| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In spi_imx_dma_transfer(), when desc_rx = dmaengine_prep_slave_sg()
fails, the context goes to label no_dma and then return. However,
the memory allocated for desc_tx has not been freed yet, which leads
to resource leak.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If SPI device supports DMA mode, but DMA controller is not yet
available due to e.g. a delay in the corresponding kernel module
initialization, retry to initialize SPI driver later on instead of
falling back into PIO only mode.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On SDMA initialization return exactly the same error, which is
reported by dma_request_slave_channel_reason(), it is a preceding
change to defer SPI DMA initialization, if SDMA module is not yet
available.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Limit SPI_LOOP mode to ECSPI controller (iMX.51, iMX53 and i.MX6) only since
there is no support in other families specific code for now.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If controller hold in reset it's not possible to write any
register except CTRL. So all other registers must be updated
only after controller bring out from reset.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Similar to other controller type checks add check function for
IMX51. It includes IMX53 and IMX6.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need to have different watermarks levels since they are the same.
Merge them into one WML parameter.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The overflow may happen due to rescheduling for another task and/or interrupt
if we enable SPI HW before starting RX DMA. So RX DMA enabled first to make
sure data would be read out from FIFO ASAP. TX DMA enabled next to start
filling TX FIFO with new data. And finaly SPI HW enabled to start actual
data transfer.
The risk rise in case of heavy system load and high SPI clock.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Not only TX DMA should be terminated, but RX DMA also. It's required
to avoid accidential DMA memory writes from RX DMA channel and properly
terminate transaction.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Loopback mode can be activated by setting bit LBC (LoopBack
Control) of register ECSPI_TESTREG.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixed problem with setting spi mode 0 or 1 after setting mode 2 or 3
SPI_MODE_0 and SPI_MODE_1 requires clock low when inactive. SPI_MODE_2
and SPI_MODE_3 requires clk high when inactive.
Currently driver can just set bits in fields SCLK_PHA (SPI Clock/Data
Phase Control), SCLK_POL (SPI Clock Polarity Control),
SCLK_CTL (controls the inactive state of SCLK) ans SS_POL (SPI SS
Polarity Select) of ECSPIx_CONFIGREG register.
This patch allows driver to clear corresponding bits in these fields.
Signed-off-by: Andrew Y. Kuksov <qxovxp@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
They are used to decide if the controller can do DMA on a buffer
of a specific length and thus are needed before any transfer is attempted.
This fixes a memory leak where the SPI core uses the drivers can_dma()
callback to determine if a buffer needs to be mapped. As the watermark
levels aren't correct at that point the driver falsely claims to be able to
DMA the buffer when it fact it isn't.
After the transfer has been done the core uses the same callback to
determine if it needs to unmap the buffers. As the driver now correctly
claims to not being able to DMA the buffer the core doesn't attempt to
unmap the buffer which leaves the SGT leaking.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The fourth argument of dmaengine_prep_slave_sg needs to be of the
enumeration type dma_transfer_direction instead of dma_data_direction.
Since the used enumeration values actually stay the same, this is not
an actual issue at runtime.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
return type of wait_for_completion_timeout is unsigned long not int and
always returns >=0 , this patch adds a suitable return variable and
simplifies the return value checking as there is no < 0 case.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For TKT238285 hardware issue which may cause txfifo store data twice can only
be caught on i.mx6dl, we use pio mode instead of DMA mode on i.mx6dl.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The irq number is only used inside the probe function, so there is really no
need to store it in the private structure.
Use a local 'irq' variable to hold the the irq number instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Enable DMA support on i.mx6. The read speed can increase from 600KB/s
to 1.2MB/s on i.mx6q. You can disable or enable dma function in dts.
If not set "dma-names" in dts, spi will use PIO mode. This patch only
validate on i.mx6, not i.mx5, but encourage ones to apply this patch
on i.mx5 since they share the same IP.
Note:
Sometime, there is a weid data in rxfifo after one full tx/rx
transfer finish by DMA on i.mx6dl, so we disable dma functhion on
i.mx6dl.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
Currently, at module removal, one gets the following warnings:
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx])
[<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996300 ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx])
[<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996301 ]---
Since commit 9e556dcc55774c9a1032f32baa0e5cfafede8b70, "spi: spi-imx: only
enable the clocks when we start to transfer a message", clocks are always
disabled except when transmitting messages. There is thus no need to
disable them at module removal.
Fixes: 9e556dcc55774 (spi: spi-imx: only enable the clocks when we start to transfer a message)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Calling init_completion() once is enough.
For the rest of the iterations, call reinit_completion() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Problem:
--------
The problem this patch addresses has the following assumptions about the
SPI bus setup:
- The hardware used to find this is Freescale i.MX537 @ 1200MHz
- The SPI SCLK operate at very low speed, less than 200 kHz
- There are two SPI devices attached to the bus
- Each device uses different GPIO for chipselect
- Each device requires different SCLK signal polarity
The observation of the SCLK and GPIO chipselect lines with a logic analyzer
shows, that the SCLK polarity change does sometimes happen after the GPIO
chipselect is asserted. The SPI slave device reacts on that by counting the
SCLK polarity change as a clock pulse, which disrupts the communication with
the SPI slave device.
Explanation:
------------
We found an interesting correlation, that the maximum delay between the write
into the ECSPIx_CONFIGREG register and the change of SCLK polarity at each
SCLK frequency of 10 kHz, 20 kHz, 50 kHz and 100 kHz is 100 uS, 50 uS, 20 uS
and 10 uS respectively. This lead us to a theory, that at SCLK frequency of
1 Hz, the delay would be 1 S. Therefore, the time it takes for the write to
ECSPIx_CONFIGREG to take effect in the hardware is up to the duration of 1
tick of the SCLK clock.
During this delay period, if the SCLK frequency is too low, the execution of
the spi-imx.c driver can advance so much, that the GPIO chipselect will be
asserted. The GPIO chipselect is asserted almost immediatelly.
Solution:
---------
The solution this patch presents is simple. We calculate the resulting SCLK
clock first by dividing the ECSPI block clock by both dividers that are to be
programmed into the configuration register. Based on the resulting SCLK clock,
we derive the delay it will take for the changes to get really applied. We are
extra careful here so we delay twice as long as we should. Note that the patch
does not create additional overhead at high speeds as the delay will likely be
close to zero there.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-spi@vger.kernel.org
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Huang Shijie <b32955@freescale.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Current code keeps the clocks enabled all the time, it wastes the power
when there is no operaiton on the spi controller.
In order to save the power, this patch adds the two hooks:
spi_imx_prepare_message: enable the clocks for this message
spi_imx_unprepare_message: disable the clocks.
This patch also disables the clocks in the end of the probe.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Many drivers that use bitbang library have a leak on probe error paths.
This is because once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory.
Fix this issue by moving the code taking a reference to master to
spi_bitbang_start(), so spi_bitbang_start() will take a reference to master on
success. With this change, the caller is responsible for calling
spi_bitbang_stop() to decrement the reference and spi_master_put() as
counterpart of spi_alloc_master() to prevent a memory leak.
So now we have below patten for drivers using bitbang library:
probe:
spi_alloc_master -> Init reference count to 1
spi_bitbang_start -> Increment reference count
remove:
spi_bitbang_stop -> Decrement reference count
spi_master_put -> Decrement reference count (reference count reaches 0)
Fixup all users accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Suggested-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Enable auto loading by udev when spi-imx is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
While at it, fix the order of clk_disable_unprepare calls: clk_ipg should be
disabled first, followed by clk_per.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Using devm functions can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
|
|
Fix compilation error due to a typo introduced by commit 24778be20f
("spi: convert drivers to use bits_per_word_mask"). Without this patch
we get the following build errors:
drivers/spi/spi-imx.c: In function ‘spi_imx_setupxfer’:
drivers/spi/spi-imx.c:703:2: warning: no return statement in function returning non-void [-Wreturn-type]
drivers/spi/spi-imx.c: At top level:
drivers/spi/spi-imx.c:705:9: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘->’ token
drivers/spi/spi-imx.c:707:2: error: expected identifier or ‘(’ before ‘return’
drivers/spi/spi-imx.c:708:1: error: expected identifier or ‘(’ before ‘}’ token
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add an entry for MODULE_ALIAS().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
|
|
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
|
|
There are SPI devices which need a SPI clock with active low polarity and
high inactive state.
Add the setting of the inactive state ECSPIx_CONFIGREG:SCLK CTL
according to the clock polarity ECSPIx_CONFIGREG:SCLK POL:
DT without "spi-cpol" = 0 = clock active high polarity = inactive state low
DT with "spi-cpol" = 1 = clock active low polarity = inactive state high
Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
|
|
This prepares *of_device_id.data becoming const. Without this change the
following warning would occur:
drivers/spi/spi-imx.c: In function spi_imx_probe:
drivers/spi/spi-imx.c:814:24: warning: assignment discards const qualifier from pointer target type [enabled by default]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
Use gpio_is_valid() to replace "gpio >= 0" or "gpio < 0".
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
Gao Pan
Anton Bondarenko
Fabio Estevam
Andrew Y. Kuksov
Sascha Hauer
Krzysztof Kozlowski
Mark Brown
Lucas Stach
Stefan Agner
Nicholas Mc Guire
Robin Gong
Wolfram Sang
Mark Brown
Philippe De Muyter
Alexander Shiyan
Axel Lin
Paul Gortmaker
Marek Vasut
Huang Shijie
Niels de Vos
Sachin Kamat
Stephen Warren
Jingoo Han
Grant Likely
Linus Torvalds
Knut Wohlrab
Arnd Bergmann
Uwe Kleine-König
Hui Wang