| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.
The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:
-- CPU a -- -- CPU b --
(take port lock)
pl011_start_tx
pl011_start_tx_pio
enable TXIM in REG_IMSC -> causes uart tx intr (pl011_int)
pl011_tx_chars pl011_int
...tx chars, all done... (wait for port lock)
pl011_stop_tx .
disable TXIM .
(release port lock) -> (take port lock)
check for TXIM, not enabled
(release port lock)
return IRQ_NONE
Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.
Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <Vijaya.Kumar@cavium.com>
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When Power management is disabled then the clocks are not getting
enabled. This patch enables it for the !PM case also.
While at it also pm_runtime_set_active is called before
calling pm_runtime_enable.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk(KERN_INFO ) by pr_info(). It seems last printk()
call in serial_core.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the serial fixes in here as well to handle merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The work-around for the Qualcomm Datacenter Technologies QDF2400
erratum 44 sets the "qdf2400_e44_present" global variable if the
work-around is needed. However, this check does not happen until after
earlycon is initialized, which means the work-around is not
used, and the console hangs as soon as it displays one character.
Fixes: d8a4995bcea1 ("tty: pl011: Work around QDF2400 E44 stuck BUSY bit")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit d0aeaa83f0b0f7a92615bbdd6b1f96812f7dcfd2 ("serial: exar:
split out the exar code from 8250_pci") the exar driver got its own
Kconfig. However the text for the new option was never changed from
the original 8250_PCI text, and hence it appears confusing when you
get asked the same question twice:
8250/16550 PCI device support (SERIAL_8250_PCI) [Y/n/m/?] (NEW)
8250/16550 PCI device support (SERIAL_8250_EXAR) [Y/n/m] (NEW)
Adding to the confusion, is that there is no help text for this new
option to indicate it is specific to a certain family of cards.
Fix both issues at the same time, as well as the space vs. tab issues
introduced in the same commit.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci")
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A side effect of 89d8232411a8 ("tty/serial: atmel_serial: BUG: stop DMA
from transmitting in stop_tx") is that the console can be called with
TX path disabled. Then the system would hang trying to push charecters
out in atmel_console_putchar().
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 89d8232411a8 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting
in stop_tx")
Cc: stable <stable@vger.kernel.org> #4.4+
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If uart_flush_buffer() is called between atmel_tx_dma() and
atmel_complete_tx_dma(), the circular buffer has been cleared, but not
atmel_port->tx_len.
That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE -
atmel_port->tx_len) bytes).
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The reference manual for the i.MX28 recommends to calculate the divisor
as
divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer
, so let's do this. For a typical setup of UARTCLK = 24 MHz and baud
rate = 115200 this changes the divisor from 6666 to 6667 and so the
actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to
115194.240 Bd (error ≅ 0.005 %).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The console write code is not entirely race free (e.g. the operations
to disabling the UART interrupts are not atomic) hence locking is
required. This has been become apparent with the PREEMPT RT patchset
applied: With the fully preemptible kernel configuration the system
often ended up in a freeze already at startup.
Disable interrupts and lock using read_lock_irqsave. Try to lock in
the sysrq/oops case, but don't bother if locking fails.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Nios2 currently uses its own early printk implementation, rather than
using unified earlycon support to show boot messages on altera_uart.
Add earlycon support to altera_uart so that other archs may use it.
Also, this (together with the corresponding patch for altera_jtaguart)
will allow the early printk implementation in arch/nios2 to be removed
in a future patch.
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using dev_name() as IRQ name during request_irq() might be misleading in
case of serial over PCI. Therefore identify serial port IRQ using
uart_port's name field. This will help mapping IRQs to appropriate
ttySN(where N is the serial port index) instances.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce a field to store name of uart_port that can be used to easily
identify UART port instances on a system that has more than one UART
instance. The name is of the form ttyXN(eg. ttyS0, ttyAMA0,..) where N
is number that particular UART instance.
This field will be useful when printing debug info for a particular port
or in register IRQs with unique IRQ name. Port name is populated during
uart_add_one_port().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MSI needs it as well.
Should have no practical impact, though, as DMA is always available on
the Quark. But given the few users of pci_alloc_irq_vectors so far, this
incorrect pattern may spread otherwise.
Fixes: 3f3a46951e02 ("serial: 8250_lpss: set PCI master only for private DMA")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a UART has dedicated RTS/CTS pins, and hardware control flow is
disabled (or AUTORTS is not yet effective), changing any serial port
configuration deasserts RTS, as .set_termios() calls sci_init_pins().
To fix this, consider the current (AUTO)RTS state when (re)initializing
the pins. Note that for SCIFA/SCIFB, AUTORTS needs explicit
configuration of the RTS# pin function, while (H)SCIF handles this
automatically.
Fixes: d2b9775d795ec05f ("serial: sh-sci: Correct pin initialization on (H)SCIF")
Fixes: e9d7a45a03991349 ("serial: sh-sci: Add pin initialization for SCIFA/SCIFB")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When changing hardware control flow for a UART with dedicated RTS/CTS
pins, the new AUTORTS state is not immediately reflected in the
hardware, but only when RTS is raised. However, the serial core does
not call .set_mctrl() after .set_termios(), hence AUTORTS may only
become effective when the port is closed, and reopened later.
Note that this problem does not happen when manually using stty to
change CRTSCTS, as AUTORTS will work fine on next open.
To fix this, call .set_mctrl() from .set_termios() when dedicated
RTS/CTS pins are present, to refresh the AUTORTS or RTS state.
This is similar to what other drivers supporting AUTORTS do (e.g.
omap-serial).
Reported-by: Baumann, Christoph (C.) <cbaumann@visteon.com>
Fixes: 33f50ffc253854cf ("serial: sh-sci: Fix support for hardware-assisted RTS/CTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the .set_termios() callback resets the UART, it first waits (busy
loops) until all characters in the transmit FIFO have been transmitted,
to prevent a port configuration change from impacting these characters.
However, if the UART has dedicated RTS/CTS hardware flow control
enabled, these characters may have been stuck in the FIFO due to CTS not
being asserted by the remote side.
- When a new user opens the port, .set_termios() is called while
transmission is still disabled, leading to an infinite loop:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s!
- When an active user changes port configuration without waiting for
the draining of the transmit FIFO, this may also block indefinitely,
until CTS is asserted by the remote side.
This has been observed with SCIFA (on r8a7740/armadillo), and SCIFB and
HSCIF (on r8a7791/koelsch).
To fix this, remove the code that waits for the draining of the transmit
FIFO.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
9600 is old school.
Most applications use 115200 as the default baud these days.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lock is a sleeping lock and local_irq_save() is not the
standard implementation now. Working for both -RT and non
RT.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the tty/serial fixes in here to handle bugfixes and merge
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.11-rc4.
One of these fix a long-standing issue in the ldisc code that was
found by Dmitry Vyukov with his great fuzzing work. The other fixes
resolve other reported issues, and there is one revert of a patch in
4.11-rc1 that wasn't correct.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: fix data race in tty_ldisc_ref_wait()
tty: don't panic on OOM in tty_set_ldisc()
Revert "tty: serial: pl011: add ttyAMA for matching pl011 console"
tty: acpi/spcr: QDF2400 E44 checks for wrong OEM revision
serial: 8250_dw: Fix breakage when HAVE_CLK=n
serial: 8250_dw: Honor clk_round_rate errors in dw8250_set_termios
|
|
Pull GPIO fixes from Linus Walleij:
"Here is the first set of GPIO fixes for 4.11. It was delayed a bit
beacuse I was chicken when linux-next was not rotating last week.
This hits the ST serial driver in drivers/tty/serial and that has an
ACK from Greg, he suggested to keep the old GPIO fwnode API around to
smoothen things in the merge Windod and those have now served their
purpose so we take them out and convert the last driver to the new
API.
Apart from that it's fixes as usual.
Summary:
- set the parent on the Altera A10SR driver, also fix high level
IRQs.
- fix error path on the mockup driver.
- compilation noise about unused functions fixed.
- fix missed interrupts on the MCP23S08 expander, this is also tagged
for stable.
- retire the interrim helpers devm_get_gpiod_from_child() used to
smoothen merging in the merge window"
* tag 'gpio-v4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio:mcp23s08 Fixed missing interrupts
serial: st-asc: Use new GPIOD API to obtain RTS pin
gpio: altera: Use handle_level_irq when configured as a level_high
gpio: xgene: mark PM functions as __maybe_unused
gpio: mockup: return -EFAULT if copy_from_user() fails
gpio: altera-a10sr: Set gpio_chip parent property
|
|
As of commit bb475230b8e5 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Coverity complains about uart_state checks in polling functions. And it
is indeed correct. We do something like this:
struct uart_state *state = drv->state + line;
if (!state)
return;
Adding 'line' to drv->state would move the potential NULL pointer to
something near NULL and the check is useless. Even if we checked pure
drv->state, nothing guarantees it is not freed and NULLed after the
check. So if the only user of this interface (kgdboc) needs to assure
something, this is neither the correct thing, nor place to do so.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81866 supports baud rates higher than 115200 but needs to raise
it's clock speed from 1.84 to 14.76 MHz.
This is eight times faster, so gives 921600 as resulting baud_base.
F81866 clock register 0xf2:
Bit 7-2 reserved
Bit 1-0 00: 1.8432MHz
01: 18.432MHz
10: 24MHz
11: 14.769MHz
Signed-off-by: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The number of uartlites should be set by a kernel parameter instead of
using a #define. This allows the user to set the number of uartlites
using only kconfig and not modifying kernel source.
The uartlite is used by FPGAs that support a basically unlimited number
of uarts so limiting it at 16 dosn't make sense as users might need more
than that.
Signed-off-by: Sam Povilus <kernel.development@povil.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The core handles the clocking now. Remove the clock disable in
suspend. In resume we enable the clocks and disable after register
write.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Nios2 currently uses its own early printk implementation, rather than
using unified earlycon support to show boot messages on altera_jtaguart
(and altera_uart for that matter).
Add earlycon support to altera_jtaguart so that other archs may use it. Also,
this will allow the early printk implementation in arch/nios2 to eventually be
removed in a future patch.
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The original patch makes the condition always true, so it is wrong.
It masks (but not fixes) the bug described in the commit message
but introduces a regression (no console is selected by SPCR)
in regular (no 'console=ttyAMA') case.
s/||/&&/ would not fix the problem as the root cause was identified
incorrectly.
This reverts commit aea9a80ba98a0c9b4de88850260e9fbdcc98360b.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commits mentioned below adapt the GPIO API to allow more information
to be passed directly through devm_get_gpiod_from_child() in the first
instance. This facilitates the removal of subsequent calls, such as
gpiod_direction_output(). This patch firstly moves to utilise the new
API and secondly removes the now superfluous call do set the direction.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Also drop the header file dummies that only this driver was using]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Adds pm runtime support to xilinx uart ps.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Passing "serial" as name during request_irq() results in all serial port
irqs have same name. This does not help much to easily identify which
irq belongs to which serial port instance. Therefore pass dev_name()
during request_irq() so that better identifiable name is listed for
serial ports in cat /proc/interrupts output.
Output of cat /proc/interrupts
Before this patch:
26: 689 0 GICv2 309 Edge serial
After this patch:
26: 696 0 GICv2 309 Edge 2530c00.serial
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
atmel_serial.h is only used by atmel_serial.c, so there's no need for
it to lie in include/linux.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix typo in "Dricer".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct cache is only used in suspend/resume. Exclude it when PM is not
selected.
Suggested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The samx7 family uses the same UART/USART IP as the at91/sama5 families but
has 8 of those.
Suggested-by: Szemző András <sza@esh.hu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that kernel panic happens when DMA is enabled
and we press enter key while the kernel booting on the serial console.
* An interrupt may occur after sci_request_irq().
* DMA transfer area is initialized by setup_timer() in sci_request_dma()
and used in interrupt.
If an interrupt occurred between sci_request_irq() and setup_timer() in
sci_request_dma(), DMA transfer area has not been initialized yet.
So, this patch changes the order of sci_request_irq() and
sci_request_dma().
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com>
[Shimoda changes the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The original patch makes the condition always true, so it is wrong.
It masks (but not fixes) the bug described in the commit message
but introduces a regression (no console is selected by SPCR)
in regular (no 'console=ttyAMA') case.
s/||/&&/ would not fix the problem as the root cause was identified
incorrectly.
This reverts commit aea9a80ba98a0c9b4de88850260e9fbdcc98360b.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 6a171b299379 ("serial: 8250_dw: Allow hardware flow control to be
used") recently broke the 8250_dw driver on platforms which don't select
HAVE_CLK, as dw8250_set_termios() gets confused by the behaviour of the
fallback HAVE_CLK=n clock API in linux/clk.h which pretends everything
is fine but returns (valid) NULL clocks and 0 HZ clock rates.
That 0 rate is written into the uartclk resulting in a crash at boot,
e.g. on Cavium Octeon III based UTM-8 we get something like this:
1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 41, base_baud = 25000000) is a OCTEON
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at drivers/tty/serial/serial_core.c:441 uart_get_baud_rate+0xfc/0x1f0
...
Call Trace:
...
[<ffffffff8149c2e4>] uart_get_baud_rate+0xfc/0x1f0
[<ffffffff814a5098>] serial8250_do_set_termios+0xb0/0x440
[<ffffffff8149c710>] uart_set_options+0xe8/0x190
[<ffffffff814a6cdc>] serial8250_console_setup+0x84/0x158
[<ffffffff814a11ec>] univ8250_console_setup+0x54/0x70
[<ffffffff811901a0>] register_console+0x1c8/0x418
[<ffffffff8149f004>] uart_add_one_port+0x434/0x4b0
[<ffffffff814a1af8>] serial8250_register_8250_port+0x2d8/0x440
[<ffffffff814aa620>] dw8250_probe+0x388/0x5e8
...
The clock API is defined such that NULL is a valid clock handle so it
wouldn't be right to check explicitly for NULL. Instead treat a
clk_round_rate() return value of 0 as an error which prevents uartclk
being overwritten.
Fixes: 6a171b299379 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-serial@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: bcm-kernel-feedback-list@broadcom.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clk_round_rate returns a signed long and may possibly return errors
in it, for example if there is no possible rate.
Till now dw8250_set_termios ignored any error, the signednes and would
just use the value as input to clk_set_rate. This of course falls apart
if there is an actual error, so check for errors and only try to set
a rate if the value is actually valid.
This turned up on some Rockchip platforms after commit
6a171b299379 ("serial: 8250_dw: Allow hardware flow control to be used")
enabled set_termios callback in all cases, not only ACPI.
Fixes: 6a171b299379 ("serial: 8250_dw: Allow hardware flow control to be used")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If DMA is not available (even when configured in DeviceTree), the driver
will fail the startup procedure thus making serial console not
available.
For example this causes boot failure on QEMU ARMv7 (Exynos4210, SMDKC210):
[ 1.302575] OF: amba_device_add() failed (-19) for /amba/pdma@12680000
...
[ 11.435732] samsung-uart 13800000.serial: DMA request failed
[ 72.963893] samsung-uart 13800000.serial: DMA request failed
[ 73.143361] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
DMA is not necessary for serial to work, so continue with UART startup
after emitting a warning.
Fixes: 62c37eedb74c ("serial: samsung: add dma reqest/release functions")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.
Create empty placeholder header that maps to <linux/types.h>.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix typos and add the following to the scripts/spelling.txt:
comsume||consume
comsumer||consumer
comsuming||consuming
I see some variable names with this pattern, but this commit is only
touching comment blocks to avoid unexpected impact.
Link: http://lkml.kernel.org/r/1481573103-11329-19-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now we can also jump to boot prom from sunhv console by sending
break twice on console for both running and panicked kernel
cases.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On panic, all other CPUs are stopped except the one which had
hit panic. To keep console alive, we need to migrate hvcons irq
to panicked CPU.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Qualcomm Datacenter Technologies QDF2400 family of SoCs contains a
custom (non-PrimeCell) implementation of the SBSA UART. Occasionally the
BUSY bit in the Flag Register gets stuck as 1, erratum 44 for both 2432v1
and 2400v1 SoCs.Checking that the Transmit FIFO Empty (TXFE) bit is 0,
instead of checking that the BUSY bit is 1, works around the issue.
To facilitate this substitution of flags and values, introduce
vendor-specific inversion of Feature Register bits when UART AMBA Port
(UAP) data is available. For the earlycon case, prior to UAP availability,
implement alternative putc and early_write functions.
Similar to what how ARMv8 ACPI PCI quirks are detected during MCFG parsing,
check the OEM fields of the Serial Port Console Redirection (SPCR) ACPI
table to determine if the current platform is known to be affected by the
erratum.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fractional baud rate generator is available when using the
asynchronous mode of Atmel USART controllers. It makes it possible to
use higher baudrates, in exchange for a less precise clock with a
variable duty cycle.
The existing code restricts its use to the normal mode of the USART
controller, following the recommendation from the datasheet for the
first chip embedding this type of controller. This recommendation has
been removed from the documentation for the newer chips. After
verification, all revisions of this controller should be able to use the
fractional baud rate generator with the different asynchronous modes.
Removing the condition on ATMEL_US_USMODE makes it possible to get
correct baudrates at high speed in more cases.
This was tested with a board using an Atmel SAMA5D2 chip and a TI
WL1831 WiFi/Bluetooth combo chip at 3 Mbauds, with hardware flow control
enabled.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Jayachandran C
Shubhrajyoti Datta
Andy Shevchenko
Wei Qiao
Greg Kroah-Hartman
Timur Tabi
Paul Gortmaker
Nicolas Ferre
Richard Genoud
Uwe Kleine-König
Stefan Agner
Tobias Klauser
Vignesh R
Jan Kiszka
Geert Uytterhoeven
Lee Jones
Lionel Debieve
Linus Torvalds
Philipp Zabel
Jiri Slaby
Lukas Redlinger
Sam Povilus
Aleksey Makarov
Elena Reshetova
Alexandre Belloni
Takatoshi Akiyama
James Hogan
Heiko Stuebner
Krzysztof Kozlowski
Ingo Molnar
Masahiro Yamada
Vijay Kumar
Christopher Covington
Romain Izard