| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to tty_ioctl(4) (from man-pages 4.04) the rng member only
counts 0->1 transitions. For the other signals (DSR, CD, CTS) both edges
are supposed to be counted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure that events that are not handled in the irq function don't
trigger an interrupt.
When the serial port is operated in DTE mode, the events for DCD and RI
events are enabled after a system reset by default.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This gives the irq core a chance to disable the serial interrupt in case
an event isn't cleared in the handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When in DTE mode, the bit USR2_RIIN is active low. So invert the logic
accordingly.
Fixes: 90ebc4838666 ("serial: imx: repair and complete handshaking")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide changes which
allow to reuse mxs-auart.c code for ASM9260.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SC16is7xx has feature for auto hardware flow control using RTS/CTS,
so we don't need "uart_handle_cts_change" to invoke "start_tx/stop_tx"
for flow control.
In addition, for software CTS, interrupt "SC16IS7XX_IIR_CTSRTS_SRC"
just report the nCTS change of state from active(low) to inactive(high),
driver don't know when the state of nCTS change from incactive to active,
so can't resume the transmission when a peer device is again ready and
re-assert nRTS signal.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some RS-232 to RS-485 transceivers require Rx to be disabled on Tx to
avoid echo of Tx data into the Rx buffer. Specifically, the XR3160E
RS-232/RS-485/RS-422 transceiver behaves this way.
This commit disables Rx on active Tx when SER_RS485_ENABLED is active and
SER_RS485_RX_DURING_TX is disabled.
Note that this is a change in behavior of the driver. Until now
SER_RS485_RX_DURING_TX was enabled unconditionally even when disabled in
the TIOCSRS485 ioctl serial_rs485 flags field.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enabling support for the UART on Marvell EBU SoCs only make sense when
compiling for Marvell EBU SoCs, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_MVEBU_UART
drivers/tty/serial/Kconfig: bool "Marvell EBU serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since the code wasn't using module_init to begin with, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split off the bulk of the existing meson_serial_console_write()
implementation into meson_serial_port_write() for implementing
meson_serial_early_console_write().
Use "meson" as the earlycon driver name, courtesy of Nicolas.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The issue with setting up a fixed clock rate at probe is that it would
overwrite the console rate set by the bootloader for its console device.
This would result in serial out corruption or missing log when we system
is booted with earlycon. This is not a issue if we boot system without
earlycon.
This setup is at least not required with the mainline driver, this code
used to be required because the clk_enable() call would fail if
clk_set_rate() wasn't called first.
Originally the issue was noticed on DB410c which is based on APQ8016
chipset.
Without this patch the console log with earlycon would look like:
...
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
����+HH��0.699378] console [ttyMSM0] enabled
[ 0.699378] console [ttyMSM0] enabled
[ 0.702003] bootconsole [uart0] disabled
[ 0.702003] bootconsole [uart0] disabled
...
with this patch I can see all the skipped lines on the console
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For tty operations which may expect uart port to have been removed
but still have other necessary work to accomplish, check for NULL
uart port; specifically uart_close(), uart_hangup() and sub-functions
(uart_shutdown() and uart_port_shutdown()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For serial core operations not already excluded by holding port->mutex,
use reference counting to protect deferencing the state->uart_port.
Introduce helper functions, uart_port_ref() and uart_port_deref(), to
wrap uart_port access, and helper macros, uart_port_lock() and
uart_port_unlock(), to wrap combination uart_port access with uart
port lock sections.
Port removal in uart_remove_one_port() waits for reference count to
drop to zero before detaching the uart port from struct uart_state.
For functions only reading the tx circular buffer indexes (where the
uart port lock is claimed to prevent concurrent users), a NULL uart
port is simply ignored and the operation completes normally.
For functions change the tx circular buffer indexes (where the uart
port lock is claimed to prevent concurrent users), the operation is
aborted if the uart port is NULL (ie., has been detached).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_remove_one_port() may race with every serial core operation
requiring a valid dereference of state->uart_port. In particular,
uart_remove_one_port() may unlink the uart port concurrently with
any serial core operation that may dereference same.
Ensure safe dereference for those operations that already claim
the port->mutex, and extend that guarantee for trivial cases,
such as the ioctl handlers. Introduce the uart_port_check() helper
which asserts port->mutex is held (only when lockdep is on).
For ioctls, return -EIO as if the port has been hung up (since it has).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare uart_poll_init() to safely dereference uart port; expand the
port mutex section to guarantee uart port remains valid until
uart_poll_init() completes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ASYNC_SUSPENDED bit in the tty_port::flags field with
TTY_PORT_SUSPENDED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_suspended() and tty_port_suspended() to abstract
atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ASYNC_NORMAL_ACTIVE bit in the tty_port::flags field with
TTY_PORT_ACTIVE bit in the tty_port::iflags field. Introduce helpers
tty_port_set_active() and tty_port_active() to abstract atomic bit ops.
Extract state changes from port lock sections, as this usage is
broken and confused; the state transitions are protected by the
tty lock (which mutually excludes parallel open/close/hangup),
and no user tests the active state while holding the port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Abstract TTY_IO_ERROR status test treewide with tty_io_error().
NB: tty->flags uses atomic bit ops; replace non-atomic bit test
with test_bit().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Version 2 of the Server Base System Architecture (SBSAv2) describes UART
hardware registers as 32 bits wide, giving no guidance on access sizes. The
SBSA UART driver previously assumed partial-length 16 and 8 bit accesses would
work. But the SBSAv2 UART hardware on the Qualcomm Technologies QDF2432 only
supports full-length 32 bit register accesses, so use those exclusively. This
is compatible with SBSAv3, which explicitly requires UART hardware support 32
(and 16 and sometimes 8) bit accesses.
Tested on Juno, Midway, QDF2432, Seattle, and X-Gene 1.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Cc: stable <stable@vger.kernel.org> # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 21947ba654a6 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654a6 ("serial: 8250_pci: replace switch-case by formula")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 8d2acdb9fc3a544ab0442634531834d6007b5467.
It's causing problems, and somehow I missed that Peter didn't like it at
all :(
So revert it for now until it gets sorted out.
Reported-by: Mason <slash.tmp@free.fr>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
|
|
When in half-duplex mode RX will be disabled before TX, but not
enabled after deactivating transmitter. This patch enables
UART_IER_RLSI and UART_IER_RDI interrupts after TX is over.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
Acked-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2905697a82eaf20606ced164d853b52d1b94aaa8.
The commit introduced two build warnings:
drivers/tty/serial/uartlite.c: In function ‘ulite_request_port’:
drivers/tty/serial/uartlite.c:348:21: warning: assignment discards
‘const’ qualifier from pointer target type
port->private_data = &uartlite_be;
^
drivers/tty/serial/uartlite.c:354:22: warning: assignment discards
‘const’ qualifier from pointer target type
port->private_data = &uartlite_le;
^
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Maarten Brock <m.brock@vanmierlo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
CONFIG_SERIAL_8250_RSA has waited for a long
time to have meaningful help text so let's
finally describe what this option actually does.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch optimizes UART rx fifo access routine by reading UART SFR
when necessary. At first, the "fifocnt" variable will be initialized
as Rx FIFO count. So we don't need to access UFSTAT(FIFO status) register
every time to check FIFO count because we know that count with "fifocnt".
After all data were read out from Rx FIFO, the "fifocnt" will be set as 0.
Lastly, UFSTAT will be accessed again to check whether the data remains
by any chance.
Signed-off-by: Youngmin Nam <ym0914@gmail.com>
Reviewed-by: Jung-Ick Guack <ji.guack@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PL011 UART has hardware mark/space parity ability, this trivial patch adds support for it.
Tested on Raspberry Pi v1, v2 (BCM2835 and BCM2836)
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for :
- CP-102E: 2 ports RS232 PCIE card
- CP-102EL: 2 ports RS232 PCIE card
- CP-132EL: 2 ports RS422/485 PCIE card
- CP-114EL: 4 ports RS232/422/485 PCIE card
- CP-104EL-A: 4 ports RS232 PCIE card
- CP-168EL-A: 8 ports RS232 PCIE card
- CP-118EL-A: 8 ports RS232/422/485 PCIE card
- CP-118E-A: 8 ports RS422/485 PCIE card
- CP-138E-A: 8 ports RS422/485 PCIE card
- CP-134EL-A: 4 ports RS422/485 PCIE card
- CP-116E-A (A): 8 ports RS232/422/485 PCIE card
- CP-116E-A (B): 8 ports RS232/422/485 PCIE card
This patch is based on information extracted from
vendor mxupcie driver available on MOXA website.
I was able to test it on a CP-168EL-A on PC.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
up_to_u8250p() casts struct uart_port * to struct uart_8250_port *. Update code
to use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Mediatek 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `mtk8250_set_termios':
:(.text+0x1bee8): undefined reference to `serial8250_do_set_termios'
:(.text+0x1bf10): undefined reference to `uart_get_baud_rate'
:(.text+0x1c09c): undefined reference to `uart_get_divisor'
drivers/tty/built-in.o: In function `mtk8250_do_pm':
:(.text+0x1c0d0): undefined reference to `serial8250_do_pm'
drivers/tty/built-in.o: In function `mtk8250_probe':
:(.text+0x1c2e4): undefined reference to `serial8250_register_8250_port'
serial/8250/8250_mtk.c:287:242: error: data definition has no type or storage class [-Werror]
serial/8250/8250_mtk.c:287:122: error: 'mtk8250_platform_driver_init' defined but not used [-Werror=unused-function]
This changes the symbol to a 'tristate', so the dependency on
SERIAL_8250 also works when that is set to 'm'.
To actually build the driver, we also need to include <linux/module.h>.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Ingenic 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `ingenic_uart_probe':
8250_ingenic.c:(.text+0x1c1a0): undefined reference to `serial8250_register_8250_port'
This changes the symbol to a 'tristate', plus a dependency on
SERIAL_8250, which makes it work again. Unlike the other
soc-specific backends, this one has no dependency on an
architecture or a platform. I'm adding a dependency on
MIPS || COMPILE_TEST as well here, to avoid showing the driver
on architectures that are not interested in it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The newly added uniphier serial port driver fails to build as
a loadable module when the base 8250 driver is built-in and
its console support enabled:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
This changes the driver to only provide the early console support
if it is built-in itself as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit cafe1ac64023 ("drivers/tty: make serial
8250_ingenic.c explicitly non-modular"), which attempted to remove dead
code but did not have the desired effect when the main 8250 driver was
a loadable module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d72d391c126e ("drivers/tty/serial: make
8250/8250_mtk.c explicitly non-modular"), which intended to remove dead
code but did not have the desired effect when the main 8250 driver was
a module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Armada-3700's uart is a simple serial port, which doesn't
support. Configuring the modem control lines. The uart port has a 32
bytes Tx FIFO and a 64 bytes Rx FIFO
The uart driver implements the uart core operations. It also support the
system (early) console based on Armada-3700's serial port.
Known Issue:
The uart driver currently doesn't support clock programming, which means
the baud-rate stays with the default value configured by the bootloader
at boot time
[gregory.clement@free-electrons.com: Rewrite many part which are too long
to enumerate]
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the mctrl_gpio driver can be built as a module, it needs to have its
license specified with MODULE_LICENSE. Otherwise, it cannot access
required symbols exported through EXPORT_SYMBOL_GPL.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gcc warns about a potential use of an uninitialized variable in this driver:
drivers/tty/serial/ifx6x60.c: In function 'ifx_spi_complete':
drivers/tty/serial/ifx6x60.c:713:6: warning: 'more' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (more || ifx_dev->spi_more || queue_length > 0 ||
Unlike a lot of other such warnings, this one is correct and describes
an actual problem in the handling of the "IFX_SPI_HEADER_F" result code.
This appears to be a result from a restructuring of the driver that
dates back to before it was merged in the kernel, so it's impossible
to know where it went wrong. I also don't know what that result code
means, so I have no idea if setting 'more' to zero is the correct
solution, but at least it makes the behavior reproducible rather than
depending on whatever happens to be on the kernel stack.
This patch initializes the 'more' variable to zero in each of the
three code paths that could result in undefined behavior before,
which is more explicit than initializing it at the start of the
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With SAMA5D2, the UART has hw timeout but the offset of the register to
define this value is not the same as the one for USART.
When using the new UART, the value of this register was 0 so we never
get timeout irqs. It involves that when using DMA, we were stuck until
the execution of the dma callback which happens when a buffer is full
(so after receiving 2048 bytes).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit c39dfebc7798956fd2140ae6321786ff35da30c3, the modular support
code for atmel_serial was removed, as the driver cannot be built as a
module. Because no use case was proposed, the dynamic driver binding
support was removed as well.
The atmel_serial driver can manage up to 7 serial controllers, which are
multiplexed with other functions. For example, in the Atmel SAMA5D2, the
Flexcom controllers can work as USART, SPI or I2C controllers, and on
all Atmel devices serial lines can be reconfigured as GPIOs.
My use case uses GPIOs to transfer a firmware update using a custom
protocol on the lines used as a serial port during the normal life of
the device. If it is not possible to unbind the atmel_serial driver, the
GPIO lines remain reserved and prevent this case from working.
This patch reinstates the atmel_serial_remove function, and fixes it as
it failed to clear the "clk" field on removal, triggering an oops when
a device was bound again after being unbound.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Kconfig option SERIAL_8250_RT288X seems to be only relevant on MIPS
platforms, so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This device generates a short rising pulse on the interrupt request line.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Uwe Kleine-König
Oleksij Rempel
Wills Wang
Geert Uytterhoeven
Baruch Siach
Geert Uytterhoeven
Paul Gortmaker
Julia Lawall
Andreas Färber
Srinivas Kandagatla
Peter Hurley
Christopher Covington
Alexandre Belloni
David Müller
Linus Walleij
Greg Kroah-Hartman
Yegor Yefremov
Sudip Mukherjee
Andy Shevchenko
Maciej S. Szmigiero
Youngmin Nam
Ed Spiridonov
Mathieu OTHACEHE
Arnd Bergmann
Wilson Ding
Romain Izard
Ludovic Desroches
Jean Delvare
Maarten Brock