| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After a review of the bindings 'clocks', 'resets' and 'phys' must
be moved into root port child nodes. Hence, move all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210607120153.24989-5-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pcie node is being overlayed in 'gbpc1.dts' file requesting three
gpio reset pins for each pcie port. Gnubee only needs general
gpio 19 to properly reset and make all of them work. This pin
is already requested in the general 'mt7621.dtsi' file as well
as is the pinctrl pins. So we only need to enable the node
in the overlay and all the other stuff can be safely deleted.
Also, pin 8 is being requested for gpio-leds node and there
was an error on boot before this changes because of pin was
already assigned (EBUSY):
leds-gpio: probe of gpio-leds failed with error -16
With this changes this error has disappear and the board is
properly booting without any other regression.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210604063031.13599-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MT7621 SoC clock driver has already mainlined in
'commit 48df7a26f470 ("clk: ralink: add clock driver for mt7621 SoC")'
Hence we can use the clock in pcie phy nodes to
be able to get it from there in driver code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210514112820.32499-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Property 'bus-range' when values are the default are
not necessary to be defined. Hence, remove all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Both 'memc' and 'sysc' nodes are not using 'syscon'
as a node string which is the standard one to be used.
Update both of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DT 'ethsys' node is being configured as a syscon
to get access to reset and other registers in the
'mediateķ,mt7621-eth' driver. Since the 'sysc' is also
a syscon, provides the clock and also is virtually
mapped from the same physical address 0x1e000000 we
can just use 'sysc' as the phandle for the syscon in
the ethernet node. Compatible string 'mediatek,mt7621-ethsys'
of the node is not being used anywhere inside the kernel
so, this node can be safely removed.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Custom function for 'map_irq' was introduced in
commit fab6710e4c51 ("staging: mt7621-pci: fix PCIe interrupt mapping")
This is not really necessary and code has been fixed to avoid
custom configuration of the virtual bridges and make possible
to properly map the root ports interrupts using this standard
properties. Hence properly update device tree accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-10-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Vendor listed for mediatek in kernel vendor file 'vendor-prefixes.yaml'
contains 'mediatek' as a valid vendor string. Some nodes in the device
tree are using an invalid vendor string vfor 'mtk' instead. Fix all of
them in dts file. Update also ralink mt7621 related code to properly
match new strings. Even there are used in the device tree there are
some strings that are not referred anywhere but have been also updated
with new vendor name. These are 'mtk,mt7621-wdt', 'mtk,mt7621-nand',
'mtk,mt7621-mc', and 'mtk,mt7621-cpc'.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210410055059.13518-4-sergio.paracuellos@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Clocks for SoC mt7621 have been properly integrated so there is
no need to declare fixed clocks at all in the device tree. Remove
all of them, add new device tree nodes for mt7621-clk and update
the rest of the nodes to use them.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210410055059.13518-3-sergio.paracuellos@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This was for OpenWrt's swconfig driver, which never made it upstream,
and was also superseded by MT7530 DSA driver.
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20210108025155.31556-1-dqfext@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the binding documentation pinctrl related nodes
must use '-pins$' and ''^(.*-)?pinmux$'' as names. Change all
to properly match them. Also default state is for consumer
nodes and shall be removed from here.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210104150651.32083-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the gpio DT node has the 'gpio-ranges' property, the range will be
added by the gpio core and doesn't need to be added by the pinctrl
driver.
By having the gpio-ranges property, we can map every pin between
gpio node and pinctrl node and we can stop using the deprecated
pinctrl_add_gpio_range() function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20201206105333.18428-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MT7621 has three assigned interrupts for the pcie. This
interrupts should properly being mapped taking into account
which devices are finally connected in which bus according
to link status. So the irq mappings should be as follows
according to link status (three bits indicating which devices
are link up):
* For PCIe Bus 1 slot 0:
- status = 0x2 || status = 0x6 => IRQ = pcie1_irq (24).
- status = 0x4 => IRQ = pcie2_irq (25).
- default => IRQ = pcie0_irq (23).
* For PCIe Bus 2 slot 0:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 2 slot 1:
- status = 0x5 || status = 0x6 => IRQ = pcie2_irq (25).
- default => IRQ = pcie1_irq (24).
* For PCIe Bus 3 any slot:
- default => IRQ = pcie2_irq (25).
Because of this, the function 'of_irq_parse_and_map_pci' cannot
be used and we need to change device tree information from using
the 'interrupt-map' and 'interrupt-map-mask' properties into an
'interrupts' property to be able to get irq information from the
ports using the 'platform_get_irq' and storing an 'irq-map' into
the pcie driver data node to properly map correct irq using a
new 'mt7621_map_irq' function where this map will be read and the
correct irq returned.
Fixes: 46d093124df4 ("staging: mt7621-pci: improve interrupt mapping")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200413055942.2714-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are three pins that can be used for reset gpios.
As mentioned in the application note, there are two
possible way of wiring pcie reset:
* connect gpio19 to all pcie reset pins
* connect gpio19 to pcie0 reset and pick two other
gpios for pcie1 and pcie2
gpio7 and gpio8 may not be used as pcie reset and are
vendor specific. Hence, maintain common mt7621.dtsi with
only gpio19 which is common and make an overlay for gnubee
board which uses all gpio's as resets for pcie. After this
changes release gpios in driver code is not needed anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200321072650.7784-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This soc has only two real pcie phys one of them
having a different register to enable and disable it.
Change this to have only two dt nodes for the phys and
use 'phy-cells' properly to say if the phy has dual ports.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Properly set pins for group pcie as 'gpio' function and declare
gpio's in the pci node to make reset stuff properly functional.
Delete no more needed general reset and previous pers gpio which
is now being used in 'reset-gpios' property.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200313200913.24321-4-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200109080120.362110-1-gch981213@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mt7621 has two network interfaces, one that connects to an
internal switch, and one that can connect to either that switch
or an external phy, or possibly an internal phy.
The Gnubee-PC2 has an external phy for use with the second interface.
This patch add some support for the second interface to mt7621.dtsi
and add a gbpc2.dts which makes use of this. This allows the second
interface to be used.
I don't fully understand how to configure this interface - the
documentation is thin - so there could well be room for improvement
here.
Signed-off-by: NeilBrown <neil@brown.name>
Link: https://lore.kernel.org/r/156194178766.1430.12784163026696670896.stgit@noble.brown
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The mtk-sd driver has been updated to support
the IP in the mt7621, so update our configuration
to work with it.
Signed-off-by: NeilBrown <neil@brown.name>
Link: https://lore.kernel.org/r/156194178761.1430.1625105851941268306.stgit@noble.brown
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver has been changed to use perts gpio reset instead of
perst builtin behaviour. Update device tree accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"git diff" says:
\ No newline at end of file
after modifying the files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few remaining drivers/staging/*/Makefile files that do not
have SPDX identifiers in them. Add the correct GPL-2.0 identifier to
them to make scanning tools happy.
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few remaining drivers/staging/*/Kconfig files that do not
have SPDX identifiers in them. Add the correct GPL-2.0 identifier to
them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If each phy port doesn't have its own resources, then we don't need
child nodes. Handle it using #phy-cells to 1 for both phy's.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ethernet in mt7621 is now supported by
drivers/net/ethernet/mediatek/
which provides support for the integrated switch through DSA.
This requires some devicetree changes, and particularly allows
a board dts to identify which switch ports are present.
The second CPU interface - gmac1 - doesn't work yet, so the device
tree information may not be correct. The phy (which is present on the
gnubee-pc2) can negotiate and report connection speed etc, but no
traffic flows.
The gnubee-pc1 has two network ports which are 'black' and 'blue'.
There are connected to switch ports 0 and 4 respectively.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add general pci reset line to pcie bindings to use reset_control properly
in driver code.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Both pci-phy0 and pci-phy1 are using bad addresses to search
for its registers. Use proper register values.
Fixes: 06184ba5a33a: staging: mt7621-dts: add pci-phy related bindings to board's device tree
Reported-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
New driver for pci phy has been added, as well as. pci driver has been
changed to use kernel's generic PHY API. Add related PCI PHY bindings
accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pinctrl generic functions looks for standard property 'groups' in DT to get
data and use in the driver. Change all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device-tree checking code sees node names "i2c" and "spi" in the
pinctrl definition and thinks these are defining i2c or spi devices,
and complains that they look wrong.
So add a '0' to the end of each name (much like "uart" and "rgmii"
have numbers at the end) to avoid the warning.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit bb276262e88d ("mtd: spi-nor: only apply reset hacks to
broken hardware"), we need to mark the spi-nor as "broken" for reboot
to work.
Note that nothing is actually broken here. The hardware-watchdog in
the SoC isn't wired in a way that works, but then the board doesn't
claim to support a hardware watchdog - and the SPI certain isn't
"broken".
This causes an annoying warning on every boot, but that is better than
failing on ever reboot.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sysctl register are already claimed by palmbus, so
pci fails to claim it. Remove registers accordly from DT
bindings.
Fixes: 624c5227ed0a: staging: mt7621-dts: add sysctl registers base address to pcie
Reported-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Tested-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing system control registers address in pcie node of
the device tree.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pcie node of the device tree only contains registers
for the host-bridge and pcie port 0. Add the pcie port 1
and pcie port 2 also.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Tested-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to documentation 'pinctrl-bindings.txt' bindings 'group'
and 'function' can be used directly. So replace all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Banks shouldn't be defined in DT if number of resources
per bank is not variable. We actually know that this SoC
has three banks so take that into account in order to don't
overspecify the device tree. Device tree will only have one
node making it simple. Update device tree, binding doc and
code accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This currently fixes the remaining dtb warnings:
Node /pcie@1e140000/pcie0 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie1 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie2 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie0 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
device_type was removed since according to documentation, it's deprecated
for pci(e) devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that gpio-interrupts work correctly, we
can use gpio-keys instead of gpio-keys-polled
for the single push-button on the gbpc-1.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The MT7621 documentation says that the sys clock - also known
as OCP clock for the Open Core Protocol - can be configured to
1/3 or 1/4 of the CPU clock.
Testing on my hardware, using the fact that the SPI clock is
based on the OCP clock and measuring transfer rates, shows
a clock of a little over 200MHz with a CPU clock of 900MHz.
So assume 1/4 is the default.
Also, the nor-flash in the gbpc1 is documented as accepting 50MHz
for request requests, and higher for other requests. So set
maximum to 50MHz.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Most gpio chips have two cells for interrupts and this should be also.
Set this property in the device tree accordly fixing this up. In order
to make this working properly the xlate function for the irq_domain must
be updated to use the 'irq_domain_xlate_twocell' one in the driver.
One more minimal change is needed two refer gpio's interrupt-parent from
other nodes which is to add new 'gpio' label in the device tree.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to let other devices reference the GPIO interrupts
if necessary properties 'interrupt-controller' and
'#interrupt-cells' becomes necessary. Add both of them to
complete gpio device tree node.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The GPIO controller of mt7621 can receive interrupts on any
of the GPIOs, either edge or level. It then interrupts the CPU using
GIC INT12. Update device tree accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Gpio driver for mt7621 is using 'mtk' as binding but in the kernel
is already defined one for this maker which is 'mediatek'. Update
device tree to use the correct one.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The GNUBEE has 32MB flash, so set partitions accordingly.
Also remove "m25p,chunked-io" which isn't documented or
used anywhere (outside of freewrt).
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.
The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace spaces with tabs in indentation.
Issue found with checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add device tree source for mt7621 and gnubee1 to
make testing easier.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Sergio Paracuellos
DENG Qingfang
Chuanhong Guo
NeilBrown
Geert Uytterhoeven
Greg Kroah-Hartman
Rosen Penev
Nishka Dasgupta