| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix previous update, bad git merge likely. oops.
Fixes: 39737a313085fa ("soundwire: cadence: update kernel-doc parameter descriptions")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114233124.13888-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Somehow Intel folks were confused, the property is 2x what the mclk
frequency actually is (checked the actual bus frequency with a scope)
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113231129.19049-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If the programming of the dev_number fails due to an IO error, a new
device_number will be assigned, resulting in a leak.
Make sure we only assign a device_number once per Slave device.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113225637.17313-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix cppcheck warning:
drivers/soundwire/cadence_master.c:992:9: style: Variable 'offset' is
assigned a value that is never used. [unreadVariable]
offset += stream->num_out;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
make W=1 reports inconsistencies with parameter descriptions, fix
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.
This patchset adds support to a very basic controller which has been
tested with WCD934x SoundWire controller connected to WSA881x smart
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200113132153.27239-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Before checking for the presence of Device0, we first need to clean-up
the internal state of Slaves that are no longer attached.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When a Slave reports multiple status in the sticky bits, find the
latest configuration from the mirror of the PING frame status and
update the status directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Config only needs to be updated when setting MCP_Config, MCP_Control
and MCP_CmdCtrl to make these register setting effective. When updating
config in master, master will communicate with slave to update status.
Communication will be failed when masters and slaves are in clock stop
state, and this unnecessary config update makes interrupt setting failed.
Tested on Comet Lake with soundwire enabled
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the type of command, device number, register offset and length to
reverse engineer what caused the issue.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
make sure all interrupts status are cleared before enabling interrupt
so that there is no unexpected interrupt triggered.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If somehow we read the interrupt status while the IP is not powered
the result is probably undefined or 0xffffffff. We do know that some
of the bits are reserved and read as zero, so use as a filter to
discard invalid configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Only keep pr_err to flag critical configuration errors that will
typically only happen during system integration.
For errors on prepare/deprepare/enable/disable, the caller can do a
much better job with more information on the DAI and device that
caused the issue.
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200108175438.13121-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The SoundWire DAIs for Intel platform are created in
drivers/soundwire/intel.c, while the communication with the Intel DSP
is all controlled in soc/sof/intel
When the DAI status changes, a callback is used to bridge the gap
between the two subsystems.
The naming of the existing 'config_stream' callback does not map well
with any of ALSA/ASoC concepts. This patch renames it as
'params_stream' to be more self-explanatory.
A new 'free_stream' callback is added in case any resources allocated
in the 'params_stream' stage need to be released. In the SOF
implementation, this is used in the hw_free case to release the DMA
channels over IPC.
These two callbacks now rely on structures which expose the link_id
and alh_stream_id (required by the firmware IPC), instead of a list of
parameters. The 'void *' definitions are changed to use explicit
types, as suggested on alsa-devel during earlier reviews.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current interfaces between ASoC and SoundWire are limited by the
platform_device infrastructure to an init() and exit() (mapped to the
platform driver.probe and .remove)
To help with the platform detection, machine driver selection and
management of power dependencies between DSP and SoundWire IP, the
ASoC side requires:
a) an ACPI scan helper, to report if any devices are exposed in the
DSDT tables, and if any links are disabled by the BIOS.
b) a probe helper that allocates the resources without actually
starting the bus.
c) a startup helper which does start the bus when all power
dependencies are settled.
d) an exit helper to free all resources
e) an interrupt_enable/disable helper, typically invoked after the
startup helper but also used in suspend routines.
This patch moves all required interfaces to sdw_intel.h, mainly to
allow SoundWire and ASoC parts to be merged separately once the header
files are shared between trees.
To avoid compilation issues, the conflicts in intel_init.c are blindly
removed. This would in theory prevent the code from working, but since
there are no users of the Intel Soundwire driver this has no
impact. Functionality will be restored when the removal of platform
devices is complete.
Support for SoundWire + SOF builds will only be provided once all the
required pieces are upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We need the char/misc driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The uniqueID is useful when there are two or more devices of the same
type (identical manufacturer ID, part ID) on the same link.
When there is a single device of a given type on a link, its uniqueID
is irrelevant. It's not uncommon on actual platforms to see variations
of the uniqueID, or differences between devID registers and ACPI _ADR
fields.
This patch suggests a filter on startup to identify 'single' devices
and tag them accordingly. The uniqueID is then not used for the probe,
and the device name omits the uniqueID as well.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Simplify the loop with a helper. The only functionality change is that
we continue the loop even with an ACPI error.
Follow-up patches will build on this change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The previous formula is incorrect for PDI0/1, the mapping is not
linear but has a discontinuity between PDI1 and PDI2.
This change has no effect on PCM PDIs (same mapping).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022232948.17156-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The use of clock stop is not a requirement, the IP can e.g. be
completely power gated and not detect any wakes while in s2idle/deep
sleep.
For now clock-stop is not supported anyways so the control parameter
is always false. This will be revisited when we add clock stop.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Prepare for future PM support and fix error handling by disabling
interrupts as needed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move code to helper for reuse in power management routines
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Provide debugfs capability to kick link and devices into hard-reset
(as defined by MIPI). This capability is really useful when some
devices are no longer responsive and/or to check the software handling
of resynchronization.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Multiple changes squashed in single patch to avoid tick-tock effect
and avoid breaking compilation/bisect
1. Per the hardware documentation, all changes to MCP_CONFIG,
MCP_CONTROL, MCP_CMDCTRL and MCP_PHYCTRL need to be validated with a
self-clearing write to MCP_CONFIG_UPDATE. Add a helper and do the
update when the CONFIG is changed.
2. Move interrupt enable after interrupt handler registration
3. Add a new helper to start the hardware bus reset with maximum duration
to make sure the Slave(s) correctly detect the reset pattern and to
ensure electrical conflicts can be resolved.
4. flush command FIFOs
Better error handling will be provided after interrupt disable is
provided in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
fix cppcheck warning:
[drivers/soundwire/slave.c:145]: (warning) %x in format string (no. 1)
requires 'unsigned int *' but the argument type is 'signed int *'.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022233147.17268-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit df72b7192119 ("soundwire: intel: add missing headers for
cross-compilation") tried to fix cross compilation but erroneously used
wrong header in one of the file. Fix it by using correct io.h header.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: df72b7192119 ("soundwire: intel: add missing headers for cross-compilation")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are two issues, likely copy/paste:
1. Use cdns->pcm.num_in instead of stream_num_in for consistency with
the rest of the code. This was not detected earlier since platforms did
not have input-only PDIs.
2. use the correct offset for bi-dir PDM, based on IN and OUT
PDIs. Again this was not detected since PDM was not supported earlier.
Reported-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PDI number should match dai->id, there is no need to track if a PDI is
allocated or not.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PDI0/1 are reserved for Bulk and filtered out in the existing code.
That leads to endless confusions on whether the index is the raw or
corrected one. In addition we will need support for Bulk at some point
so it's just simpler to expose those PDIs and not use it for now than
try to be smart unless we have to remove the smarts.
This patch requires a topology change to use PDIs starting at offset 2
explicitly.
Note that there is a known discrepancy between hardware documentation
and what ALH stream works in practice, future fixes are likely.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing Linux code uses a 1:1 mapping between ports and PDIs, but
still has an independent allocation of ports and PDIs.
Let's simplify the code and remove the port layer by only using PDIs.
This patch does not change any functionality, just removes unnecessary
code.
This will also allow for further simplifications where the PDIs are
not dynamically allocated but instead described in a topology file.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We will create dai widget in SOF.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There is no reason to reserve a range of DAI IDs for SoundWire. This
is not scalable and it's better to let the ASoC core allocate the
dai->id when registering a component.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is not needed and may generate unmet dependencies when
COMPILE_TEST is used for SOF.
ACPI is required, and should be tested when selecting this option.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916185739.32184-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
readl/writel and ioread32 are used without the relevant headers, fix.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916185739.32184-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Now devicetree is supported for probing soundwire as well.
On platforms built with !ACPI !OF (ie s390x) the device still cannot be
probed and gives a build warning.
Cc: stable@vger.kernel.org
Fixes: a2e484585ad3 ("soundwire: core: add device tree support for slave devices")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Link: https://lore.kernel.org/r/0b89b4ea16a93f523105c81a2f718b0cd7ec66f2.1570097621.git.msuchanek@suse.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The device cannot be probed on !ACPI and gives this warning:
drivers/soundwire/slave.c:16:12: warning: ‘sdw_slave_add’ defined but
not used [-Wunused-function]
static int sdw_slave_add(struct sdw_bus *bus,
^~~~~~~~~~~~~
Cc: stable@vger.kernel.org
Fixes: 7c3cd189b86d ("soundwire: Add Master registration")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Link: https://lore.kernel.org/r/bd685232ea511251eeb9554172f1524eabf9a46e.1570097621.git.msuchanek@suse.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Pull soundwire updates from Vinod Koul:
"This includes DT support thanks to Srini and more work done by Intel
(Pierre) on improving cadence and intel support.
Summary:
- Add DT bindings and DT support in core
- Add debugfs support for soundwire properties
- Improvements on streaming handling to core
- Improved handling of Cadence module
- More updates and improvements to Intel driver"
* tag 'soundwire-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (30 commits)
soundwire: stream: make stream name a const pointer
soundwire: Add compute_params callback
soundwire: core: add device tree support for slave devices
dt-bindings: soundwire: add slave bindings
soundwire: bus: set initial value to port_status
soundwire: intel: handle disabled links
soundwire: intel: add debugfs register dump
soundwire: cadence_master: add debugfs register dump
soundwire: add debugfs support
soundwire: intel: remove unused variables
soundwire: intel: move shutdown() callback and don't export symbol
soundwire: cadence_master: add kernel parameter to override interrupt mask
soundwire: intel_init: add kernel module parameter to filter out links
soundwire: cadence_master: fix divider setting in clock register
soundwire: cadence_master: make use of mclk_freq property
soundwire: intel: read mclk_freq property from firmware
soundwire: add new mclk_freq field for properties
soundwire: stream: remove unnecessary variable initializations
soundwire: stream: fix disable sequence
soundwire: include mod_devicetable.h to avoid compiling warnings
...
|
|
Make stream name const pointer
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190813083550.5877-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This callback allows masters to compute the bus parameters required.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190813083550.5877-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This patch adds support to parsing device tree based
SoundWire slave devices.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190829163514.11221-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
port_status[port_num] are assigned for each port_num in some if
conditions. So some of the port_status may not be initialized.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190829181135.16049-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On most hardware platforms, SoundWire interfaces are pin-muxed with
other interfaces (typically DMIC or I2S) and the status of each link
needs to be checked at boot time.
For Intel platforms, the BIOS provides a menu to enable/disable the
links separately, and the information is provided to the OS with an
Intel-specific _DSD property. The same capability will be added to
revisions of the MIPI DisCo specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add debugfs file to dump the Intel SoundWire registers
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add debugfs file to dump the Cadence master registers.
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add base debugfs mechanism for SoundWire bus by creating soundwire
root and master-N and slave-x hierarchy.
Also add SDW Slave SCP, DP0 and DP-N register debug file.
Registers not implemented will print as "XX"
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Variables 'nval' and 'i' are no longer used sdw_master_read_intel_prop()
so remove them.
drivers/soundwire/intel.c: In function 'sdw_master_read_intel_prop':
drivers/soundwire/intel.c:829:12: warning: unused variable 'i' [-Wunused-variable]
int nval, i;
^
drivers/soundwire/intel.c:829:6: warning: unused variable 'nval' [-Wunused-variable]
int nval, i;
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 085f4ace103d ("soundwire: intel: read mclk_freq property from firmware")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
All DAI callbacks are in intel.c except for shutdown. Move and remove
export symbol
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The code has a set of defaults which may not be relevant in all cases,
add kernel parameter as a helper - mostly for early board bring-up.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The hardware and ACPI info may report the presence of links that are
not physically enabled (e.g. due to pin-muxing or hardware reworks),
which in turn can result in errors being thrown. This shouldn't be the
case for production devices but will happen a lot on development
devices - even more so when they expose a connector.
Even when the ACPI information is correct, it's useful to be able to
only enable the links that need attention - mostly to filter out
dynamic debug messages.
Add a module parameter to filter out such links, e.g. adding the
following config to a file in /etc/modprobe.d will select the second
and third links only.
options soundwire_intel_init sdw_link_mask=0x6
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The existing code uses an OR operation which would mix the original
divider setting with the new one, resulting in an invalid
configuration that can make codecs hang.
Add the mask definition and use cdns_updatel to update divider
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
Pierre-Louis Bossart
Bard Liao
Srinivas Kandagatla
Rander Wang
Rander Wang
Greg Kroah-Hartman
Vinod Koul
Michal Suchanek
Linus Torvalds