aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/tty (follow)
AgeCommit message (Collapse)AuthorFilesLines
2020-02-13vt: selection, close sel_buffer raceJiri Slaby1-6/+17
syzkaller reported this UAF: BUG: KASAN: use-after-free in n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741 Read of size 1 at addr ffff8880089e40e9 by task syz-executor.1/13184 CPU: 0 PID: 13184 Comm: syz-executor.1 Not tainted 5.4.7 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 Call Trace: ... kasan_report+0xe/0x20 mm/kasan/common.c:634 n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741 tty_ldisc_receive_buf+0xac/0x190 drivers/tty/tty_buffer.c:461 paste_selection+0x297/0x400 drivers/tty/vt/selection.c:372 tioclinux+0x20d/0x4e0 drivers/tty/vt/vt.c:3044 vt_ioctl+0x1bcf/0x28d0 drivers/tty/vt/vt_ioctl.c:364 tty_ioctl+0x525/0x15a0 drivers/tty/tty_io.c:2657 vfs_ioctl fs/ioctl.c:47 [inline] It is due to a race between parallel paste_selection (TIOCL_PASTESEL) and set_selection_user (TIOCL_SETSEL) invocations. One uses sel_buffer, while the other frees it and reallocates a new one for another selection. Add a mutex to close this race. The mutex takes care properly of sel_buffer and sel_buffer_lth only. The other selection global variables (like sel_start, sel_end, and sel_cons) are protected only in set_selection_user. The other functions need quite some more work to close the races of the variables there. This is going to happen later. This likely fixes (I am unsure as there is no reproducer provided) bug 206361 too. It was marked as CVE-2020-8648. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Reported-by: syzbot+59997e8d5cbdc486e6f6@syzkaller.appspotmail.com References: https://bugzilla.kernel.org/show_bug.cgi?id=206361 Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210081131.23572-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-13vt: selection, handle pending signals in paste_selectionJiri Slaby1-1/+8
When pasting a selection to a vt, the task is set as INTERRUPTIBLE while waiting for a tty to unthrottle. But signals are not handled at all. Normally, this is not a problem as tty_ldisc_receive_buf receives all the goods and a user has no reason to interrupt the task. There are two scenarios where this matters: 1) when the tty is throttled and a signal is sent to the process, it spins on a CPU until the tty is unthrottled. schedule() does not really echedule, but returns immediately, of course. 2) when the sel_buffer becomes invalid, KASAN prevents any reads from it and the loop simply does not proceed and spins forever (causing the tty to throttle, but the code never sleeps, the same as above). This sometimes happens as there is a race in the sel_buffer handling code. So add signal handling to this ioctl (TIOCL_PASTESEL) and return -EINTR in case a signal is pending. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210081131.23572-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-13serial: cpm_uart: call cpm_muram_init before registering consoleRasmus Villemoes1-0/+1
Christophe reports that powerpc 8xx silently fails to 5.6-rc1. It turns out I was wrong about nobody relying on the lazy initialization of the cpm/qe muram in commit b6231ea2b3c6 (soc: fsl: qe: drop broken lazy call of cpm_muram_init()). Rather than reinstating the somewhat dubious lazy call (initializing a currently held spinlock, and implicitly doing a GFP_KERNEL under that spinlock), make sure that cpm_muram_init() is called early enough - I thought the calls from the subsys_initcalls were good enough, but when used by console drivers, that's obviously not the case. cpm_muram_init() is safe to call twice (there's an early return if it is already initialized), so keep the call from cpm_init() - in case SERIAL_CPM_CONSOLE=n. Fixes: b6231ea2b3c6 (soc: fsl: qe: drop broken lazy call of cpm_muram_init()) Reported-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> Link: https://lore.kernel.org/r/20200213114342.21712-1-linux@rasmusvillemoes.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12tty: serial: qcom_geni_serial: Fix RX cancel command failuresatya priya1-4/+14
RX cancel command fails when BT is switched on and off multiple times. To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register instead of SE_GENI_S_CMD_CTRL_REG. As per the HPG update, handle the RX last bit after cancel command and flush out the RX FIFO buffer. Signed-off-by: satya priya <skakit@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12serial: 8250: Check UPF_IRQ_SHARED in advanceAndy Shevchenko4-5/+6
The commit 54e53b2e8081 ("tty: serial: 8250: pass IRQ shared flag to UART ports") nicely explained the problem: ---8<---8<--- On some systems IRQ lines between multiple UARTs might be shared. If so, the irqflags have to be configured accordingly. The reason is: The 8250 port startup code performs IRQ tests *before* the IRQ handler for that particular port is registered. This is performed in serial8250_do_startup(). This function checks whether IRQF_SHARED is configured and only then disables the IRQ line while testing. This test is performed upon each open() of the UART device. Imagine two UARTs share the same IRQ line: On is already opened and the IRQ is active. When the second UART is opened, the IRQ line has to be disabled while performing IRQ tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself cannot be handled, because the corresponding handler isn't registered, yet. That's because the 8250 code uses a chain-handler and invokes the corresponding port's IRQ handling routines himself. Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't disabled while performing tests and the kernel correctly detects a spurious IRQ. So, adding this flag to the DT probe solves the issue. Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the IRQF_SHARED flag can be set unconditionally as well. Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system: |irq 85: nobody cared (try booting with the "irqpoll" option) | [...] |handlers: |[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt |Disabling IRQ #85 ---8<---8<--- But unfortunately didn't fix the root cause. Let's try again here by moving IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup(). This should fix the similar issue reported for 8250_pnp case. Since this change we don't need to have custom solutions in 8250_aspeed_vuart and 8250_of drivers, thus, drop them. Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support") Reported-by: Li RongQing <lirongqing@baidu.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12tty: serial: imx: setup the correct sg entry for tx dmaFugang Duan1-1/+1
There has oops as below happen on i.MX8MP EVK platform that has 6G bytes DDR memory. when (xmit->tail < xmit->head) && (xmit->head == 0), it setups one sg entry with sg->length is zero: sg_set_buf(sgl + 1, xmit->buf, xmit->head); if xmit->buf is allocated from >4G address space, and SDMA only support <4G address space, then dma_map_sg() will call swiotlb_map() to do bounce buffer copying and mapping. But swiotlb_map() don't allow sg entry's length is zero, otherwise report BUG_ON(). So the patch is to correct the tx DMA scatter list. Oops: [ 287.675715] kernel BUG at kernel/dma/swiotlb.c:497! [ 287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 287.686075] Modules linked in: [ 287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10 [ 287.696872] Hardware name: FSL i.MX8MP EVK (DT) [ 287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO) [ 287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310 [ 287.711076] lr : swiotlb_map+0x60/0x148 [ 287.714909] sp : ffff800010003c00 [ 287.718221] x29: ffff800010003c00 x28: 0000000000000000 [ 287.723533] x27: 0000000000000040 x26: ffff800011ae0000 [ 287.728844] x25: ffff800011ae09f8 x24: 0000000000000000 [ 287.734155] x23: 00000001b7af9000 x22: 0000000000000000 [ 287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe [ 287.744776] x19: ffff000176409c10 x18: 000000000000002e [ 287.750087] x17: 0000000000000000 x16: 0000000000000000 [ 287.755397] x15: 0000000000000000 x14: 0000000000000000 [ 287.760707] x13: ffff00017f334000 x12: 0000000000000001 [ 287.766018] x11: 00000000001fffff x10: 0000000000000000 [ 287.771328] x9 : 0000000000000003 x8 : 0000000000000000 [ 287.776638] x7 : 0000000000000000 x6 : 0000000000000000 [ 287.781949] x5 : 0000000000200000 x4 : 0000000000000000 [ 287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000 [ 287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000 [ 287.797881] Call trace: [ 287.800328] swiotlb_tbl_map_single+0x1fc/0x310 [ 287.804859] swiotlb_map+0x60/0x148 [ 287.808347] dma_direct_map_page+0xf0/0x130 [ 287.812530] dma_direct_map_sg+0x78/0xe0 [ 287.816453] imx_uart_dma_tx+0x134/0x2f8 [ 287.820374] imx_uart_dma_tx_callback+0xd8/0x168 [ 287.824992] vchan_complete+0x194/0x200 [ 287.828828] tasklet_action_common.isra.0+0x154/0x1a0 [ 287.833879] tasklet_action+0x24/0x30 [ 287.837540] __do_softirq+0x120/0x23c [ 287.841202] irq_exit+0xb8/0xd8 [ 287.844343] __handle_domain_irq+0x64/0xb8 [ 287.848438] gic_handle_irq+0x5c/0x148 [ 287.852185] el1_irq+0xb8/0x180 [ 287.855327] cpuidle_enter_state+0x84/0x360 [ 287.859508] cpuidle_enter+0x34/0x48 [ 287.863083] call_cpuidle+0x18/0x38 [ 287.866571] do_idle+0x1e0/0x280 [ 287.869798] cpu_startup_entry+0x20/0x40 [ 287.873721] rest_init+0xd4/0xe0 [ 287.876949] arch_call_rest_init+0xc/0x14 [ 287.880958] start_kernel+0x420/0x44c [ 287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000) [ 287.890718] ---[ end trace 5bc44c4ab6b009ce ]--- [ 287.895334] Kernel panic - not syncing: Fatal exception in interrupt [ 287.901686] SMP: stopping secondary CPUs [ 288.905607] SMP: failed to stop secondary CPUs 0-1 [ 288.910395] Kernel Offset: disabled [ 288.913882] CPU features: 0x0002,2000200c [ 288.917888] Memory Limit: none [ 288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- Reported-by: Eagle Zhou <eagle.zhou@nxp.com> Tested-by: Eagle Zhou <eagle.zhou@nxp.com> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12vt: vt_ioctl: fix race in VT_RESIZEXEric Dumazet1-6/+11
We need to make sure vc_cons[i].d is not NULL after grabbing console_lock(), or risk a crash. general protection fault, probably for non-canonical address 0xdffffc0000000068: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000340-0x0000000000000347] CPU: 1 PID: 19462 Comm: syz-executor.5 Not tainted 5.5.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:vt_ioctl+0x1f96/0x26d0 drivers/tty/vt/vt_ioctl.c:883 Code: 74 41 e8 bd a6 84 fd 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 e4 04 00 00 48 8b 03 48 8d b8 40 03 00 00 48 89 fa 48 c1 ea 03 <42> 0f b6 14 2a 84 d2 74 09 80 fa 03 0f 8e b1 05 00 00 44 89 b8 40 RSP: 0018:ffffc900086d7bb0 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffffffff8c34ee88 RCX: ffffc9001415c000 RDX: 0000000000000068 RSI: ffffffff83f0e6e3 RDI: 0000000000000340 RBP: ffffc900086d7cd0 R08: ffff888054ce0100 R09: fffffbfff16a2f6d R10: ffff888054ce0998 R11: ffff888054ce0100 R12: 000000000000001d R13: dffffc0000000000 R14: 1ffff920010daf79 R15: 000000000000ff7f FS: 00007f7d13c12700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffd477e3c38 CR3: 0000000095d0a000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: tty_ioctl+0xa37/0x14f0 drivers/tty/tty_io.c:2660 vfs_ioctl fs/ioctl.c:47 [inline] ksys_ioctl+0x123/0x180 fs/ioctl.c:763 __do_sys_ioctl fs/ioctl.c:772 [inline] __se_sys_ioctl fs/ioctl.c:770 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:770 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x45b399 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f7d13c11c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f7d13c126d4 RCX: 000000000045b399 RDX: 0000000020000080 RSI: 000000000000560a RDI: 0000000000000003 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 0000000000000666 R14: 00000000004c7f04 R15: 000000000075bf2c Modules linked in: ---[ end trace 80970faf7a67eb77 ]--- RIP: 0010:vt_ioctl+0x1f96/0x26d0 drivers/tty/vt/vt_ioctl.c:883 Code: 74 41 e8 bd a6 84 fd 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 e4 04 00 00 48 8b 03 48 8d b8 40 03 00 00 48 89 fa 48 c1 ea 03 <42> 0f b6 14 2a 84 d2 74 09 80 fa 03 0f 8e b1 05 00 00 44 89 b8 40 RSP: 0018:ffffc900086d7bb0 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffffffff8c34ee88 RCX: ffffc9001415c000 RDX: 0000000000000068 RSI: ffffffff83f0e6e3 RDI: 0000000000000340 RBP: ffffc900086d7cd0 R08: ffff888054ce0100 R09: fffffbfff16a2f6d R10: ffff888054ce0998 R11: ffff888054ce0100 R12: 000000000000001d R13: dffffc0000000000 R14: 1ffff920010daf79 R15: 000000000000ff7f FS: 00007f7d13c12700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffd477e3c38 CR3: 0000000095d0a000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: stable <stable@vger.kernel.org> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20200210190721.200418-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10vt: fix scrollback flushing on background consolesNicolas Pitre1-2/+13
Commit a6dbe4427559 ("vt: perform safe console erase in the right order") provided fixes to an earlier commit by gathering all console scrollback flushing operations in a function of its own. This includes the invocation of vc_sw->con_switch() as previously done through a update_screen() call. That commit failed to carry over the con_is_visible() conditional though, as well as cursor handling, which caused problems when "\e[3J" was written to a background console. One could argue for preserving the call to update_screen(). However this does far more than we need, and it is best to remove scrollback assumptions from it. Instead let's gather the minimum needed to actually perform scrollback flushing properly in that one place. While at it, let's document the vc_sw->con_switch() side effect being relied upon. Signed-off-by: Nicolas Pitre <nico@fluxnic.net> Reported-and-tested-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2001281205560.1655@knanqh.ubzr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10tty: serial: tegra: Handle RX transfer in PIO mode if DMA wasn't startedDmitry Osipenko1-19/+16
It is possible to get an instant RX timeout or end-of-transfer interrupt before RX DMA was started, if transaction is less than 16 bytes. Transfer should be handled in PIO mode in this case because DMA can't handle it. This patch brings back the original behaviour of the driver that was changed by accident by a previous commit, it fixes occasional Bluetooth HW initialization failures which I started to notice recently. Fixes: d5e3fadb7012 ("tty: serial: tegra: Activate RX DMA transfer by request") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200209164415.9632-1-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 modeNicolas Ferre1-1/+2
In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions. Prevent the rx restart that is implemented in RS485 or ISO7816 modes when calling atmel_stop_tx() by using the atomic information tasklet_shutdown that is already in place for this purpose. Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences") Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10serdev: ttyport: restore client ops on deregistrationJohan Hovold2-6/+5
The serdev tty-port controller driver should reset the tty-port client operations also on deregistration to avoid a NULL-pointer dereference in case the port is later re-registered as a normal tty device. Note that this can only happen with tty drivers such as 8250 which have statically allocated port structures that can end up being reused and where a later registration would not register a serdev controller (e.g. due to registration errors or if the devicetree has been changed in between). Specifically, this can be an issue for any statically defined ports that would be registered by 8250 core when an 8250 driver is being unbound. Fixes: bed35c6dfa6a ("serdev: add a tty port controller driver") Cc: stable <stable@vger.kernel.org> # 4.11 Reported-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200210145730.22762-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDEDaniel Golle1-0/+8
On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x should not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-09Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuildLinus Torvalds1-1/+1
Pull more Kbuild updates from Masahiro Yamada: - fix randconfig to generate a sane .config - rename hostprogs-y / always to hostprogs / always-y, which are more natual syntax. - optimize scripts/kallsyms - fix yes2modconfig and mod2yesconfig - make multiple directory targets ('make foo/ bar/') work * tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: make multiple directory targets work kconfig: Invalidate all symbols after changing to y or m. kallsyms: fix type of kallsyms_token_table[] scripts/kallsyms: change table to store (strcut sym_entry *) scripts/kallsyms: rename local variables in read_symbol() kbuild: rename hostprogs-y/always to hostprogs/always-y kbuild: fix the document to use extra-y for vmlinux.lds kconfig: fix broken dependency in randconfig-generated .config
2020-02-08Fix up remaining devm_ioremap_nocache() in SGI IOC3 8250 UART driverLinus Torvalds1-1/+1
This is a merge error on my part - the driver was merged into mainline by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux") over a week ago, but nobody apparently noticed that it didn't actually build due to still having a reference to the devm_ioremap_nocache() function, removed a few days earlier through commit 6a1000bd2703 ("Merge tag 'ioremap-5.6' of git://../ioremap"). Apparently this didn't get any build testing anywhere. Not perhaps all that surprising: it's restricted to 64-bit MIPS only, and only with the new SGI_MFD_IOC3 support enabled. I only noticed because the ioremap conflicts in the ARM SoC driver update made me check there weren't any others hiding, and I found this one. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-02-08Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds1-184/+201
Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms: - Nvidia: Fuse support for Tegra194, continued memory controller pieces for Tegra30 - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC - NXP/FSL: i.MX8MP SoC driver pieces - TI Keystone: ring accelerator driver - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs. - Xilinx ZynqMP: feature checking interface for firmware. Mailbox communication for power management - Overall support patch set for cpuidle on more complex hierarchies (PSCI-based) and misc cleanups, refactorings of Marvell, TI, other platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits) drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists MAINTAINERS: Add brcmstb PCIe controller entry soc/tegra: fuse: Unmap registers once they are not needed anymore soc/tegra: fuse: Correct straps' address for older Tegra124 device trees soc/tegra: fuse: Warn if straps are not ready soc/tegra: fuse: Cache values of straps and Chip ID registers memory: tegra30-emc: Correct error message for timed out auto calibration memory: tegra30-emc: Firm up hardware programming sequence memory: tegra30-emc: Firm up suspend/resume sequence soc/tegra: regulators: Do nothing if voltage is unchanged memory: tegra: Correct reset value of xusb_hostr soc/tegra: fuse: Add APB DMA dependency for Tegra20 bus: tegra-aconnect: Remove PM_CLK dependency dt-bindings: mediatek: add MT6765 power dt-bindings soc: mediatek: cmdq: delete not used define memory: tegra: Add support for the Tegra194 memory controller memory: tegra: Only include support for enabled SoCs memory: tegra: Support DVFS on Tegra186 and later ...
2020-02-04proc: convert everything to "struct proc_ops"Alexey Dobriyan1-4/+4
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in seq_file.h. Conversion rule is: llseek => proc_lseek unlocked_ioctl => proc_ioctl xxx => proc_xxx delete ".owner = THIS_MODULE" line [akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c] [sfr@canb.auug.org.au: fix kernel/sched/psi.c] Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-02-04kbuild: rename hostprogs-y/always to hostprogs/always-yMasahiro Yamada1-1/+1
In old days, the "host-progs" syntax was used for specifying host programs. It was renamed to the current "hostprogs-y" in 2004. It is typically useful in scripts/Makefile because it allows Kbuild to selectively compile host programs based on the kernel configuration. This commit renames like follows: always -> always-y hostprogs-y -> hostprogs So, scripts/Makefile will look like this: always-$(CONFIG_BUILD_BIN2C) += ... always-$(CONFIG_KALLSYMS) += ... ... hostprogs := $(always-y) $(always-m) I think this makes more sense because a host program is always a host program, irrespective of the kernel configuration. We want to specify which ones to compile by CONFIG options, so always-y will be handier. The "always", "hostprogs-y", "hostprogs-m" will be kept for backward compatibility for a while. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-01-31Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds3-0/+110
Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ...
2020-01-29Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds70-749/+1085
Pull tty/serial driver updates from Greg KH: "Here are the big set of tty and serial driver updates for 5.6-rc1 Included in here are: - dummy_con cleanups (touches lots of arch code) - sysrq logic cleanups (touches lots of serial drivers) - samsung driver fixes (wasn't really being built) - conmakeshash move to tty subdir out of scripts - lots of small tty/serial driver updates All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits) tty: n_hdlc: Use flexible-array member and struct_size() helper tty: baudrate: SPARC supports few more baud rates tty: baudrate: Synchronise baud_table[] and baud_bits[] tty: serial: meson_uart: Add support for kernel debugger serial: imx: fix a race condition in receive path serial: 8250_bcm2835aux: Document struct bcm2835aux_data serial: 8250_bcm2835aux: Use generic remapping code serial: 8250_bcm2835aux: Allocate uart_8250_port on stack serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER serial: 8250_bcm2835aux: Fix line mismatch on driver unbind serial_core: Remove unused member in uart_port vt: Correct comment documenting do_take_over_console() vt: Delete comment referencing non-existent unbind_con_driver() arch/xtensa/setup: Drop dummy_con initialization arch/x86/setup: Drop dummy_con initialization arch/unicore32/setup: Drop dummy_con initialization arch/sparc/setup: Drop dummy_con initialization arch/sh/setup: Drop dummy_con initialization arch/s390/setup: Drop dummy_con initialization ...
2020-01-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds4-4/+4
Pull networking updates from David Miller: 1) Add WireGuard 2) Add HE and TWT support to ath11k driver, from John Crispin. 3) Add ESP in TCP encapsulation support, from Sabrina Dubroca. 4) Add variable window congestion control to TIPC, from Jon Maloy. 5) Add BCM84881 PHY driver, from Russell King. 6) Start adding netlink support for ethtool operations, from Michal Kubecek. 7) Add XDP drop and TX action support to ena driver, from Sameeh Jubran. 8) Add new ipv4 route notifications so that mlxsw driver does not have to handle identical routes itself. From Ido Schimmel. 9) Add BPF dynamic program extensions, from Alexei Starovoitov. 10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes. 11) Add support for macsec HW offloading, from Antoine Tenart. 12) Add initial support for MPTCP protocol, from Christoph Paasch, Matthieu Baerts, Florian Westphal, Peter Krystad, and many others. 13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu Cherian, and others. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits) net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC udp: segment looped gso packets correctly netem: change mailing list qed: FW 8.42.2.0 debug features qed: rt init valid initialization changed qed: Debug feature: ilt and mdump qed: FW 8.42.2.0 Add fw overlay feature qed: FW 8.42.2.0 HSI changes qed: FW 8.42.2.0 iscsi/fcoe changes qed: Add abstraction for different hsi values per chip qed: FW 8.42.2.0 Additional ll2 type qed: Use dmae to write to widebus registers in fw_funcs qed: FW 8.42.2.0 Parser offsets modified qed: FW 8.42.2.0 Queue Manager changes qed: FW 8.42.2.0 Expose new registers and change windows qed: FW 8.42.2.0 Internal ram offsets modifications MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver Documentation: net: octeontx2: Add RVU HW and drivers overview octeontx2-pf: ethtool RSS config support octeontx2-pf: Add basic ethtool support ...
2020-01-27Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremapLinus Torvalds20-32/+32
Pull ioremap updates from Christoph Hellwig: "Remove the ioremap_nocache API (plus wrappers) that are always identical to ioremap" * tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap: remove ioremap_nocache and devm_ioremap_nocache MIPS: define ioremap_nocache to ioremap
2020-01-23tty: n_hdlc: Use flexible-array member and struct_size() helperGustavo A. R. Silva1-6/+5
Old code in the kernel uses 1-byte and 0-byte arrays to indicate the presence of a "variable length array": struct something { int length; u8 data[1]; }; struct something *instance; instance = kmalloc(sizeof(*instance) + size, GFP_KERNEL); instance->length = size; memcpy(instance->data, source, size); There is also 0-byte arrays. Both cases pose confusion for things like sizeof(), CONFIG_FORTIFY_SOURCE, etc.[1] Instead, the preferred mechanism to declare variable-length types such as the one above is a flexible array member[2] which need to be the last member of a structure and empty-sized: struct something { int stuff; u8 data[]; }; Also, by making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertenly introduced[3] to the codebase from now on. Lastly, make use of the struct_size() helper to safely calculate the allocation size for instances of struct n_hdlc_buf and avoid any potential type mistakes[4][5]. [1] https://github.com/KSPP/linux/issues/21 [2] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") [4] https://lore.kernel.org/lkml/60e14fb7-8596-e21c-f4be-546ce39e7bdb@embeddedor.com/ [5] commit 553d66cb1e86 ("iommu/vt-d: Use struct_size() helper") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200121172138.GA3162@embeddedor Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22tty: baudrate: SPARC supports few more baud ratesAndy Shevchenko1-2/+4
According to termbits.h SPARC supports few more baud rates than currently defined in tty_baudrate.c. Append supported ones to baud_table[] and baud_bits[]. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200115224124.74684-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22tty: baudrate: Synchronise baud_table[] and baud_bits[]Andy Shevchenko1-15/+9
Synchronize baud rate tables baud_table and baud_bits with each other for better readability. This makes clear what is being used for SPARC. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200115224124.74684-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22tty: serial: meson_uart: Add support for kernel debuggerJulien Masson1-0/+65
The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch implement the serial polling hooks for the meson_uart to be used for KGDB debugging over serial line. Signed-off-by: Julien Masson <jmasson@baylibre.com> Link: https://lore.kernel.org/r/867e1klo48.fsf@julienm-fedora-R90NQGV9.i-did-not-set--mail-host-address--so-tickle-me Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: imx: fix a race condition in receive pathUwe Kleine-König1-13/+38
The main irq handler function starts by first masking disabled interrupts in the status register values to ensure to only handle enabled interrupts. This is important as when the RX path in the hardware is disabled reading the RX fifo results in an external abort. This checking must be done under the port lock, otherwise the following can happen: CPU1 | CPU2 | irq triggers as there are chars | in the RX fifo | | grab port lock imx_uart_int finds RRDY enabled | and calls imx_uart_rxint which | has to wait for port lock | | disable RX (e.g. because we're | using RS485 with !RX_DURING_TX) | | release port lock read from RX fifo with RX | disabled => exception | So take the port lock only once in imx_uart_int() instead of in the functions called from there. Reported-by: Andre Renaud <arenaud@designa-electronics.com> Cc: stable@vger.kernel.org Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Document struct bcm2835aux_dataLukas Wunner1-0/+5
Document the driver private data of the BCM2835 auxiliary UART so that upcoming commits may add further members with proper kerneldoc. Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/aea363c27fd541dba96d2ebfeee4f596c6d34932.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Use generic remapping codeLukas Wunner1-5/+3
On probe the bcm2835aux UART driver misreports the register base address as 0x0: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550 That's because the driver remaps the registers itself. Take advantage of the generic remapping code in serial8250_request_std_resource() to get a message with the correct address and to simplify the driver. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Martin Sperl <kernel@martin.sperl.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/7d1a9bdb05090d8e465fd15cd26d6e81538d07f9.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Allocate uart_8250_port on stackLukas Wunner1-18/+15
The bcm2835aux UART driver stores a struct uart_8250_port in its private data even though it's only passed once to serial8250_register_8250_port() (which copies all relevant data) and becomes obsolete afterwards. Allocate the struct on the stack instead for simplicity and to conserve memory. The driver also initializes a spinlock in the struct which is never used. Drop that as well. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Martin Sperl <kernel@martin.sperl.org> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/421d3aed4c34cc8447ac9c26c320961f1b787f11.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFERLukas Wunner1-2/+3
Suppress a gratuitous error message if serial8250_register_8250_port() returns -EPROBE_DEFER. Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/6aea0eacf3bfa73fe2d81082cc723265413410c8.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFERPhil Elwell1-1/+2
Suppress a gratuitous error message if devm_clk_get() returns -EPROBE_DEFER. Signed-off-by: Phil Elwell <phil@raspberrypi.org> [lukas: extend commit message] Signed-off-by: Lukas Wunner <lukas@wunner.de> Reviewed-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/deafc13cdfd7a31c6a81b0db95adcd3599accc26.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-22serial: 8250_bcm2835aux: Fix line mismatch on driver unbindLukas Wunner1-1/+1
Unbinding the bcm2835aux UART driver raises the following error if the maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS): (NULL device *): Removing wrong port: a6f80333 != fa20408b That's because bcm2835aux_serial_probe() retrieves UART line number 1 from the devicetree and stores it in data->uart.port.line, while serial8250_register_8250_port() instead uses UART line number 0, which is stored in data->line. On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line, which contains the wrong number. Fix it. The issue does not occur if the maximum number of 8250 UARTs is >= 2. Fixes: bdc5f3009580 ("serial: bcm2835: add driver for bcm2835-aux-uart") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.6+ Cc: Martin Sperl <kernel@martin.sperl.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-19Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2-2/+11
2020-01-16Merge tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/driversOlof Johansson1-184/+201
NXP/FSL SoC driver updates for v5.6 QUICC Engine drivers - Improve the QE drivers to be compatible with ARM/ARM64/PPC64 architectures - Various cleanups to the QE drivers * tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits) soc: fsl: qe: remove set but not used variable 'mm_gc' soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32 net/wan/fsl_ucc_hdlc: reject muram offsets above 64K net/wan/fsl_ucc_hdlc: fix reading of __be16 registers net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE() soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c soc: fsl: qe: drop pointless check in qe_sdma_init() soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init() soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path soc: fsl: qe: drop broken lazy call of cpm_muram_init() soc: fsl: qe: make cpm_muram_free() ignore a negative offset soc: fsl: qe: make cpm_muram_free() return void soc: fsl: qe: change return type of cpm_muram_alloc() to s32 serial: ucc_uart: access __be32 field using be32_to_cpu serial: ucc_uart: limit brg-frequency workaround to PPC32 serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe() serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32 ... Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-14vt: Correct comment documenting do_take_over_console()Lukas Wunner1-1/+1
Commit 3e795de7631b ("[PATCH] VT binding: Add binding/unbinding support for the VT console") introduced a code comment claiming that "do_take_over_console is basically a register followed by unbind". However the function actually performs a register followed by *bind*. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Antonino A. Daplas <adaplas@gmail.com> Link: https://lore.kernel.org/r/a500f005ba7013ca8165a6d42f59b2183d56114f.1578574427.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14vt: Delete comment referencing non-existent unbind_con_driver()Lukas Wunner1-1/+0
Commit c1f5e38a5d35 ("vt: delete unneeded function unbind_con_driver") removed unbind_con_driver() but retained a comment referencing the function. Delete it. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Wang YanQing <udknight@gmail.com> Link: https://lore.kernel.org/r/4d77a67d77a1c699e9a6cc3e73044c31c02d60b5.1578574427.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14vt: Initialize conswitchp to dummy_con if unsetArvind Sankar1-2/+3
If the arch setup code hasn't initialized conswitchp yet, set it to dummy_con in con_init. This will allow us to drop the dummy_con initialization that's done in almost every architecture. Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Link: https://lore.kernel.org/r/20191218214506.49252-3-nivedita@alum.mit.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: synclink_gt: Adjust indentation in several functionsNathan Chancellor1-9/+9
Clang warns: ../drivers/tty/synclink_gt.c:1337:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (C_CRTSCTS(tty)) { ^ ../drivers/tty/synclink_gt.c:1335:2: note: previous statement is here if (I_IXOFF(tty)) ^ ../drivers/tty/synclink_gt.c:2563:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) ^ ../drivers/tty/synclink_gt.c:2561:2: note: previous statement is here if (I_INPCK(info->port.tty)) ^ ../drivers/tty/synclink_gt.c:3221:3: warning: misleading indentation; statement is not part of the previous 'else' [-Wmisleading-indentation] set_signals(info); ^ ../drivers/tty/synclink_gt.c:3219:2: note: previous statement is here else ^ 3 warnings generated. The indentation on these lines is not at all consistent, tabs and spaces are mixed together. Convert to just using tabs to be consistent with the Linux kernel coding style and eliminate these warnings from clang. Link: https://github.com/ClangBuiltLinux/linux/issues/822 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Link: https://lore.kernel.org/r/20191218023912.13827-1-natechancellor@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: synclinkmp: Adjust indentation in several functionsNathan Chancellor1-12/+12
Clang warns: ../drivers/tty/synclinkmp.c:1456:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (C_CRTSCTS(tty)) { ^ ../drivers/tty/synclinkmp.c:1453:2: note: previous statement is here if (I_IXOFF(tty)) ^ ../drivers/tty/synclinkmp.c:2473:8: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] info->port.tty->hw_stopped = 0; ^ ../drivers/tty/synclinkmp.c:2471:7: note: previous statement is here if ( debug_level >= DEBUG_LEVEL_ISR ) ^ ../drivers/tty/synclinkmp.c:2482:8: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] info->port.tty->hw_stopped = 1; ^ ../drivers/tty/synclinkmp.c:2480:7: note: previous statement is here if ( debug_level >= DEBUG_LEVEL_ISR ) ^ ../drivers/tty/synclinkmp.c:2809:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) ^ ../drivers/tty/synclinkmp.c:2807:2: note: previous statement is here if (I_INPCK(info->port.tty)) ^ ../drivers/tty/synclinkmp.c:3246:3: warning: misleading indentation; statement is not part of the previous 'else' [-Wmisleading-indentation] set_signals(info); ^ ../drivers/tty/synclinkmp.c:3244:2: note: previous statement is here else ^ 5 warnings generated. The indentation on these lines is not at all consistent, tabs and spaces are mixed together. Convert to just using tabs to be consistent with the Linux kernel coding style and eliminate these warnings from clang. Link: https://github.com/ClangBuiltLinux/linux/issues/823 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Link: https://lore.kernel.org/r/20191218024720.3528-1-natechancellor@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14serial: xilinx_uartps: set_mctrl sets RTS and DTRMaarten Brock1-0/+4
set_mctrl now sets RTS and DTR. Signed-off-by: Maarten Brock <m.brock@vanmierlo.com> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1574687731-21563-3-git-send-email-shubhrajyoti.datta@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14serial: xilinx_uartps: set_termios sets flowcontrolMaarten Brock1-5/+9
Let set_termios enable/disable automatic flow control. set_mctrl should not touch automatic flow control. Signed-off-by: Maarten Brock <m.brock@vanmierlo.com> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1574687731-21563-2-git-send-email-shubhrajyoti.datta@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14serial: xilinx_uartps: Let get_mctrl return statusMaarten Brock1-3/+25
Some of the applications like microcom do not work if modem is disabled. To fix them we always return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR instead of 0 when using cts_override. Make get_mctrl return actual status when not using cts_override. Signed-off-by: Maarten Brock <m.brock@vanmierlo.com> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Link: https://lore.kernel.org/r/1574687731-21563-1-git-send-email-shubhrajyoti.datta@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty/serial: 8250_exar: use true,false for bool variableZheng Bin1-3/+3
Fixes coccicheck warning: drivers/tty/serial/8250/8250_exar.c:189:6-17: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/8250/8250_exar.c:197:3-14: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/8250/8250_exar.c:199:3-14: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Link: https://lore.kernel.org/r/1578881777-65475-5-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty/serial: atmel: use true,false for bool variableZheng Bin1-3/+3
Fixes coccicheck warning: drivers/tty/serial/atmel_serial.c:1062:1-23: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/atmel_serial.c:1261:1-23: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/atmel_serial.c:1688:3-25: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Link: https://lore.kernel.org/r/1578881777-65475-4-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty/serial: kgdb_nmi: use true,false for bool variableZheng Bin1-2/+2
Fixes coccicheck warning: drivers/tty/serial/kgdb_nmi.c:121:6-13: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/kgdb_nmi.c:133:2-9: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Link: https://lore.kernel.org/r/1578881777-65475-3-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: synclink_gt: use true,false for bool variableZheng Bin1-1/+1
Fixes coccicheck warning: drivers/tty/synclink_gt.c:2101:3-19: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Link: https://lore.kernel.org/r/1578881777-65475-2-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: serial: msm_serial: RX SW/FIFO mode fallbackLoic Poulain1-1/+17
During db410c stress test and when the system is low on memory, the UART/console becomes unresponsive and never recover back. This has been narrowed down to the msm_start_rx_dma which does not manage error cases correctly (e.g. dma mapping failure), indeed, when an error happens, dma transfer is simply discarded and so never completed, leading to unconfigured RX path. This patch fixes this issue by switching to SW/FIFO mode in case of DMA issue. This mainly consists in resetting the receiver to apply RX BAM/DMA disabling change and re-enabling the RX level and stale interrupts (previously disabled for DMA transfers). The DMA will be re-enabled once memory is available since the SW/FIFO read function (msm_handle_rx_dm) retries to start dma on completion. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/1578646684-17379-1-git-send-email-loic.poulain@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14serial: 8250: Support disabling mdelay-filled probes of 16550A variantsJosh Triplett2-0/+13
The 8250 driver can probe for many variants of the venerable 16550A serial port. Some of those probes involve long (20ms) mdelay calls, which delay system boot. Modern systems and virtual machines don't have those variants. Provide a Kconfig option to disable probes for 16550A variants. Disabling this speeds up the boot of a virtual machine with a serial console by more than 20ms (a substantial fraction of the ~100ms needed to boot a carefully configured VM). Before: [ +0.021919] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A After: [ +0.000097] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A Signed-off-by: Josh Triplett <josh@joshtriplett.org> Link: https://lore.kernel.org/r/20200111022513.GA166267@localhost Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: serial: tegra: Optimize DMA buffer synchronizationDmitry Osipenko1-7/+9
Synchronize only the dirty part of DMA buffer in order to avoid unnecessary overhead of syncing of the clean part, which is the case of every serial DMA transfer in practice. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200112180919.5194-3-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14tty: serial: tegra: Activate RX DMA transfer by requestDmitry Osipenko1-32/+46
This allows DMA engine to go into runtime-suspended mode whenever there is no data to receive, instead of keeping DMA active all the time while TTY is opened (i.e. permanently active in practice, like in the case of UART Bluetooth). Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200112180919.5194-2-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.