aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/spi (follow)
AgeCommit message (Collapse)AuthorFilesLines
2016-02-12Merge remote-tracking branches 'spi/fix/atmel', 'spi/fix/bcm2835aux', 'spi/fix/fsl-espi', 'spi/fix/imx', 'spi/fix/loopback' and 'spi/fix/omap2-mcspi' into spi-linusMark Brown6-7/+14
2016-02-12spi: omap2-mcspi: Fix PM regression with deferred probe for pm_runtime_reinitTony Lindgren1-0/+3
Commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe error and driver unbind") introduced pm_runtime_reinit() that is used to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting down the device after a failed probe. However, for drivers using pm_runtime_use_autosuspend() this can cause a state where suspend callback is never called after -EPROBE_DEFER. On the following device driver probe, hardware state is different from the PM runtime state causing omap_device to produce the following error: omap_device_enable() called from invalid state 1 And with omap_device and omap hardware being picky for PM, this will block any deeper idle states in hardware. The solution is to fix the drivers to follow the PM runtime documentation: 1. For sections of code that needs the device disabled, use pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has been set. 2. For driver exit code, use pm_runtime_dont_use_autosuspend() before pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been set. Fixes: 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe error and driver unbind") Cc: linux-spi@vger.kernel.org Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Mark Brown <broonie@kernel.org> Cc: Nishanth Menon <nm@ti.com> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-10spi: bcm2835aux: fix bitmask definesStephan Olbrich1-2/+2
The bitmasks for txempty and idle interrupts were interchanged. Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-28spi: atmel: fix gpio chip-select in case of non-DT platformCyrille Pitchen1-0/+1
The non-DT platform that uses this driver (actually the AVR32) was taking a bad branch for determining if the IP would use gpio for CS. Adding the presence of DT as a condition fixes this issue. Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller") Reported-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> [nicolas.ferre@atmel.com: extract from ml discussion] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
2016-01-22spi/fsl-espi: Correct the maximum transaction lengthHou Zhiqiang1-2/+2
The maximum length during one transcation is 64KiB. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-22spi: imx: fix spi resource leak with dma transferGao Pan1-3/+5
In spi_imx_dma_transfer(), when desc_rx = dmaengine_prep_slave_sg() fails, the context goes to label no_dma and then return. However, the memory allocated for desc_tx has not been freed yet, which leads to resource leak. Signed-off-by: Gao Pan <pandy.gao@nxp.com> Reviewed-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-15Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds1-1/+1
Pull powerpc updates from Michael Ellerman: "Core: - Ground work for the new Power9 MMU from Aneesh Kumar K.V - Optimise FP/VMX/VSX context switching from Anton Blanchard Misc: - Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan - Allow wrapper to work on non-english system from Laurent Vivier - Add rN aliases to the pt_regs_offset table from Rashmica Gupta - Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt - Include KVM guest test in all interrupt vectors from Paul Mackerras - Fix DSCR inheritance over fork() from Anton Blanchard - Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng - Print MSR TM bits in oops messages from Michael Neuling - Add TM signal return & invalid stack selftests from Michael Neuling - Limit EPOW reset event warnings from Vipin K Parashar - Remove the Cell QPACE code from Rashmica Gupta - Append linux_banner to exception information in xmon from Rashmica Gupta - Add selftest to check if VSRs are corrupted from Rashmica Gupta - Remove broken GregorianDay() from Daniel Axtens - Import Anton's context_switch2 benchmark into selftests from Michael Ellerman - Add selftest script to test HMI functionality from Daniel Axtens - Remove obsolete OPAL v2 support from Stewart Smith - Make enter_rtas() private from Michael Ellerman - PPR exception cleanups from Michael Ellerman - Add page soft dirty tracking from Laurent Dufour - Add support for Nvlink NPUs from Alistair Popple - Add support for kexec on 476fpe from Alistair Popple - Enable kernel CPU dlpar from sysfs from Nathan Fontenot - Copy only required pieces of the mm_context_t to the paca from Michael Neuling - Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey - Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt - Add HWCAP bits for Power9 from Michael Ellerman - Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V - Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins - scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand - Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand cxl: - cxl: Fix possible idr warning when contexts are released from Vaibhav Jain - cxl: use correct operator when writing pcie config space values from Andrew Donnellan - cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain - cxl: fix build for GCC 4.6.x from Brian Norris - cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris - cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan Freescale: - Freescale updates from Scott: Highlights include moving QE code out of arch/powerpc (to be shared with arm), device tree updates, and minor fixes" * tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits) powerpc/module: Handle R_PPC64_ENTRY relocations scripts/recordmcount.pl: support data in text section on powerpc powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff powerpc/mm: Fix _PAGE_PTE breaking swapoff cxl: Enable PCI device ID for future IBM CXL adapter cxl: use -Werror only with CONFIG_PPC_WERROR cxl: fix build for GCC 4.6.x powerpc: Add HWCAP bits for Power9 powerpc/powernv: Reserve PE#0 on NPU powerpc/powernv: Change NPU PE# assignment powerpc/powernv: Fix update of NVLink DMA mask powerpc/powernv: Remove misleading comment in pci.c powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing powerpc: Fix build break due to paca mm_context_t changes cxl: Fix DSI misses when the context owning task exits MAINTAINERS: Update Scott Wood's e-mail address powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery() powerpc: Fix style of self-test config prompts powerpc/powernv: Only delay opal_rtc_read() retry when necessary ...
2016-01-15spi: fix counting in spi-loopback-test codeArnd Bergmann1-0/+1
These variables are always used uninitialized: drivers/spi/spi-loopback-test.c: In function 'spi_test_run_iter': drivers/spi/spi-loopback-test.c:768:17: warning: 'rx_count' may be used uninitialized in this function [-Wmaybe-uninitialized] drivers/spi/spi-loopback-test.c:762:17: warning: 'tx_count' may be used uninitialized in this function [-Wmaybe-uninitialized] Adding an explicit initialization seems to be the only workable solution here, to make the code behave correctly and build without warning. Fixes: 84e0c4e5e2c4 ("spi: add loopback test driver to allow for spi_master regression tests") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-13Merge tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spiLinus Torvalds23-177/+1387
Pull spi updates from Mark Brown: "A quiet release for SPI, not even many driver updates: - Add a dummy loopback driver for use in exercising framework features during development. - Move the test utilities to tools/ and add support for transferring data to and from a file instead of stdin and stdout to spidev_test. - Support for Mediatek MT2701 and Renesas AG5 deices" * tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits) spi: loopback: fix typo in MODULE_PARM_DESC spi: sun4i: Prevent chip-select from being activated twice before a transfer spi: loopback-test: spi_check_rx_ranges can get always done spi: loopback-test: rename method spi_test_fill_tx to spi_test_fill_pattern spi: loopback-test: write rx pattern also when running without tx_buf spi: fsl-espi: expose maximum transfer size limit spi: expose master transfer size limitation. spi: zynq: use to_platform_device() spi: cadence: use to_platform_device() spi: mediatek: Add spi support for mt2701 IC spi: mediatek: merge all identical compat to mtk_common_compat spi: mtk: Add bindings for mediatek MT2701 soc platform spi: mediatek: Prevent overflows in FIFO transfers spi: s3c64xx: Remove unused platform_device_id entries spi: use to_spi_device spi: dw: Use SPI_TMOD_TR rather than magic const 0 to set tmode spi: imx: defer spi initialization, if DMA engine is spi: imx: return error from dma channel request spi: imx: enable loopback only for ECSPI controller family spi: imx: fix loopback mode setup after controller reset ...
2016-01-11Merge remote-tracking branches 'spi/topic/sun4i', 'spi/topic/topcliff-pch' and 'spi/topic/zynq' into spi-nextMark Brown4-15/+11
2016-01-11Merge remote-tracking branches 'spi/topic/overlay', 'spi/topic/pxa2xx', 'spi/topic/s3c64xx', 'spi/topic/sh-msiof' and 'spi/topic/spidev' into spi-nextMark Brown4-30/+37
2016-01-11Merge remote-tracking branches 'spi/topic/lm70llp', 'spi/topic/loopback', 'spi/topic/mtk' and 'spi/topic/omap2-mcspi' into spi-nextMark Brown7-45/+1216
2016-01-11Merge remote-tracking branches 'spi/topic/dw', 'spi/topic/dw-mid', 'spi/topic/fsl-espi' and 'spi/topic/imx' into spi-nextMark Brown5-37/+76
2016-01-11Merge remote-tracking branches 'spi/topic/bcm63xx', 'spi/topic/butterfly', 'spi/topic/cadence' and 'spi/topic/davinci' into spi-nextMark Brown4-35/+25
2016-01-11Merge remote-tracking branch 'spi/topic/sunxi' into spi-nextMark Brown1-3/+3
2016-01-11Merge remote-tracking branch 'spi/topic/core' into spi-nextMark Brown1-2/+1
2016-01-11Merge remote-tracking branch 'spi/fix/mtk' into spi-linusMark Brown1-10/+18
2016-01-08spi: loopback: fix typo in MODULE_PARM_DESCDan Carpenter1-1/+1
There should be an 's' on "dump_message" so it matches the module_param. Fixes: 84e0c4e5e2c4 ('spi: add loopback test driver to allow for spi_master regression tests') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-07spi: sun4i: Prevent chip-select from being activated twice before a transferMarcus Weseloh1-3/+3
The SPI core calls set_cs before a transfer, but the SUN4I_CTL_CS_MANUAL flag is only set in transfer_one. This leads to the following pattern on the chip-select line (with runtime power-management on every transfer, without it only on the first one): activate, deactivate, activate, transfer, deactivate Moving the configuration of the SUN4I_CTL_CS_MANUAL flag from transfer_one to set_cs removes the double activation. Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: loopback-test: spi_check_rx_ranges can get always doneMartin Sperl1-5/+14
The spi_check_rx_ranges can always get executed independent of if we have a real loopback situation. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: loopback-test: rename method spi_test_fill_tx to spi_test_fill_patternMartin Sperl1-3/+4
Rename method spi_test_fill_tx to spi_test_fill_pattern to better describe what it does. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: loopback-test: write rx pattern also when running without tx_bufMartin Sperl1-4/+4
Currently the rx_buf does not get set with the SPI_TEST_PATTERN_UNWRITTEN when tx_buf == NULL in the transfer. Reorder code so that it gets done also under this specific condition. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: fsl-espi: expose maximum transfer size limitMichal Suchanek1-0/+6
The fsl-espi hardware can trasfer at most 64K data so report teh limitation. Based on patch by Heiner Kallweit <hkallweit1@gmail.com> CC: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Michal Suchanek <hramrach@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: zynq: use to_platform_device()Geliang Tang1-6/+2
Use to_platform_device() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-05spi: cadence: use to_platform_device()Geliang Tang1-4/+2
Use to_platform_device() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-01ACPI / spi: attach GPIO IRQ from ACPI description to SPI deviceChristophe RICARD1-0/+3
spi->irq was ignoring GpioInt property setting it to -1. acpi_dev_gpio_irq_get returns and configure the slave IRQ according to the ACPI slave node description. It is now inline with devicetree behavior. Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-31spi: mediatek: Add spi support for mt2701 ICLeilk Liu1-0/+3
This patch adds spi support for mt2701 IC. Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-31spi: mediatek: merge all identical compat to mtk_common_compatLeilk Liu1-5/+10
This patch merge all identical compat into on mtk_common_compat and used for all compatible soc. Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-30spi: mediatek: Prevent overflows in FIFO transfersNicolas Boichat1-10/+18
In the case where transfer length is not a multiple of 4, KASAN reports 2 out-of-bounds memory accesses: - mtk_spi_interrupt: ioread32_rep writes past the end of trans->rx_buf. - mtk_spi_fifo_transfer: iowrite32_rep reads past the end of xfer->tx_buf. Fix this by using memcpy on the remainder of the bytes. Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-30spi: s3c64xx: Remove unused platform_device_id entriesSylwester Nawrocki1-6/+0
s5pv210 and exynos4 are now DT only platforms hence these entries can now be safely removed from the match table. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-23spi: use to_spi_deviceGeliang Tang1-2/+1
Use to_spi_device() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-23spi: dw: Use SPI_TMOD_TR rather than magic const 0 to set tmodeJisheng Zhang1-1/+1
The TMODE available value is well defined and documented in the header file. Use it and remove the comment. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-22QE: Move QE from arch/powerpc to drivers/socZhao Qiang1-1/+1
ls1 has qe and ls1 has arm cpu. move qe from arch/powerpc to drivers/soc/fsl to adapt to powerpc and arm Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-16Merge remote-tracking branches 'spi/fix/dspi' and 'spi/fix/spidev' into spi-linusMark Brown2-7/+7
2015-12-16Merge remote-tracking branch 'spi/fix/core' into spi-linusMark Brown1-1/+1
2015-12-16spi: fix parent-device reference leakJohan Hovold1-1/+1
Fix parent-device reference leak due to SPI-core taking an unnecessary reference to the parent when allocating the master structure, a reference that was never released. Note that driver core takes its own reference to the parent when the master device is registered. Fixes: 49dce689ad4e ("spi doesn't need class_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
2015-12-16spi: spidev: Hold spi_lock over all defererences of spi in release()Mark Brown1-1/+1
We use the spi_lock spinlock to protect against races between the device being removed and file operations on the spidev. This means that in the removal path all references to the device need to be done under lock as in removal we dropping references to the device. Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-15spi: imx: defer spi initialization, if DMA engine isAnton Bondarenko1-0/+3
If SPI device supports DMA mode, but DMA controller is not yet available due to e.g. a delay in the corresponding kernel module initialization, retry to initialize SPI driver later on instead of falling back into PIO only mode. Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-15spi: imx: return error from dma channel requestAnton Bondarenko1-11/+16
On SDMA initialization return exactly the same error, which is reported by dma_request_slave_channel_reason(), it is a preceding change to defer SPI DMA initialization, if SDMA module is not yet available. Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-15spi: imx: enable loopback only for ECSPI controller familyAnton Bondarenko1-5/+6
Limit SPI_LOOP mode to ECSPI controller (iMX.51, iMX53 and i.MX6) only since there is no support in other families specific code for now. Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-15spi: imx: fix loopback mode setup after controller resetAnton Bondarenko1-1/+3
If controller hold in reset it's not possible to write any register except CTRL. So all other registers must be updated only after controller bring out from reset. Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-13spi: loopback: added additional non-power of 2 transfer lengthesMartin Sperl1-3/+4
Added additional transfer length to test that are not a power of 2. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-13spi: loopback: match configuration of test to descriptionMartin Sperl1-1/+1
The test "two tx+rx transfers - alter second" actually modifies the first not the second transfer, which - in conjunction with testing the read data - results also in overwriting data read earlier. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-13spi: loopback: fix printk format issues with size_tMartin Sperl1-3/+3
Fixes the reported printk format issues reported by kbuild-test-robot. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12spi: add spi-loopback-test to build frameworkMartin Sperl2-0/+10
adding the spi-loopback-test module to Kconfig and Makefile Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12spi: add loopback test driver to allow for spi_master regression testsMartin Sperl2-0/+1130
This driver is submitting lots of distinct spi-messages messages with all kinds of alignments and length pattern. Also distinct kinds of transfer pattern tests are implemented (rx, tx, rx/tx, tx+tx, tx+rx,...) Right now on a raspberry pi 752 distinct spi_messages are executed in 13 different scenarios. Configuration of additional test-pattern is easy, so that when new bugs in drivers get detected the relevant transfer pattern can also get added to the test framework, so that such situations are detected in other drivers as well. The idea behind this driver is to make it possible to also detect regressions in spi_master implementations when changes occur. Potentially these tests could get executed automatically in a test-server-farm. Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12spi: davinci: use dev_err() for error reportingSekhar Nori1-7/+7
Use dev_err() for reporting errors rather than dev_dbg(). Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12spi: davinci: fix spurious i/o errorSekhar Nori1-1/+2
davinci_spi_bufs() uses wait_for_completion_interruptible() without bothering to handle -ERESTARTSYS. Due to this, sometime, it returns prematurely when a signal is received. Since the return value is never checked, userspace eventually receives a spurious -EIO. To fix this, use un-interruptible wait_for_completion_timeout(). Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12spi-fsl-dspi: Fix CTAR Register accessBhuvanchandra DV1-6/+6
DSPI instances in Vybrid have a different amount of chip selects and CTARs (Clock and transfer Attributes Register). In case of DSPI1 we only have 2 CTAR registers and 4 CS. In present driver implementation CTAR offset is derived from CS instance which will lead to out of bound access if chip select instance is greater than CTAR register instance, hence use single CTAR0 register for all CS instances. Since we write the CTAR register anyway before each access, there is no value in using the additional CTAR registers. Also one should not program a value in CTAS for a CTAR register that is not present, hence configure CTAS to use CTAR0. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-07spi: lm70llp: remove printkSudip Mukherjee1-4/+4
Using pr_* macros are more prefferable than using printk. Start using pr_* family of macros and define pr_fmt to be used with it. While at it remove DRVNAME from an existing pr_info() as the name is now being printed by pr_fmt. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.