aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/serial/mpc52xx_uart.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2010-08-06of/device: Replace struct of_device with struct platform_deviceGrant Likely1-4/+4
of_device is just an alias for platform_device, so remove it entirely. Also replace to_of_device() with to_platform_device() and update comment blocks. This patch was initially generated from the following semantic patch, and then edited by hand to pick up the bits that coccinelle didn't catch. @@ @@ -struct of_device +struct platform_device Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: David S. Miller <davem@davemloft.net>
2010-07-24powerpc/5200: improve uart baud rate calculation (reach high baud rates, better accuracy)Albrecht Dreß1-29/+116
On the MPC5200B, make very high baud rates (e.g. 3 MBaud) accessible and achieve a higher precision for high baud rates in general. This is done by selecting the appropriate prescaler (/4 or /32). As to keep the code clean, the getuartclk method has been dropped, and all calculations are done in a new set_baudrate method. Notes: only "fsl,mpc5200b-psc-uart" compatible devices benefit from these improvements. Tested on a custom 5200B based board, from 110 baud up to 3 MBaud, and with both "fsl,mpc5200b-psc-uart" and "fsl,mpc5200-psc-uart" devices. Also tested on the mpc5121ads board. Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de> [agust: fixed mpc5121 prescaler comment] Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-25Merge remote branch 'origin' into secretlab/next-spiGrant Likely1-7/+8
2010-05-25powerpc/mpc5121: move PSC FIFO memory init to platform codeAnatolij Gustschin1-69/+0
Since PSC could also be used in other modes than UART mode we move PSC FIFO memory initialization from serial driver to common platform code. The initialized FIFO memory slices may not overlap, so the most easy way would be to configure them all at once at init time for all PSC devices. This is now done by this patch. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-22Merge remote branch 'origin' into secretlab/next-devicetreeGrant Likely1-34/+1
Merging in current state of Linus' tree to deal with merge conflicts and build failures in vio.c after merge. Conflicts: drivers/i2c/busses/i2c-cpm.c drivers/i2c/busses/i2c-mpc.c drivers/net/gianfar.c Also fixed up one line in arch/powerpc/kernel/vio.c to use the correct node pointer. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-22of: Remove duplicate fields from of_platform_driverGrant Likely1-3/+4
.name, .match_table and .owner are duplicated in both of_platform_driver and device_driver. This patch is a removes the extra copies from struct of_platform_driver and converts all users to the device_driver members. This patch is a pretty mechanical change. The usage model doesn't change and if any drivers have been missed, or if anything has been fixed up incorrectly, then it will fail with a compile time error, and the fixup will be trivial. This patch looks big and scary because it touches so many files, but it should be pretty safe. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sean MacLennan <smaclennan@pikatech.com>
2010-05-18of: Always use 'struct device.of_node' to get device node pointer.Grant Likely1-4/+4
The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-13serial: mpc52xx_uart: fix null pointer dereferenceAnatolij Gustschin1-1/+1
Commit 6acc6833510db8f72b5ef343296d97480555fda9 introduced NULL pointer dereference and kernel crash on ppc32 machines while booting. Fix this bug now. Reported-by: Leonardo Chiquitto <leonardo.lists@gmail.com> Tested-by: Leonardo Chiquitto <leonardo.lists@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-28serial/mpc52xx_uart: Drop outdated commentsWolfram Sang1-33/+0
Most things mentioned are either obsolete (platform-support) or wrong (device numbering, DCD spport) these days. The remaining rest is obvious. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-16serial: mpc52xx_uart: re-enable mpc5121 PSC UART supportAnatolij Gustschin1-15/+236
Currently the support for MPC5121 PSC UART in the mpc52xx_uart driver is broken (only console pre-initialized by the bootloader works). Re-enable it now by providing MPC5121 specific ops for PSCx clock activation, FIFO controller init/uninit and MPC5121 PSC FIFO shared interrupt handling functions. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEMJulia Lawall1-1/+1
As in the commit 9b4a1617772d6d5ab5eeda0cd95302fae119e359, use UPIO_MEM rather than SERIAL_IO_MEM. Both have the same value. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @has_sc@ @@ #include <linux/serial_core.h> @depends on has_sc@ @@ - SERIAL_IO_MEM + UPIO_MEM // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-09-19serial: kill off uart_infoAlan Cox1-2/+2
We moved this into uart_state, now move the fields out of the separate structure and kill it off. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-17powerpc/5xxx: Add common mpc5xxx_get_bus_frequency() functionWolfgang Denk1-3/+2
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency, while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different clock names (IPS vs. IPB) the code was identical. Use common code for both processor families. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-05-29drivers/serial/mpc52xx_uart.c: fix array overindexing checkRoel Kluin1-1/+1
The check for an overindexing of mpc52xx_uart_{ports,nodes} has an off-by-one. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-04powerpc/5200: Don't specify IRQF_SHARED in PSC UART driverGrant Likely1-1/+1
The MPC5200 PSC device is wired up to a dedicated interrupt line which is never shared. This patch removes the IRQF_SHARED flag from the request_irq() call which eliminates the "IRQF_DISABLED is not guaranteed on shared IRQs" warning message from the console output. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
2009-02-03powerpc/5200: Stop using device_type and port-number propertiesGrant Likely1-28/+10
There is no reason for the PSC UART driver or the Ethernet driver to require a device_type property. The compatible value is sufficient to uniquely identify the device. Remove it from the driver. The whole 'port-number' scheme for assigning numbers to PSC uarts was always rather half baked and just adds complexity. Remove it from the driver. After this patch is applied, PSC UART numbers are simply assigned from the order they are found in the device tree (just like all the other devices). Userspace can query sysfs to determine what ttyPSC number is assigned to each PSC instance. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
2008-12-21powerpc/mpc5200: fix error paths in PSC UART probe functionWolfram Sang1-8/+15
- error cases for mapbase and irq were unbundled - mapped irq now gets disposed on error Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-12-21powerpc/mpc5200: add rts/cts handling in PSC UART driverWolfram Sang1-4/+37
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec MPC5200B-IO. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-12-21powerpc/mpc5200: Make PSC UART driver update serial errors countersRené Bürgel1-2/+8
This patch adds the capability to the mpc52xx-uart to report framing errors, parity errors, breaks and overruns to userspace. These values may be requested in userspace by using the ioctl TIOCGICOUNT. Signed-off-by: René Bürgel <r.buergel@unicontrol.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-12-05Fix incorrect use of loose in tty/serial driversNick Andrew1-2/+2
[Folded together as one diff from 3] It should be 'lose', not 'loose'. Signed-off-by: Nick Andrew <nick@nick-andrew.net> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-25serial/mpc52xx_uart: remove code associated with !CONFIG_PPC_MERGEKumar Gala1-180/+1
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore remove the dead code associated with !CONFIG_PPC_MERGE. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-07-20Fix compile errors in SGI console drivers (linux-next tree)Takashi Iwai1-1/+1
The below is the patch to replace blindly all possible places, including Jack's fixes. Signed-off-by: Takashi Iwai <tiwai@suse.de> (Reviewed and checked rather than blindly added) Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-01Fix a potential issue in mpc52xx uart driverAndrew Liu1-0/+2
mpc52xx_uart_int and __uart_put_char both try to acquire the port->lock. Therefore the function sequence of: mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char can potentially trigger a deadlock. To avoid this deadlock a fix similar to that found in the 8250.c serial driver is applied. The deadlock is avoided by releasing the lock before pushing a buffer and reacquiring it when completed. Signed-off-by: Andrew Liu <shengping.liu@windriver.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-29[POWERPC] mpc5200: Fix unterminated of_device_id tableGrant Likely1-1/+1
If CONFIG_PPC_MPC5121 is not set, then the of_device_id table for the mpc5200 serial driver will not get terminated with a NULL entry. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-15serial: fix platform driver hotplug/coldplugKay Sievers1-0/+2
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable serial platform drivers, to re-enable auto loading. NOTE that Kconfig for some of these drivers doesn't allow modular builds, and thus doesn't match the driver source's unload support. Presumably their unload code is buggy and/or weakly tested... [dbrownell@users.sourceforge.net: more drivers, registration fixes] Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-06[POWERPC] mpc52xx: fix compile error introduce when rebasing patchGrant Likely1-25/+14
When rebasing one of the mpc5200 psc UART patches I made a mistake and damaged the patch. This patch fixes the compile failure introduced in commit 25ae3a0739c69425a911925b43213895a9802b98 Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-02-06[POWERPC] mpc512x: Add MPC512x PSC support to MPC52xx psc driverJohn Rigby1-6/+171
Add 512x support using the psc_ops framework established with the previous patch. All 512x PSCs share the same interrupt so add IRQF_SHARED to irq flags. Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-02-06[POWERPC] mpc512x: Factor out 5200 dependencies from 52xx psc driverJohn Rigby1-64/+192
PSC devices are different between the mpc5200 and the mpc5121 this patch localizes the differences in preparation for adding mpc5121 support to the psc uart driver. Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-26[POWERPC] mpc5200: normalize compatible property bindingsGrant Likely1-1/+3
Update MPC5200 drivers to also look for compatible properties in the form "fsl,mpc5200-*" to better conform to open firmware generic names recommended practice as published here: http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html This patch should *not* break compatibility with older device trees which do not use the 'fsl,' prefix. The drivers will still bind against the older names also. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-21[POWERPC] mpc5200: Cleanup checkpatch.pl problems in mpc52xx_uart.cJohn Rigby1-93/+107
In preparation of adding MPC5121 support cleanup some things that checkpatch.pl complains about also some minor fixes suggested by Stephen Rothwell. Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-21[POWERPC] Separate MPC52xx PSC FIFO registers from rest of PSCJohn Rigby1-4/+6
This is in preparation for the addition of MPC512x PSC support. The main difference in the 512x is in the fifo registers. Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-17[POWERPC] Add of_find_matching_node() helper functionGrant Likely1-1/+2
Similar to of_find_compatible_node(), of_find_matching_node() and for_each_matching_node() allow you to iterate over the device tree looking for specific nodes, except that they take of_device_id tables instead of strings. This also moves of_match_node() from driver/of/device.c to driver/of/base.c to colocate it with the of_find_matching_node which depends on it. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-10-14mpc52xx-uart: fix compile warning (format type mismatch)Grant Likely1-4/+4
Trivial compile warning fix Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-09-14[POWERPC] 52xx: Fix mpc52xx_uart_of_assign to use correct indexJohn Rigby1-1/+1
Use idx as index into mpc52xx_uart_nodes instead of i Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-05-07[POWERPC] Don't shutdown TX on mpc5200 serial port if it is a consoleGrant Likely1-2/+3
If the serial port gets shut down, then console output stalls. 9 out of 10 kernel hackers agree, this is a bad thing. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-02[POWERPC] Rename get_property to of_get_property: driversStephen Rothwell1-1/+1
These are all the remaining instances of get_property. Simple rename of get_property to of_get_property. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-17[POWERPC] Dispose irq mapping when done in mpc52xx_serial.cSylvain Munaut1-1/+3
Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-02-13[POWERPC] Fixup mp5200 drivers to match device tree changesGrant Likely1-3/+2
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-01-09[POWERPC] Fix mpc52xx serial driver to work for arch/ppc againGrant Likely1-0/+2
The mpc52xx_uart_of_enumerate() function was added when adding 52xx support to arch/powerpc, but it must not be called for arch/ppc. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-08[PATCH] tty: switch to ktermiosAlan Cox1-2/+2
This is the grungy swap all the occurrences in the right places patch that goes with the updates. At this point we have the same functionality as before (except that sgttyb() returns speeds not zero) and are ready to begin turning new stuff on providing nobody reports lots of bugs If you are a tty driver author converting an out of tree driver the only impact should be termios->ktermios name changes for the speed/property setting functions from your upper layers. If you are implementing your own TCGETS function before then your driver was broken already and its about to get a whole lot more painful for you so please fix it 8) Also fill in c_ispeed/ospeed on init for most devices, although the current code will do this for you anyway but I'd like eventually to lose that extra paranoia [akpm@osdl.org: bluetooth fix] [mp3@de.ibm.com: sclp fix] [mp3@de.ibm.com: warning fix for tty3270] [hugh@veritas.com: fix tty_ioctl powerpc build] [jdike@addtoit.com: uml: fix ->set_termios declaration] Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Martin Peschke <mp3@de.ibm.com> Acked-by: Peter Oberparleiter <oberpar@de.ibm.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-05[POWERPC] Add of_platform_bus support to mpc52xx psc uart driverGrant Likely1-16/+337
Needed to support mpc52xx boards in arch/powerpc. This patch retains the platform_bus support when compiling for arch/ppc, but uses the of_platform bindings for arch/powerpc. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-12-05[POWERPC] typo fix and whitespace cleanup on mpc52xx-uart driverGrant Likely1-59/+57
Single typo fix and whitespace changes. In preparation for heavy changes to this driver when support for arch/powerpc is added. Since the driver will be changing significantly anyway, then may as well take the opportunity to clean it up first. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-10-06Various drivers' irq handlers: kill dead code, needless castsJeff Garzik1-9/+1
- Eliminate casts to/from void* - Eliminate checks for conditions that never occur. These typically fall into two classes: 1) Checking for 'dev_id == NULL', then it is never called with NULL as an argument. 2) Checking for invalid irq number, when the only caller (the system) guarantees the irq handler is called with the proper 'irq' number argument. Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-05IRQ: Maintain regs pointer globally rather than passing to IRQ handlersDavid Howells1-5/+5
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-01[PATCH] ioremap balanced with iounmap for drivers/serial/mpc52xx_uart.cAmol Lad1-1/+10
ioremap must be balanced by an iounmap and failing to do so can result in a memory leak. Signed-off-by: Amol Lad <amol@verismonetworks.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-03Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serialLinus Torvalds1-2/+1
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial: [SERIAL] Ensure 8250_pci quirks are not marked __devinit [SERIAL] Convert fifosize to an unsigned int
2006-07-02[PATCH] irq-flags: serial: Use the new IRQF_ constantsThomas Gleixner1-1/+1
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-02[SERIAL] Convert fifosize to an unsigned intRussell King1-2/+1
Some UARTs have more than 255 bytes of FIFO, which can't be represented by an unsigned char. Change the kernel's internal structure to be an unsigned int, but still export an unsigned char via the TIOCGSERIAL ioctl. If the TIOCSSERIAL ioctl provides a fifo size of 0, assume this means "don't change" otherwise we'll corrupt the larger fifo sizes. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel1-1/+0
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-26[PATCH] devfs: Remove devfs support from the serial subsystemGreg Kroah-Hartman1-1/+0
Also fixes all serial drivers. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.