| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We want the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently dw8250_set_termios sets the input clock to the nearest
achievable rate to baudx16. If necessary, the input clock is then
divided down to baudx16 using an integer divider within the UART
device, with the divisor calculated in the 8250 core driver.
However, the clock rate set by dw8250_set_termios and subsequently
divided down could be considerably different to the target baudx16
rate, resulting in incorrect operation. This patch fixes this by
iteratively searching for an input clock rate that is within +/-1.6%
of an integer multiple of the target baudx16 rate.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a port has no dma channel defined in the device tree, then
don't attempt to allocate a dma channel for the port.
Also suppress the warning message concerning the failure to allocate
a dma channel. Continue to emit the warning message if a dma
channel is defined but cannot be allocated.
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Cedar Fork PCH has similar HSU as has been used on Intel Denverton.
Add PCI ID to get it enumerated.
While here, remove DNV part form INTEL_MID_UART_DNV_FISR to show that is
used not only on Intel Denverton from now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
move to arch_initcall to get the console up really early, it is
quite helpful for spotting early boot problems.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch remove the extra compatibility string "st,stm32-usart" from
driver & device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter
As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.
After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HSCIF has facilities that allow changing the timeout after which an RX
interrupt is triggered even if the FIFO is not filled. This patch allows
changing the default (15 bits of silence) using the existing sysfs
attribute "rx_fifo_timeout".
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes the checkpatch.pl error complain:
ERROR: space required before the open brace '{'
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.
We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable "dma_is_txing" is an unsigned int, set as either "0" or "1"
in all but one location, where it is instead set to "false". For
consistency, set dma_is_txing to "0" in this location too.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The imx serial driver uses PAGE_SIZE when allocating rx_buf, but then
uses RX_BUF_SIZE (which is currently defined as PAGE_SIZE) to describe
the length of the buffer when initialising the scatter gather list.
In order to ensure that this stays consistent, use RX_BUF_SIZE in both
locations.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-könig@pengtronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable dma_is_rxing is currently set to 1 in imx_disable_rx_int().
This is problematic as:
- whilst imx_disable_rx_int() is currently always called before
start_rx_dma() this dependency isn't obvious.
- start_rx_dma() does error checking and might exit without
enabling DMA. Currently this will result in dma_is_rxing suggesting
that DMA is being used for recieving.
To avoid these issues, move the setting of dma_is_rxing to
start_rx_dma() when appropriate.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UART core function uart_update_mctrl relies on a cached value of
modem control lines. This was used but not updated by local RTS
control functions within imx.c. These are used for RS485 line
driver enable signalling. Having an out-of-date value in the cached
mctrl can result in the transmitter being enabled when it shouldn't
be.
Fix this by updating the mctrl value before applying it.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Origin: id:8195c96e674517b82a6ff7fe914c7ba0f86e702b.1505375165.git.ian.dev@arkver.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for the rs485 specific properties defined in
Documentation/devicetree/bindings/serial/rs485.txt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Forwarded: id:20170913081833.2740-7-u.kleine-koenig@pengutronix.de (v5)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The i.MX driver defaulted to full duplex rs485 which is rather
unusual and doesn't match the default implemented in other drivers.
So change the default to half duplex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
As a side effect this adds support for parsing rs485-rts-delay and
rs485-rx-during-tx. As the driver doesn't support this though, probing
fails if these are defined.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Note that there is a small difference between the removed and the now
used implementation: The former cleared flags to 0 if rs485-rts-delay
was given, the common helper clears SER_RS485_RX_DURING_TX and
SER_RS485_ENABLED only but always which makes more sense.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[ukleinek: point out semantic change in commit log]
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Several drivers have the same device tree parsing code. Create
a common helper function for it.
This patch bases on work done by Sascha Hauer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit a6d7514b14a6 ("tty: serial: lpuart: add a more accurate baud
rate calculation method") the baud rate is now calculated inside the
lpuart32_serial_setbrg() function, so we no longer need to read the
UARTBAUD register inside lpuart32_set_termios().
The 'bd' variable can be simply removed.
This fixes the following build warning with W=1:
drivers/tty/serial/fsl_lpuart.c: In function 'lpuart32_set_termios':
drivers/tty/serial/fsl_lpuart.c:1652:32: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Fixes: a6d7514b14a6 ("tty: serial: lpuart: add a more accurate baud rate calculation method")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make this const as it is only stored in the const field 'ops' of an
uart_port structure. It is not referenced in any other file and therefore
make it static too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This dirver try to implement the Magic SysRq support[1] for
Amlogic Inc's meson platfo
>From the hardware perspective, the UART IP can't detect the 'BREAK' command
clearly via the status register. Instead, we rely on the combination of
'FRAME_ERR bit && ch == 0', and it works fine.
[1] Documentation/admin-guide/sysrq.rst
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
sccnxp_probe() returns result of regulator_disable() that may lead
to returning zero, while device is not properly initialized.
Also the driver enables clocks, but it does not disable it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current driver register irq in .startup() and free the irq in
.shutdown(), then user will see the NULL interrupt output from
'cat /proc/interrupts' after the uart port test completed:
...
41: 515 0 0 0 GICv3 257 Level fsl-lpuart
42: 2 0 0 0 GICv3 258 Level
...
It is better to register all the irqs during probe function via devm_request_irq()
to avoid to call free_irq().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Issue where unprintable characters can occur or output is cut off over
the serial uart / linux console depending on timing.
Problem occurs when changing the serial baud rate when setting up the
new console.The bcm63xx driver does a disable and flush of the uart tx
fifo while there is data still in the tx fifo.
If the tx fifo still has data it is trying to send out, we need to wait
until it is empty before disabling and flushing the uart.
When we now go to change the uart parameters including speed we check
if there is data currently in the tx fifo.If there is was mdelay(10)
and check again.If it tries 3 times and still has data in it we just
continue and sacrifice the tx fifo buffer.
A cleaner and more preferred approach would be to remove :
- spin_lock_irqsave()
- bcm_uart_disable()
- bcm_uart_flush()
However it is not clear if the author put those in to fix another
underlying issue.As a result this solution is a safer approach.
Output before the fix:
[0.306000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a° 0.315000] console[ttyS0] enabled
Output verified after the fix:
[0.315000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a bcm63xx_uart [0.334000] console[ttyS0] enabled
Signed-off-by: Russell Enderby <rte@gdn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes,
and a new serial driver. Also in here are some much needed goldfish
tty driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
tty: goldfish: Implement support for kernel 'earlycon' parameter
tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
tty: goldfish: Refactor constants to better reflect their nature
serial: 8250_port: Remove useless NULL checks
earlycon: initialise baud field of earlycon device structure
tty: hvcs: make ktermios const
pty: show associative slave of ptmx in fdinfo
tty: n_gsm: Add compat_ioctl
tty: hvcs: constify vio_device_id
tty: hvc_vio: constify vio_device_id
tty: mips_ejtag_fdc: constify mips_cdmm_device_id
Introduce 8250_men_mcb
mcb: introduce mcb_get_resource()
serial: imx: Avoid post-PIO cleanup if TX DMA is started
tty: serial: imx: disable irq after suspend
serial: 8250_uniphier: add suspend/resume support
serial: 8250_uniphier: use CHAR register for canary to detect power-off
serial: 8250_uniphier: fix serial port index in private data
serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
...
|
|
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.
Remove them to avoid confusion to static analyzers.
Fixes 6e0a5de2136b ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For now baud field of earlycon structure device is't initialised at all
in of_setup_earlycon (in oppositе to register_earlycon).
So when I use stdout-path to point earlycon device
(like stdout-path = &serial or stdout-path = "serial:115200n8")
baud field of earlycon device structure remains uninitialised and
earlycon initialization is not performed correctly as
of_setup_earlycon is used.
When pass all arguments via bootargs
(like bootargs = "earlycon=uart8250,mmio32,0xf0005000,115200n8")
initialization is performed correctly as register_earlycon is used.
So initialise baud field of earlycon device structure by value of
"current-speed" property from device tree or from options
(if they exist) when we use of_setup_earlycon
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces the 8250_men_mcb driver for the MEN 16Z125
IP-Core. This is a 16550-type UART with a 60 byte FIFO.
Due to strange old hardware, every board using this IP core requires
different values for uartclk. A reasonable default is included in
addition to the support of three boards. Additional values for other
boards will be added later.
This v2 has some whitespace fixes, I screwed this up yesterday.
Signed-off-by: Michael Moese <michael.moese@men.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The imx_transmit_buffer function should return if TX DMA has already
been started and not just skip over the buffer PIO write loop. (Which
did fix the initial problem, but could have unintentional side-effects)
Tested on an i.MX6Q board with half-duplex RS-485 and with RS-232.
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Uwe-Kleine König <u.kleine-koenig@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 514ab34dbad6 ("serial: imx: Prevent TX buffer PIO write when a DMA has been started")
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If any key on console is pressed when board is suspended,
board hangs.
Driver's interrupt handler must be guaranteed not to run while
resume/suspend_noirq() are being executed. See include/linux/pm.h
for details.
Tested on i.MX6 based board.
The idea of this fix is based on commit in official i.MX kernel tree:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
commit 81e8e7d91d81 ("tty: serial: imx: disable irq after suspend")
Disable rx irq after suspend to avoid interrupt coming in early resume.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add suspend/resume support for UniPhier serial driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250 core uses the SCR as a canary to discover if the console has
been powered-off.
This hardware does not have SCR at offset 7, but an unused register
CHAR at a different offset. As long as the character interrupt is
disabled, the register access has no impact, so it is useful as an
alternative scratch register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial8250_register_8250_port() may allocate a different port index
than requested. The driver needs to remember the returned value of
serial8250_register_8250_port() for later use. Otherwise, the .remove
hook may unregister a different port.
Fixes: 1a8d2903cb6a ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module called CONNSYS inside the SoC which could be mostly
found on those MediaTek SoCs with Bluetooth feature such as MT7622 and
MT7623 SoCs.
And the controller is made as being compatible with the 8250 register
layout with extra registers such as DMA enablement so it tends to be
integrated with reusing 8250 OF driver. However, DMA mode is not being
supported yet in the current driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When moving earlycon early_param handling to serial, the devicetree
earlycons enable condition changed slightly.
We used to only do that for 'console'/'earlycon', but now would also
for 'console='/'earlycon='.
Fix it by using the same condition like before.
Fixes: d503187b6cc4 (of/serial: move earlycon early_param handling to serial)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Ed Blake
Andy Lowe
Andy Shevchenko
Shubhrajyoti Datta
Vikas Manocha
Romain Izard
Ulrich Hecht
Gimcuan Hui
Ji-Ze Hong (Peter Hong)
Allen Pais
Martyn Welch
Romain Perier
Ian Jamison
Sascha Hauer
Uwe Kleine-König
Fabio Estevam
Bhumika Goyal
Yixun Lan
Alexey Khoroshilov
Fugang Duan
Russell Enderby
Christoph Hellwig
Linus Torvalds
Eugeniy Paltsev
Michael Moese
Maxim Yu. Osipov
Masahiro Yamada
Sean Wang
Jeffy Chen
Julia Lawall