aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial
AgeCommit message (Collapse)AuthorFilesLines
2014-01-07serial: sirf: correct condition for fetching dma buffer into ttyQipan Li1-2/+6
In rx dma-callback it calls tasklet_schedule, if the tasklet be scheduled after all the dma-callback in the rx dma channel, current check condition in the tasklet will not do fetch dma buffer into tty because tx_issued is equal with tx_completed, so as timeout tasklet does. so we check whether we should fetch the whole dma buffer into tty according to the status of transactions in rx dma channel. Signed-off-by: Qipan Li <Qipan.Li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07serial: sirf: provide pm entries of uart_opsQipan Li1-3/+11
this patch provides PM entry of uart_ops, then drop clk enable and disable because serial core will do it. the patch also fixes the issue that uart hang in resume caused by not-enabled clock. Signed-off-by: Qipan Li <Qipan.Li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07serial: sirf: use PM macro initialize PM functionsQipan Li1-6/+11
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions instead of legacy suspend and resume entries of platform_driver. this will add hibernation support automatically as suspend to disk entries are also set. Signed-off-by: Qipan Li <Qipan.Li@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07serial: clps711x: Enable driver compilation with COMPILE_TESTAlexander Shiyan2-20/+23
This helps increasing build testing coverage. To do this, read{write}_relaxed() functions was be replaced with simple read{write}() variants. Potential "uninitialized variable" warnings was be fixed if driver compiled without MFD_SYSCON. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07serial: clps711x: Add support for N_IRDA line disciplineAlexander Shiyan1-8/+12
This patch replace custom handling of IrDA feature with N_IRDA line discipline, so IrDA mode can be used with irtty driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07tty: delete non-required instances of include <linux/init.h>Paul Gortmaker9-9/+0
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-01-07treewide: fix comments and printk msgsMasanari Iida1-1/+1
This patch fixed several typo in printk from various part of kernel source. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-01-02Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/driversOlof Johansson1-50/+137
From Simon Horman: Third Round of Renesas SH SCI Updates for v3.14 * Add Device Tree Support * Remove platform data mapbase and irqs fields * Remove platform data scbrr_algo_id field * tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: serial: sh-sci: Add OF support serial: sh-sci: Add device tree bindings documentation serial: sh-sci: Remove platform data mapbase and irqs fields serial: sh-sci: Remove platform data scbrr_algo_id field Signed-off-by: Olof Johansson <olof@lixom.net>
2014-01-02Merge branch 'renesas/drivers-sci2' into next/driversOlof Johansson2-168/+154
* renesas/drivers-sci2: serial: sh-sci: Rework baud rate calculation serial: sh-sci: Compute overrun_bit without using baud rate algo serial: sh-sci: Remove unused GPIO request code serial: sh-sci: Move overrun_bit and error_mask fields out of pdata serial: sh-sci: Support resources passed through platform resources serial: sh-sci: Don't check IRQ in verify port operation serial: sh-sci: Set the UPF_FIXED_PORT flag serial: sh-sci: Remove duplicate interrupt check in verify port op serial: sh-sci: Simplify baud rate calculation algorithms serial: sh-sci: Remove baud rate calculation algorithm 5 serial: sh-sci: Sort headers alphabetically serial: sh-sci: Convert to clk_prepare/unprepare serial: sh-sci: Don't enable/disable port from within break timer serial: sh-sci: Fix warnings due to improper casts and printk formats
2014-01-02Merge tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanupOlof Johansson2-151/+132
From Simon Horman: Second Round of Renesas SH SCI updates for v3.14 * Rework baud rate calculation * Compute overrun_bit without using baud rate algo * Remove unused GPIO request code * Move overrun_bit and error_mask fields out of pdata * Support resources passed through platform resources * Don't check IRQ in verify port operation * Set the UPF_FIXED_PORT flag * Remove duplicate interrupt check in verify port op * Simplify baud rate calculation algorithms * Remove baud rate calculation algorithm 5 * Sort headers alphabetically * tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: serial: sh-sci: Rework baud rate calculation serial: sh-sci: Compute overrun_bit without using baud rate algo serial: sh-sci: Remove unused GPIO request code serial: sh-sci: Move overrun_bit and error_mask fields out of pdata serial: sh-sci: Support resources passed through platform resources serial: sh-sci: Don't check IRQ in verify port operation serial: sh-sci: Set the UPF_FIXED_PORT flag serial: sh-sci: Remove duplicate interrupt check in verify port op serial: sh-sci: Simplify baud rate calculation algorithms serial: sh-sci: Remove baud rate calculation algorithm 5 serial: sh-sci: Sort headers alphabetically Signed-off-by: Olof Johansson <olof@lixom.net>
2013-12-29Merge tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanupOlof Johansson1-17/+22
From Simon Horman: Renesas SH SCI updates for v3.14 Updates for the SH SCI serial driver * Convert to clk_prepare/unprepare * Fix warnings due to improper casts and printk formats * tag 'renesas-sh-sci-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: serial: sh-sci: Convert to clk_prepare/unprepare serial: sh-sci: Don't enable/disable port from within break timer serial: sh-sci: Fix warnings due to improper casts and printk formats Signed-off-by: Olof Johansson <olof@lixom.net>
2013-12-24Merge 3.13-rc5 into tty-nextGreg Kroah-Hartman2-2/+8
We need the tty fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-24serial: sh-sci: Add OF supportBastian Hecht1-3/+98
Extend the driver to with support for SCIx device tree bindings. A minimal set of features is supported, additional properties can be added later should the need to describe more device features arise. Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Remove platform data mapbase and irqs fieldsLaurent Pinchart1-26/+34
The fields are not used anymore by board files, remove them. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Remove platform data scbrr_algo_id fieldLaurent Pinchart1-21/+5
The field isn't set by any board, remote it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Rework baud rate calculationLaurent Pinchart1-7/+30
Computing the baud rate register value requires knowledge of the hardware sampling rate. This information is currently encoded in a baud rate calculation algorithm ID passed through platform data. However, it can be derived from the port type directly in most cases. Compute the sampling rate internally in the driver if the baud rate calculation algorithm ID isn't specified, and allow platforms to override the sampling rate through platform data in special cases (this is only required for SCIFA ports on sh7723 and sh7724, the reason needs to be investigated). Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Compute overrun_bit without using baud rate algoLaurent Pinchart1-12/+14
The overrun bit index is a property of the hardware. It's currently computed based on a different and unrelated hardware property, the baud rate calculation algorithm. Compute it using hardware identification information only. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Remove unused GPIO request codeLaurent Pinchart1-67/+0
The driver requests at initialization time GPIOs passed through platform data. No platform makes use of this feature, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Move overrun_bit and error_mask fields out of pdataLaurent Pinchart2-28/+24
None of the fields is ever set by board code, and both of them are set in the driver at probe time. Move them out of struct plat_sci_port to struct sci_port. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Support resources passed through platform resourcesLaurent Pinchart1-16/+49
Memory and IRQ resources are currently passed to the driver through platform data. Support passing them through the standard platform resources mechanism instead. This deprecates platform data resources. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Don't check IRQ in verify port operationLaurent Pinchart1-4/+0
The IRQ number can't be modified by the user as the port is fixed. There's no need to check the new IRQ number as it will be ignored by the core. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Set the UPF_FIXED_PORT flagLaurent Pinchart1-1/+1
The base address, IRQ and baud rate generator parent clock rate can't be changed by userspace. Mark the port as fixed. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Remove duplicate interrupt check in verify port opLaurent Pinchart1-1/+1
The driver checks if the interrupt number is greater than nr_irqs and returns an error in that case. The same check is already performed by the caller, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Simplify baud rate calculation algorithmsLaurent Pinchart1-4/+4
Rewrite the baud rate register value calculations in easier to read forms. The computed value isn't modified. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Remove baud rate calculation algorithm 5Laurent Pinchart1-2/+0
The algorithm isn't used, remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-24serial: sh-sci: Sort headers alphabeticallyLaurent Pinchart1-21/+21
This helps locating duplicates. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-20ARM/serial: at91: switch atmel serial to use gpiolibLinus Walleij1-18/+31
This passes the errata fix using a GPIO to control the RTS pin on one of the AT91 chips to use gpiolib instead of the AT91-specific interfaces. Also remove the reliance on compile-time #defines and the cpu_* check and rely on the platform passing down the proper GPIO pin through platform data. This is a prerequisite for getting rid of the local GPIO implementation in the AT91 platform and move toward multiplatform. The patch also adds device tree support for getting the RTS GPIO pin from the device tree on DT boot paths. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2013-12-19serial: Remove old SC26XX driverAlexander Shiyan3-768/+0
New driver for NXP (Philips) UART ICs was introduced in September 2012. Old driver no longer used anywhere, this patch removes it. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-19serial: add support for 200 v3 series Titan cardYegor Yefremov1-0/+4
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-19serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chipJonathan Woithe1-2/+2
Fix the initialisation of older Quatech serial cards which are fitted with the AMCC PCI Matchmaker interface chip. Signed-off-by: Jonathan Woithe (jwoithe@just42.net) Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17tty: xuartps: Properly guard sysrq specific codeSoren Brinkmann1-0/+2
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support' (0c0c47bc40a2e358d593b2d7fb93b50027fbfc0c) introduced sysrq support without properly guarding sysrq specific code which results in build errors when sysrq is disabled: DNAME=KBUILD_STR(xilinx_uartps)" -c -o drivers/tty/serial/.tmp_xilinx_uartps.o drivers/tty/serial/xilinx_uartps.c drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr': drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1 Reported-by: Masanari Iida <standby24x7@gmail.com> Cc: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: 8250_dw: add new ACPI IDsMika Westerberg1-0/+2
Newer Intel PCHs with LPSS have the same Designware controllers than Haswell but ACPI IDs are different. Add these IDs to the driver list. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: pl011: fix fall back from DMA to interrupt modeGuennadi Liakhovetski1-0/+2
When falling back from DMA to interrupt mode the receive interrupt has to be re-enabled to catch new incoming data. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: pl011: (cosmetic) remove superfluous register writeGuennadi Liakhovetski1-3/+1
In pl011_rx_chars() if pl011_dma_rx_trigger_dma() succeeds it will disable the receive interrupt, no need to do this again. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: amba-pl011: preseserve hardware settings during initialisationJon Medhurst1-2/+12
During initialisation, a UART may already be in use for a console, so take care to preserve things like baud rate and data format to avoid corrupting console output. Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: amba-pl011: factor out code for writing LCR_H registerJon Medhurst1-22/+17
The code to cope with a split tx/rx LCR_H register is non-trivial so put it into it's own function to avoid duplication. Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: amba-pl011: use port lock to guard control register accessJon Medhurst1-0/+6
When the pl011 is being used for a console, pl011_console_write forces the control register (CR) to enable the UART for transmission and then restores this to the original value afterwards. It does this while holding the port lock. Unfortunately, when the uart is started or shutdown - say in response to userland using the serial device for a terminal - then this updates the control register without any locking. This means we can have pl011_console_write Save CR pl011_startup Initialise CR, e.g. enable receive pl011_console_write Restore old CR with receive not enabled this result is a serial port which doesn't respond to any input. A similar race in reverse could happen when the device is shutdown. We can fix these problems by taking the port lock when updating CR. Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17Revert "serial: pl011: use DMA RX polling by default"Greg Kroah-Hartman1-1/+1
This reverts commit 17438217a6f5e33d920ed3821a4b857311cc2872 on request of Linus Walleij: Greg can you please drop or revert commit 17438217a6f5e33d920ed3821a4b857311cc2872 "serial: pl011: use DMA RX polling by default" from the TTY tree until this has been sorted out? Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17serial: clps711x: Driver refactorAlexander Shiyan1-194/+254
This is a complex patch for refactoring CLPS711X serial driver. Major changes: - Eliminate <mach/hardware.h> usage. - Devicetree support. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-16serial: 8250_dw: Fix LCR workaround regressionJames Hogan1-2/+4
Commit c49436b657d0 (serial: 8250_dw: Improve unwritable LCR workaround) caused a regression. It added a check that the LCR was written properly to detect and workaround the busy quirk, but the behaviour of bit 5 (UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the docs. On older versions this caused the check to fail and it would repeatedly force idle and rewrite the LCR register, causing delays and preventing any input from serial being received. This is fixed by masking out UART_LCR_SPAR before making the comparison. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Tim Kryger <tim.kryger@linaro.org> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Matt Porter <matt.porter@linaro.org> Cc: Markus Mayer <markus.mayer@linaro.org> Tested-by: Tim Kryger <tim.kryger@linaro.org> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-14serial: sh-sci: Convert to clk_prepare/unprepareLaurent Pinchart1-4/+4
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and clk_disable_unprepare() to get ready for the migration to the common clock framework. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Magnus Damm <damm@opensource.se> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-14serial: sh-sci: Don't enable/disable port from within break timerLaurent Pinchart1-4/+8
The break timer accesses hardware registers and thus requires the port to be enabled. It currently ensures this by enabling the port at the beginning of the timer handler, and disabling it at the end. However, the enable/disable operations call the runtime PM sync functions, which are not allowed in atomic context. The current situation is thus broken. This change relies on non-atomic code to enable/disable the port. The break timer will only be started from the IRQ handler, which already runs with the port enabled. We just need to ensure that the port won't be disabled with the timer running, and that's easily done by just cancelling the timer in the port disable function. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Magnus Damm <damm@opensource.se> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-12serial: sh-sci: Fix warnings due to improper casts and printk formatsLaurent Pinchart1-9/+10
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t variables, and cast pointers to uintptr_t instead of unsigned int where applicable. This fixes warnings on platforms where pointers and/or dma_addr_t have a different size than int. Cc: linux-serial@vger.kernel.org Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2013-12-11serial: tegra: convert to standard DMA DT bindingsStephen Warren1-18/+6
By using dma_request_slave_channel_or_err(), the DMA slave ID can be looked up from standard DT properties, and squirrelled away during channel allocation. Hence, there's no need to use a custom DT property to store the slave ID. Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Thierry Reding <treding@nvidia.com>
2013-12-11serial: tegra: use reset frameworkStephen Warren1-4/+10
Tegra's clock driver now provides an implementation of the common reset API (include/linux/reset.h). Use this instead of the old Tegra- specific API; that will soon be removed. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Thierry Reding <treding@nvidia.com>
2013-12-08tty: xuartps: Properly guard sysrq specific codeSoren Brinkmann1-0/+2
Commit 'tty: xuartps: Implement BREAK detection, add SYSRQ support' (0c0c47bc40a2e358d593b2d7fb93b50027fbfc0c) introduced sysrq support without properly guarding sysrq specific code which results in build errors when sysrq is disabled: DNAME=KBUILD_STR(xilinx_uartps)" -c -o drivers/tty/serial/.tmp_xilinx_uartps.o drivers/tty/serial/xilinx_uartps.c drivers/tty/serial/xilinx_uartps.c: In function 'xuartps_isr': drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' drivers/tty/serial/xilinx_uartps.c:247:5: error: 'struct uart_port' has no member named 'sysrq' make[3]: *** [drivers/tty/serial/xilinx_uartps.o] Error 1 Reported-by: Masanari Iida <standby24x7@gmail.com> Cc: Vlad Lungu <vlad.lungu@windriver.com> Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chipJonathan Woithe1-2/+2
Fix the initialisation of older Quatech serial cards which are fitted with the AMCC PCI Matchmaker interface chip. Signed-off-by: Jonathan Woithe (jwoithe@just42.net) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08serial: icom: dereference after free in load_code()Dan Carpenter1-2/+2
We use "fw" in the next line after we release it. I've shifted the call to release_firmware() down a couple lines to fix this. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08serial: 8250_dw: add new ACPI IDsMika Westerberg1-0/+2
Newer Intel PCHs with LPSS have the same Designware controllers than Haswell but ACPI IDs are different. Add these IDs to the driver list. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-08tty: serial: pch: don't crash if DMA enabled but not loadedSebastian Andrzej Siewior1-3/+7
if the DMA driver isn't loaded "on time" then we crash in the irq handler: | pch_uart 0000:02:0a.4: pch_request_dma:dma_request_channel FAILS(Tx) | BUG: unable to handle kernel NULL pointer dereference at (null) | IP: [<c0676ed9>] pch_uart_interrupt+0x739/0x940 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.