| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The variable tmp is being masked with a bitmask and the value is being
written to port base + 0x3c. However, the masked value is being written
back to tmp and tmp is never used after this. The assignmentment is
redundant, replace the &= operator with just &.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewesd-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211205232822.110099-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae5b ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d44f ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c624 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.
Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9bd3 ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit f45709df7731 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df7731 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the StarFive JH7100 RISC-V SoC the UART core clocks can't be set to
exactly 16 * 115200Hz and many other common bitrates. Trying this will
only result in a higher input clock, but low enough that the UART's
internal divisor can't come close enough to the baud rate target.
So rather than try to set the input clock it's better to skip the
clk_set_rate call and rely solely on the UART's internal divisor.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211116150119.2171-15-kernel@esmil.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jing Yao <yao.jing2@zte.com.cn>
Link: https://lore.kernel.org/r/20211104114754.30983-1-yao.jing2@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ->exit() callback is checked for presence anyway,
no need to have an empty stub.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211026133452.61657-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace pci_quatech_amcc() with generic pci_match_id().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211026133452.61657-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI subsystem provides convenient shortcut macros for message printing.
Use those macros instead of dev_*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'else' keyword is not needed when previous conditional branch returns
to the upper layer. Get rid of redundant 'else' keyword in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The loop can be refactored by using ARRAY_SIZE() instead of NULL terminator.
This reduces code base and makes it easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver was updating the port uartclk before setting the new rate in
an attempt to avoid having the clock notifier redundantly update the
divisors.
The set_termios() callback is however called under the termios semaphore
and tty-port mutex so the worker scheduled by the clock notifier will
block in serial8250_update_uartclk() until the uartclk and divisors have
been updated anyway.
Drop the unnecessary swaps and incorrect comment and simply update the
uartclk field if the clock-rate change was successful.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename a couple of oddly named labels that are used to unlock before
returning after what they do (rather than after the context they are
used in) to improve readability.
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
added a hack to support SoCs where the UART reference clock can
change behind the back of the driver but failed to add the proper
locking.
First, make sure to take a reference to the tty struct to avoid
dereferencing a NULL pointer if the clock change races with a hangup.
Second, the termios semaphore must be held during the update to prevent
a racing termios change.
Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
Fixes: c8dff3aa8241 ("serial: 8250: Skip uninitialized TTY port baud rate update")
Cc: stable@vger.kernel.org # 5.9
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a call to the custom ->set_termios() which has implementation about
changing the state of RTS and CTS.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of the code currently used in dw8250_set_termios(), byt_set_termios()
may be reused by other methods in the future. Extract it to a common helper
function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the trivial typo in the comment: Premilinary --> Preliminary.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134529.23256-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In couple of places we may re-use temporary variable instead of
dereferencing it. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134529.23256-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.
Instead of adding ifdeffery here and there, drop ACPI_PTR().
Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 32262e2e429cdb31f9e957e997d53458762931b7.
The commit in question claims to determine the inverse of
serial8250_get_divisor() but failed to notice that some drivers override
the default implementation using a get_divisor() callback.
This means that the computed line-speed values can be completely wrong
and results in regular TCSETS requests failing (the incorrect values
would also be passed to any overridden set_divisor() callback).
Similarly, it also failed to honour the old (deprecated) ASYNC_SPD_FLAGS
and would break applications relying on those when re-encoding the
actual line speed.
There are also at least two quirks, UART_BUG_QUOT and an OMAP1510
workaround, which were happily ignored and that are now broken.
Finally, even if the offending commit were to be implemented correctly,
this is a new feature and not something which should be backported to
stable.
Cc: Pali Rohár <pali@kernel.org>
Fixes: 32262e2e429c ("serial: 8250: Fix reporting real baudrate value in c_ospeed field")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211007133146.28949-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SERIAL_8250_FSL option is used to enable a workaround for a
break-detection erratum for Freescale 16550 UARTs in the 8250 driver and
is currently also used to enable support for ACPI enumeration.
It is enabled on PPC, ARM and ARM64 whenever 8250 console support is
enabled (since the quirk is needed for sysrq handling).
Commit b1442c55ce89 ("serial: 8250: extend compile-test coverage")
enabled compile testing of the code in question but did not provide a
means to disable the option when COMPILE_TEST is enabled.
Add a conditional input prompt instead so that SERIAL_8250_FSL is no
longer enabled by default when compile testing while continuing to
always enable the quirk for platforms that may need it.
Fixes: b1442c55ce89 ("serial: 8250: extend compile-test coverage")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210924141232.4419-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In most cases it is not possible to set exact baudrate value to hardware.
So fix reporting real baudrate value which was set to hardware via c_ospeed
termios field. It can be retrieved by ioctl(TCGETS2) from userspace.
Real baudrate value is calculated from chosen hardware divisor and base
clock. It is implemented in a new function serial8250_compute_baud_rate()
which is inverse of serial8250_get_divisor() function.
With this change is fixed also UART timeout value (it is updated via
uart_update_timeout() function), which is calculated from the now fixed
baudrate value too.
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927093704.19768-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Emma Mobile integrated serial port hardware is only present on Emma
Mobile SoCs. Hence add a dependency on ARCH_RENESAS, to prevent asking
the user about this driver when configuring a kernel without Renesas
ARM32 SoC support.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7b5a4bbf2f47b2c4c127817e8b1524a650795d97.1631710085.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BRI0A49 and BDP3336 are already on the list.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170859.138813-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fsl8250_data structure is only used by ACPI support.
Hence move its definition to the driver's ACPI section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e406730a5eab880448d6bb55fbce492d281034ef.1631710623.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt
storm on K3 SoCs") introduced fixup including a register read to
RX_LVL, however, we should be using word offset than byte offset
since our registers are on 4 byte boundary (port.regshift = 2) for
8250_omap.
Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable <stable@vger.kernel.org>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210903050550.29050-1-nm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + size * count" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210905155728.11147-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-2-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2afa ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PSE UARTs on Intel Elkhart Lake support DMA mode.
Enable DMA on these ports.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210721162452.48764-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66ef ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898dc2 ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Add back an irqrestore-version of the sysrq port-unlock helper and use
it in the 8250 callbacks that need it.
Fixes: 75f4e830fa9c ("serial: do not restore interrupt state in sysrq helper")
Cc: stable@vger.kernel.org # 5.13
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210714080427.28164-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the sake of reducing layering violation add ->unregister_gpio()
callback and use it in the ->exit() one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713095821.7834-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow more drivers to be compile tested more easily, for example, when
doing subsystem-wide changes.
Verified on X86_64 as well as arm, powerpc and m68k with minimal configs
in order to catch missing implicit build dependencies.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210715083011.18887-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pointer membase is currently being in initialized with zero rather
than NULL. Fix this.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210719095533.14017-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI-based Loongson boards need configurable rather than fixed clock
frequency for serial ports.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20210715061637.134436-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't populate the const array k3_soc_devices on the stack but instead it
static. Makes the object code smaller by 44 bytes:
Before:
text data bss dec hex filename
31628 5609 128 37365 91f5 drivers/tty/serial/8250/8250_omap.o
After:
text data bss dec hex filename
31520 5673 128 37321 91c9 drivers/tty/serial/8250/8250_omap.o
Reduction of 44 bytes
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210715140759.27244-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498f3 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for Option International GSM-Ready 56K/ISDN PCMCIA modem
card.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-2-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Colin Ian King
Ji-Ze Hong (Peter Hong)
Greg Kroah-Hartman
Al Cooper
Jay Dolan
Lukas Wunner
Emil Renner Berthing
Jing Yao
Andy Shevchenko
Johan Hovold
Aman Kumar
Pali Rohár
Geert Uytterhoeven
Krzysztof Kozlowski
Nishanth Menon
Len Baker
Tang Bin
Tony Lindgren
Mario Kleiner
Zhiyong Tao
Maciej W. Rozycki
Colin Ian King
Jianmin Lv
Vignesh Raghavendra
Ondrej Zary