| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds the fnic devcmd2 controller definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds the fnic devcmd2 command structre and the command result
structure definitions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Impose an upper limit on the max number of CQ entries (corresponding to the
copy wq) processed in an interrupt. Use module parameter to set the limit.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Do RQ enable before posting descriptor. This is needed for later hw
revisions.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Doing vnic_device_enable before this could cause interrupts to happen
before they are setup.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The change is to print warning when scsi done is called for an IO that has
not yet been issued to the fw. Also adding sc and tag to debug print when
IO is cleaned up.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This change is to add fnic stats for the max number of CQs (corresponding
to copy WQ) processed in a given interrupt, max time taken by the ISR.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds the current fnic port speed stat to fnic debug stats.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Need to use fnic_lock as well as host lock in that order to set state
flags.
[mkp: typos]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
rq->ctrl not enabled when this is called is bad but not fatal and can
continue.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch changes the default lun queuedepth for fnic to 256.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch is to add fnic 20G port speed display in sysfs.
[mkp: typo]
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
From scsi_init_command(), a function called by scsi_mq_prep_fn():
/* zero out the cmd, except for the embedded scsi_request */
memset((char *)cmd + sizeof(cmd->req), 0,
sizeof(*cmd) - sizeof(cmd->req) + dev->host->hostt->cmd_size);
In other words, scsi_mq_prep_fn() clears scsi_cmnd.flags. Hence move the
clear_bit() call into the else branch, the only branch in which this code
is necessary.
See also commit f1342709d18a ("scsi: Do not rely on blk-mq for double
completions").
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch makes the source code more uniform and does not change any
functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rework sd_setup_read_write_cmnd() so it becomes more readable. Put all the
sanity checking at the head of the function and sanitize the logged error
messages. Move the legacy SCSI logging calls to the end of the functions
and reduce conditional nesting.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Create a helper function for each of the 6, 10, 16 and 32-byte READ/WRITE
variants and use those when setting up reads and writes.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 and made
function names shorter. ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid open coding the checks for the supported logical block sizes and use
a mask to check for misaligned I/O. Use our helper functions to scale lba
and block count.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We have had several bugs due mixing sector and logical block size
terminology. In the block layer, a sector is a 512-byte unit regardless of
the logical block size of the underlying device. But the term "sector" is
still widely used in sd.c when referring to logical block sized units.
We previously introduced helper functions such as sectors_to_logical() and
logical_to_sectors() to make the distinction clear. Use these to make the
code in sd.c consistent wrt. logical blocks and block layer sectors.
Use "lba" to describe a logical block address and "nr_blocks" when counting
logical blocks. SBC uses "TRANSFER LENGTH" to describe the latter but this
term was avoided to prevent confusion with the very similar DMA transfer
size (->transfersize) which is counted in bytes.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch does not change any functionality.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
memcpy_fromio() doesn't provide any control over access size. For example,
on arm64, it is implemented using readb and readq. This may trigger a
synchronous external abort:
[ 3.729943] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
[ 3.737000] Modules linked in:
[ 3.744371] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G S 4.20.0-rc4 #16
[ 3.747413] Hardware name: Qualcomm Technologies, Inc. MSM8998 v1 MTP (DT)
[ 3.755295] pstate: 00000005 (nzcv daif -PAN -UAO)
[ 3.761978] pc : __memcpy_fromio+0x68/0x80
[ 3.766718] lr : ufshcd_dump_regs+0x50/0xb0
[ 3.770767] sp : ffff00000807ba00
[ 3.774830] x29: ffff00000807ba00 x28: 00000000fffffffb
[ 3.778344] x27: ffff0000089db068 x26: ffff8000f6e58000
[ 3.783728] x25: 000000000000000e x24: 0000000000000800
[ 3.789023] x23: ffff8000f6e587c8 x22: 0000000000000800
[ 3.794319] x21: ffff000008908368 x20: ffff8000f6e1ab80
[ 3.799615] x19: 000000000000006c x18: ffffffffffffffff
[ 3.804910] x17: 0000000000000000 x16: 0000000000000000
[ 3.810206] x15: ffff000009199648 x14: ffff000089244187
[ 3.815502] x13: ffff000009244195 x12: ffff0000091ab000
[ 3.820797] x11: 0000000005f5e0ff x10: ffff0000091998a0
[ 3.826093] x9 : 0000000000000000 x8 : ffff8000f6e1ac00
[ 3.831389] x7 : 0000000000000000 x6 : 0000000000000068
[ 3.836676] x5 : ffff8000f6e1abe8 x4 : 0000000000000000
[ 3.841971] x3 : ffff00000928c868 x2 : ffff8000f6e1abec
[ 3.847267] x1 : ffff00000928c868 x0 : ffff8000f6e1abe8
[ 3.852567] Process swapper/0 (pid: 1, stack limit = 0x(____ptrval____))
[ 3.857900] Call trace:
[ 3.864473] __memcpy_fromio+0x68/0x80
[ 3.866683] ufs_qcom_dump_dbg_regs+0x1c0/0x370
[ 3.870522] ufshcd_print_host_regs+0x168/0x190
[ 3.874946] ufshcd_init+0xd4c/0xde0
[ 3.879459] ufshcd_pltfrm_init+0x3c8/0x550
[ 3.883264] ufs_qcom_probe+0x24/0x60
[ 3.887188] platform_drv_probe+0x50/0xa0
Assuming aligned 32-bit registers, let's use readl, after making sure
that 'offset' and 'len' are indeed multiples of 4.
Fixes: ba80917d9932d ("scsi: ufs: ufshcd_dump_regs to use memcpy_fromio")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Assign fc_vport to ln->fc_vport before calling csio_fcoe_alloc_vnp() to
avoid a NULL pointer dereference in csio_vport_set_state().
ln->fc_vport is dereferenced in csio_vport_set_state().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We cannot wait on a completion object in the lpfc_nvme_lport structure in
the _destroy_localport() code path because the NVMe/fc transport will free
that structure immediately after the .localport_delete() callback. This
results in a use-after-free, and a hang if slub_debug=FZPU is enabled.
Fix this by putting the completion on the stack.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a host driver sets a maximum segment size we should not only propagate
that setting to the block layer, which can merge segments, but also to the
DMA mapping layer which can merge segments as well.
Fixes: 50c2e9107f ("scsi: introduce a max_segment_size host_template parameters")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace nvram_* functions with static functions in nvram.h. These will
become wrappers for struct nvram_ops method calls.
This patch effectively disables existing NVRAM functionality so as to
allow the rest of the series to be bisected without build failures.
That functionality is gradually re-implemented in subsequent patches.
Replace the sole validate-checksum-and-read-byte sequence with a call to
nvram_read() which will gain the same semantics in subsequent patches.
Remove unused exports.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On powerpc, setting CONFIG_NVRAM=n builds a kernel with no NVRAM support.
Setting CONFIG_NVRAM=m enables the /dev/nvram misc device module without
enabling NVRAM support in drivers. Setting CONFIG_NVRAM=y enables the
misc device (built-in) and also enables NVRAM support in drivers.
m68k shares the valkyriefb driver with powerpc, and since that driver uses
NVRAM, it is affected by CONFIG_ATARI_SCSI, because of the use of
"select NVRAM". We can avoid the "select" here, but drivers still have
to interpret the CONFIG_NVRAM symbol consistently regardless of platform.
In this patch and the subsequent fbdev driver patch, the convention is
adopted across all relevant platforms whereby NVRAM functionality gets
enabled in a given device driver when the nvram misc device is built-in
or when both drivers are modules.
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
|
|
CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.
Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In case of ->set_param() and ->bind_conn() cxgb4i driver does not wait for
cmd completion, this can create race conditions, to avoid this add
wait_for_completion().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After Commit 54aed4dd3526 ("MIPS: IP27: use dma_direct_ops") qla1280 driver
failed on SGI IP27 machines with
qla1280: QLA1040 found on PCI bus 0, dev 0
qla1280 0000:00:00.0: enabling device (0006 -> 0007)
qla1280: Failed to get request memory
qla1280: probe of 0000:00:00.0 failed with error -12
Reason is that SGI IP27 always generates 64bit DMA addresses and has no
fallback mode for 32bit DMA addresses implemented. QLA1280 supports 64bit
addressing for all DMA accesses so setting coherent mask to 64bit fixes the
issue.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Albeit we no longer rely on those hard-coded descriptor sizes, we still use
them as our defaults, so better get it right. While adding its sysfs
entries, we forgot to update the geometry descriptor size. It is 0x48
according to UFS2.1, and wasn't changed in UFS3.0.
[mkp: typo]
Fixes: c720c091222e (scsi: ufs: sysfs: geometry descriptor)
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The tmscsim.txt doc file was removed in c121107d0f84.
Fixes: c121107d0f84 ("scsi: documentation: Obsolete documentation references")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
commit 272652fcbf1a ("scsi: megaraid_sas: add retry logic in megasas_readl")
missed changing readl to megasas_readl in megasas_clear_intr_fusion(). For
Aero controllers, reads of outbound_intr_status register needs to be
retried.
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the driver finds invalid destination MAC for the first un-reachable
target, and before completes the PATH_REQ operation, set new ep_state to
OFFLDCONN_NONE so that as part of driver ep_poll mechanism, the upper
open-iscsi layer is notified to complete the login process on the first
un-reachable target and thus proceed login to other reachable targets.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
hba->is_sys_suspended is set after successful system suspend but
not clear after successful system resume.
According to current behavior, hba->is_sys_suspended will not be set if
host is runtime-suspended but not system-suspended. Thus we shall aligh the
same policy: clear this flag even if host remains runtime-suspended after
ufshcd_system_resume is successfully returned.
Simply fix this flag to correct host status logs.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When SCSI-MQ is enabled, in some case system would present
nr_possible_cpus() which is greater than requested vectors by the
driver. This results into driver being able to get larger number of MSI-X
vectors than actual online CPUs. Driver then uses
pci_alloc_irq_vectors_affinity() to assign 1:1 mapping and affinity for
each MSI-x vector to CPUs. When the command is submitted using MSI-x
vector, assigned to offline CPU, it results in an ABTS and system
hang. This hang is result of a driver not being able to process interrupt
on a vector assigned to an Off-line CPUs
This patch fixes this issue by setting irq_offset value for the
blk_mq_pci_map_queues() to use only those CPUs which has CPU mask affinity
assigned and are online. By using the irq_offset value, driver will allow
online cpumask to decide which vectors are used in blk_mq_pci_map_queues().
Fixes: 5601236b6f794 ("scsi: qla2xxx: Add Block Multi Queue functionality.")
Cc: <stable@vger.kernel.org> #4.19
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.
Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bradley Grove <bgrove@atto.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently we set the protection parameters after calling scsi_add_host()
for v3 hw.
They should be set beforehand, so make this change.
Appearantly this fixes our DIX issue (not mainline yet) also, but more
testing required.
Fixes: d6a9000b81be ("scsi: hisi_sas: Add support for DIF feature for v2 hw")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The return statement is indented incorrectly, fix this by removing a single
tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently the protection lookup tables in sd_prot_flag_mask() and
sd_prot_op() are declared as non-static. As such, they will be rebuilt for
each respective function call.
Optimise by making them static.
This saves ~100B object code for sd.c:
Before:
text data bss dec hex filename
25403 1024 16 26443 674b drivers/scsi/sd.o
After:
text data bss dec hex filename
25299 1024 16 26339 66e3 drivers/scsi/sd.o
In addition, since those same functions are declared in sd.h, but each are
only referenced in sd.c, relocate them to that same c file.
The inline specifier is dropped also, since gcc should be able to make the
decision to inline.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
Satish Kharat
Bart Van Assche
Martin K. Petersen
Marc Gonzalez
Varun Prakash
Ewan D. Milne
Christoph Hellwig
Finn Thain
Linus Torvalds
Evan Green
Thomas Bogendoerfer
Avri Altman
Otto Sabart
Shivasharan S
Manish Rangankar
Stanley Chu
John Garry
Giridhar Malavali
Ming Lei
Gustavo A. R. Silva
Colin Ian King