix frame-size-overflow in powernv_cpufreq_reboot_notifier
powerpc/time: Make get_tb() common to PPC32 and PPC64
powerpc/time: Make get_tbl() common to PPC32 and PPC64
powerpc/time: Remove get_tbu()
powerpc/time: Avoid using get_tbl() and get_tbu() internally
powerpc/time: Make mftb() common to PPC32 and PPC64
powerpc/time: Rename mftbl() to mftb()
powerpc/32s: Remove #ifdef CONFIG_PPC_BOOK3S_32 in head_book3s_32.S
powerpc/32s: Rename head_32.S to head_book3s_32.S
powerpc/32s: Setup the early hash table at all time.
powerpc/time: Remove ifdef in get_dec() and set_dec()
powerpc: Remove get_tb_or_rtc()
powerpc: Remove __USE_RTC()
powerpc: Tidy up a bit after removal of PowerPC 601.
powerpc: Remove support for PowerPC 601
powerpc: Remove PowerPC 601
powerpc: Drop SYNC_601() ISYNC_601() and SYNC()
powerpc: Remove CONFIG_PPC601_SYNC_FIX
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
|
|
Pull SPDX updates from Greg KH:
"Here are some SPDX-specific changes for 5.10-rc1.
They include:
- driver fixes to make spdxcheck.pl work properly
- add GFDL licenses as "deprecated" but required due to some of our
documentation using them
- add Zlib license as "deprecated" but required because we have code
with this license in the tree.
- convert some drivers to have SPDX identifiers that previously
didn't have them.
All have been in linux-next for a very long time with no reported
issues"
* tag 'spdx-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
scripts/spdxcheck.py: handle license identifiers in XML comments
net/mlx5: IPsec: make spdxcheck.py happy
LICENSES/deprecated: add Zlib license text
LICENSE: add GFDL deprecated licenses
net/qla3xxx: Convert to SPDX license identifiers
net/qlge: Convert to SPDX license identifiers
net/qlcnic: Convert to SPDX license identifiers
scsi/qla2xxx: Convert to SPDX license identifiers
scsi/qla4xxx: Convert to SPDX license identifiers
|
|
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
|
|
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
|
|
ZBC or ZAC disks that have a limit on the number of open zones may fail
a zone open command or a write to a zone that is not already implicitly
or explicitly open if the total number of open zones is already at the
maximum allowed.
For these operations, instead of returning the generic BLK_STS_IOERR,
return BLK_STS_ZONE_OPEN_RESOURCE which is returned as -ETOOMANYREFS to
the I/O issuer, allowing the device user to act appropriately on these
relatively benign zone resource errors.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull block driver updates from Jens Axboe:
"Here are the driver updates for 5.10.
A few SCSI updates in here too, in coordination with Martin as they
depend on core block changes for the shared tag bitmap.
This contains:
- NVMe pull requests via Christoph:
- fix keep alive timer modification (Amit Engel)
- order the PCI ID list more sensibly (Andy Shevchenko)
- cleanup the open by controller helper (Chaitanya Kulkarni)
- use an xarray for the CSE log lookup (Chaitanya Kulkarni)
- support ZNS in nvmet passthrough mode (Chaitanya Kulkarni)
- fix nvme_ns_report_zones (Christoph Hellwig)
- add a sanity check to nvmet-fc (James Smart)
- fix interrupt allocation when too many polled queues are
specified (Jeffle Xu)
- small nvmet-tcp optimization (Mark Wunderlich)
- fix a controller refcount leak on init failure (Chaitanya
Kulkarni)
- misc cleanups (Chaitanya Kulkarni)
- major refactoring of the scanning code (Christoph Hellwig)
- MD updates via Song:
- Bug fixes in bitmap code, from Zhao Heming
- Fix a work queue check, from Guoqing Jiang
- Fix raid5 oops with reshape, from Song Liu
- Clean up unused code, from Jason Yan
- Discard improvements, from Xiao Ni
- raid5/6 page offset support, from Yufen Yu
- Shared tag bitmap for SCSI/hisi_sas/null_blk (John, Kashyap,
Hannes)
- null_blk open/active zone limit support (Niklas)
- Set of bcache updates (Coly, Dongsheng, Qinglang)"
* tag 'drivers-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (78 commits)
md/raid5: fix oops during stripe resizing
md/bitmap: fix memory leak of temporary bitmap
md: fix the checking of wrong work queue
md/bitmap: md_bitmap_get_counter returns wrong blocks
md/bitmap: md_bitmap_read_sb uses wrong bitmap blocks
md/raid0: remove unused function is_io_in_chunk_boundary()
nvme-core: remove extra condition for vwc
nvme-core: remove extra variable
nvme: remove nvme_identify_ns_list
nvme: refactor nvme_validate_ns
nvme: move nvme_validate_ns
nvme: query namespace identifiers before adding the namespace
nvme: revalidate zone bitmaps in nvme_update_ns_info
nvme: remove nvme_update_formats
nvme: update the known admin effects
nvme: set the queue limits in nvme_update_ns_info
nvme: remove the 0 lba_shift check in nvme_update_ns_info
nvme: clean up the check for too large logic block sizes
nvme: freeze the queue over ->lba_shift updates
nvme: factor out a nvme_configure_metadata helper
...
|
|
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
|
|
Pull compat iovec cleanups from Al Viro:
"Christoph's series around import_iovec() and compat variant thereof"
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
security/keys: remove compat_keyctl_instantiate_key_iov
mm: remove compat_process_vm_{readv,writev}
fs: remove compat_sys_vmsplice
fs: remove the compat readv/writev syscalls
fs: remove various compat readv/writev helpers
iov_iter: transparently handle compat iovecs in import_iovec
iov_iter: refactor rw_copy_check_uvector and import_iovec
iov_iter: move rw_copy_check_uvector() into lib/iov_iter.c
compat.h: fix a spelling error in <linux/compat.h>
|
Sreekanth Reddy
Hannes Reinecke
Linus Torvalds
ching Huang
Asutosh Das
Can Guo
Keita Suzuki
Arnd Bergmann
Mauro Carvalho Chehab
James Smart
Tom Rix
Shyam Sundar
John Garry
Tyrel Datwyler
Daniel Wagner
Ming Lei
Damien Le Moal