| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Comment should have said Repost.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
The xri resources are split into pools for NVME and FCP IO when NVME is
enabled. There was not message in the log that identified this allocation.
Added debug message to log XRI split.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
In the lpfc_nvme_io_cmd_wqe_cmpl routine the driver was printing two
pointers and the DID for the rport whenever an IO completed on a now
that had transitioned to a non active state.
There is no need to print the node pointer address for a node that
is not active the DID should be enough to debug.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
In this case, the NVME initiator is sending an LS REQ command on an NDLP
that is not MAPPED. The FW rejects it.
The lpfc_nvme_ls_req routine checks for a NULL ndlp pointer
but does not check the NDLP state. This allows the routine
to send an LS IO when the ndlp is disconnected.
Check the ndlp for NULL, actual node, Target and MAPPED
or Initiator and UNMAPPED. This avoids Fabric nodes getting
the Create Association or Create Connection commands. Initiators
are free to Reject either Create.
Also some of the messages numbers in lpfc_nvme_ls_req were changed because
they were already used in other log messages.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
During some link event testing it was observed that the
wait_for_completion_timeout in the lpfc_nvme_unregister_port
was timing out all the time.
The initiator is claiming the nvme_fc_unregister_remoteport upcall is
not completing the unregister in the time allotted.
[ 2186.151317] lpfc 0000:07:00.0: 0:(0):6169 Unreg nvme wait failed 0
The wait_for_completion_timeout returns 0 when the wait has
been outstanding for the jiffies passed by the caller. In this error
message, the nvme initiator passed value 5 - meaning 5 jiffies -
and this is just wrong.
Calculate 5 seconds in Jiffies and pass that value
from the current jiffies.
Also the log message for the unregister timeout was reduced
because timeout failure is the same as timeout.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Standardize default SGL segment count for nvme target and initiator
The driver needs to make them the same for clarity.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
target transport:
----------------------
There are cases when there is a need to abort in-progress target
operations (writedata) so that controller termination or errors can
clean up. That can't happen currently as the abort is another target
op type, so it can't be used till the running one finishes (and it may
not). Solve by removing the abort op type and creating a separate
downcall from the transport to the lldd to request an io to be aborted.
The transport will abort ios on queue teardown or io errors. In general
the transport tries to call the lldd abort only when the io state is
idle. Meaning: ops that transmit data (readdata or rsp) will always
finish their transmit (or the lldd will see a state on the
link or initiator port that fails the transmit) and the done call for
the operation will occur. The transport will wait for the op done
upcall before calling the abort function, and as the io is idle, the
io can be cleaned up immediately after the abort call; Similarly, ios
that are not waiting for data or transmitting data must be in the nvmet
layer being processed. The transport will wait for the nvmet layer
completion before calling the abort function, and as the io is idle,
the io can be cleaned up immediately after the abort call; As for ops
that are waiting for data (writedata), they may be outstanding
indefinitely if the lldd doesn't see a condition where the initiatior
port or link is bad. In those cases, the transport will call the abort
function and wait for the lldd's op done upcall for the operation, where
it will then clean up the io.
Additionally, if a lldd receives an ABTS and matches it to an outstanding
request in the transport, A new new transport upcall was created to abort
the outstanding request in the transport. The transport expects any
outstanding op call (readdata or writedata) will completed by the lldd and
the operation upcall made. The transport doesn't act on the reported
abort (e.g. clean up the io) until an op done upcall occurs, a new op is
attempted, or the nvmet layer completes the io processing.
fcloop:
----------------------
Updated to support the new target apis.
On fcp io aborts from the initiator, the loopback context is updated to
NULL out the half that has completed. The initiator side is immediately
called after the abort request with an io completion (abort status).
On fcp io aborts from the target, the io is stopped and the initiator side
sees it as an aborted io. Target side ops, perhaps in progress while the
initiator side is done, continue but noop the data movement as there's no
structure on the initiator side to reference.
patch also contains:
----------------------
Revised lpfc to support the new abort api
commonized rsp buffer syncing and nulling of private data based on
calling paths.
errors in op done calls don't take action on the fod. They're bad
operations which implies the fod may be bad.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
With the advent of the opdone calls changing context, the lldd can no
longer assume that once the op->done call returns for RSP operations
that the request struct is no longer being accessed.
As such, revise the lldd api for a req_release callback that the
transport will call when the job is complete. This will also be used
with abort cases.
Fixed text in api header for change in io complete semantics.
Revised lpfc to support the new req_release api.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Two new feature flags were added to control whether upcalls to the
transport result in context switches or stay in the calling context.
NVMET_FCTGTFEAT_CMD_IN_ISR:
By default, if the flag is not set, the transport assumes the
lldd is in a non-isr context and in the cpu context it should be
for the io queue. As such, the cmd handler is called directly in the
calling context.
If the flag is set, indicating the upcall is an isr context, the
transport mandates a transition to a workqueue. The workqueue assigned
to the queue is used for the context.
NVMET_FCTGTFEAT_OPDONE_IN_ISR
By default, if the flag is not set, the transport assumes the
lldd is in a non-isr context and in the cpu context it should be
for the io queue. As such, the fcp operation done callback is called
directly in the calling context.
If the flag is set, indicating the upcall is an isr context, the
transport mandates a transition to a workqueue. The workqueue assigned
to the queue is used for the context.
Updated lpfc for flags
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Move scsi_remove_host call into sas_remove_host and remove it from SAS
HBA drivers, so we don't mess up the ordering. This solves an issue with
double deleting sysfs entries that was introduced by the change of sysfs
behaviour from commit bcdde7e221a8 ("sysfs: make __sysfs_remove_dir()
recursive").
[mkp: addressed checkpatch complaints]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Jinpu Wang <jinpu.wang@profitbricks.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Trivial fix to spelling mistake, adatper_reset_req should be
adapter_reset_req. Also break up very long seq_printf statement into
multiple lines.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. This also initializes the
array members using the enum used to look up __port_action entries.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that all drivers that call blk_mq_complete_requests have a
->complete callback we can remove the direct call to blk_mq_end_request,
as well as the error argument to blk_mq_complete_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This passes on the scsi_cmnd result field to users of passthrough
requests. Currently we abuse req->errors for this purpose, but that
field will go away in its current form.
Note that the old IDE code abuses the errors field in very creative
ways and stores all kinds of different values in it. I didn't dare
to touch this magic, so the abuses are brought forward 1:1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The function only returns -EIO if rq->errors is non-zero, which is not
very useful and lets a large number of callers ignore the return value.
Just let the callers figure out their error themselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/scsi/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "Juergen E. Fischer" <fischer@norbit.de>
cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
cc: "Martin K. Petersen" <martin.petersen@oracle.com>
cc: Dario Ballabio <ballabio_dario@emc.com>
cc: Finn Thain <fthain@telegraphics.com.au>
cc: Michael Schmitz <schmitzmic@gmail.com>
cc: Achim Leubner <achim_leubner@adaptec.com>
cc: linux-scsi@vger.kernel.org
|
|
The vendor/device and subvendor/subdevice arguments to the function
prototype ahc_9005_subdevinfo_valid are in the wrong order and need to
be swapped to fix this. Detected with PVS-Studio studio.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Just call the functions directly and remove a giant pile of boilerplate
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Prepare to mark sensitive kernel structures for randomization by making
sure they're using designated initializers. These were identified during
allyesconfig builds of x86, arm, and arm64, with most initializer fixes
extracted from grsecurity.
For these cases, terminate the list with { }, which will be zero-filled,
instead of undesignated NULLs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Included in the current storvsc driver for Hyper-V is the ability to
access luns on an FC fabric via a virtualized fiber channel adapter
exposed by the Hyper-V host. The driver also attaches to the FC
transport to allow host and port names to be published under
/sys/class/fc_host/hostX. Current customer tools running on the VM
require that these names be available in the well known standard
location under fc_host/hostX.
This patch stubs in an rport per fc_host and sets its rport role as
FC_PORT_ROLE_FCP_DUMMY_INITIATOR to indicate to the fc_transport that it
is a pseudo rport in order to scan the scsi stack via echo "- - -" >
/sys/class/scsi_host/hostX/scan.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch allows scsi drivers that expose virturalized fibre channel
devices but that do not expose rports to successfully rescan the scsi
bus via echo "- - -" > /sys/class/scsi_host/hostX/scan. Drivers can
create a pseudo rport and indicate FC_PORT_ROLE_FCP_DUMMY_INITIATOR as
the rport's role in fc_rport_identifiers. This insures that a valid
scsi_target_id is assigned to the newly created rport and it can meet
the requirements of fc_user_scan_tgt calling scsi_scan_target.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Passed through SCSI targets may have transfer limits which come from the
host SCSI controller or something on the host side other than the target
itself.
To make this work properly, the hypervisor can adjust the target's VPD
information to advertise these limits. But for that to work, the guest
has to look at the VPD pages, which we won't do by default if it is an
SPC-2 device, even if it does actually support it.
This adds a workaround to address this, forcing devices attached to a
virtio-scsi controller to always check the VPD pages. This is modelled
on a similar workaround for the storvsc (Hyper-V) SCSI controller,
although that exists for slightly different reasons.
A specific case which causes this is a volume from IBM's IPR RAID
controller (which presents as an SPC-2 device, although it does support
VPD) passed through with qemu's 'scsi-block' device.
[mkp: fixed typo]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes a potential buffer overflow in lpfc_nvme_info_show().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The check for an unsigned long being less than zero is always false so
it is a redundant check and can be removed.
Detected by static analysis with by PVS-Studio
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
mempool_alloc() cannot fail when passed GFP_NOIO or any other gfp
setting that is permitted to sleep. So remove this pointless code.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull SCSI fixes from James Bottomley:
"This is seven small fixes which are all for user visible issues that
fortunately only occur in rare circumstances.
The most serious is the sr one in which QEMU can cause us to read
beyond the end of a buffer (I don't think it's exploitable, but just
in case).
The next is the sd capacity fix which means all non 512 byte sector
drives greater than 2TB fail to be correctly sized.
The rest are either in new drivers (qedf) or on error legs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
scsi: aacraid: fix PCI error recovery path
scsi: sd: Fix capacity calculation with 32-bit sector_t
scsi: qla2xxx: Add fix to read correct register value for ISP82xx.
scsi: qedf: Fix crash due to unsolicited FIP VLAN response.
scsi: sr: Sanity check returned mode data
scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable
|
|
|
|
storvsc_on_channel_callback is a void function and the return
statement at the end is not useful.
Found with checkpatch.
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use kcalloc for allocating an array instead of kzalloc with multiply,
kcalloc is the preferred API.
Found with checkpatch.
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As an enhancement to distribute requests to multiple hardware queues, add the
infrastructure to hash a SCSI command into a particular hardware queue.
Support the following scenarios when deriving which queue to use: single
queue, tagging when SCSI-MQ enabled, and simple hash via CPU ID when SCSI-MQ
is disabled. Rather than altering the existing send API, the derived hardware
queue is stored in the AFU command where it can be used for sending a command
to the chosen hardware queue.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As staging for supporting multiple hardware queues, add an attribute to show
and set the current number of hardware queues for the host. Support specifying
a hard limit or a CPU affinitized value. This will allow the number of
hardware queues to be tuned by a system administrator.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Introduce multiple hardware queues to improve legacy I/O path performance.
Each hardware queue is comprised of a master context and associated I/O
resources. The hardware queues are initially implemented as a static array
embedded in the AFU. This will be transitioned to a dynamic allocation in a
later series to improve the memory footprint of the driver.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The method used to decode asynchronous interrupts involves unnecessary loops
to match up bits that are set with corresponding entries in the asynchronous
interrupt information table. This algorithm is wasteful and does not scale
well as new status bits are supported.
As an improvement, use the for_each_set_bit() service to iterate over the
asynchronous status bits and refactor the information table such that it can
be indexed by bit position.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As a general cleanup, address all reasonable checkpatch warnings and
errors. These include enforcement of comment styles and including named
identifiers in function prototypes.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Validation statements to enforce assumptions about specific defines are not
being evaluated by the compiler due to the fact that they reside in a routine
that is not used. To activate them, call the routine as part of module
initialization. As an additional, related cleanup, remove the now-defunct
CXLFLASH_NUM_CMDS.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Devices supported by the cxlflash driver are fully coherent and do not require
a bus address mapping. Avoid unnecessary path length by using the virtual
address and length already present in the scatter-gather entry.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
An EEH during probe can lead to a crash as the recovery thread races with the
probe thread. To avoid this issue, introduce new states to fence out EEH
recovery until probe has completed. Also ensure the reset wait queue is
flushed during device removal to avoid orphaned threads.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update the driver to allow for future cards with 4 ports.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update the SISlite header to support 4 ports as outlined in the SISlite
specification. Address fallout from structure renames and refreshed
organization throughout the driver. Determine the number of ports supported by
a card from the global port selection mask register reset value.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As staging to support FC-related updates to the SISlite specification,
introduce helper routines to obtain references to FC resources that exist
within the global map. This will allow changes to the underlying global map
structure without impacting existing code paths.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
At present, the cxlflash driver only supports hardware with two FC ports. The
code was initially designed with this assumption and is dependent on having
two FC ports - adding more ports will break logic within the driver.
To mitigate this issue, remove the existing port assumptions and transition
the code to support more than two ports. As a side effect, clarify the
interpretation of the DK_CXLFLASH_ALL_PORTS_ACTIVE flag.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Transition from a static number of FC ports to a value that is derived during
probe. For now, a static value is used but this will later be based on the
type of card being configured.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As staging for future function, pass the config pointer instead of the AFU
pointer for port-related sysfs helper routines.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, RRQ processing takes place on hardware interrupt context. This can
be a heavy burden in some environments due to the overhead encountered while
completing RRQ entries. In an effort to improve system performance, use the
IRQ polling API to schedule this processing on softirq context.
This function will be disabled by default until starting values can be
established for the hardware supported by this driver.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As further staging to support processing the HRRQ by other means, access to
the HRRQ needs to be serialized by a disabled lock. This will allow safe
access in other non-hardware interrupt contexts. In an effort to minimize the
period where interrupts are disabled, support is added to queue up commands
harvested from the RRQ such that they can be processed with hardware
interrupts enabled. While this doesn't offer any improvement with processing
on a hardware interrupt it will help when IRQ polling is supported and the
command completions can execute on softirq context.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In order to support processing the HRRQ by other means (e.g. polling), the
processing portion of the current RRQ interrupt handler needs to be broken out
into a separate routine. This will allow RRQ processing from places other than
the RRQ hardware interrupt handler.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Trivial fix to spelling mistake in SNIC_ERR error message text, one
cannot have "Cann't".
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
James Smart
Johannes Thumshirn
Colin Ian King
Kees Cook
Christoph Hellwig
David S. Miller
David Howells
Cathy Avery
David Gibson
Maurizio Lombardi
Varun Prakash
NeilBrown
Linus Torvalds
James Bottomley
Miguel Bernal Marin
Matthew R. Ochs
Uma Krishnan