| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 88838d3112702 ("serial: omap_8250: Fix RTS handling") fixed
RTS pin control when in autoRTS mode.
New support added in "serial: core: Rework hw-assisted flow control support"
enables a much simpler approach; rather than masking out autoRTS
whenever writing the EFR register, use the UPSTAT_* mode to determine if
autoRTS should be enabled when raising RTS (in omap8250_set_mctrl()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cbe4f ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7af0f ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01119 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PXA variant of the 8250 UART adds a UART enable bit which must not
be cleared. Make the earlycon support maintain this bit if it is set.
This implies some initialization of the UART, but we cannot
unconditionally set the bit as some other variants require this bit to
be clear for other functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.
Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.
This workaround is disabled for omap_8250 (which uses different divisor
programming).
Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.
Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().
Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.
NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.
Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we would like to send amount of data less than FIFO size we better would do
this via PIO mode. Otherwise the overhead could be significant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.
When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want those tty fixes in that release in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In early 8250, IER is already zero so no point in writing this - twice
per line
This helped improve the SystemC model based ARC OSCI platform
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable APM X-Gene SoC serial port functionality when using ACPI table to
initialize serial port.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to terminate transfer in the __dma_rx_complete() since it's
called at the end of transfer. Special case when serial timeout occurs is
handled separately where we have to terminate transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS
mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS,
which is equivalent).
Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was
raised even before UART mode was selected.
Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled
RTS after omap_8250_shutdown().
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch invokes add_preferred_console() with ttyS based on ttyO
arguments if the user didn't specify it on its own. This ensures that
the user will see the kernel booting on his serial console in case he
forgot to update the command line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WCH384 4S board is a PCI-E card with 4 DB9 COM ports detected as
Serial controller: Device 1c00:3470 (rev 10) (prog-if 05 [16850])
Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru>
Acked-by: Zany Yan <sirlight@cox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250_omap serial driver is a new user of CONFIG_PM_RUNTIME.
However, after commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in 8250_omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
|
|
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:
SysRq :
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
Call Trace:
<IRQ> [<ffffffff812c8d27>] dump_stack+0x19/0x1b
[<ffffffff8106812e>] spin_dump+0x7e/0xd0
[<ffffffff810681a6>] spin_bug+0x26/0x30
[<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
[<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
[<ffffffff812336d8>] serial8250_console_write+0x68/0x190
[<ffffffff811eb0b0>] ? sprintf+0x40/0x50
[<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
[<ffffffff8106b276>] console_unlock+0x3e6/0x490
[<ffffffff8106b595>] vprintk_emit+0x275/0x530
[<ffffffff812c869a>] printk+0x4d/0x4f
[<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
[<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
[<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
[<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
[<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
[<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
[<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
[<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
[<ffffffff8106da01>] handle_irq_event+0x41/0x70
[<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
[<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
[<ffffffff810041c2>] handle_irq+0x22/0x40
[<ffffffff812d096e>] do_IRQ+0x4e/0xf0
[<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
<EOI> [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
[<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
[<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
[<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
[<ffffffff812c726e>] rest_init+0xbe/0xd0
[<ffffffff816a4dcb>] start_kernel+0x339/0x346
[<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...
Before ebade5e833eda30 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1. Restore that
behavior.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The original driver fixed the io address with 0xe000+idx*8,
but real io address assigned from BIOS is dynamically from
read PCI configure space 0x24, 0x20, 0x1c.
The Fintek F81504/F81508/F81512 maybe malfunction without
this patch and malfunction surely when more then 1 PCI card.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
I (wrongly) assumed that line is an int and compiler didn't complain nor
did sparse. Since of_alias_get_id() and pdev->id can get negative I
check for the error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In serial8250_rx_chars(), max_count is set to 256. Due to the
post-decrement operator used in the while() condition, the maximum
number of iterations actually 257. This is not a problem, but it is
mildly surprising if you're debugging. Use pre-decrement instead.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the serial8250_tx_dma() the tx_err flag is set in case of error. Thus, there
is no need to repeat this in __dma_tx_complete().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we have the same check inside the function we may drop it away in
__dma_tx_complete().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no more users for this functions. All the 8250 drivers are
using the rs485 handler on serial_core instead.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to remove the handler for rs485 ioctls on serial_8250, all the
drivers must use the implementation on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize recently added rs485 fields on serial_core
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fixed a sparse warning in 8250_core.c :
incorrect type in assignment (different address spaces)
the warning was because an unsigned char pointer was being assigned to
a pointer of unsigned char __iomem type .
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WCH382 is a PCI-E card with 1 LPT and 2 DB9 COM ports detected as
Serial controller: Device 1c00:3250 (rev 10) (prog-if 05 [16850])
Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.
Affected drivers:
8250
amba-pl010
atmel
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Three UART drivers (8250, atmel & amba-pl010) directly call their
enable_ms() method; the uart port lock must be acquired before
any h/w programming.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.
Convert in-tree UART drivers to new interface.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Get index of serial line from device tree using function of_alias_get_id().
If no alias is found, the 8250 core takes care of incrementing the line number.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check the return value of ioremap_nocache to make sure we got a
valid mapping.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Several init/setup functions passed the PCI BAR resource start address
to ioremap_nocache() via an unsigned long. This caused address truncation
for a 32-bit device mapped above 4 GiB (i.e. the CPU interacts with the
device via a translated address), which resulted in a kernel panic.
This patch replaces all of the instances of intermediate variable use
with pci_ioremap_bar() to ensure the full resource_size_t start address
is used and that ioremap_nocache() is still called.
The kernel panic (Exar XR17V358 PCIe device on a Freescale P2020 SBC):
Machine check in kernel mode.
Caused by (from MCSR=10008): Bus - Read Data Bus Error
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2 X-ES P2020
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14.15-xes_r2-00002-g560e401 #978
task: bf850000 ti: bffee000 task.ti: bf84c000
NIP: 80318e10 LR: 80319ecc CTR: 80318dfc
REGS: bffeff10 TRAP: 0204 Not tainted (3.14.15-xes_r2-00002-g560e401)
MSR: 00021000 <CE,ME> CR: 20adbe42 XER: 00000000
DEAR: c1058001 ESR: 00000000
GPR00: 00000000 bf84db30 bf850000 80cb4af8 00000001 00000000 80000007 80000000
GPR08: bf837c9c c1058001 00000001 00000000 80000007 00000000 80002a10 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 80cb0000 80c72dc4
GPR24: 80cb4900 fffffffe 00029000 00000001 bf8c11e8 ffffffea 80c72ce4 80cb4af8
NIP [80318e10] mem_serial_in+0x14/0x28
LR [80319ecc] serial8250_config_port+0x160/0xe38
Call Trace:
[bf84db30] [80319d94] serial8250_config_port+0x28/0xe38 (unreliable)
[bf84db60] [80315e3c] uart_add_one_port+0x148/0x3a4
[bf84dbf0] [8031bf40] serial8250_register_8250_port+0x2dc/0x3c8
[bf84dc20] [8032111c] pciserial_init_ports+0xd4/0x1c0
[bf84dd50] [803212f8] pciserial_init_one+0xf0/0x224
[bf84dd90] [802d8ff4] local_pci_probe+0x34/0x8c
[bf84dda0] [802d92c8] pci_device_probe+0x84/0xa0
[bf84ddc0] [80329ee0] driver_probe_device+0xac/0x26c
[bf84dde0] [8032a15c] __driver_attach+0xbc/0xc0
[bf84de00] [80328388] bus_for_each_dev+0x90/0xcc
[bf84de30] [80329cd0] driver_attach+0x24/0x34
[bf84de40] [80328e28] bus_add_driver+0x104/0x1fc
[bf84de60] [8032a8c8] driver_register+0x70/0x138
[bf84de70] [802d93c0] __pci_register_driver+0x48/0x58
[bf84de80] [8077e0e4] serial_pci_driver_init+0x24/0x34
[bf84de90] [80002228] do_one_initcall+0x34/0x1b0
[bf84df00] [80764294] kernel_init_freeable+0x138/0x1e8
[bf84df30] [80002a24] kernel_init+0x14/0x108
[bf84df40] [8000ef94] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
800800c4 7d290214 39290001 7c0004ac 7ca049ae 7c0004ac 4e800020 88030035
81230008 7c840030 7d292214 7c0004ac <88690000> 0c030000 4c00012c 5463063e
---[ end trace e3c16443b5d573c6 ]---
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In mtk8250_set_termios function, calculating quot value can not be zero,
otherwise, using DIV_ROUND_CLOSEST(port->uartclk, quot * baud) will fail due to
divisor is zero.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the config symbol for Mediatek MT7620 SoC to the SERIAL_8250_RT288X
dependencies.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Ralink RT2880 SoC and its successors have an internal 8250 core. This core
needs the same quirks applied as the AMD AU1xxx uart. In addition to these
quirks, the ports memory region is only 0x100 unlike the AU1xxx which has a
size of 0x1000.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
devm_kzalloc() already warns if allocation fails; remove duplicate
message.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
setup_serial_console() is obsolete and has been superseded by
early_serial_setup() which is called at the end of the function.
The IA64 arch does not call this function; only the m68k arch setup
calls this function.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Peter Hurley
Rob Herring
Andy Shevchenko
Heikki Krogerus
Greg Kroah-Hartman
Vineet Gupta
Vijay Rai
Wolfram Sang
Feng Kan
Sebastian Andrzej Siewior
Sergej Pupykin
Rafael J. Wysocki
Linus Torvalds
Rabin Vincent
Peter Hung
David Daney
Frans Klaver
Ricardo Ribalda Delgado
Sudip Mukherjee
Julien CHAUVEAU
Aaron Sierra
Eddie Huang
John Crispin